SPECIAL REPAIR TO BLDG NO. P-7, P-19 AND P-38 AT NHO UNDER AGE B/R-III OF GE CLEMENT TOWN DEHRADUN

Amount

Demolition of cement concrete (un-reinforced) in ground floor and pavings etc n. exc 15cm thickness (below or above ground level) and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Dismantling of boarding of any type/size as in CB/wardrobes or fixed in any position in hardware (if any) etc complete all as specified.

Dismantling timber scantling 40 Sqcm and over in section in any position complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets as in roof coverings complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size exc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed.

Taking down shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed.

M&L for brick work with sub class "B" old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for half brick thick wall of brick work with subclass ‘B’ bricks, straight or curved on plan to any radius built in CM (1:4) complete all as specified and directed.

S&F mild steel framed work as in Staging for water tanks and the like incl caps, bases etc built up from two or more beam or channel section or angles, MS hollow pipes, MS plates incl lattice bars, stiffeners, gusset plates etc conforming to Fe-290, Gde-E-250 complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for 50mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed.

M&L for PCC (1:2:4) type B0 (using 12.50mm stone aggregate) mixed with SBR Latex liquid polymer (mixed as per manufacture instructions as in Sunken floor and vertical faces of walls to ease up about corners with cement concrete including using form work (straight or curved) as required complete all as specified and directed. Nate : The cost SBR Latex deemed included in quoted rate.

M&L for Non- skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick, of following size, as in floor etc with and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622.2006, Group B II with average water absorption between 0.5% to 3%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 5.0% (Max deviation). Centre & Edge curvature and warpage + 0.50% (Max deviation). Breaking strength 1300 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed :- Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE (I).

Area of each tile exc 0.06 Sqm but not exc 0.11 Sqm.

Area of each tile exc 0.18 Sqm but not exc 0.38 Sqm thickness 9-10mm.

Description same all as per item No 27 but as in skirting/dado including 10mm thick rendering in CM (1:3) complete all as specified and directed.

M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8mm thick, as in dado etc including 10mm thick rendering in CM (1:3), set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed. Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I)

M&L for 18-20mm thick granite stone slab (of any type) work (table rubbed and mirror finish polished) in steps, jambs, pillars, window-cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for rubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 15mm thick screed bed in cement mortar (1:4) for following size of tile complete all as specified and as directed:-

30cm x 30cm x 25mm thick

S&F pressed steel frames made out of 1.25mm thick mild steel sheets for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of red oxide primer including cutting holes and making good in PCC (1:2:4) type B-1 using 20 mm graded stone aggregate, of following size complete all as specified and as directed:- Note : 10mm deformed bar shall be provided in bottom portion in each frame. The rate for the same is included in rate quoted against this item.

125mm x60mm size

105mm x60mm size

M&L for PCC (1:3:6) type C1 (using 20mm graded aggregate stone aggregate) as in hold fast blocks including filling of pressed steel framing and complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable and variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

50mm x 100mm size

65mm x100mm size

65mm x125mm size

S&F Factory Made 30mm thick 100% Solid WPC Single extruded ( Wood polymer Composite ) Moulded Door Shutter Spray Painted with solvent based colour, of required size with 2,4 or 6 raised panel design on front side with 10mm deep mould on single side with grain texture comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 600 kg/cbm manufactured by an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company.

M&L for 30mm thick factory made solid WPC (wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texteure, including stainless steel wire mesh shall be fixed with 15 x15 mm square tube in side rails with screwing 8 x 28 heat metal zink coated screw can be remove or fix again after changing of wire mesh, when needed. The density of the shall be as per manufacture instruction compete all as specified and directed.

S&F three track Pre-coated Steel Sliding Window System fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Windows Section for three track external frame should be of 44 x 107mm , Section for window glass shutter should be of 36 x 50 mm, if required Section for shutter horizontal mullion should be 22mm x 60mm, The windows should be paneled with 5mm thick Plain Float glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. Touch lock to be provided for window shuttes Sections are to be cut to length, joined and assembled by means of corner brackets. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames.Windows shall be provided with fixed Stainless steel 32gauge wire mesh/gauze of 304grade with 144 holes per square inch for mosquito proofing with the help of nut, bolt and flat iron of 20x3mm size on top and Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 125mm centre to centre. Total Grill and wire mess unit shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions complete all as specified and directed.

S&F Pre-coated Steel fixed type Window/ Ventilator fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. The windows should be paneled with 5mm thick frosted glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Windows shall be provided with Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 125mm centre to centre. Total Grill shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions complete all as specified and directed.

S&F for window/ ventilator prepainted section of frame 72x55mm fixed to wall or concrete surface with rawl plugs made of galvanised steel powder coated and section of shutter 47x20mm, mulion section 72x50mm (Base steel as per IS 513 "D" quality galvanized as per IS 277 with zinc of 120 gms/Sqm) glazed and wire gauge shutter prepared to receive wiremesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made made of 10mm square bars powder coated fixed to window frame with screws at 150mm c/c both ways, 4 mm thick sheet glass, 0.36mm stainless steel wire cloth ieht 1.4mm aperture and necessary fittings and all builders hardware such as handles, tower bolts & stays etc complete all as specified and directed.

S&F 18mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/ bed rooms cabinet siders top and bottom and shelvers inside the cabinets complete as per manufacturer's specifications complete all as specific and directed.

S&F 18mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of singel side rigid laminate of approved colour adn other side plain white colour fixed with ss screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet shutters complete as per manufacturer's instructions complete all as specific and directed.

S&F of 100mm long Stainless steel non megnetic butt hinges, medium weight complete all as specified and directed.

S&F 150mm long, Stainless Steel non megnetic barrel tower bolts complete all as specified and directed.

S&F 100mm size Stainless Steel non megnetic handles, all as directed complete all as specified and directed.

S&F 150mm size Stainless Steel non megnetic handles, all as directed complete all as specified and directed.

S&F of 250mm long (Length of bolt) Stainless Steel non megnetic sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, and fixing bolts and sliding bolt complete all as specified and directed.

S&F 150mm Stainless Steel non megnetic Hasp and Staple, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair hydrulic Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed.

S&F in repair 300mm long MS helical ordinary rat tail rod pattern door spring including roller and roller plate etc complete of approved quality complete all as specified and directed.

S&F in repair of 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate complete all as specified and directed by Engr-in-Charge.

S&F 25mm dia drapery rod fancy powder coated wooden finish fixed to wall with wooden finale and brackets complete all as specified and directed.

S&F dust/ snake guard aluminium strip in doors of size 40x2mm with rubber at strip bottom complete all as specified and directed.

M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering in cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge. Note : WPC shall be measured and paid seperately.

M&L for 10mm thick plaster on roof, chajja and roof parapet of CM (1:3) on RCC finished even and smooth without using extra cement etc ncl taking down cement plaster complete all as specified and directed.

M&L for 5mm thick rendering in ceiling of cement mortar (1:3) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound (WPC) complete all as specified and directed .

M&L for three coats of white wash to newly plastered surfaces of ceiling including preparation of surfaces, complete all as specified and directed.

M&L for preparation of newly plastered surface of interior wall by application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer of same make all as specified and prescribed by manufacture of paint/ distemper, by using roller/ spray machine complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint/ distemper by using roller/ spray machine with and including application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of old decorated surface of interior wall by complete removal of existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer of same make all as specified and prescribed by manufacture of paint/ distemper, by using roller/ spray machine complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of old decorated surface of exterior wall by complete removal of existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint of required shade (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint/ distemper by using roller/ spray machineand with and including application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper complete all as specied and directed at site by Engineer-in-Charge.

Note for item No.65 to 68:- (i) The new/ old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction before application of distemper The cost of all material T&P and labour required for preparation of surface are deemed to be included in the rates quoted . (ii) The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii) All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv) After carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v) Before commencing the work, contractor will got the written approval from GE/ AGE (I) for the make and colour / shade (tint).

M&L for preparation of old surface on ceiling including brooming down or steel wire brushing scraping down smoke soot, muulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash on old decorated surface complete all as specified and as directed.

M&L for preparing old steel and iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing old wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and directed.

S&F for GI tubing 15mm bore, medium grade ISI marked with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked), fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

S&F for GI tubing 20 mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked) , fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 15mm bore GI tubing complete all as specified and directed.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 20mm bore GI tubing complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facing where required and pointing in Cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water pipe etc and making good, cutting not exc 10cm width or girth complete all as specified and directed.

S&F in repair 20mm dia gun metal gate valve ( ISI Marked) with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and directed.

S&F in repair 110mm dia PVC (SWR) pipe ( ISI Marked) single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed.

S&F in repair 75mm dia PVC (SWR) pipe ( ISI Marked) single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed.

S&F in repair 75mm dia PVC (SWR) floor trap ( ISI Marked) with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal ( ISI Marked) with access door complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal ( ISI Marked) with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend any radius ( ISI Marked) complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend any radius ( ISI Marked) complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend any radius with access door ( ISI Marked) complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend any radius with access door ( ISI Marked) complete all as specified and directed.

S&F 75mm bore PVC vent cowls ( ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer ( ISI Marked) complete all as specified and directed.

S&F in repair PVC waste pipe 32/40 mm dia ( ISI Marked) complete all as specified and directed.

S&F in repair stainless steel towel rail, 600mm long complete all as specified and directed. Make : Jaquar, Cat Part No ACN-1111SM or equivalent of others make as specified.

S&F in repair bib tap CP cast cooper alloy, long body, 15mm bore screwed for iron pipe complete with wall flange complete all as specified and directed. Make : Jaquar, Cat Part No CON-107KN or equivalent of others make as specified. Note for all CP fittings :- Chromium plated fitting shall be brought in store yard for approval by GE/AGE(I) and then issued subsequently for fixing at site.

S&F in repair 5mm thick beveled edge best quality looking mirror of size 600x450 mm with 30 mm PVC beading all around the glass, mounted over 3mm thick PVC sheet or 6mm thick AC bldg board, complete all as specified and directed.

S&F in repair of Sinks (ISI marked) made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair CP angular stop cock 15mm dia single way and fixed complete all as specified and directed. Make : Jaquar, Cat Part No CON-053KN or equivalent of others make as specified.

S&F in repair glass shelf assembly with chromium plated bracket guard and railing 60cm long complete all as specified and directed. Make : Jaquar, Cat Part No ACN-1171N or equivalent of others make as specified.

S&F in repair Vitreous china squatting pan ‘Orissa pattern’ size 580x440mm white with integral foot rest including connection to trap, and flushing pipe, anti-syphonage pipe, etc and including lime concrete bedding complete all as specified and directed.

S&F in repair 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete all as specified and directed.

S&F in repairs kitchen plate rack with and including shelves and hanging arrangement for utensil for kitchen, made of stainless steelsheet 1mm thick of size 24"x24"x10" (ISI marked) complete all as specified and directed.

S&F in repairs PVC water storage tank double layer (ISI marked) white colour cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 25mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ -150) as in roof covering/cladding to wall, fixed with self tapping screws and washers of 68 mm fine thread for MS Pipe purlin and double threaded for wooden purlins as per sutaible distance as guided by AGE/ GE complete all as Specified & directed.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ- 150) as in ridges, hips, valleys/rain water / roof covering/cladding to wall, fixed with self tapping screws and washers of 68 mm fine thread for MS Pipe purlin and double threaded for wooden purlins as per sutaible distance as guided by AGE/ GE complete all as Specified & directed.

S&F mild steel work as in trusses, rafters, purlins etc, and the like made out of MS pipe, flat, angle or hollow sections conforming to Fe-410-W (Gde-E-250) quality-A incl all necessary cleats, gusset plates etc complete all as specified and as directed.

Removal of existing roof treatment i.e. APP Membrane, brick tiling including concrete padding and benching and open up RCC roof slab including picking, sweeping cleaning with wire brush and washing down with water to remove dust, dirt to get surface free of laitance, scales, oil or any other loose material without damaging existing serviceable structure complete to receive new roof treatment including rubbish off the premises upto a distance exc 250 mtr but n.exc 500 mtr complete all as specified and directed. Note applicable for item of roof treatment: The work is required to be carried out at non-accessible roof for double storey. The contractor shall make arrangement of scoffolding , safety & security of workers and arrangement for approach to roof. The rates quoted shall deemed to be included for these iems.

M&L for 10mm thick screed bedding in CM (1:3) mixed with acrylic bonding compound SBR Latex liquid polymer ( As per company instructions ) finished the surface even and smooth without using extra cement complete all as specified and directed. Note : 1. Prpportion of mix and method of mixing of approved liquid water proofer admixture should be applied as per manufacturer's printed instructions. 2. The cost of acrylic bonding compound SBR Latex liquid polymer deemed included in quoted rate.

M&L for water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane as per manufacturer’s instructions with following course of description below :- (a) Applying a priming coat of bituminious primer @ 0.30 Kg /Sqm, till the surface is properly impregnated. (b) Providing APP based 5 layer polymeric membrane minimum weighing 3.6Kg/ Sqm and minimum 3mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms/sqm) centre core, laid on primed surface by forced applications as per the manufacturer's instructions with side over lap of 75 mm and end overlap of 100 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch ) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer (c) Apply two coat of bituminous aluminium paint @ 0.20 Kg/Sqm over APP membrance Note: The work in respect of water proofing treatment shall be carried out only by authorized/approved applicator of the manufacturer/firms of app membrane. The contractor shall submitted 10 year company back warranty before claiming payments complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed

M&L for coloured vitrified tiles of any design and pattern, double charged, 9 to10 mm thick, as in floor etc incl 15 mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B1b with average water absorption between 0.08% to 3%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 4.0% (Max deviation). Centre & Edge curvature and warpage + 0.20% (Max Deviation). Breaking strength 1200 N (Minimum) and minimum 95% tiles shall be free from visible defects and area of each tile of following size complete all as specified and directed :- Note: Shade of the tiles including Colour, design and pattern shall be got approved by GE/ AGE(I).

Area of each tile exc 0.42 sqm but not exc 1.00 sqm.

Description same all as per item No 110 above but as in vertical surface such as dado/ skirting over and including 10mm thick rendering in CM (1:3) to recieve tiles complete all as specified and directed.

S&F in repair aluminium body door closer hydraulically regulated, designation No -3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight 61 to 80 Kg (ISI marked) complete all as specified and as directed.

S&F in repair roller window blinds made up of thermal fabric with roll up blinds mechanism, plain or printed type with all connected fittings and fixtures, of design and shade as approved by GE complete all as specified and directed.

S&F in repairs PVC water storage tank double layer (ISI Marked) cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed

S&F in repair vitreous china WHB of size 560 x 415 x 200mm with full pedastal, white with flat back including CP waste coupling complete all as specified and directed. Make : Jaquar, Cat Part No CNS-WHT-801 (wall hung basin) and CNS-WHT-301 (Full pedestal) or equivalent of others make as specified.

S&F in repair Vitreous china white wash down single piece WC with UF soft close slim seat cover, hinges, dual flush cistern fitting, fixing accessories and accessories set of size 370 x 670 x 720mm with S Trap-300mm complete all as specified and directed. Make : Jaquar, Cat Part No LYS-WHT-38851S300UFMN or equivalent of others make as specified.

S&F in repairs 15mm CP pillar taps cast coper screwed for iron pipe and fixed complete all as specified directed. Make : Jaquar, Cat Part No CON-011KN or equivalent of others make as specified.

S&F in repair 15mm dia brass CP Sink mixer with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete all as specified and directed. Make : Jaquar, Cat Part No CON-319KN or equivalent of others make as specified.

S&F 15mm Brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. Make : Jaquar, Cat Part No CON-167KNB or equivalent of others make as specified.

S&F in repair CP health faucet with 1m flexible tube and wall hook complete all as specified and directed. Make : Jaquar Cat Part No ALD-565 or equivalent of others make as specified.

S&F in repair CP toilet paper holder fixed to wall with CP brass screws complete all as specified and directed. Make : Jaquar, Cat Part No ACN-1151N or equivalent of others make as specified.

Dismantling and taking down carefully U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down carefully sub-main wiring/service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

M&L for point wiring, one light/ fan/ bell/ exhaust fan point controlled by one, one-way Piano type switch 5/6 Ampwith 1.5 sqmm PVC insulated, unsheathed, stranded copper conductor (FRLSH) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of CI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLSH) as earth wire connected with main common earth dolly complete all as specified and directed. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates (ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Descrption same all as per item No. 125 above but one 3pin/ 5pin 5 Amps socket out let on same board controlled by one, one-way piano type switch complete all specified and directed.

Descrption same all as per item No. 125 above but one 3pin/5pin 5 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all specified and directed .

Descrption same all as per item No. 125 above but 2.5 Sqmm PVC insulated cable (FRLSH ) for 15 Amps power point complete all specified and directed.

Descrption same all as per item No. 125 above but 4.0 Sqmm PVC insulated cable (FRLSH ) for 15 Amps power point complete all specified and directed.

S&F switch modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed. Make: Legrand Cat No: 6734 01 or equivalent other make as specified.

S&F modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed. Make: Legrand Cat No: 6734 52 or equivalent other make as specified.

S&F modular switch piano, 1module, flush type button 15/16 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. Make: Legrand cat No: 6734 11 or equivalent other make as specified.

S&F modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed. Make: Legrand Cat No: 6734 55 or equivalent other make as specified.

S&F modular fan regulator electronic, 2module, stepped type, suitable for ceiling fans of any capacity, pre-wired 120/ 280 volts AC 50Hz supply 100Watt complete all as specified and directed. Make: Legrand cat No: 6734 30 or equivalent others make as specified.

S&F modular switch bell push button type, 1module, 6 Amp single pole complete all as specified and as directed. Make : Legrand cat No: 6734 04 or equivalent make as specified.

S&F ceiling rose surface bakelite 65 x 25mm dia three terminals (ISI Marked) complete all as specified and directed. Make – Anchor Jumbo Code-39050 / 3224 or equivalent of make as specified.

S&F bell electric DING DONG type, AC, 230V single pole, 2module complete all as specified and as directed. Make – Legrand cat No: 5734 43 or equivalent make as specified.

S&F angle Lamp holder (with metal ring), insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fitting complete all as specified and as directed. Make– Anchor, Code-39797 or equivalent others make as specified.

S&F LED lamp 9 watt complete all as specified and directed.

S&F in repair LED lights fitting 1X18 watt, 4 ft with extruded aluminium housing heat sink, environmental friendly energy efficient translucent diffuser with LED light source,2400 Lumens( minimum) coefficient colour temp 6000°K to 6500 °K, surge protection range ≥ 2.5KV, voltage protection range-120-300VAC,2 years warranty ,system efficacy not less than140Lm/Watt for the fitting, power factor >.95,total harmonic distortion< 20% color rendering index>80, fixed on site with all accessories including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed.

S&F in repair energy efficient LED lights fitting, 9 watt, 230 Volt, of 600 mm length,CCT 6000ºK to 6500° K , decorative ultra slim linear LED lighting fixture with extruded aluminium housing heat sink, environmental friendly, energy efficient LED light source more than1200 lumens , wall mounted mirror batten, integrated electronic driver, system efficacy not less than 140 lumens /watt CCT 6000 to 6500°K , surge protection range ≥ 2.5 KV , voltage protection range 120-300 volt AC, power factor > 0.95 total harmonic distortion < 20%, colour rendering index > 80, fixed on site with all accessories including 2 years warranty connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed.

S&F single pole and neutral enclosure with a two pole and earth plug socket complete with 01 No, RCCB 25 Amp, 30 mili amps, DP, 240 Volts, AC complete all as specified and directed. Note - Cost of cutting chases for enclosure concealed in wall of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates.

S&F PVC fresh air fan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as specified and directed.

S&F exhaust fan 240 volts Ac 50 Hz 300 mm sweep matellic body (RPM will not be more then 900) including louvers and cutting as required size and shape complete all as specified and directed.

S&Fsheet metal enclosure double door type for MCBs, DB SPN (Single pole and neutral) 240V AC, 8 way with 200 Amps rated bus bar complete all as specified and directed.

S&F MCB SP 5 to 32 Amp 'B' series 10 KA repturing capacity ccomplete all as specified and directed.

S&F MCB SPN 40 Amp 240 V AC 10 KA repturing capacity complete all as specified and directed.

S&F sub main wiring two single core 4 sqmm PVC insulated unsheathed multi stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade surface/ concealed in wall as per existing along with 4.00 Sqmm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and as directed Note:- Two runs of multi stranded copper conductor cable and one run of earth wire including PVC conduit will be measured as a one length.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

UNOQ Private Limied