Supply installation Testing and Commissioning of Lift with a capacity for 08 Persons (544 kg) along with necessary modifications for access through Gr

Name Of Work: Providing & Installation of Lift with a capacity for 08 Passanger (544 kgs) along withh necessary modifications for access through

Ground/First Floor in PEB-I Building at Tulmulla Ganderbal Kashmir

(DSR- Description of Items Unit Qty Rate Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m

2.6 in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as

directed by Engineer-in- charge.

2.6.1 All kinds of soil Cum 11.00 177.50 1952.50

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in

depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

2.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. Cum 1.00 2123.75 2123.75

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived

from natural sources).

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived

from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering,

finishing and reinforcement - All work up to plinth level:

1:1.5:3 ( 1 cement:1.5 coarse sand Zone-III derived from natural sources :3graded stone aggregate 20mm nominal size derived

from natural sources.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering,

shuttering, finishing and reinforcement.

1 cement:1.5 coarse sand (Zone-III) derived from natural sources:3 graded stone aggregate 20mm nominal size derived from

natural sources

5.9 Centering and shuttering including strutting, propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete Sqm 20.00 392.15 7843.00

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 8.00 736.40 5891.20

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Strut Sqm 15.00 961.30 14419.50

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above

5.22A.3 Cold twisted bars Kg 80.00 107.85 8628.00

Digitally signed by Om Prakash

(DSR- Description of Items Unit Qty Rate Amount

6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum Cum 2.00 7132.25 14264.50

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a

grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1

white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of

cramps, which shall be paid for separately).

8.1.1.2 Area of slab over 0.50 sqm Sqm 2.00 5938.00 11876.00

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high

gloss finish etc. complete as per design approved by Engineer-in-Charge.

8.3.1 Marble work Metre 8.00 298.60 2388.80

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with

open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required,

proper drainage of water to make it watertight including checking of all the structural and functional design.

(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour

of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core

sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil

coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and

polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone

sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and

serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon

separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost

of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in

an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and

protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base

frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with

aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings,

as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for

the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding

(including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS

9.84 : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed Each 6.00 983.15 5898.90

adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or shade, with necessary screws etc. complete :

Digitally signed by Om Prakash

(DSR- Description of Items Unit Qty Rate Amount

Providing and fixing panelling or paneling and glazing in panelled or panelled and glazed shutters for doors, windows and

clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebated to be measured). Panelling for

panelled and glazed shutters 25mm to 40mm thick: Pre-laminated with decorative lamination on both side exterior Grade - I MDF

Board 12 mm thick confirming to IS:14587

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in

position and applying a priming coat of approved steel primer all complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption

less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick

cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only

Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for

placing the tiles gently and easily.

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power

pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of

angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed

to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230

mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5

x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-

nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint

and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings

for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with

12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board Sqm 20.00 1529.10 30582.00

Digitally signed by Om Prakash

(DSR- Description of Items Unit Qty Rate Amount

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer in

charge) .50 mm (-0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade. 5-7

microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25

12.50 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 mtr or as desired bt Sqm 18.00 738.65 13295.70

Engineer in charge. The sheet shall be fixed using self-drilling /self-tapping screws of size (5.5 X55 mm) with EPDM seal.

complete upto any pitch in horizontal /vertical or curved surfaces excluding the cost of purlins rafters and trusses and including

cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating

12.51 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top

coat 15-18 microns using self drilling/ self tapping screws complete

12.51.6 Gutter (600 mm over all girth Mtr 10.00 1313.70 13137.00

13.1 12 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

13.43.1 Water thinnable cement primer Sqm 18.00 185.65 3341.70

13.50 Applying priming coat:

13.50.2 With ready mixed aluminium primer of approved brand and manufacture on resinous wood & plywood Sqm 18.00 74.65 1343.70

13.62 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

13.62.1 Two or more coats on new work Sqm 48.00 226.25 10860.00

15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 26.00 73.40 1908.40

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal

of unserviceable materials within 50 metres lead.

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by

mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15.44.1 15 mm to 40 mm nominal bore Metre 20.00 149.80 2996.00

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable

material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Digitally signed by Om Prakash

(DSR- Description of Items Unit Qty Rate Amount

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular

sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required

21.1 EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically

wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid

for separately) :

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Kg 50.00 530.90 26545.00

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of

fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Kg 50.00 634.45 31722.50

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to

21.2 IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless

steel screws etc. complete as per architectural drawings and directions of engineer- in-charge

21.2.2 Pre-laminated particle board with decorative lamination on both sides Sqm 17.00 1115.40 18961.80

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene

21.3 gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading

shall be paid in basic item):

21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) Sqm 20.00 1505.25 30105.00

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having

brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of

cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates

with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

21.4.1 With stainless steel cover plate minimum 1.25 mm thicknes Each 8.00 2823.85 22590.80

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer

rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

21.8.1 Upto 5mm depth and 5 mm width Metre 25.00 96.75 2418.75

Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic

coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved

make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for

Digitally signed by Om Prakash

(DSR- Description of Items Unit Qty Rate Amount

Supply, Installation, Testing and Commissioning of ElectricTraction Passenger Elevator with capacity 544 Kg, 8 persons speed

1m/sec, stopped at all floor,Access type frontal,Stops G+1,Sliding doors.Independent electric cabin,extraordinary safety systems

are implemented.Seperate overspeed governor and brake systems, hand rail for stability and advanced door safety mechanisms with

light rays and pessure sensors.TFTcolour display with landing indicator,voice annunciator and floor arrival chime,telephonic

communication,led spot lights in the ceiling,illuminating buttons,continous comprehensive log with advanced error code

notification system,hand rails, complete as per specifications and instruction of Engineer in charge.The work also include all

supporting arrangement system, necessary scaffolding required for erection of the complete system, necessary wiring and

installation of lighting for lift well and lift pit, providing ladder in the lift pit etc. as required complete. (Refer

Digitally signed by Om Prakash