RRP-2 02024-25neyyattinkara 3928- PUTHIYA MARAKYAMUTTOM CHETTUKUZHI RAMAPADHNI ROAD MUNICIPALITY THIRUVANANTHAPURAM-General Civil Work

3.2:Preparation of Foundation for Embankment Scarifying Existing Bituminous Surface to a Depth of 150 mm by Mechanical Means Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

4.9:Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. By Mechanical Means with 1 km lead

75.5.1.1pb:Prime Coat - Low porosity - With Packed Bitumen Rates Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

75.5.2.3pb:Tack Coat - With Packed Bitumen Rates Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.5.B.2pb:Modified Penetration Macadam 75 mm thick using Bitumen S-65 - Packed Bitumen Rates Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.

75.5.2.1pb:Tack Coat - With Packed Bitumen Rates Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.11.1.A.2pb:Mix Seal Surfacing - Manual Means - Type A - Bitumen S-65 - Packed Bitumen Rates Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509 By Manual Means Type A (II) Bitumen (S-65)

OD137113/2025-2026:PROVIDING AND FIXING OF DIRECTION AND PLACE IDENTIFICATION RETRO REFLECORISED SIGN WITH 7 YEARS WARRANTY MANUFACTURED AS PER IRC : 67 MADE OF TYPE IV MICRO PRISMATIC GRADE SHEET FIXED OVER ALUMINIUM SHEETING 2 MM THICK /ALUMINIUM COMPOSITE MATERIAL SHEETING 4 MM THICK WITH AREA NOT EXCEEDING 0.9 SQM,WITH SUITABLE BACK SUPPORTING FRAME OF MS ANGLE 40X40X6 ANDSUPPORTED ON GI PIPE POLE 50 MMNB-2NOS CONFIRMIG TO IS 1239 FIRMLY FIXED TO THE GROUND BY MEANS OF PROPERLY DESIGNEDFOUNDATION WITH M15 GRADE CEMENT CONCRETE MIN SIZE 40CMX40X60CM,60CMBELOW GROUND LEVEL INCLUDING PAINTING ALL EXPOSED SURFACE WITH 2 COATS OF EPOXY PAINTING OVER EPOXY PRIMER AND AS PER APPROVED AND CLAUSE 801 INCLUDING LETTERING SYMBOLS ETC.(DERIVED MORD SPEC10.3.A.2)