RM of 5 No. Tube well in Indora Constituency in tehsil Indora Distt. Kangra

Supply of submersible pumping set of Kirloskar/Kilburn/Clama/Crompton/KSB make conforming to BIS; 8034-1976 latest suitable for lifting clean water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacturer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:-

i) Total Head 102.16 Mtrs

ii ) Discharge required from each pump. 18.40 LPS

iii) No. of pump required 1.00 Nos.

iv) Location of the site of installation of machinery. The site is located at a distance of 10 KM from Kandrori Railway Station by road & 0.100 KM on head load(for the installation of machineries.

v) The Altitude of installation. The altitude of place is 310.00 mtrs. Above MSL

vi) Type of current. AC Three phase supply with

vii) Rate Voltage 415+ 10%

viii) Type of water and its source Tubewell No 24 (Nadoun)

ix) Charactristics of water. -

a)Ambient Temperature dig.c 20 dig. C

b)Turbidity NTU 113NTU

c)Hardness260Mg/Ltrs(as CaCO3) 540 Mg/ltr

d) PH 6.5 to 8.5

e) TDS 540 PPM

f)Other -

x) Depth ofTUbe Well

xi) LWL in Tube Well 267 mtr

xii) Center line level of Pump shaft 268 mtrs.

xiii) Discharge level of highest point 357 mtrs.

xiv) Total head in Mtrs 102.16 mtrs.

xv) Length of R/Main 565 mtrs.

xvi) Dia of Rising main 150 mm dia GI pipe 4.80 mm thick

xvii) No of working hours per day 20 Hours

xviii) Limit of pump operation. (-) 15 % (+) 10% of total head

xix) R.P.M. of pumping set. 2900 RPM

xx) Test run. 8 Hours continueously for 7 days

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 1 No. pump of rating 45HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Reputed make.

Providing and fixing of Kirloskar/Leader make Cast iron double flanged swing check type reflux valve of class PN 1.0 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 10.20 Kg/Cm2 confirming to BIS 5312-1984 Part-II .(The size & class of valve shall be specified by the tenderer)150 mm dia

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

On supply side of 3½ core coper cable 25 mm^2 ( From HPSEB Meter to Switch & Starter).

On motor side 3 core flat joint less copper cable of size 16 mm^2 ( From Switch & Starter to Motor) pump installed in the bore

Supply of standarad make 150mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

Please Enable Macros to View BoQ information