AS AS TO BUILDING NO 8A AND ITS CONNECTED ALLIED WORKS TO ADMIN OFFICE LOCATED INSIDE ND(V) AND SPECIAL REPAIR OF IRON GATE AT ARSR IN DOLPHIN HILLS, PROVISION OF PORCH AT THE ENTRANCE OF MAIN BUILDING AND PARKING SHED AT MMT AND IU(E), VISAKHAPATN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish off the premises complete all as specified and directed.

M & L for coloured glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick screed bed / backing coat in cement mortor 1:4 complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish off the premises complete all as directed.

M & L for 40 mm thick, plain cement concrete 1:2:4, type B-1 (using 20.0 mm graded stone aggregate) as in sub-base of flooring, etc and finished the surface even and rough complete all as specified and directed.

M & L for Machine cut kota stone slab flooring 20 to 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing over and including 15 mm thick, screed bed in cement mortar 1:6 complete all as specified and directed.

Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of three track windows ,door, including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed

Providing and fixing Powder coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge complete all as specified and directed.

S & F 5.5 mm thick, sheet glass, ordinary quality and glazing with beading for door/window etc in square exceeding 0.5 Sqm in each pane complete all as specified and directed. (Note: The cost of glazing beads included with the unti quoted rate of respective shutter)

S & F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing rubbish to to a distance not exceeding 100m complete all as specified and directed

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new platered surface of wall and applying two coats of oil bound distemper over a coat of primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed. Note :- Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS

M&L for preparation of old decorated surface of wall by complete removal of existing treatment, washing, rubbing, stopping etc and applying two coats of weather proof 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre , dart pick up resistant,silicon enhanced,UV resistant and PU enhanced property over a coat of alkali resistant primer including all necessary scaffolding complete all as specified and as directed. Note :- Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS (ii) Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer)

M & L for preparing old plastered surfaces of ceiling, etc and applying one coat of white wash complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description n.exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for Preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint complete all as specified and directed.

M & L for 100 mm thick, plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub-base of flooring, paving etc complete all as specified and directed.

M & L for Sand filling under floors or in foundations including spreading, levelling, watering and consolidation complete all as specified and directed.

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M & L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, coloured / multicoloured, glossy finish , set, jointed and pointed white cement slurry and pigments in floors, etc including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for providing, cement concrete 1:2:4 type B-1 using 20 mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edges and coping including nescssary formwork complete all as specified and directed

Disamntling RCC post or struts any section, including taking out embedded portion in concrete and making good disturbed ground including cleaning and cutting of grass, shrubs, bushes, etc complete all as specified and directed.

Dismantling fencing wire mesh, any type complete complete all as specified and directed.

Excavating in post holes (or similar holes) each n. exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface in soft/loose soil complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Mild Steel Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 ® complete all as specified and directed.

S & F of Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut with diameter of shank 5 to 15 mm, but length of bolt exc 5cm but n exc 10cm long long all as specified and as directed.

M & L for mild steel round bar 10mm dia and over cut into length, bend to shape required including cranking bending spirally for hoping as in tie bar for fixing chain link fencing complete all as specified and directed.

S & F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed.

Supply only chain link fencing made out of 3.10 mm dia galvanised iron wire, made up into mattress or cages of any size, straining and fixing to post complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed.

M & L for Preparation of new or previously untreated steel or iron surfaces of any description, not otherwise described, n.exc 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc and disposal of debris and rubbish to a distance n.exe 100 m as directed by the Engr-in-Charge.

M & L for brick work with fly ash bricks, straight or curved on plan to any radius, built in cement mortar 1:6 using old size brick complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in surface channel, drains etc complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

Demolition of reinforced cement concrete in any position not otherwise specifically provided for and removing rubbish to a distance n.exe 100 m complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab (For manhole etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar 1:6 including necessary form, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

S & F high strength corrosion resistant TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

M&L for Plain Cement Concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Use and waste of form work to formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded stone aggregate as in foundation, plinth beams, bases of columns and mass concrete complete all as specified and directed by Engineer-in-Charge.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions flat or curved of concrete complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc. complete all as specified and directed by Engineer-in-Charge.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves ,plinth beam including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span etc.complete all as specified and directed by Engineer-in-Charge.

S & F high strength corrosion resistant TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M&L for preparation of new platered surface of wall and applying two coats of weather proof 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre, dart pick up resistant,silicon enhanced,UV resistant and PU enhanced property over a coat of alkali resistant primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces including all necessary scaffolding,complete all as specified and directed. Note :- Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-450 Gde-E-250 Quality -A complete all as specified and directed.

S & F rolled mild plates (plain or chequered) channels, square cut or notched, forming holes with riveted, bolted or welded attachment conforming to Fe 410W Gr E-250, quality-A complete all as specified and directed.

S & F MS steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St-240 complete all as speicfied and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

M&L for preparation of structural steel,iron surfaces of any description embading in brick or concrete,surface exceeding 10cm in width or girth and applying two coats of black bituminous paint complete all as specified and directed

Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts ,depth of embedded portion of holdfasts or lugs measured from the face of the jamb exe one brick but no exc two bricks into the wall and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M & L for plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

M & L for Precast reinforced cement concrete 1:2:4, type B-0 (using 12.5mm graded stone aggregate) louvres and jallies, 50mm thick including all mouldings and set in cement mortar 1:4 including dismantling of existing one and removing debries upto outside MD Land complete all as specified and directed.

Material and labour for applying one coat of oil bound washable distemper to old decorated plastered (distempered) surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed by Engineer -in-Charge. Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, as in vertical surfaces as in skirting, dado etc, including 10 mm thick screed bed in cement mortor 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

S & F 45 Watt, 230 Volts AC Post Top Lantern, outdoor type with decorative post top for 360 Degree indirect light, IP 65 protection with impact and corrosion reisitant complete with driver and lamp, fixing accessories and connecting up with suitable copper conductor complete all as specified and directed. (Make: Bajaj BGCTN 45W LED WW/WH or equivelant of make as per list of manufacturer)

Supply, fixing thermoplastic circuit breaker boxes 1 row 4 modules with IP 65 protection and necessary fixing arrangements complete all as specified and as directed Make: Hensel cat part No. KV 7104 or equivalent make as per List of Manufacturer's mentioned in PS)

Supply, fixing, commissioning and testing in repairs MCB SP 6 to 32 Amps, 240 Volts, 10KA, C Curve, complete all as specified and as directed

M & L for Sub main wiring with 2 runs of Single core 1.5 sqmm PVC insulated, unseathed, multi stranded FRLSH (ISI marked) copper cable drawn through and including PVC conduit of 20 mm dia with all accesories and fittings along with 1 run of single core 1.50 sqmm PVC insulated ,unseathed multi stranded FRLSH (ISI marked) copper cable as earth continuity conductor complete all as specified and as directed. (Note :-Two runs of 1.5 sqmm and one runs of 1.5 sqmm cable as earth wire and one run of PVC conduit shall be measured as one length)

SAI SRINIVAS CONSTRUCTIONS (BID ID -3294162)

GVR CONSTRUCTIONS (BID ID -3294572)

SV CONSTRUCTION (BID ID -3292768)

JAYAM BUILD CONSTRUCTIONS (BID ID -3295783)

M B CONSTRUCTIONS (BID ID -3294591)

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS (BID ID -3294042)