Setting up of 2 ICUs 5-Bedded Each Total 10 Bedded Including Supply, Installation, Commissioning and Maintenance of Equipment and Related Services Including Minor Works at District Hospital Haridwar and Sub District Hospital Roorke

Amount

ESSENTIAL EQUIPMENT

Infusion Pump

Syringe Pump

Pulse oximeter

Multipara Bedside Monitors (Invasive)

High End Ventilator

Ultrasound with ECHO (ICU, Neuro ICU)

4D Probe with 1-8 MHz for Ultrasound with ECHO

Cardiac Probe with 1-4 MHz Ultrasound with ECHO

ABG Machine

Intubating video scope

Central Monitoring System

CO, SVR, ScvO2 Monitor

12 Lead ECG

ETO Sterilizer

Autoclave Electrical 95L

Holter Machine

Generator 125 KV

Online UPS - 40 KVA

CRITICAL CARE EQUIPMENT

Fiberoptic bronchoscope

I A Baloon Pump

CPR Machine

GENERAL EQUIPMENT

Over bed table

Dressing Tray

Crash Cart

Foot Operated Suction Machine

Refrigerator

Air Beds

All in computer & Printer

Glucometer

Biomedical Waste Bins

Spinal board

Rigid Cervical Spine Collar

Resusitation Kit/Cart

Automatic shoe cover machine

Pump, suction, portable, 220V, w/access.

Laryngoscope set - All blades

Stretcher (Hydraulic)

Spinal board

Rigid Cervical Spine Collar

Manual BP Apparatus

Stethoscope

Office Tables

Office Chairs

Revolving Chairs

Beds for doctor & staff

Almerah

Locker Almerah

Nebulizer

Wheel Chair

Intermittent compression device for DVT prophylaxis

Description of Work / Item(s)

Amount

Oxygen Manifold Cylinder Oxygen Manifold would be suitable to withstand a pressure of 140 Kg/Cm2and above along with high pressure copper annealed tail pipes with end Brass adapter suitable for Oxygen Cylinders and manifold. Top frame comprising of high pressure copper pipes of size 12mm I.D x 1.5mm wall thick, with high pressure brass fittings made of high tensile brass and connections through non-return values; high pressure copper tail pipes, made of high pressure copper pipe of size 7mm I.D x 1.5mm wall thick. The design of middle and bottom frames would be provided to fit both round and flat bottom cylinders safely. The manifold would be tested (hydraulically) at 3500 pig 4+4 Oxygen Manifold , High Pressure Tail Pipe with NRV

Fully Automatic Oxygen Control Panel Air Compressor of Capacity 5HP Type : Reciprocating, Air cooled Capacity : 15.5 cfm 439 lpm No. of Cylinders : 2 Nos. in each Air Compressor Drive : Belt driven No. of Air Compressors : 1 Nos. Motor Capacity : 5 HP Receiver type : Vertical type with inlet, outlet & drain provisions

Receiver Capacity : 750 litres water capacity

Electric Motor 5HP /3.7 Kw

Dryer

Air Drier Type : Heatless Desiccant Type Air Drier Capacity : 15 cfm No. of Air driers : 1 No.

Pressure Gauge

Cut of Valve

Air Filter

Air Pressire Switch

slincer

Vacuum Base Unit (5HP) Type : Reciprocating, Air-cooled Capacity : 60cfm, 1699 lpm No. of Cylinders : 2 Nos. in each vacuum pump Drive : Belt driven No. of Vacuum pumps : 1 Nos. Motor Capacity : 5 HP, kw 3.7 Receiver Capacity : 750 liters water capacity vertical

Electric Motor 5HP / 3.7KW

Vacuum Tank 750ltr

Non - Return Valve

Vacuum Switch

Vacuum Gauge

Isolation Valve

Vacuum Filter

Inter-Connecting Pipeline 42mm

Vacuum Bactria Filter A bacterial filter would be fitted between each pump and the reservoir, which have replaceable elements and 6 each shall be capable of passing the tatal design flow. The filters would be arranged such tht one filter can be taken out for servicing without interrupting or restricting the vacuum servie as a whole. The filters would have a penetration not exceeding 0.05% when tested by the sodium flames test in accordance with BS 3928. Moisture traps would also be fitted on each leg. These may be cobined with the filter units. The traps would have removable transparent drain bowls which can be removed without affecting plan operation. The bowls would be serializable by using moist stream at 2.2 bar and 138 degree celsius in porous load sterilizer.

Copper Piping & Fitting : All copper pipes would be Solid drawn, seamless, deoxidized, non-arsenical, half hard, tempered and degreased materials conforming to BS:EN :13348:2001 + A1:2005 Pipes sizes would be used as under: Copper Fittings: Fittings would be made of copper and suitable for a stem of working pressure of 17 bar and would confirm to BS 864 with specially made for brazed socket type connections. 15mmX0.9mm

Copper Piping & Fitting : All copper pipes would be Solid drawn, seamless, deoxidized, non-arsenical, half hard, tempered and degreased materials conforming to BS:EN :13348:2001 + A1:2005 Pipes sizes would be used as under: Copper Fittings: Fittings would be made of copper and suitable for a stem of working pressure of 17 bar and would confirm to BS 864 with specially made for brazed socket type connections. 22mmX0.9mm

Copper Piping & Fitting : All copper pipes would be Solid drawn, seamless, deoxidized, non-arsenical, half hard, tempered and degreased materials conforming to BS:EN :13348:2001 + A1:2005 Pipes sizes would be used as under: Copper Fittings: Fittings would be made of copper and suitable for a stem of working pressure of 17 bar and would confirm to BS 864 with specially made for brazed socket type connections. 42mmX1.2mm

GAS OUTLET POINTS with Probe Would have terminated properly Double locking Front Loaded which have a parking facility which also avoids interchanging of outlets and keys including all accessories .(Fully Metal Outlet)) Oxygen

GAS OUTLET POINTS with Probe Would have terminated properly Double locking Front Loaded which have a parking facility which also avoids interchanging of outlets and keys including all accessories .(Fully Metal Outlet)) Med Air4 bar

GAS OUTLET POINTS with Probe Would have terminated properly Double locking Front Loaded which have a parking facility which also avoids interchanging of outlets and keys including all accessories .(Fully Metal Outlet)) Vacuum

BPC Oxygen Flow meter with Humidifier Bottle: • Flow meter would be Backpressure Compensated. • Flow meter would be accurate gas flow measurement and control within a range of 0-15 litres per minute. • It would meet strict precision and durability standards. • Flow meter body would be made of brass material. • Flow tube and shroud components would be made of clear, impact resistant polycarbonate. • The humidifier bottle would be unbreakable polycarbonate material and autoclavable at 134 degrees centigrade. The humidifier would have built in safety valve.

Single piece wall mounted suction collection & regulation unit With jar capacity of 600ml each shall be provided at each of the bed side. Jars are would be made of autoclavable materials. The units shall be clamped to the wall using suitable clamps.

ISOLATION VALVES: LEAK CLASS Would be 900 turn, ball valves of brass body, duly chrome plated on the outer periphery, SS ball with high quality Teflon seated, connected to pipeline with brass ferrule for easy maintenance. ID of the copper pipe and the ball valve would have same dimensions to avoid the flow friction 15mm

ISOLATION VALVES: LEAK CLASS Would be 900 turn, ball valves of brass body, duly chrome plated on the outer periphery, SS ball with high quality Teflon seated, connected to pipeline with brass ferrule for easy maintenance. ID of the copper pipe and the ball valve would have same dimensions to avoid the flow friction 22mm

ISOLATION VALVES: LEAK CLASS Would be 900 turn, ball valves of brass body, duly chrome plated on the outer periphery, SS ball with high quality Teflon seated, connected to pipeline with brass ferrule for easy maintenance. ID of the copper pipe and the ball valve would have same dimensions to avoid the flow friction 42mm

Area Alarm Area Gas alarm panel Six Lines, Would audio- visual alarms for each gas used on the floor and come fitted with test and mute button. Running on electricity 220V, these units are suggested to be fitted on each floor as well as areas of heavy usage. It would be fitted with a pressure gauge. It indicates low, medium & high pressure sensors. (Digital) Area Alarm for Five ( 2Gas + 01 Vacuum) Services

Bed Headed Panel . ( Running) – 04Feet Long Aluminium Die Pressed Bed head panels Would have bellow Accessories 1. IV Stand. 2. Monitor stand wall mounted. 3. Ward vacuum unit clip. 4. Provision Gas/Vacuum outlets as follows:- ü One oxygen outlet. ü One Vacuum outlet. ü One Compressed Air outlet 4 Bar.

Oxygen Manifold Cylinder Oxygen Manifold would be suitable to withstand a pressure of 140 Kg/Cm2and above along with high pressure copper annealed tail pipes with end Brass adapter suitable for Oxygen Cylinders and manifold. Top frame comprising of high pressure copper pipes of size 12mm I.D x 1.5mm wall thick, with high pressure brass fittings made of high tensile brass and connections through non-return values; high pressure copper tail pipes, made of high pressure copper pipe of size 7mm I.D x 1.5mm wall thick. The design of middle and bottom frames would be provided to fit both round and flat bottom cylinders safely. The manifold would be tested (hydraulically) at 3500 pig 4+4 Oxygen Manifold , High Pressure Tail Pipe with NRV

Fully Automatic Oxygen Control Panel The fully automatic control panel would be the following features: • Would be enclosed in a metal cabinet with a hinged cover. The side covers of the panel would be made of fiber glass. • Panel cover would be fitted with a lock to prevent unauthorized access can be swung open for maintenance. • Would be Fully Automatic Changeover operation and no manual action • The service gas would pneumatically operate gas change over system. • Delivery of gas through control panel would not be dependent on electricity. • Would be capable of delivering very high flow rate not less than 1300 litres per minute at delivery pressure. • Would have Visual indication of the • state of the manifold by 3 gauges within the control panel, which would be clearly visible through the transparent cover. • Would have Audio – visual alarm indication for changeover of empty cylinder bank to filled cylinder bank. • Built in transformer to ensure safe operation by low voltage. Microprocessor based alarm signal control with high ‘db’ Siren system.

Compressed Air Base Unit Air Compressor of Capacity 5HP Type : Reciprocating, Air cooled Capacity : 15.5 cfm 439 lpm No. of Cylinders : 2 Nos. in each Air Compressor Drive : Belt driven No. of Air Compressors : 1 Nos. Motor Capacity : 5 HP Receiver type : Vertical type with inlet, outlet & drain provisions

Receiver Capacity : 750 litres water capacity

Electric Motor 5HP /3.7 Kw

Dryer

Air Drier Type : Heatless Desiccant Type Air Drier Capacity : 15 cfm No. of Air driers : 1 No.

Pressure Gauge

Cut of Valve

Air Filter

Air Pressire Switch

Vacuum Base Unit (5HP) Type : Reciprocating, Air-cooled Capacity : 60cfm, 1699 lpm No. of Cylinders : 2 Nos. in each vacuum pump Drive : Belt driven No. of Vacuum pumps : 1 Nos. Motor Capacity : 5 HP, kw 3.7 Receiver Capacity : 750 liters water capacity vertical

Electric Motor 5HP / 3.7KW

Vacuum Tank 750ltr

Non - Return Valve

Vacuum Switch

Vacuum Gauge

Isolation Valve

Vacuum Filter

Inter-Connecting Pipeline 42mm

Vacuum Bactria Filter A bacterial filter would be fitted between each pump and the reservoir, which have replaceable elements and 6 each shall be capable of passing the tatal design flow. The filters would be arranged such tht one filter can be taken out for servicing without interrupting or restricting the vacuum servie as a whole. The filters would have a penetration not exceeding 0.05% when tested by the sodium flames test in accordance with BS 3928. Moisture traps would also be fitted on each leg. These may be cobined with the filter units. The traps would have removable transparent drain bowls which can be removed without affecting plan operation. The bowls would be serializable by using moist stream at 2.2 bar and 138 degree celsius in porous load sterilizer.

Copper Piping & Fitting : All copper pipes would be Solid drawn, seamless, deoxidized, non-arsenical, half hard, tempered and degreased materials conforming to BS:EN :13348:2001 + A1:2005 Pipes sizes would be used as under: Copper Fittings: Fittings would be made of copper and suitable for a stem of working pressure of 17 bar and would confirm to BS 864 with specially made for brazed socket type connections. 15mmX0.9mm

Copper Piping & Fitting : All copper pipes would be Solid drawn, seamless, deoxidized, non-arsenical, half hard, tempered and degreased materials conforming to BS:EN :13348:2001 + A1:2005 Pipes sizes would be used as under: Copper Fittings: Fittings would be made of copper and suitable for a stem of working pressure of 17 bar and would confirm to BS 864 with specially made for brazed socket type connections. 22mmX0.9mm

Copper Piping & Fitting : All copper pipes would be Solid drawn, seamless, deoxidized, non-arsenical, half hard, tempered and degreased materials conforming to BS:EN :13348:2001 + A1:2005 Pipes sizes would be used as under: Copper Fittings: Fittings would be made of copper and suitable for a stem of working pressure of 17 bar and would confirm to BS 864 with specially made for brazed socket type connections. 28mmX1.2mm

Copper Piping & Fitting : All copper pipes would be Solid drawn, seamless, deoxidized, non-arsenical, half hard, tempered and degreased materials conforming to BS:EN :13348:2001 + A1:2005 Pipes sizes would be used as under: Copper Fittings: Fittings would be made of copper and suitable for a stem of working pressure of 17 bar and would confirm to BS 864 with specially made for brazed socket type connections. 42mmX1.2mm

GAS OUTLET POINTS with Probe Would have terminated properly Double locking Front Loaded which have a parking facility which also avoids interchanging of outlets and keys including all accessories .(Fully Metal Outlet)) Oxygen

GAS OUTLET POINTS with Probe Would have terminated properly Double locking Front Loaded which have a parking facility which also avoids interchanging of outlets and keys including all accessories .(Fully Metal Outlet)) Med Air4 bar

GAS OUTLET POINTS with Probe Would have terminated properly Double locking Front Loaded which have a parking facility which also avoids interchanging of outlets and keys including all accessories .(Fully Metal Outlet) Vacuum

BPC Oxygen Flow meter with Humidifier Bottle: • Flow meter would be Backpressure Compensated. • Flow meter would be accurate gas flow measurement and control within a range of 0-15 litres per minute. • It would meet strict precision and durability standards. • Flow meter body would be made of brass material. • Flow tube and shroud components would be made of clear, impact resistant polycarbonate. • The humidifier bottle would be unbreakable polycarbonate material and autoclavable at 134 degrees centigrade. The humidifier would have built in safety valve.

Single piece wall mounted suction collection & regulation unit With jar capacity of 600ml each shall be provided at each of the bed side. Jars are would be made of autoclavable materials. The units shall be clamped to the wall using suitable clamps.

ISOLATION VALVES: LEAK CLASS Would be 900 turn, ball valves of brass body, duly chrome plated on the outer periphery, SS ball with high quality Teflon seated, connected to pipeline with brass ferrule for easy maintenance. ID of the copper pipe and the ball valve would have same dimensions to avoid the flow friction 15mm

ISOLATION VALVES: LEAK CLASS Would be 900 turn, ball valves of brass body, duly chrome plated on the outer periphery, SS ball with high quality Teflon seated, connected to pipeline with brass ferrule for easy maintenance. ID of the copper pipe and the ball valve would have same dimensions to avoid the flow friction 22mm

ISOLATION VALVES: LEAK CLASS Would be 900 turn, ball valves of brass body, duly chrome plated on the outer periphery, SS ball with high quality Teflon seated, connected to pipeline with brass ferrule for easy maintenance. ID of the copper pipe and the ball valve would have same dimensions to avoid the flow friction 42mm

Area Alarm Area Gas alarm panel Six Lines, Would audio- visual alarms for each gas used on the floor and come fitted with test and mute button. Running on electricity 220V, these units are suggested to be fitted on each floor as well as areas of heavy usage. It would be fitted with a pressure gauge. It indicates low, medium & high pressure sensors. (Digital) Area Alarm for Five ( 2Gas + 01 Vacuum) Services

Bed Headed Panel . ( Running) – 04Feet Long Aluminium Die Pressed Bed head panels Would have bellow Accessories 1. IV Stand. 2. Monitor stand wall mounted. 3. Ward vacuum unit clip. 4. Provision Gas/Vacuum outlets as follows:- ü One oxygen outlet. ü One Vacuum outlet. ü One Compressed Air outlet 4 Bar.

Air Dryer Working Pressure 15kg/cm2 Dew Point : 40 Degree

Civil Work (Basement and Compressor room with roof) (10' Length X 6' Breath x 8' Height)

Electrical work (IDB, MCB, anf 3 phase incomer Wiring for Compressor)r.

Description of Work / Item(s)

Amount

Civil Work

Civil Work

Description of Work / Item(s)

Amount

Electrical Work

Electrical Work

Description of Work / Item(s)

Amount

Infusion Pump

2nd Year

3rd Year

4th Year

5th Year

6th Year

Syringe Pump

2nd Year

3rd Year

4th Year

5th Year

6th Year

Pulse oximeter

2nd Year

3rd Year

4th Year

5th Year

6th Year

Multipara Bedside Monitors (Invasive)

2nd Year

3rd Year

4th Year

5th Year

6th Year

High End Ventilator

2nd Year

3rd Year

4th Year

5th Year

6th Year

Ultrasound with ECHO (ICU, Neuro ICU)

2nd Year

3rd Year

4th Year

5th Year

6th Year

ABG Machine

2nd Year

3rd Year

4th Year

5th Year

6th Year

Intubating video scope

2nd Year

3rd Year

4th Year

5th Year

6th Year

Central Monitoring System

2nd Year

3rd Year

4th Year

5th Year

6th Year

CO, SVR, ScvO2 Monitor

2nd Year

3rd Year

4th Year

5th Year

6th Year

12 Lead ECG

2nd Year

3rd Year

4th Year

5th Year

6th Year

ETO Sterilizer

2nd Year

3rd Year

4th Year

5th Year

6th Year

Autoclave Electrical 95L

2nd Year

3rd Year

4th Year

5th Year

6th Year

Holter Machine

2nd Year

3rd Year

4th Year

5th Year

6th Year

Generator 125 KV

2nd Year

3rd Year

4th Year

5th Year

6th Year

Online UPS - 40 KVA

2nd Year

3rd Year

4th Year

5th Year

6th Year

Fiberoptic bronchoscope

2nd Year

3rd Year

4th Year

5th Year

6th Year

I A Baloon Pump

2nd Year

3rd Year

4th Year

5th Year

6th Year

2nd Year

3rd Year

4th Year

5th Year

6th Year

CPR Machine

2nd Year

3rd Year

4th Year

5th Year

6th Year

2nd Year

3rd Year

4th Year

5th Year

6th Year