REPAIR REPLACEMENT OF ROOF SHEETING JOINERY AND CERTAIN MISC WORK TO MES INSTALLATION AT ZONE A AND B UNDER GE 862 EWS AT RAJOURI

Amount

S&F of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl dismantling of old sheet of any description, complete all as specified and as directed.

S& F of Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl dismantling of old sheet of any description, complete all as specified and as directed.

Dismantling of structural steel work of any description complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade ST-240, complete all as specified and directed.

M&L for 75mm thick cement concrete type D-2 1:4:8 (using 40 mm graded stone graded stone aggregate) as in sub base for tiling, complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 450 x 350 x 7mm thick, (premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:3, after dismantling old unserviceable of tiles, complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar 1:4, after dismantling old unserviceable of tiles, complete all as specified and as directed.

M&L for Machine cut kota stone slab(mirror polished) flooring 18-20mm thick as in floors and jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including screed bed or bedding layer of 15 mm thick in cement mortar 1:4 of any size after dismantling old unserviceable of kota stone, complete all as specified and directed.

M&L for Machine cut kota stone slab(mirror polished) 18-20mm thick as in skirting and jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including rendering of 20 mm thick in cement mortar 1:4, after dismantling old unserviceable of skirting, complete all as specified and directed.

Demolition of brick work or stone / boulder or concrete block masonry including all quoins, arches, pillars, etc. built in cement mortar, complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

All as per item No 11 but except bricks, complete all as specified and directed. Note: brick retrieved from item No 10 will be re-used.

M&L for stone walling of random rubble, uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

All as per item No 14 but except stones, complete all as specified and directed. Note: stone retrieved from item No 10 will be re-used.

Extra over stone walling for hammer dressing to face stone and dressing of face beds with maximum depression on face from straight edge held against the dressed surface on sand stone n.exc 20mm, complete all as specified and directed.

Taking down cement or cement lime plaster any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M & L for Rendering 15 mm thick on fair faces of brick work or concrete surface in CM (1:6), finished even and smooth without using extra cement and chicken mesh shall be used as per the site requirement and directed by the Engr-in-Charge to prevent cracks and complete all as specified and directed. Note:- Cost of chicken mesh is included in the quoted rate.

M & L for Rendering 15 mm thick on fair faces of brick work or concrete surface in two layers (5mm thick CM 1:4 over 10mm thick CM 1:6 ) on external brick work or concrete surfaces , finished even and smooth without using extra cement including mixing with liquid WPC all as per manufacturers instructions complete all as specified and as directed. Note:- Chiken mesh shall be fixed (Cost of WPC will be included in the qoted rate).

M & L for rendering 10mm thick in cement mortar (1:3) on soffits of slabs, chajja etc finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 20 mm thick on stone walls other than fair faces in CM (1:6), finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plastered wall surface including cornices etc and applying two coats of Premium acrylic Alkali & fungal & dirt resistance exterior emulsion all weather proof paint of Apex Ultima of ASIAN or equivelent make of any approved single/two or more colour pattern as specifed by GE over and including a coat of primer, complete all as specified and directed. Note :- Buildings height not exceeding four storey and rate shall be included for necessary scaffolding and safety measures where required at site).

M & L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whitening, complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying two coats of distemper oil emulsion over one coat of chalk whitening, complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 but not exceeding 4.0 sqm each, complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down shutters of any description exceeding 1.0 but not exceeding 2.0 sqm each, complete all as specified and directed.

S & F of 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates and holdfast & PCC filling etc, complete all as specified and directed.

All as per item No 28 above but frame size of 105x60mm, complete all as specified and directed.

M&L for 2nd class hard wood well seasoned plain solid straight chowkhat framed wrought framed, rebated on the solid, round or chamfered put together with glue and pinned at joint and fixed in wall, complete all as specified and directed.

S & F for 35mm thick 2nd plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S & F of 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, part – I (Specifications) , complete all as specified and directed.

M & L for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specifications, complete all as specified and directed.

M & L for factory made solid PVC panel door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheety strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded.sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing, complete all as specified and directed.

S & F of box type steel window with side hung shutters including box type hinges with steel handle, hold fast and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

All as per item No 35 above but without glazing bars, complete all as specified.

S&F steel ventilators with top hung shutters including hinges and handle with steel peg stay complete welded, complete all as specified and directed.

M & L figured glass, pin head type, 3mm thick and glazing with oil putty in squares n.exc. 0.5 sqm each pane, complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe-290 Grade E-165 including dismantling old one, complete all as specified and directed.

S & F Stainless steel wire cloth., 0.71 mm nominal dia of size of mesh 12 mm and fixed with tinned tacks, or stainless steel wire staples, complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description from wooden or steel frames glazed with putty/beads, complete all as specified and directed.

S & F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty/wooden beads in square in any size, complete all as specified and directed.

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled, complete all as specified and directed.

S & F of 150 mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

S & F of 125 mm long extruded anodised aluminium alloy handle, fabricated type, complete all as specified and directed.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy, complete all as specified and directed.

M & L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S & F in repair for rotational moulded poly-ethylene water storage tanks of 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of existing 500ltr capacity tank, complete all as specified and directed.

S & F in repair for rotational moulded poly-ethylene water storage tanks of 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of existing 1000ltr capacity tank, complete all as specified and directed.

M & L in repairs for 15 mm dia Fancy type Chromium plated Angle valves, cast copper alloy screwed down high pressure, with crutch or butterfl y handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in PVC waste pipe 600/900mm long suitable for Wash hand basins and urinals including connecting, complete all as specified and directed.

S & F in repairs brass chromium plated tubular towel rail 20mm dia 600mm long with and including one pair of brass chromium plated brackek, complete all as specified and directed.

S & F in repairs for 125mm dia PTMT grating doom with waste hole for waste pipe ( minimum weight 40 gram), complete all as specified and directed.

S & F in repair for PVC connection pipe 15mm dia with PTMT nuts of length 450mm, complete all as specified and directed.

S &F in repairs for 15 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe orr brass errule and fixed, complete all as specified and directed.

S &F in repairs for 20 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe orr brass errule and fixed, complete all as specified and directed.

Supply and fix in repairs vitreous china squatting pan, orissa pattern size 680 x 470 mm white/colour with integral foot rest (excluding flushing cistern and flush pipe) including provison of lime concrete, complete all as specified and directed.

S & F in repairs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve foat and handle including brackets 10 litres, complete all as specified and directed.

Supply and fixing in repairs viterous China wash basin, white flat back, size 550x400mm excluding taps, waste chain and plug and porcelan stopper but including brackets, complete all as specified and directed.

S & F in repair 15mm dia CP Pillar Cock, complete all as specified and directed.

S&F in repair 15 mm dia bib tap cast copper alloy, chromium plated ,'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, complete all as specified and directed.

S & F in repairs for PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenchesor in floors 110 mm dia, complete all as specified and directed.

S & F in repairs PVC (SWR) bends of any radius of 110mm dia, complete all as specified and directed.

S & F in repairs for PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenchesor in floors 75 mm dia, complete all as specified and directed.

S & F in repairs PVC (SWR) bends of any radius of 75mm dia, complete all as specified and directed.

M & L for 75 mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in complete, all as specified and directed.

M&L for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions , laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm center to center from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per instructions including dismantling of existing board with cover fillets etc, complete all as specified and directed.

Demolition of reinforced cement concrete in any description or ground floor and paving not exc 15cm thick, complete all as specified and as directed.

M & L for TMT bars 8 mm dia and over, cut to length, bent to shape required, incvluding cranking, binding spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M & L for use and waste of form work to soffits of flat suspended slabs such as roof slabs, floor slabs,chajjas, landings and similar work not exc. 200 mm thick horizontal or slopping in rough finished surface of concrete, complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, chajjas, shelves and the like, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as specified and directed.

M & L for 100 mm th Cement concrete type B1 1:2:4 (20 mm graded aggregate) in floors, finishing cement concrete surface even and smooth using extra cement, complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:3:6 type C-2, using 40 mm graded stone aggregate as in plinth protection laid to slop of 1:12, or in floors finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight), complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description having width/girth exceeding 10 cm and apply one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description having exceeding 10 cm width/girth and apply one coat of synthetic enamel paint, complete all as specified and directed.

M & L for applying one coat of distemper oil emulsion on old wall surfaces including preparation of surfaces, complete all as specified and directed.

Description all as per item No 78 above but on ceiling, complete all as specified and directed.

M&L for complete removal of existing treatment on wall/roof surface including cornices and chajjas etc and applying two coats of exterior emulsion weather coat paint of Apex Ultima of ASIAN or equivelent make of any approved single/two or more colour pattern as specifed by GE over and including a coat of primer, complete all as specified and directed.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 15 mm dia, complete all as specified and directed.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia, complete all as specified and directed.

M & L for steel water tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors 15 mm bore including takingdown old steel tubing, complete all as specified and directed.

M & L for steel water tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors 20 mm bore including takingdown old steel tubing, complete all as specified and directed.

S&F in repairs vitreous china urinals,flat back of size 465mmX355mmX265mm,white, bowl type, complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe with grating and union for discharge pipe including connecting to waste pipe, complete all as specified and directed.

Complete removal of existing water proofing treatment over RCC roof, projections of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with wire brush including removing debris from the site and depositing in low lying area where directed and providing following :- (a) Rendering 10mm thick in cement mortar 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound @ 2% by weight of cement. (b) Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried. (c) After the primed surface has dried, apply a coat of hot blown bitumen(85/25 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of the surface. (d) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application method, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric water proofing membrane should be five layered with centre core as 90 micron high molecular high density polyethylene film, min weight 3 Kg per sqm & minimum 3mm thick reinforced with polyster non wove fabric, APP membrane shall laid acorss the slop from lowest line of sloping roof towards ridge. (e) Over the APP membrane, apply a coat of semi hot blown 85/25 penetration grade bitumen confirming to IS-702 @ 1.20 Kg/ sqm and blinded with fine sand in dry condition @ 0.50 Kg / Sqm dusted over the bitumen coat Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (ii) Ponding test shall be conducted for 72 hrs as directed.items and same shall be returned to contractor on satisfactory completion of guarantee period of 10 years. Special steel supports to be provided at certain places while dismantling the top layer as directed and specified by Engr - in - Charge.

M&L for 12 mm thick prelaminated particle board, interior grade both side decorative choice lamination fixed to aluminium doors or similar works including takingdown of old board, complete all as specfied and as directed.

Dismantling post or struts (wood, steel or RCC) any section any section, including taking out embedded portion and making good disturbed ground, complete all as specfied and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm watering and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil, complete all as specfied and as directed.

S&F angle iron posts or struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, and grills and grating and for iron frame works similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for painting to new steel surfaces of any dedcription over 10 cm in with or girth,not otherwise describe and applying two coats of synthetic enamel paints over a coat of red oxide primer, complete all as specified and directed.

S&F for galvanised iron chain link fencing with 3.8mm to 4mm dia wire mesh size 100mm X 100mm (as per sample approved by GE) complete after dismantling of old unserviceable chain-link fencing of any type, complete all as specified and directed.

M&L for plain cement convrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in fondation, filling and mass concrete, complete all as specified and directed.

M & L for colored chequered cement concrete tiles of size 300x300x25 mm thick with grey cement and pigment laid over and including 20mm thick cement screed bed in cemen t mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor including dismantling of old tiles incl cement mortar bedding and removing rubbish off the premises, complete all as specified and directed.

M&L for minimum 60mm thick precast PCC interlocking blocks of grade M-35 single layer monolithic high density manufactured by electro vibro hydraulically operated block making machine confirming to IS-15658 : 2006 in equal proportion of grey and coloured tile to make a pattern as directed, laid over and including 25mm thick sand cusion including demolition of old tiles, complete all as specified and directed.

Taking down rolling shutters of any description not exceeding 10 Sq.m area each opening and loabour only for repair and servicing of rolling shutters and removing of wom out components such as hood cover, laths, ball bearings, helical wire spring, lock plates, bracket plates, shaft pipe, guide channel and straightening of existing laths at required places and refixing the same to the original position including greasing/oiling i.e. complete servicing to make the shutter fully functional to the entire satisfaction of Engineer-in-Charge. Note:- (a) Labour charges for repair/replacement work and Material and labour charges for oiling & greasing deemed to be included in the quoted rate. (b) Items/parts required to be replaced shall be measured and paid separately under respective BoQ item.

Supply only for curtain built up of interlocking laths 75mmX1m thick section formed cold rolled steel strips with interlocking curls at both edges and deep corrugation at the centre with a bridge depth of not less than 12 mm to provide sufficient curtain stiffness including one coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces, complete all as specified and directed.

Supply only for lock plate ( width 125 mm made out of MS sheet 3.15 mm thick welded with MS angle 35x35x3 mm at the bottom and shall be fitted with MS sloding flat, interior and exterior sides of lock plates, complete all as specified and directed.

Supply only for MS guide channel of 3.15mm thick and 65 mm wide for rolling shutters with necessary holdfasts (ISA 40x40x6mm) as required at site, complete all as specified and directed.

Supply only for bracket plate made up 3 mm thick mild steel plate with 'U' clamp and stopper made up flat iron 40X6mm and welded to the appropriate place com plete and fixed to wall with foundation bolts at the required height, complete all as specified and directed.

Supply only for MS hood cover made out of 1.00 mm thick CRCA sheet to the rolling shutter for various opening, complete all as specified and directed.

Taking down for old unserviceable rolling shutters/collapsable gates of any description alongwith its accessories, complete all as specified and directed.

Supply & fixing for roller made of heavy duty 40/50mm dia pipe for shaft fixed with heavy duty springs, MS pulley to meet the standards for smooth functioning of rolling shutter including necessary nuts and bolts, split pins, holes etc, complete all as specified and directed.

Supply & fixing for 1.25mm thick steel rolling shutters with ball bearing of push/ pull or manual type as specified, including top cover, anchoring rod, hasp & staple and one shop coat of primer; erected in position as indicated after taking down of old unserviceable rolling shutter, complete all as specified and as directed .

Supply & fixing for collapsible steel gate (MS) consisting of channel pickets, pivoted flat bars, top and bottom runners, handles etc, as specified errected in position and securing runners with hold fasts and brackets, complete all as specified and directed.

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required, complete all as specified and directed.

M/s Anil Engineers & Builders (BID ID -3402919)

M/S IMRAN MAJID (BID ID -3394734)

M/S BADRI NATH GUPTA (BID ID -3392191)