PROVN OF PARTITION OF BLDG NO T-06 AND T-07 WITH TWO ATTACHED TOILET BLOCKS AT CERTAIN UNITS AND SPECIAL REPAIR OF SHED P-18(CAMP STORE) OF CERTAIN MIL UNITS UNDER GE (S) BINNAGURI

Amount

Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and removal off the site.

Dismantling wrought iron or mild steel work of any description as in door, gates , truss etc and similar works complete all as specified and removal off the site.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and removal off the site.

Demolition of brickwork or stone/boulder masonry, built in cement mortar complete all as specified and removal off the site.

Taking down of cement plaster on brick (or) concrete wall including racking out joints hakins for key sinebling down with water etc complete all as specified and removal off the site.

Taking down chowkat or frame with door shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each, making good disturbed surfaces and removing materials from site of work complete all as specified and removal off the site.

Surface excavation n.exc (not exceeding) 7.50 cm deep and averaging 15cm deep and getting out complete all as specified.

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in soft/loose soil complete all as specified.

M&L for Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified.

M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified.

Material and labour for reinforced cement concrete (nominal mix) Type A1 1:1.5:3 (using 20mm graded stone aggregate) as in foundation, footings, plinth beams, bases for columns and the likes complete all as specified. Note: Reinforcement and formwork shall be measured and paid for separately.

Material and labour for precast reinforced cement concrete (nominal mix) Type A1 1:1.5:3 (20mm graded stone aggregate) as in lintle and the like over 1.5m span etc and set in CM (1:4) including necessary formwork complete all as specified. Note:- Reinforcement shall be measured and paid for separately.

Material and labour for RCC 1:11/2:3 type A-1 (nominal mix) (using 20mm graded stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as directed. Note: Reinforcement and formwork shall be measured and paid for separately.

Material and labour for reinforced cement concrete (nominal mix) Type A1 1:1.5:3 (20mm graded stone aggregate) as in columns and the like above footings etc complete all as specified. Note: Reinforcement and formwork shall be measured and paid for separately.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Ditto as per item no 15.00 but 6 to 8mm dia complete all as specified.

Use & waste of Formwork flat fair finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

Use & waste of Formwork flat fair finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified.

Use & waste of Formwork square, rectangular or plougonal fair finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

Use & waste of for Formwork to flat fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landings , shelf and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified.

M&L for Flyash Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortor 1:6 complete all as specified.

M& L for Fly ash Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified.

Material and labour rendering 20mm thick cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces in two layers 10mm thick each layer and top layer mixed with integral water proofing compound all as per manufacturer's instruction and as specified. Make: 'Plastocrete Plus' of Sika/ 'Pidiproof LW' of Pidilite for water proofing compound. Note: WPC shall be measured and paid for separately as 'Supply only'.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:6), finished surfaces even and smooth complete all as specified.

M&L for rendering on walls ,15 mm thick in cement mortar (1:4) mixed with water proofing compound , on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified.

M&L 5mm thick with CM (1:3) on or concrete surfaces finished even and smooth as in ceiling complete all as specified.

M&L for preparing new plastered surfaces of wall and applying two coat of distemper oil emulsion over a coat of primer complete all as specified.

M&L for preparation new plaster surfaces of wall and applying two coats of cement base paint complete all as specified.

M&L preparation of new plaster surface of ceiling and applying two coats of white wash complete all as specified.

M&L for preparing new plastered surfaces of wall and applying two coat of white wash complete all as specified.

M&L for preparing old plastered surfaces of wall and applying two coat of white wash complete all as specified.

Hardcore of gauge n exc. 63 mm, except material retreived from item 1 deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface complete all as specified.

M&L silver sand filling under floors or in foundations including watering and consolidation complete all as specified.

M&L 100 mm PCC (1:4:8) type D-2 using 40 mm graded stone agg as in sub base complete all as specified.

M&L for 40mm cement concrete type B-1 1:2:4 (20 mm graded stone aggregate) as in floor finished complete all as specified.

M&L for 75mm PCC 1:3:6 type C-1 using 20 mm graded stone agg as in plinth protection complete all as specified.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in path /steps laid with and incl use and waste of form work and finishing the surface even and rough to receive the topping layer or tiling complete all as specified.

M&L for Framed work such as grills, framed guard bars,for window by welding it to existing window frame and similar work con- forming to Fe.290.Gde-E-165 complete all as specified.

S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specifed.

S&F of 4 mm thick Sheet glass frosted , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

Supply and fix 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50sqm in each pane complete all as specified.

M&L for two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10 cm width or girth complete all as specified.

M&L preparing old painted steel surface of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified.

M & L preparation of new surface & applying two coats of synthetic enamel paint over a coat of pink primer to wooden surfaces exc 10 cm girth complete all as specified.

M&L preparing old painted wooden surface of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified.

Supply and fixing for vitreous China white wash down water closet pan (pedestal pattern) with ‘P’ or ‘S’ trap complete, front or back inlet, fixing bolts, PVC seat cover including 32 mm dia PVC flush pipe and making all necessary connections complete as specified. Make: Hindware Cat No 20012 or equivalent.

S/F in 10 litres cap PVC low level valve less symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and flushing pipe, complete all as specified.

Supply and fix vitreous China wash basin white, flat back, size 550 x 400 mm with CP brackets (02 Nos) including cutting for pinning in ends of brackets and making good disturbed surfaces with CM (1:4) complete all as specified. Make:-HINDWARE Cat No 10054 (Mini Regal) or equivalent.

S&F 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S&F 15 mm dial PVC connection 450 mm long, complete all as specified.

S&F waste coupling of PTMT (half of full threaded) complete all as specified.

S&F 32 bore PTMT Wash hand basin waste pipe 90 cm long complete all as specified.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified.

S&F swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified.

S&F 15mm bore Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F 15 mm bore Stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

M&L for glazed ceramic coloured joint free tiles 300x450x7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. in Bath, WC, Kitchen and inside cupboards set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 10 mm thick rendering in cement mortar 1:4 complete all as specified.

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile including 15mm thick screed bed in cement mortor 1:6 complete all as specified

M&L for PVC Floot trap 100 mm outlet, plain with grating including joning with solvent cement complete all as specified.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

Supply and fix PVC (SWR) pipes 110mm dia,type 'A' conforming to IS, single socketed, in any length with rubber ring joints laid in trenches or floor complete all as specified.

Supply and fix PVC (SWR) pipes 75mm dia,type 'A' conforming to IS, single socketed, in any length with rubber ring joints laid in trenches or floor complete all as specified.

M&L for 75mm bore PVC (SWR) vent cowl complete all as specified.

M&L PVC (SWR) bends with access door of 110mm bore any radius complete all as specified.

Material and labour for hoisting and fixing rotational moulded polyethylene(double layer) LLDPE water storage tanks 1000 lit capacity (Cylinderical vertical with polythene foam insulation as intermediate layer), ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet and over flow connection etc complete all as specified.

Material and labour rendering 15mm thick screed bed in CM 1:4 mixed with liquid water proofing compound all as per manufacturer's instruction and as specified. Make: 'Plastocrete Plus' of Sika/ 'Pidiproof LW' of Pidilite for water proofing compound. Note: (i) WPC shall be measured and paid for separately as 'Supply only'. (ii) WPC to be mixed @200ml per 50 Kg bag of cement all as manufacturers instruction.

Supply only liquid water proofing compound complete all as specified.

-----Blank-----

Supply and laying APP 3mm thick five layered polymeric membrane (weight not less than 3 Kg per Sqm) reinforced with non-woven polyester matt of central core 90 micron thick (weight not less than 150gms/sqm) high density polythene film, protected on both sides with high quality polymeric asphaltic mix protected on both sides with thermo-fusible HM HDPE film laid on and including primed surface primed with oil based primer @0.40kg/sqm by torch application all as per manufacturer’s specification and the top surface treated with aluminium paint @0.15Kg/sqm all as specified. Make: “Torchshield P3160” of Pidilite/ “Super thermolay of STP or equivalent. Note: (i) Membrane shall be laid using butane torch and sealing all joints etc all as per Para 11.44.5 of SSR Part-I.

-----Blank-----

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 Cm complete all as specified.

Removing excavated material exc 1.5 km n.exc 5 KM and depositing where directed at a level n exc 1.5 mtr above the starting point complete all as specified.

Removing excavated material ( soil) n. exc 50 m depositing where directed at a level n. exc 1.50 m above the starting point complete all as specified.

S&F 15 mm dia medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors complete all as specified.

All as per item no 75.00 above but 20 mm bore pipe complete all as specified.

M& L for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified.

S&F Stainless steel butt hinges medium weight 100mm long for PVC door complete all as specified.

S&F Aluminium anodized barrel tower bolts, extruded section 200mm long complete all as specified.

S&F Aluminium anodized handles, D type, 150mm long complete all as specified.

S&F Pressed steel door frames of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

S&F 35 mm thick Second class Hardwood factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified.

M & L PCC (1:3:6) type C1 as in holdfast block, coping, bedblock etc.complete all as specified.

M & L for PCC 1:2:4 type B-I ,(using 20 mm graded stone aggregate) as. in footpath coping /benching to sides of foot path fininished fair and even etc complete all as specified.

S&F in aluminium sliding door bolt 300 mmlong, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate.

Supply and fix vitreous China flat back urinals(white) of size 440mm x 315mm x 265mm, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including waste pipe, 15mm dia PVC connector pipe , CP urinal spreader complete all as specified. Make: Hindware Cat No 60001 or equivalent.

Supply and fix anodised aluminium frame powder coated for partition (minimum thickness of powder coating 50 micron) with one or more rebates including and joining cleat for fixing , glazing clips, rubber packing screws etc.complete all as specified.

M& L for Prelaminated Particle board 12 mm thick interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screw to timber frame work complete all as specified.

M& L for fabrication and fixing of powder coated aluminium door shutter fixed with rubber gasket, stopper, cleats, handles etc complete for aluminium frame of size 101.6mm x 44.45mm x 2mm and section of bottom and top rail of section114mmx44.45mmx2mm thick and and lock rail shutter frame of 83mm x 44.45mm x 2 mm with and including panels of 5.5 mm thick plain/frosted float glass,and with anodised aluminium snap beading of size 18.2mmx16.66mm scred for fixing fully including double action door spring hydraulically regulated made up of 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and all necessary fittinngsand EPDM rubber packing each shutter shall be provided with two decorative type aluminium disc handle of 150 mm dia per shutter ,1 no heavy duty door shutter 1no 200mm long aluminium tower bolt per shutter complete all as specified.

M&L for PCC for concrete bed to drain pipe , 200 mm bore pipe including packing and under hunching against the sides of pipe after they are laid and tested in PCC (1:3:6) type C-2 using 40 mm graded stone aggreagate complete all as specified.

-----Blank-----

M&L for 200mm bore grade 'A' SGSW drain pipe laidin trenches and jointed in cement ,mortar (1:1) complete all as specified.

-----Blank-----

M&L for 60mm thick M-35 grade factory made vibratory compected cement concrete rubber moulded, interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved all as specified.

Supply and fix 0.50mm thick prepainted galvalume polyester coated (SMP coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550Mpa as in roof covering fixed with self drilling screws with EPDM washer etc complete all as specified.

----Ditto--- all as per item No 97.00 above but as in eaves board fixed with selp tapping screw as specified.

M&L for 25 mm thick cement concrete type B0, 1:2:4 (12.5mm graded aggregate) as in floor etc and finishing cement concrete complete all as specified.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with M & L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified.

M & L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item 6 complete all as specified.

M & L for complete removal of existing treatment and finishing the walls with two coats Acrylic smooth exterior emulsion paint of required shade for New work over and including priming one coat of exterior primer applied all as per manufacturer's specification and as specified.

---Ditto--- all as per item No 102.00 above but for New plastered surfaces.

S&F steel work in tubular trusses i.e. Truss bottom, top bend, sides, side supports, holding plates, posts and base plate etc including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified.

S&F 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified.

M&L for cement concrete Type B1 1:2:4 (20mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified..

S&F mild steel wire cloth galvanized 0.56mm nominal dia and average width of aperture 1.18mm fixed with tinned tack or galvanized wire staple including all cuttings, wastage etc complete all as specified.

Supply & fixing in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless and as required framing including taking old one steel staples complete all as specified.

S&F in repairs factory made Z section steel window with side hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay, ms tower bolt etc. complete with glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete including taking out old one complete all as specified.

S&F in repairs factory made Z section steel ventilator with top hung shutter incl hinges, steel peg stay, with glazing bars including a shop coat Red Oxide priming including taking out old one , complete all as specified.

Hacking out old broken glass (any thickness ,size quality or description) from wooden/metal frame including punching or drilling out old glazing pins/spring clips glazed with putty and removing materials from site of work complete all as specified.

S & F in repairs steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod,hasp and staple and one shop coat of primer,erected in position as indicated, complete: push pull or manual type complete all as specified.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate ) as in surface channels and drains etc complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified.

M&L point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor,conforming to IS-694 of size 1.50 sqmm nominal cross sectional area single core drawn in and including PVC casing caping and fittings, including, pressed steel concealed terminal switch boxes not less than 1.2mm thick of reqd size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories, One light point controlled by one way switch 5/6 amps. complete all as specified.

ALL as per item no. 116 but One ceiling fan / exhaust fan point controlled by one way switch 5/6 amps complete all as specified.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sundn terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws (or provision of modular sunken box, modular back plate and top cover for housing of modular switch,socket, regulators etc as per site requirement) for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost , One light point controlled by one way switch 5/6 amps complete all as specified.

ALL as per item no. 118 but One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps complete all as specified.

ALL as per item no. 118 but One socket out let 5/6 amps point on the same board complete all as specified.

ALL as per item no. 118 but One socket out let 5/6 amps point on the independent board complete all as specified.

All as per item no 118 here in above but copper conductor of size 2.5 sqmm for 15/16 Amp socket on independent board complete all as specified.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified.

S&F switch piano flush type 5/6 amps single pole 2 way complete all as specified.

S & F Socket outlet 2 in 1,3 pin 15 Amp, flush type complete all as specified

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified.

S & F switch piano type one way, flush type 15 Amp complete all as specified

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified.

S & F deluxe fan electronic regulator 230 volts AC 50 Hzs rotary step white/ivory finish complete all as specified.

S & F IP 20 , LED Light 10 Watt ( 2 feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative end caps with integrated high efficiency electronic driver and surge suppressor of 2 KV or more, luminaire efficiency> 95 lumens/watt, power factor> 0.90, operating range 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up complete all as specified.

S & F LED street light fittings 35 watt in aluminium PDC housing, toughned glass cover with IP66 protection complete all as spedified.

M&L for street light bracket made out of GI pipe light grade 25 mm dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified.

M&L for street light bracket made out of GI pipe light grade 32 MM dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, single pole & neutral with din rail, IP-20 protection suitable for fixing MCB"S/lsolators complete including taking down the old one complete all as specified.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with din rail, IP-20 protection suitable for fixing MCB"S/lsolators complete including provision of blanking plates as required and taking down the old one complete all as specified.

S&F MCB, Single pole & neutral 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

Material and labour for sub-main wiring alongwith earth wire of size of 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC Casing caping with all fittings and accessories ISI marked all as specified and as directed. NOTE : Two runs of 4 sqmm conductor for main and one run of 4 sqmm conductor as earth wire with proper colour coding including one run of PVC casing caping shall be measured as one unit length. Connections of cables with MCBs or bus bar shall be done through appropriate size brass/ copper thimbles complete all as specified.

S & F exhaust fan , steel body AC single phase, 230 V of size 300 sweep with blades and frames and louvers completa all as specified.

S & F exhaust fan , steel body AC single phase, 230 V of size 450 mm sweep with blades and frames and louvers complete including cutting of wall as required complete all as specified.

Supply installation, commissioning and testing of electric water heater, storage vertical type, BEE 5 star rated 25 ltrs capacity 230 volts AC 50 Hz comprising of high wattage heating element for instant heating, rust & shock proof ABS outer body, non- ferrous pressure plate with and including provision of 02 Nos grouting bolts suitably flush to wall or any other surfaces and connection pipe for hot and cold water supply 25 lts BEE 5 Star rated complete stranded copper conductor cable/ flexible chord complete all as specified.

M&L for GI water tubing medium grade 15 mm dia fixed on wall with all fittings and fixtures complete all as specified.

Supply and lay pipe galvanized, “Medium class”, including fittings 25 mm complete all as specified.

Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified.

S&F, IP 20, class I, LED tube light fittings 20W (or nearest next higher wattage) (4feet), wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 16 sqmm 2 core with and including all fixing & connecting accessories such as Aluminium cable lugs, cable gland, nut, bolts, washer etc including taking out old cable complete as specified.

Supply and laying sub class B bricks of size 25cmx12.5cmx7.5cm (+/-10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified.

L. B. SHARMA (BID ID -3128995)

SHRI MRITYUNJOY KAR (BID ID -3130457)

MESSRS SEN BROTHERS (BID ID -3129940)

M/S NIKITA ENGINEERING CO (BID ID -3130062)

R K AGARWAL (BID ID -3130166)

M/s. RAMPHAL GARG (BID ID -3130338)

M/S PLABAN KUMAR GOPE (BID ID -3130212)