REPAIR/MAINTENANCE OF INDOOR AND OUTDOOR WATER SUPPLY INSTALLATIONS INCLUDING MAINTENANCE AND CLEANING OF SEWAGE DISPOSAL SYSTEM AT MIL STATION NAHAN UNDER GE CHANDIGARH

Amount

Excavation in trenches in soft/loose soil not exceeding 1.50 meter wide and not exceeding 1.5 meter in depth; for foundation or for shafts, wells, cesspits, manholes, pierholes, etc. not exceeding 10 sq. m on plan and getting out complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick each in soft/loose soil, complete, all as specified and directed by Engineer-in-Charge.

Removing of surplus soil/ excavated material to a distance not exceeding 250 metre but not exceeding 500 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete, all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete of any description and in any position complete all as specified and directed by Engineer in Charge.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, incl nainital or similar pattern roof covering complete all as specified and as directed

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots all as specified.

Dismantling mild steel work of any description not otherwise provided for in any location and any position complete all as specified and directed.

Dismantling water tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, and removing from site complete all as specified and directed by Engineer-in-Charge.

Demolition of existing mud phuska, brick Koba waterproofing treatment, bringing it down carefully, removal of debris from the site and depositing where directed at a distance exc 1.00 Km but n exc 2.00Km complete all as specified and directed.

Dismantling existing waterproofing treatment hessian cloth base, membrane or any type including removal of debris from the site and depositing as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Taking down CI soil waste or vent pipe 75mm bore including all fittings like trapes,bends,junctions etc from any situation complete all as per specified and as directed

Dismantling of cast iron drain pipes, 100 mm dia, jointed in cement mortar and taking out of trenches, complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up salt glazed stone ware pipe 100mm dia set in cement mortar , complete all as specified.

Demolition and breaking up salt glazed stone ware pipe 150mm dia set in cement mortar , complete all as specified.

Dismantling of reinforced concrete drain pipes, 300mm dia, jointed in cement mortar and taking out of trenches, complete all as specified and directed.

Dismantling of reinforced concrete drain pipes, 150mm dia, jointed in cement mortar and taking out of trenches, complete all as specified and directed.

M&L for 100mm dia salt glazed stone ware (grade ‘A’) pipe laid in trenches including jointing testing etc, complete all as specified.

M&L for 150mm dia salt glazed stone ware (grade ‘A’) pipe laid in trenches including jointing testing etc, complete all as specified.

Reinforced concrete pipes ,300 mm bore, class NP2, laid and jointed complete with collars laid in trenches at any depth including jointing and testing complete all as specified and directed.

Reinforced concrete pipes ,150 mm bore, class NP2, laid and jointed complete with collars laid in trenches at any depth including jointing and testing complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (40mm graded aggregate) bed to drain pipes including packing under & haunching & benching against the side of pipe after they are laid and tested in 100mm dia of salt glazed stone ware (grade ‘A’) pipes complete all as specified.

M&L PCC 1:4:8 type D-2 (40mm graded aggregate) bed to drain pipes including packing under & haunching & benching against the side of pipe after they are laid and tested in 100mm dia of salt glazed stone ware (grade ‘A’)/ RCC hume pipes complete all as specified.

M&L PCC 1:4:8 type D-2 (40mm graded aggregate) bed to drain pipes including packing under & haunching & benching against the side of pipe after they are laid and tested in 300mm dia of pipe complete all as specified.

S&F Cast iron soil, waste and vent pipe in any length with or without ears, with cement joints, laid in trenches or in floor 100 MM dia, complete all as specified and directed.

All as per item no.32 above but fixed to wall.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, aid in trenches or in floors all as specified and directed by Engineer-in-Charge.

75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed by Engineer-in-Charge.

75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

S&F 110MM PVC (SWR) P trap, complete all as per specified and as directed

S&F 110MM PVC (SWR) S trap, complete all as per specified and as directed

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

S&F Cast iron in repair Bends (any radius), diminishing pieces or tapers (larger bore measured) 100 mm bore with ovel access door complete all as specified and directed.

S&F Cast iron in repair Bends (any radius), diminishing pieces or tapers (larger bore measured) 75 mm bore with ovel access door complete all as specified and directed.

Plain cement concrete (1:3:6) type C-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L Cement concrete in surface channels and drains in cement concrete 1:3:6 type C1 (20 mm graded stone aggregate), complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

M&L for providing precast RCC 1:2:4 type B1 ( using 20 mm graded stone aggregate) as in manhole cover slabs etc set in CM 1:4 including necessary form work and handling and placing on manholes, complete all as specified. Note: Reinforcement measured and paid seperately

Hardcore broken stone of gauge not exceeding 63mm deposited, spread & leveled in layers not exc 15cm thick watered, rolled and rammed to a true surface complete all as specified.

M&L for Plain cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in Plinth protection,75mm thick finished even and fair complete including necessary form work all as specified .

Forming contraction (dummy) joints 25 mm deep x 10mm wide, filled with sealing compound Grade A complete all as specified and as directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all specified and as directed.

Reinforced Cement Concrete Nominal mix ( 1 :2:4) using 12.5mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slab, landings and similar work not exceeding 200mm thick, horizontal or sloping finished rough complete all as specified and directed by Engineer-in-Charge.

25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in levelling concrete etc. complete all as specified and directed by Engineer-in-Charge.

M&L 75 mm thick Cement concrete type D2,1:4:8 (40mm graded stone aggregate) as in sub base,path,floor, hardstanding complete as as specified and directed.

M&L for Stone kerb of roughly squared stones of size 15cm x 30cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar1:6 and struck flush , complete, all as specified and directed.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. Note: Water proofing compound shall be measured and paid separately.

Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 5 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Supply only liquid water proofing compound.(Make- Bostik, Dr fixit, Fosroc, or Equivalent)

Preparation of new plastered surfaces of wall and applying two coats of cement base paint on walls over and including a coat of primer including preparation of surface complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of primer and 2mm wall care puty including preparation of surface complete all as specified and directed.

Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 6mm to 8 mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

M&L for Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in PCC (1:2:4) type B-1 smooth finished for 150 mm internal dia of pipe, complete all as specified and directed by Engineer-in-Charge.

Supplying & fixing of PVC water storage tank 1000 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made Plain, framed, panelled shutters of 2nd class Hardwood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkat complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size of stiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Factory made solid panels PVC shutters 30mm thick (styles) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for styles & wood grain printed PVC sheet for to rail lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail paneling of panel colour PVC sheet to be fitted in the MS frame welded/scaled to the stiles & rail with suitable PVC sheet beading & jointed together with solvent cement supply & fixing in the frame at site as per specification & drawing.

S&F stainless steel Butt hinge 100mm size,complete all as specified and directed.

S&F 150mm size, Stainless Steel, D type with back plate, handle and fixed with screws complete all as specified.

S&F aluminium anodised barrel tower bolts of extruded section 150 mm long,complete all as specified and directed.

S&F 300mm Mild steel sliding door bolts,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane, complete all as specified and directed by Engineer-in-Charge.

4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Providing and fixing anodised aluminium work for door windows, ventilators, casement/sliding shutters and partitions with extruded built up standard tabular and other sections of approval make fixed with rawl plugs and screws or with fixing clips or with expansion hold fastner incl neceesary filling up of gaps at junctions at top bottom & sides with required PVC neoprene belt etc. Aluminium section shall be smooth rust free straight mitred and jointed mechanically where ever required including cleats angles, aluminium snap beading for glazing/panelling, CP brass/stainless steel screw incl providing hinges/pivot and making provision for fixing of fittings where ever required. (Note:- The rate is inclusive of rollers, Maruti locks/star locks, robber beading, rubber seal etc for sliding/casement shutters required for satisfactory operations of window/ventilators/doors or as directed by Engineer-in-Charge. 2. panel fillings other than aluminium filling and necessary fittings shall be measured and paid for seoparately under respective items.)

Preparation of old steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Glazed ceramic coloured tiles 450 x 300 x 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed in neat cement mortar and pointed in white or colour cement to match tiles complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed in neat cement mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

Cleaning under ground sewage line 100mm dia full of waste solids/liquid mud or sludge deposited in these lines by rodding manually or through mechanical means between manholes and removing sludge (obtained from cleaning of sewage line) to a distance exc 100M but n.exc 150M from the site and disposed off as per the directions of Enginer-in-charge.

All as per Srl item No 89 above but 150mm dia of pipe.

S&F Iin repair chromium plated perforated grating 100/150mm dia over Floor/Nahani trap with or without hole for waste pipe fixed with white cement mixed with pigment to match the shade of floor fixed in repair, all as directed by Engineer-in-charge.

Dewatering/Desludging of manholes 1.2m X 1.2m,upto 1.5M depth , desilting and removing sludge from manholes as in foul conditions and removing of sludge up to distance exc 150M and n.exc 200M and deposited in borrow pits including excavation of borrow pits and covered with 10cm thick layers of soil and disposed off surplus soil, refixing manhole cover etc, complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 92 above but exc 1.5M depth.

Dewatering / Desludging of liquid / mud / solids (work in foul conditions) from septic tank of any depth and removing sludge out of MOD land to a distance exc 1 Km but not exc 2 Km and deposited in borrow pits including excavation for borrow pits and covered with 10cm thick layer of soil over sludge and spreading the balance near by in low lying area including taking up and refixing of covers of septic tank of 25 users complete as per the direction of Engineer-in-charge.

All as per Srl No.94 above but septic tanks of 50 users

All as per Srl No.94 above but septic tanks of 100 users

All as per Srl No.94 above but septic tanks of 150 users

All as per Srl No.94 above but septic tanks of 200 users Note: For item No 94 to 98. Dewatered/desludged waste shall be conveyed by truck/tractor mounted covered trailers and deposited off as directed beyond MOD land.

Cleaning / blockage of 'S' trap/'P' trap/WC's (Orissa Pattern/ European/Indian Type) /WHB / Urinal /floor trap /Gully trap,nahani trap in running/flowing order without disturbance by removal of blockage of any type by deploying sufficient Nos of Safaiwalas and making fully functional at any location and at any floor in the area covered by military station NAHAN including all the T&P reuired for the purpose complete all as specified and directed by Engineer-in -Charge.

Cleaning of blockage sewage pipe line any bore/any type in running/flowing order without disturbance by removal of blockage of any type incl all T&P required by deploying sufficient Nos of Safaiwala and making fully functional at any location and at any floor in the area covered by military station Nahan including all the T&P reuired for the purpose complete all as specified and directed by Engineer-in -Charge Note:-Note for Ser item No 99 & 100: (a) The quantity of unclogging chemical as required will be measured and paid for seperately. (b) The contractor will provide suffiecient Safaiwalas per day for 08 Hrs to attend the above complaints for complete tenure of contract. The quoted rates of the contractor deemed to include the cost of aforesaid manpower. (c) All the safaiwalas employed by contractor shall attend the MES complaint cell of AGE B/R Army at military station Nahan at 08:30 Hrs to collect the complaints from the concerned JE and submit the minor complaints duly signed by the occupant at 1630 Hrs same day and major complaints within the 24 Hrs of working day in the complaint cell. It will be responsibility of contractor to ensure their attendance & completion of complaints. If complaints not cleared by in specific time an penalty of Rs 500/- will be recover from the contractor per complaint. The contractor will ensure the cleaning/clearing of all the complaints (irrespective of Nos) within time by deploying addl workers if needed. Nothing extra will be paid on this account. (d) The contractor shall be solely responsible for supplying all the safety equipments and observing safety rules required by the safaiwalas during working Hrs as per Govt policies in vogue and as amended time to time. (e) All the waste material / sludge shall be disposed off outside MD land.

S&F stack clamps for 110 mm dia PVC(SWR) pipes of 50mm x 5mm flat iron and 16mm dia round iron stay bolts and nuts and securing ends of stays to wall and roofs, fixed in repairs all as specified and directed.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 25 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

Cutting chases in stone wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, Complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan pedastal pattern white including PVC valveless, syphonic action type, flushing cistern 10 ltr, low level, white, with inlet, ball valve, float,hockey stick and handle including brackets, complete all as specified and as directed. Note : The quoted rate shall include provision of "P" Cast Iron trap.

S&F in repair vitreous china floor mounted wash down one piece water closet pan white (including seat cover ,fixing bolts, flush cistern 10 ltr capacity) complete all as specified and directed. Note : The quoted rate shall include provision of "P" Cast Iron trap.

S&F in repair Vitreous China Squatting pan, 'Orissa pattern, size 580x440 mm white with integral foot rests including PVC valveless, syphonic action type, flushing cistern 10 litre, low level, white, with inlet, ball valve, float,hockey stick and handle including brackets, complete all as specified and as directed. Note : The quoted rate shall include provision of "P" Cast Iron trap.

10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs vitreous china wash hand basin white flat back of size 550x400mm including CI brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Supplying and fixing in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15mm bore stop valves/angle valve cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle complete all as specified and directed by Engineer-in-Charge.

S&F in repair kitchen Plate Rack stainless steel having size 600mm x900mm x250mm (approx) incl fixing to walls with fasteing screws, rubber/PVC beading /capping complete to sustain utensils weight upto 8-10 Kg, complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 800mm to 1000 mm long fixed to wash fitting of wash basin and sink all as specified and directed.

Supplying and fixing in repairs fancy type shower rose 125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint in including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe incl bedding in cement mortor to dwarf wall ot cantilever brackets and connecting union to pipe overall size 495x420mm, bowl size 410x 330x160mm incl all fittings ie chromium plated waste coupling, waste pipe complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25mm dia aluminium curtain rod with & including hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

S&F Door strip (snake guard strip) minimum 18mm wide aluminium body and nylon brushes minimum 22mm wide alongwith screw fixing complete all as specified and directed.

S&F in repair 15mm dia Ball brass valves high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed

Chromium Plated health faucet 2 in 1 including 1.50 mtr long flexible tube with hook complete all as specified and directed by Engineer-in-Charge'.

S&F in repair PVC connections 15mm size with brass chromium nuts of length 450mm, Complete all as specified and as directed

Supply and fixed in repair brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

Granite jet black shade, 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, fascia, valleys, gutters etc. fixed with self tapping screws complete all as specified and as directed.

S&F Fe-410-W(Gde E-250)quality B rolled mild steel in roof, as in posts trusses(Framed)trusses, purlin, crane gantries, as in posts, rails and framing(beam, tee, angle, channel or flat section) including distance pieces , cleats etc, complete all as specified and as directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; tank staging, fascia gutter ,walk ways; railings; and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along externalwall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface ofthe sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified.

Providing and laying 3mm thick APP modified prefabricated five layer , weight not less than 3.0 kg / sqm water proofing membrance, black finished, reinforced with non-voven polyster matt make as approved, consisting of a coat of bitumen primer @0.40 ltr/sqm by the same membrance manufacture of density 0.87 to 0.89 kg/ltr at 25 degree C temperature and viscosity 70-160 CPS . Over the primer coat the layer membrance shall be laid using butane torch and sealing all joints finally and applying two coats of bitumenous aluminum paint @ 0.20 kg per sqm over APP membrane etc after preparing the surface complete as per manufacture's instruction complete all as specified and directed by Engr-in-charge.

Prepolished PCC factory made tiles, ISI marked, 20 mm thick of size 200 mm x 200 mm, machine pressed and cut polished and set jointed and pointed in neat cement slurry and fabricated using grey cement & pigments. over and including 15 mm thick cement mortar (1:4) bedding joints grouted flush in cement mortar (1:3) complete all as specified and directed by Engineer-in-Charge.

Material & labour for chequered cement concrete coloured tiles 20cm x 20cm x 25mm thick, with grey cement and pigment, jointed and pointed in neat cement slurry in floor laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

Supply and Fixing only chain link fencing 50mmX50mm mesh or cages with 4mm dia including line wires, rails, straining bolts, etc. including provission of binding wire, complete all as specified and as directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed.

Taking down Copper/Aluminium point wiring (light, fan, socket or power) complete, any type / size complete with removing all connection and accessories, fittings and fixtures such as switches , sockets, ceiling rose,pendent holder,fan regulator any type , all type of tube light fitting , batten , steel or PVC conduit , casing caping etc compele and making good the disturbed surface of wall , floor etc. complete all as specified and directed by Engineer-in-Charge. Note :-- Rates for cutting/chases in walls and making good disturbed area deemed to be included in the quoted rate

Taking down MCB DB/Meter box/junction box /Ac Box of any size and disposal under schedule of credit and making good disturbed surfaces all as specified and directed.

Taking down old unserviceable light fittings any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed by Engineer-in-Charge to match with existing surface all as directed.

Point wiring using approved colour coding as per IS ,with stranded copper conductor 1.5 sqmm (nominal area ) single core , flame retardant low smoke and low halogen FRLSH PVC insulated unsheathed , 1100 V grade conforming to IS 694 ,marked TEC and FIA approved in and including PVC conduit medium grade ISI marked 20mm dia with all fittings and accessories, concealed type/ surface type (surface type only on ceiling), PVC junction boxes, modular metal sunken/flush boxes of any modules from 2 to 18 Modules with Inner and outer modular cover plates, including FRLSH flame retardant low smoke and low halogen rigid PVC insulated unsheathed stranded copper conductor 1.5 Sqmm (nominal area )single core cable as earth continuity conductor to common earth and connected to earth dolly for One light point controlled by one switch or one (Ceiling/ Wall/ Exhaust) fan point ,bell controlled by one switch and regulator complete all as specified and directed by Engr-in-charge. Note :- 1. Cutting/chasing of wall etc. deemed to be included in the quoted rate of this item. 2. Modular metal flush/sunken Box along with modular switch/socket cover plate & sheet are inclusive in the item rate quoted. 3. Only switch socket and fan regulators to be measured and paid separately

All as per item No 141 above but for one 3 pin 5 Amp socket on same board all as directed.

All as per item No 141 above but for one 3 pin 5 Amp socket on indipendant board all as directed.

All as per item No 141 above but for but with 4 sqmm copper conductor for 15 amp socket with 2.5 sqmm earth continuity conductor.

S&F of Modular snap switch Single Pole one way 5/6 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5 pin ,5/6 Amps suitable for 2 Module complete all as specified and directed.

S&F of Modular snap switch SP, one way 15/16 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5/6 pin, 15/16 Amps suitable for 2 Module complete all as specified and directed.

S&F of Modular Fan step Regulator electronic, 120 watts, 2 Module complete all as specified and directed.

S&F of Modular blanking plate suitable for 1 Module complete all as specified and directed.

S&F of Modular white cover plate incl Modular base frame & powder coated Modular sheet metal concealed box for 12/8 module complete all as specified and directed.

All as per Item No 150 above but 6/4 module complete all as specified and directed.

All as per Item No 150 above but 3 module complete all as specified and directed.

All as per Item No 150 above but 2 module complete all as specified and directed.

S&F of ceiling rose surface backalite 65mm x 50 mm, two to three terminals complete all as specified and directed.

Supply and fixing of lamp holder insulated body with back plate suitable for any type of fitting complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC,decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing of Indoor Decorative LED box type suitable for fixing ceiling/wall with aluminium base directly retro fit LED tube Light , 22 watt, , Color: Cool day light 4 ft white Operating Voltage: 140-270 volts complete with all accessories internally pre wired and including up with three core PVC copper flexible cable of size 23/0.0076 from ceiling rose to connector block complete all as specified and directed LED batten & LED tube rod shall be of same brand.

Supply and fixing of LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed.

Supply and fixing of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as directed.

All as per item No 159 above but SPN 04 way, 240 volts complete all as directed.

S&F of isolator DP 63 amp 230 Volt complete all as specified and directed.

S&F of isolator SP, 6-40 Amps, 230 Volts complete all as specified and directed.

Taking down and re fixing the existing water geyser/ Ceiling fan/exhaust fan any type and any size after necessary servicing/greasing complete incl painting all as specified and directed by Engr-in-Charge to match with existing surface complete all as specified and directed.

Supply and fixing in replacement of Energy saving LED security light fitting 70 Watt 230 V, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete complete all as per manufacturers specifications including taking down old unsv fittings of any size / watt complete all as specified and directed.

Supply and fix in replacement of security light fitting bracket made up of 32/40 mm dia medium grade pipe of length 0.9 mtr with bending in shape by hot or cold method with 2 nos 50x4 mm MS flate clamps with nut bolts and washer etc all as directed

Supply and fixing of Exhaust fan 380 mm sweep heavy duty complete with self closing MS louvers, mounted in suitable opening arrangement and suitable for operation on 230/240 Volts, single phase, 50 Hz,1400 RPM , AC supply with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm and making all necessary connection and fixed by using 4 Nos 100 mm long 10 mm dia bolts, nuts and washers and grouted in wall in CM 1:3 (including opening of wall etc) completed all as directed. Note: The UNSV old one Item Srl No 166 is MES property and will be handed over to MES Store Yard .

Earthing complete with Galvanised steel earth plate electrode of size 60cmx 60cm x 6mm thick electrode buried directly in ground (earth pit not less than 2.25 meters deep below the normal ground level) with top edge of the plate not less than 1.5 m below normal Ground Level connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers and earth lead protected by 15mm dia GI pipe medium grade connected to main distribution board/ earthing test point all as shown on electrical plate No-03 of SSR Part-1 and all as specified including testing on completion.Note: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bars @ 150mm c/c both ways , GI funnel with watering pipe 20 mm dia, wire mesh, salt and charcoal, protection pipe for earth lead upto 7.50m long complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified in SSR part-II earth lead wire and protection pipe beyond 7.5m shall be measured and paid separately.

S&F of Glow Sign board of following size and showing given name on Acrylic sheet/Fibre glass re-inforced translucent corrugated sheet 2mm thick with MES Logo (symbol) necessary Vinyl Blue Sticker along with 02 No's LED Tube light fitting 22 watts incl nessary connection with 1.5 Sqmm flexible copper wire and fixed on structure with aluminum equal angle as per required size , sufficient Nos brass machine screws complete all as directed.GLOW SIGN BOARD SIZE (a) 1.50m x 0.45m x 0.20m-01 No KEY PERSON ACCN Rest of the sides of the structure except front side will be covered with galvanized plain sheet 0.80mm thickness with zinc coating both sides fitted with nut, bolt washer 25mm length 6mm dia-04 Set Bottom support:- M&L for angle iron size 50mm x 50mm x 6mm length 08 ft –02 Nos grouted in suitable PCC 1:4:8 type D2 40mm graded platform with cement plastering for fixing the glow sign board all as directed by Engr-in-Charge-03 Sets . Note:- All galvanized plain sheet and equal angle iron painted with 2 coat of synthetic enamel paint over a one coat of red oxide paint as per approved colour included in this quoted rate all as directed by Engr-in-Charge-04 Set

Supply and fixing in replacement of 1100 volts grade heavy duty cable PVC insulated aluminiumconductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 06 sqmm 2 core complete all as directed.

Supply, Install, jointing, connecting and testing complete Automatic Star-Delta starter suitable for 100 HP , 110 KW, 415 Volts in stainless steel housing IP 54 protection class with built in relays suitable for 100 HP pump set including dismantling/taking out unserviceable existing starters complete all as specified and directed.

M/S SHANTI SARUP DINESH CHAND (BID ID -3302068)

His Construction Company (BID ID -3307415)