New Costruction Of Categoty E Type Judicial Bunglow At Barwala Di Botad

Name Of Work : New Construction of Category - E Type Judicial Officer

Bungalow at Barwala , Dist- Botad

Bill Of Quantity

Quantities Estimated Total amount

Quantities Estimated Total amount

estimated but rates. according to

Sr.no. Description of item Unit

may be more estimated

or less quantities.

Excavation for foundation upto 1.50 mt depth including sorting out

and stacking of useful materials and disposing the excavated stuff upto 50 mt

lead (B) Dense and hard Soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting

out and stacking of useful materials and disposing off the excavated

2 stuff upto 50 Meter lead.(B) Dense or Hard soil 49.00

Filling in foundation and plinth with sand in layers of 20 cm. Thickness

3 including watering ramming and consolidating etc. comp. 18.20

Filling available excavated Earth (Excluding Rock ) in trench plinth side of

foundation . in layer not excluding 20 cm in depth consolidation each

deposited layer by ramming and watering etc. complete

Filling foundation and plinth with murrum or selected soil in layer of 20 cm in

thickness including, ramming watering and consolidating etc. complete Cu.M.

Applying general insecticide pest control treatment to floors, cupboards etc

including labour material etc. complete. Using Heptachloride 20 EC. As Per

6113_pests Consentration Weight 0.50 percent is recommended one litre

6 chemical emulsion dillute with 39 liter of water will give. Total dillute 130.30

concrentration will be 40 litre inclusive of one litre chemical emulsion

appication 0.5 Litre chemical / Sqm of surface is recommended as per I.S.

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6-

hand broken stone aggregates 40 mmnominal size) and curing complete

excluding cost of formwork in (A) Foundation

Providing and laying controlled cement concrete M-250 and curing complete

including the cost of form work but excluding the cost of reinforcement for

8 reinforced concrete work in foundation footings, base of columns and mass 19.80

Providing and laying controlled cement concrete M-250 and curing complete

including the cost of form work but excluding the cost of reinforcement for

9 reinforced concrete work Column Upto Plinth Level 3.80

Providing and laying controlled cement concrete M-250 and curing complete

including the cost of form work but excluding the cost of reinforcement for

10 reinforced concrete work Plinth Beam 11.50

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4-

graded stone aggregates 20 mm nominal size) and curing complete including

11 cost of formwork in (A) Plinth Slab 13.50

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

12 reinforced concrete work in R.C.C. pardee 1.30

Providing and laying controlled cement concrete M.200 and curing complete

including the cost of formwork and reinforcement for reinforced concrete

13 work in (D) Columns (more than 10 ton) 20.70

Providing and laying controlled cement concrete M.200 and curing complete

including the cost of formwork and reinforcement for reinforced concrete

14 work in (D) Columns (more than 10 ton) 5.70

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

15 reinforced concrete work GF Beams 8.90

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

16 reinforced concrete work First Floor Beams 6.00

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

17 reinforced concrete work Lintel & coping G.F. 8.10

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

18 reinforced concrete work Lintel & coping F.F. 2.30

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

19 reinforced concrete work Ground Floor Slab 12.40

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

20 reinforced concrete work First Floor Slab 8.50

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

21 reinforced concrete work in Staircase for Ground Floor. 1.70

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4-

graded stone aggregates 20 mm nominal size) for reinforced concrete

Chhajjas not exceeding 12cm. thickness upto floor two level including

22 finishing the exposed surfaces with cement mortar 1:3 (1-cement, 3 Fine 4.30

sand) to give a smooth and even surface centering and formwork and curing

complete excluding cost of reinforcement.

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

23 reinforced concrete work in R.C.C. pardee 9.50

Providing TMT Bar FE 500D/550D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level.

Providing TMT Bar FE 500D/550D reinforcement for R.C.C. work including

bending, binding and placing in position complete Above floor two level.

Brick work using common burnt clay building bricks having crushing strength

not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1-

26 Cement : 6 -fine sand)(B) Conventional 14.10

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

27 floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b) 72.80

Conventional G.F

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

28 floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b) 26.70

Conventional First floor

Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg./Sq.cm.. In cement mortar 1:3 (1cement :

29 coarse sand) in super structure above plinth level 23.10

Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg./Sq.cm.. In cement mortar 1:3 (1cement :

30 coarse sand) in super structure above Floor Two level 10.10

Providing and fixing 35 mm thick factory-made solid core flush door single

shutter conforming to IS:12823, Grade-I, Type-I, melamine faced with

decorative laminate on both sides and 12 mm thick teak wood lipping on all

31 edges, including approved hinges, aldrop, handles and fittings, complete as 15.00

directed by Engineer-in-Charge.

Providing and fixing FRP frame size 125x65 mm and 35mm thick FRP shutter

having extra reinforcement on sides & edges in polish finish. The core of the

shutter & frame is to be filed up with injected polyurethene foam done in

situ alongwith embedded wooden pieces for stiffening & also taking hinges &

32 fintures. The whole FRP frame & shutter is to be water proof weather proof, 15.40

termite proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S

hinges with necessary screws & alluminium S.S fixtures & fastenings &

fastener sleeve.

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 127mm x 38.10mm x 1.35mm @wt. 1.384kg/m,

horizontal Four track (3 Shutter + 1 Mosqito Net Shutter ) member size

122.20mm x 31.75mm x 1.10mm@ wt 1.205 kg/m, vertical member of size

122.20mm x 31.75mm x 1.50mm @1.398 kg/mt with sliding shutters of

33 horizontal member size 40mm x 18mm x 1.29mm@ 0.456kg/mt ,vertical 21.60

member of size 40mm x 18mm x 1.29mm @ 0.456 kg/mt with 5 mm thick

transparent bronze colour tinted float glass with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass fixing to frame as

per details etc complete for window.

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 95mm x 24mm x 1.17mm @ wt.of 0.738 Kg/mt

horizontal Three track (2 Shutter + 1 Mosqito Net Shutter ) member size

92mm x 31.75mm x 1.30mm,@ Wt.1.07 Kg/mt , vertical member of size

92mm x 31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with sliding shutters of

34 horizontal member size 40 mmx18mm x1.29mm @ wt.of 0.456 Kg/mt, vertical 2.70

member of size 40mm x 18mm x 1.29 mm @ wt.of 0.456Kg/mt/ with 5 mm

thick transparent bronze colour tinted float glass with powder coated

aluminum fittings and fixtures and transparent silicon sealant glass fixing to

frame as per details etc

Providing and fixing standared extruded of alluminium section of size 63mm x

38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with colour anodized alluminium

35 frame for ventilation with 5 mm thick frosted glass as details etc complete 2.40

for Ventilation

Providing and fixing Safty grills of required pattern for Windows / Door using

16 mm dia M.S polished bars and Rectangular CRC pipes of size 50 * 30* 2mm

at Requuired spacing as per design and hold fasting with coach bolts including

one coat of primer and two coats of mattfinished oil painting etc complete.

P & L 24" x 24" Double Charged vitrified 8-10 mm thick tile flooring over

mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

37 dismentaling of existing flooring and jointed with color cement slurry 116.00

including finised with flush pointing & cleaning the surface etc. complete

(10% DARK COLOUR TILES)

P & L 24" x 24" Matt Finished Glazed vitrified 8-10 mm thick tile flooring over

20 mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on

38 new surface or fixing on existing flooring by adhesive material including 11.00

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc. complete

Providing and laying Porcelain tiles 6mm thick in flooring laid on a bed of

12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with

39 flush pointing in white cement & providing neccessary groove & filling with 12.60

epoxy adhesive etc. complete.

Providing and laying Digital Printed glazed tiles 6mm thick in dado on 10mm

thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white

40 cement slurry & providing neccessary groove & filling with epoxy adhesive 99.90

Providing and laying polished Kota stone slab flooring over 20mm (Average)

thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-

Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry Sq.Mt.

mixed with pigment to match the shade of slab including rubbing and

polishing etc. complete. (A) 25mm thick

Providing and laying Granite Stone slab 25 mm ( Average ) thick incl. Full

molded round front edge laid on 15 mm thick cement mortar 1:3 (1- cvement

42 : 3 coarse sand ) jointed with grey cement Slurry including rubbing and 15.70

polishing etc. Complete

Providing and laying broken chine mosaic flooring for terrace using

mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar

1:3 to plain or slope and to be tempered to bring mortar creme out upto

43 surface using white cement including rounding off junctions and extending 127.00

them upto 15 cm along the wall,clearing with water and oxalic acid etc. as

Providing and laying mirror polished Black Granite stone slab 18 mm (

Average )thick (Shade of Black Granite Aprooved by Engineer in Charge incl

adhesive used with Sand for Proper Joint with Wall With. Full molded round

44 front edge laid on 10 mm thick cement mortar 1:3 (1- cement : 3 coarse sand 64.00

) jointed with grey cement Slurry including rubbing and polishing etc.

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of

single or half brick walls for interior plastering upto floor two level and

45 finished even and smooth in (ii) Cement mortar 1:6 (1-cement :6-sand) for 289.00

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of

single or half brick walls for interior plastering upto floor two level and

46 finished even and smooth in (ii) Cement mortar 1:6 (1-cement :6-sand) for 160.00

Providing 10 mm. Thick cement plaster in single coat for plastering on

ceiling and soffits of stairs upto floor two level and finished even and

47 smooth in : (I) Cement mortar 1:3 (1 cement : 3 sand) Ground Floor 97.70

Providing 10 mm. Thick cement plaster in single coat for plastering on

ceiling and soffits of stairs upto floor two level and finished even and

48 smooth in : (I) Cement mortar 1:3 (1 cement : 3 sand) First Floor 60.90

20mm thick sand faced cement plaster on walls upto height 10 metres above

ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

49 sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc & 443.70

providing 10 mm Grooves as per Drawing complete.

20mm thick sand faced cement plaster on walls upto height 10 metres above

ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

50 sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc & 13.70

providing 10 mm Grooves as per Drawing complete. with grooves.

Providng and applying two coats acrylic lappy (putty) and two coats of primer

& Wall painting ( two coats) with plastic emulsion paint of approved brand

and manufacture on wall surfaces to give an even brushing the surface free

from mortar droppings and other foreign including Wall painting (two coats)

51 with plastic emulsion paint of approved brand and manufacture on 449.00

undecorated wall surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign matter and sand

papered smooth.

Providng and applying two coats acrylic lappy (putty) and two coats of Primer

Wall painting ( Two coats) with plastic emulsion paint of approved brand and

manufacture on ceiling & sofit to give an even brushing the surface free from

mortar droppings and other foreign including Wall painting (two coats) with

52 plastic emulsion paint of approved brand and manufacture on undecorated 159.00

wall surface to give an even shade including throughly brushing the surface

free from mortar droppings and other foreign matter and sand papered

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

53 brushing the surface to remove all dirt, and remains of loose powdered 989.00

materials etc complete

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe (

SCH- 40) for cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C

54 or shall be concealed as directed including necessary fittings etc. including 42.00

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe (

SCH- 40) for cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C

55 or shall be concealed as directed including necessary fittings etc. including 15.00

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR

13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water

56 of following dia. nominal bore tube fittings and clamps including making good 8.00

the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe (

SCH- 40) for cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C

57 or shall be concealed as directed including necessary fittings etc. including 50.00

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing and fixing heavy Handle valve of aprroved brand & Following

internal dia of brass including fixing in pipe lines etc.complete © 25 mm dia

Providing and fixing heavy Handle valve of aprroved brand & Following

internal dia of brass including fixing in pipe lines etc. Complete (E) 40 mm Dia

Providing and fixing Sluice valves IS 14846 with ISI mark of Approved Brand &

Follwing internal dia including fixing in pipe lines 40mm

Providing and fixing to wall, ceiling and floor galvanised mild steel tubes

(Medium grade) of the following nominal bore, tube, fittings and clamps

included making good the wall, ceiling and 40mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure

polythene pipes of the following outside Dia. Low densidy, complete with

62 special falnge compression type fittings, wall clipsetc. including making good 50.00

the wall ceiling and floor.(F) 75mm

Providing laying and jointing in true line and level 110 diameter

U.P.V.C. SWR Type B pipe confirming to IS 13592-1992 with one end plain

63 and other end socketed with rubbering, & fitting 110mm 202.00

Providing and fixing PVC SWR Nahni Trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing design

64 with C.I. screwed down or hinged grating 6.00

Providing and fixing Screw down Quarter turn bib taps of following size

(A) Brass chromium plated screw down Bib tap (I) 15 mm dia

Providing and fixing CP brass Quarter turn pillar tap, capstan head

screw down high pressure with screw, shanks and back ndts (A) 15 mm dia

Providing and Fixing wash basin with pedestal of std. Height with single hole

for pillar tap with C.I or M.S brackets painted white including cutting cutting

67 holes and making goods the same include C.P brass Waste and Waste pipes 3.00

(A) Vitreous china.

Providing and fixing SS Sink Glosy ASIS 304 Grade × 100 thick with over all size

610 × 460 mm & bowl Size 560 × 410 × 200 with single hole for pillar tap

Fixing in sanwhich platform including cutting holes and making goods the

same including . necessary Fixture, connections and waste Pipes.

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size

580mm (Earthwork, bed concrete, foot reste and trap Including. (I) Long

69 pattern = White colour 1.00

Providing and fixing wash down water closet (Europen type W.C.Pan) with

integral"P" trap including jointing the trap with soil pipe in cement mortar 1:1

(1-cement, 1-sand) of Hindware Wall Hung Water Closet 92055 has a slow

falling seat cover with an antibacterial and germ free ceramic surface.

with a water saving dual flush. and including jet spray operated with

necessary valve of Jaquar / Cabtree / Plumber including cutting holes in

walls and making good the same connecting the flush bend with cistern and

closet vitreous china etc. complete.

Providing erecting and fixing double coated Syntex or equivalent

PVC. (ISI) mark water tank of reqd capacity each with all necessary

71 fittings & connection etc. comp on terrace. 3000.00

Providing and fixing 600 mm x 450 mm bevelled edge mirror of superior

glass mounted on 6 mm thick A.C sheet or plywood sheet or PVC framing and

fixed to wooden plugs with C.P brass screw abd washers.

Providing and fixing C.P. brass towel rail complet with C.P. brass brakets

73 fixed to wooden plugs with cpbrass screws ( B ) 600 mm X 20mm size 4.00

Providing, supplying and fixing concealed single lever CP brass shower mixer

with 200 mm overhead shower rose, riser/shower arm, hand shower with

m flexible hose & holder, angle valves, all necessary CP fittings, 15 mm piping

74 up to 3 m, cutting & chasing in tiles, sealing & testing, complete in all 3.00

respects — per set.

Constructing brick masonary chamber for under ground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in cm. 1:5 C.I. Cover with frame (light duty) 455 mm. X 610 mm.

Internal dimensions, total weight of cover with frame to be not less than

Kgs. weight of cover 23 Kg. and wt. of frame 15 Kg) R.C.C. top slab with

1:2:4 mix(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm.

size ) foundation concrete 1:5:10 inside plaster 15 mm. thick with cement

mortar 1:3 finished smooth with a floating coat of neat cement on walls &

bed concrete etc. complete.

(I) inside dimensions, 455 mm. x 610 mm. And 450 mm. Deep for single

Providing and fixing in position Name Plate as directed by Engineer-in-charge

with all necessary tools & plants etc. complete.

Providing and fixing “Sandwich Platform” type kitchen platform with bottom

support slab and top slab, made of 18–20 mm thick machine-cut, machine-

polished Granite stone slabs of approved shade and colour, including vertical

77 fascia, edge moulding, cutting for sink/hob, making necessary openings, and 4.00

providing nosing wherever required, fixed in position with cement mortar 1:4

and approved stone adhesive (epoxy/resin based), complete in all respects.

Providing and fixing C.I. Manhole cover 0.60m x 0.45m size having weight not

less than 35 kgs.

Providing and fixing chiken mesh jali with square of 12.50 X 12.50 mm of

gauge at junction the Brick masonary and reinforcement concrete member

including fixing materials sacffolding labour etc.complete

Providing and fixing Stainless steel railing made from anticorrocive 304 grade

S S pipe of 50 mm dia (16Gauge) as hand rail with 38 mm dia pipe for suports

80 at 1.2 mt Vertical supports at eqal distance fixed in RCC Railing including 12.00

accessories as per detailed drawing as directed

Providing and constructing flower bed of including excavation if required,

PCC 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm

nominal size) as base, brick masonry in cement mortar 1:6 for sides, internal

plaster 12 mm thick in cement mortar 1:4, finished with neat cement

punning, filling with good earth brought from outside, watering, ramming,

dressing, and finishing complete in all respects as per direction of Engineer-in-

Providing throating or plaster drip and moulding to R.C.C. Chhajja.

Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar

1:1 including neat cement finishing, watering etc. complete.

Providing and filling screened of burnt coal cinder including and consolidation

Providing 20mm thick cement plaster in single coat on Sunk Slab, finished

even and smooth with a floating coat of neat cement slurry, providing

necessary Slope & also waterproofing the surface etc. Complete Directed by

engineer in Charge in (iii) Cement mortar 1:6 (1-cement:6-sand)

Providing and fixing heavy duty roof access ladder fabricated from M.S.

sections, overall size 0.60 m wide × 3.15 m high, comprising side runners

made out of M.S. flat/bar/pipe sections and ladder rungs/steps placed at

0.30 m centre to centre spacing, including necessary bends, brackets, cleats,

holdfasts, anchor fasteners, welding, cutting, grinding and fixing complete as

per approved design and direction of Engineer-in-Charge. The ladder shall be

securely fixed to wall/slab/structural member with necessary M.S. supporting

brackets and hardware, finished with one coat of red oxide zinc chromate

primer and two coats of synthetic enamel paint of approved shade and make,

complete in all respects.

Providing and fixing 25 mm thick approved quality machine-cut Kota stone

slab shelf of size 3.50 m × 0.45 m, cantilevered from masonry wall, with

minimum 100 mm bearing embedded into wall pockets at ends and supported

on concealed M.S. angle brackets (40×40×5 mm or as approved) securely

anchored to the wall. The stone shall be fixed using cement mortar 1:3 and

87 non-shrink grout in pockets, including cutting chases, making good the 3.20

disturbed masonry/plaster, dressing and polishing exposed edges, filling

joints, curing, red oxide priming of steel supports, and all labour, materials,

tools and incidental works complete as directed by the Engineer-in-Charge.

Providing and fixing approved quality polished granite shelf of size 150 mm

wide × 300 mm long and 18–20 mm thick, fixed in masonry wall with cement

mortar 1:3 and non-shrink grout wherever required, including cutting

88 pockets/chases in wall, dressing and polishing exposed edges, making good 0.40

damaged plaster, curing, cleaning, and all labour, materials, tools, and

incidental works complete as directed by the Engineer-in-Charge.

Box cutting the road surface to proper slope and camber for making a base for

road work including removing the excavated stuff and depositing on the road

side slope as directed upto 50Mt.lead.

Providing, laying, spreading and compacting stone aggregates of 63 to 45mm

sizes & Stone screenings Type-A for WBM Grade-II, as per specification

including spreading in uniform thickness, hand packing, rolling with smooth

wheel roller 80-100 kN in stages to proper grade and camber, applying and

90 brooming, stone screening/binding materials to fill-up the interstices of 9.00

coarse aggregate, watering and compacting to the required density grading

as per Technical Specification Clause 405. By Manual Means

Providing and cast in situ Vacuum De-watered Unreinforced cement concrete

of grade M-20-Trimix flooring for average wearing coat / C.C. pavement laid

as directed in approved fixed side form work of steel channel including

vibrating by screedneedle vibrator and leveling with trimix, surface vibrator,

Vacuum De-watering with trimix vacuum pump, floating and further

compaction with trimix skin floater equipped with floating disc, and finished

91 in continous operation including cutting the concrete with concrete cutting 10.00

machine for contraction joints at every 4.00 mtr and expansion joint at

interval of 40 mtr of size 6x12mm to 12x25mm deep or as specified /

providing stripped / broom finish evenly, applying debonding strips, bitumen

primer,bituminous sealant,12 mm dia jute rope and curing etc. complete.

Providing and fixing pre-cast concrete kerb stone of gray cement based

concrete block 30cm length,30cm height and 15cm thick of M250 grade

concret as per approved design and including excavation for fixing in proper

line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Providing and laying bedding layer of well-graded grit (4.75–6.00 mm size)

over prepared surface to a compacted thickness of 25–40 mm, including

spreading to the required grade and camber, rolling with vibratory plate

compactor or road roller in static mode, watering and consolidating the

surface, laying of paver blocks to the proper line and level, filling joints with

93 clean dry fine sand by brooming, and compacting the laid surface with a plate 115.00

vibrator to seat the blocks and fill joints completely, including cost of all

materials, labour, tools and plant, complete as per MoRTH Clause 1500/1700

and the direction of the Engineer-in-Charge.

Providing and fixing pre-cast Rubber Dye / Steel dye inter locking concrete

block 60mm thick with grade of concrete M30 pnumatic compressed/ vibrated

mechanically and as per approved design Confirming to IS 15658:2006

94 including 35mm Sand layer for levelling and filling the joint with sand in 58.00

proper line and level as per Guideline of IRC :SP 63-2018 etc complete.

20mm thick sand faced cement plaster on walls upto height 10 metres above

ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

95 sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. 531.00

Providing and fixing M.S. Main Entrance Gate of overall size 3.60 m × 1.80 m,

fabricated from M.S. square hollow sections of suitable sizes for outer frame

and internal stiffeners, incorporating horizontal M.S. rectangular hollow

section slats and diagonal members as per approved design and drawing,

including cutting, welding, grinding, hinges, locking arrangement, tower

bolts, holdfasts, all necessary fittings and fixtures, complete erection in

position, surface preparation, one coat of red oxide zinc chromate primer and

One coat of approved enamel paint of required shade, complete in all

respects as directed by the Engineer-in-Charge.

Providing and fixing 0.6 metre high fencing over an existing masonry/concrete

wall, using M.S. angle posts of size 40 mm x 40 mm x 6 mm and 2.0 metres

length, spaced at 3 metres center-to-center. The angle posts shall be

securely fixed to the top surface or face of the wall using heavy-duty

expansion or chemical anchor bolts (such as Hilti or equivalent) with suitable

steel base plates or brackets welded/fixed to the posts to ensure firm and

stable attachment.Five horizontal lines and two diagonal lines of galvanized

97 steel barbed wire weighing 9.38 kg per 100 metres shall be strained and 125.40

fastened to the angle posts with G.I. staples. All exposed metal parts

including posts, brackets, and fasteners shall be painted with three coats of

oil-based paint to provide corrosion protection and a durable finish. Work

includes all necessary surface preparation, drilling, fixing of anchors, erecting

posts, tensioning and fixing of barbed wire, and application of protective

painting, complete as per specifications.

Drilling of 200 / 215 mm dia. bore well in over burden rocky or loose

collapsible / boulder strata & lowering of 175 / 200 mm dia. UPVC / PVC /

98 ERW casing pipe above 12 meters and up to 40 meters depth by DTH rig 25.00

etc.complete For Zone-I

Drilling of 200 mm dia bore hole by DTH rig in rocky formation in All takuka of

Zone III ( o to 350 Mtr )

Supply of "U" PVC Casing pipe CM type (B) 200 mm dia

Providing and fixing bail plug {Bottom Cap } Suitable for 200mm dia. Pipe

Excavation for foundation upto 1.5 Meter depth including sorting out ands

tacking of useful materials and disposing of excavated stuff up to 50 Meter

102 lead. (a) Loose or soft soil 3.00

Providing and laying controlled cement concrete M.200 and curing complete

including the cost of formwork but excludingcost of reinforcement for

reinforced concrete work in (A) Foundations, footings, Base of columns and

Steel work welded in build up sections,framed work including cutting,

hoisting fixing in position and applying a priming coat of red lead paint A) In

beams and joists, channels, angles,tees, flats with connection plates or angle

cleats as in main and cross beams, hip and trussed purlins connected to

common rafters and the like.

Providing corrugated G.I. sheets roofing fixed with galvanized iron "J" or "L"

hooksbolts and nuts 8mm diameter with bitumen and G.I. limpet washers,

filled with white lead complete excluding the cost of purlins rafters and

trusses (1) 0.80mm thick sheet.

Applying priming coat over new steel and other metal surface after over and

including preparing the surface by thoroughly cleaning oil, grease dirt and

other foreign matter and scoured with brushes fine steel wool, scrapers and

106 sand paper with ready mixed priming paint brushing red lead. 33.00

Painting two coats (excluding priming coat) on new steel and other metal

surfaces with enamel paint brushing, interior to give enamel paint brushing,

107 interior to give an even shade including cleaning the surface of all dirt, dust 37.80

and other foreign matter.

Providing and supplying sofa(2seater) made with using 19mm Thk. Plywood

(M1) structure frame with S.S. legs required necessary support fixed with

necessary fixtures and fastening (Hardware)(M14). It shall be covered with

Density PU foam(M22) with required Thickness as per design in seat & back

and handle portion this should be again covered with 14 mm thick PU foam

108 (M22) with Madarpat cover on it & upholstered fabric(M26) or leather of 2.00

suggested & approved by architect finished with seat, back & all visible side

as per architect drawing. Complete as per architect's drawing and as per

instruction of architect & engineer in charge.

Providing and supplying Centre Table 900 X 600 X 400 with Glass top, made

with 19mm Thk. Plywood (M1) finished with 1.0 mm Thk. decorative laminate

sheet (M24) specified and approved by architect & fixed with necessary

fixtures and fastening (Hardware) (M14) inclusive of approved melamine

109 polishing (M29) work. Top part of center Table covered with 12 mm Thk. 1.00

toughened Glass (M27) with Polished Edges. Complete as per architect's

drawing and as per instruction of architect & engineer in charge.

Providing and supplying Corner Table/Tipoi 600 X 600 X 400 with Glass top

made with 19mm Thk. Plywood (M1) finished with 1.0 mm Thk. decorative

laminate sheet (M24) specified and approved by architect & fixed with

necessary fixtures and fastening (Hardware) (M14) inclusive of approved

110 melamine polishing (M29) work. Top part of center Table covered with 12 mm 2.00

Thk. toughened Glass (M27) with Polished Edges. Complete as per architect's

drawing and as per instruction of architect & engineer in charge.

Providing and supplying Stainless Steel (SS) push lid dustbin of capacity not

less than 30 litres, fabricated from Grade 304 stainless steel sheet of

minimum 0.8 mm thickness, with cylindrical body, spring-loaded self-closing

push lid, and removable inner container for easy cleaning. The dustbin shall

111 have a mirror/matt finish surface, suitable for indoor use in offices, lobbies, 2.00

or public areas, including all accessories, transportation, handling, and

placement complete as per direction of the Engineer-in-Charge.

Providing, supplying and fixing approved quality L-shaped wardrobe having

overall dimensions 2.00 m length × 2.50 m height × 0.50 m depth,

manufactured from 18 mm thick BWP/BWR grade plywood or pre-laminated

engineered board with 6 mm thick back panel, comprising shutters, shelves,

hanging space, loft storage, drawers and partitions as per approved layout.

The wardrobe shall be finished with laminate on all exposed surfaces and

matching edge banding, complete with one full-height mirror of minimum

mm thickness fixed on wardrobe shutter, SS hinges, telescopic drawer

channels, handles, locks, magnetic catches, tower bolts, screws, adhesives

and all necessary hardware. The item shall include all cutting, fitting,

polishing/laminate finishing, mirror fixing, transportation, installation at site

and all labour, materials, tools and incidental charges required for complete

execution of the work, complete in all respects as directed by the Engineer-in-

Providing, supplying and placing approved quality 6-seater dining table set

comprising one dining table of size 1.80 m × 0.90 m × 0.75 m height and six

matching chairs, manufactured from seasoned hardwood, engineered wood,

or equivalent approved material, with table top finished in laminate, veneer,

glass, or polished finish as approved. The chairs shall be provided with

cushioned seats and backrests upholstered in approved fabric/leatherette,

113 complete with all fittings, fasteners, accessories, transportation, loading, 1.00

unloading, handling, assembly, and placement at the designated location.

The item shall include all labour, materials, taxes, and incidental charges

required for complete installation and commissioning, complete in all

respects as directed by the Engineer-in-Charge.

Providing and supplying a double bed (1800 mm × 2000 mm) made of BWP

grade plywood (IS:710) with minimum 19 mm thick structural members and

mm panels, treated for anti-termite and anti-borer, designed as a box-type

storage bed with top opening. The bed shall be fitted with heavy-duty

hydraulic gas lift mechanism (120 kg capacity) with powder-coated MS frame

for smooth and durable operation. Storage box shall have 12 mm bottom

panel with proper support and ventilation. The bed shall include a full-height

headboard, finished with 1.0 mm laminate and PVC edge banding. All fittings Nos.

including SS hardware and branded hydraulic system (Ebco / Hettich) shall be

provided complete. Providing and placing a 6-inch thick mattress (1800 mm ×

2000 mm) made of 40 kg/m³ high-density foam with premium fabric finish.

Including transportation, loading-unloading, and installation complete as

directed by the Engineer-in-charge.

Providing and supplying a bedroom wardrobe of size 2.50 m (H) × 2.50 m (W)

× 0.50 m (D) made of BWP grade plywood (IS:710) with 19 mm thick structural

members and 12 mm internal panels, treated with anti-termite and anti-borer

chemicals. The wardrobe shall be provided with 4 hinged shutters, finished

with 1.0 mm laminate on external surfaces and internal surfaces finished with

white laminate, with edges sealed using PVC edge banding. One shutter shall

be provided with a full-length 5 mm thick mirror, properly fixed with backing

support and edge protection. The unit shall include internal arrangement with

hanging space with SS rod, adjustable shelves, minimum 2 drawers, and loft

storage at top level. Back panel shall be 6 mm BWP plywood, properly fixed.

The wardrobe shall be securely fixed to wall using anchor fasteners / cleats,

ensuring full-height stability and alignment. All fittings including SS soft-close

hinges, handles, locks, drawer channels, and branded hardware (Ebco /

Hettich) shall be provided complete. Including transportation, loading-

unloading, assembly, and fixing to wall in position complete as directed by

the Engineer-in-charge.

Providing, supplying and placing approved quality 3-seater sofa of size 2.10 m

(L) × 0.90 m (D) × 0.85 m (H) for drawing/living room use, fabricated with

sturdy hardwood/engineered wood frame, high-density foam cushioning in

seat and backrest, upholstered with premium quality fabric/leatherette of

approved colour and texture, complete with armrests, base supports/legs, all

116 necessary fittings and accessories, including transportation, loading, 1.00

unloading, handling, placement at the designated location and all labour,

materials, taxes and incidental charges, complete in all respects as directed

by the Engineer-in-Charge.

Earthwork for embankment including breaking clods, dressing with all lead

and lift (excluding watering and consolidation) (E) From Borrow area within

117 3.0 Km. lead (more than 10 ton) 3630.47

Rolling of earthwork in layers with power roller including filling in depressions

118 which occur during the process. (more than 10 ton) 3630.47

Watering of earth work as directed.

Providing and filling in foundation with ordinary Cement concrete M-150 mix

and providing necessary vertical pin headers including formwork, vibrating,

120 ramming and curing complete. 38.00

Providing and casting in situ controlled cement concrete M-250 for R.C.C.

Retaining wall as per drawings including centering shuttering, scaffolding

121 where necessary, laying vibrating, curing and finishing complete.(A) Height 120.00

from 0.0 to 5.0 M. (1) Retaining wall

Providing and laying in position FE 500D TMT bar reinforcement including

cutting, bending, hooking and tying complete as per detailed drawings for the

following.(C) R.C.C. Retaining wall

Providing and laying wheep holes in abutment and returns by using P.V.C.

pipes of 100 mm dia laying in proper grade and joining etc. complete as per

123 detailed specifications. 100.00

Providing and laying - Fitter Media 600mm thick directed at the back of

abutments, returns and wing walls as per detailed specifications.

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 kV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured/metallic/white front plate modules erected on

/ in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete, Cat. III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of .ISI marked 1.1 kV Grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected with 6A Modular

type switch and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (f)

with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete, Cat. III

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as

127 per site situation directed by Engineer In charge. (7) Blank Plate Single, Cat.III 25.00

(9) 16 Amp. SP one way switch, Cat.III

(10) 6/16Amp. Universal socket, Cat.III

(4) TV Co-axial Socket outlet, Cat.III

(21) Foot Light as per colour requirement with concealed box, modular

accessories, acrylic glass cover with suitable LED watt with all accessories as

per following module, (a) Two modules

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules erected on / in

wall / ceiling with following type accessories, Cat. III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (green) both are of .ISI marked 1.1 kV grade FRLS PVC

insulated multi strand copper wires erected in below type of pipe with 6A

Modular type switches and following type of accessories erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate modules erected on / in wall / ceiling as per pipe

erected. with necessary batten/angle holder or ceiling rose or H.D.Connector

as directed. (f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete, Cat. III

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following

size complete to be erected on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & Clamps with following

134 dia of pipes, in approved manner as directed , (a)20 mm 48.00

Providing and erecting Mains with 1.1 kV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor

135 FRLS PVC insulated stranded wire of green colour for earth continuity of 300.00

following size, (A) With medium class Rigid PVC pipe and accessories, (b)

wire 2.5 sq. mm

providing and erecting Mains with 1.1 kV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected in /

on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size, (A) with

medium class Rigid PVC pipe and accessories, (A) with medium class Rigid

PVC pipe and accessories, (a) 2 wire 4 sq. mm

(i) 4 wire 10 sq. mm

(use earth wire of 4 sq.mm )

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kV

grade ISI marked copper wires of following size to be erected as directed. (e)

138 1.50 Sq.mm 3 core round PVC sheathed 35.00

Providing & Erecting approved make following size of TV Co-axial flexible

cable comprising inner conductor of solid bare copper insulated with Foam PE

139 & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ 60.00

suitable coverage overall sheathed with black PVC insulation. (e) RG-11

Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

Decorative call bell Ting-tong box type 250 volts complete erected

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

142 LED driver efficiency > 85 % 4.00

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)(A) Tube Light with

integral driver, (i) 5-10 Watts, Surge-2 kV, IP-20, conventional 1 to 2 feet,

(v) 36-40 Watts, Surge-2 kV, IP-20, conventional 4 feet, Cat-lll

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure

die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

144 LED driver efficiency > 85 % 29.00

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)(A) Square/ Circular

shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20, (iii) 16-20 watts, Surge-2 kV, Cat-lll

(H) Mirror Light 9 Watts, wall mounted minimum 1 feet long

Supply & fixing decorative Hanging light with glass having cylindrical or

square shape having length not less than 10" & width not less 3.5" with

holder, lead wire as per required length but not more than 1mm & base plate

for fixing the fitting with ceiling.[a] suitable for led lamp, Cat-III

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

147 >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( 4.00

fittings required LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (A) Street Light (IP-

65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection. (ii) 48 - 59 Watts, Cat-lll

(B) Flood Light (IP-65), Surge protection -4kV integral and ,Light must have

440VAC line supply with over-voltage protection. (iv) 90 - 119 watts, Cat-lll

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and

spun aluminum canopy fixed with opal polycarbonate, pipe arrangement for

149 vertical mounting driver and accessories wired up to terminal block.IP 65, 2.00

(ii)32-40W, Cat-lll

Supplying KITKAT pattern porcelain cut-out fuse with base of following

current capacity erected on existing block board. (iv) 63 A 500 V

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable

to operate on 240 V A.C. system and having breaking capacity 10 KA to be

151 erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III, 36.00

Providing & erecting 240 V MCB double pole switch for motor & inductive load

(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing

152 box having following capacity (A) 6 to 32 Amp. Cat.III 2.00

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve)

having 10 KA breaking capacity & confirms to IS : 8828 in existing box having

153 following capacity, (A) 6 to 32 Amp. , Cat.III 2.00

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

154 having following capacity (c)63 Amp. Cat.III 2.00

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of MCB to

be used) suitable for, (B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI) (b) sheet steel double door, (ii)6

providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz. having characteristic of

157 quick action & tripping with all advance feature & do not incorporate any 3.00

electronic component. for following Max. rating erected as directed, (i)

Amps.DP Cat. III

(ii) 40Amps. DP , Cat. III

Providing and erecting Annealed bare Copper wire 4.064mm to 1.626mm.

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms.

dia. galvanised iron pipe with coupling and buch buried in specially prepared

160 earth pit complete with necessary 8 SWG earth wire. 2.00

For using salt and charcoal / coke as required for pipe type earthing.

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover. (A)(approved make OEM has to submit test certificate including value

of earth resistance of installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing resistane mentioned in

test Certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back

fill Compound :- Earthing compound should be capable to retain moisture for

long time Necessary test report must be submitted by Agency. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI armoured cable Aluminium

conductor for 1.1 kV. to be laid on wall with necessary clamps or in existing

163 trench / pipe of following size of cables. (B) 2 core 6 Sq. mm 370.00

Making trench in soft soil of suitable width of 90 cm deep for laying cable or

locating the fault all over the run and back filling the same and making the

164 surface as normal ground. 155.00

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting

165 accessories of same material at required depth in existing trench for laying 170.00

of cable. below ground / road surface for enclosing cable (A)50 mm outer dia

Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3) as

per IS:4984:1995 PE-80 to be erected at road crossing on or floor as directed

166 for laying of cable. The pipes as following size of dia & weight per 6 mtr. (A) 55.00 Ea.

40 mm inner Dia.

Providing and erecting Approved make Ceiling fan with double ball bearing ISI

mark with condenser A.C. 230V.50 Hz.1200 mm. sweep complete, canopy

167 erected on existing hook or clamp with earthing. [Make shall be approved by 9.00

Engineer in charge]

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab

with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the

RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S.

169 box / Heavy Duty PVC box complete erected concealed in Ceiling with 9.00

necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan

Supplying & erecting approved make low noise decorative exhaust fan having

square frame ABS body with inbuilt lowers & square frame. 250mm with

171 RPM Cat.II 3.00

Supplying and erecting approved make Octagonal pole made from HR sheet

steel. The pole should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm Hylam sheet,

standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal

and arrangement for cable termination to be erected With Suitable

foundation (Included) as per details given by manufacturer considering site

requirement. (C) 5 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M16 Bolts and 600mm

long with necessary G.I. J Bolts .Approx Pole weight 46 kg

Supplying & erecting approved make SMC press moulded composite FRP.

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as per

173 requirement having locking arrangements with mounting clamp with nuts, 4.00

bolts & washers suitable for erection on pole with cable clamps& earth bolt

of following size of box. (C)150mm x 125mm x 100mm [deep]

Supplying and erecting Street light pole bracket comprising main B Class MS

pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S.

sleeve tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and bolts for fixing the

174 brackets and having spread of 0.5 mtr. Length with 110 deg.with vertical 3.00

plane and suitable welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base primer and two coats

of Aluminium / PU paint. paint with following nos of arms. [B] Double Arm

Bracket 0.5 Mtr

Supplying and erecting B class Galvanized iron pipe having smooth finished

bore of the pipe on both ends erected nuts and bolts along the pole / wall

175 shaping the pipe as per site requirement. Pipe dia as following. (B) 32 mm dia 5.00

Supplying and erecting Direct - On - Line Starter with 18 A. rating contactor

and with 3.5 Amp. 18A range directly operated in totally insulated elegant

176 enclosure for single phase operation up to 3 HP as per IS 13947 complete 2.00

erected on P.W. Block with necessary connection. Cat-lll Ea

Providing & erecting open well type horizontal mono block pump set with

stainless steel body having following specification, (D) 1 HP Three phase

177 open well motor pump set suitable for 190 LPM discharge @ 21 mtr. head, 1.00

suitable for 32mm dia. delivery pipe. Cat. II

S.I.T.C. of single phase submersible pump set suitable for 100 mm size or

more dia bore well having motor capacity and discharge as under with

178 necessary panel box. Lifting and Lowering taken extra. (b) Motor rating 1.5 1.00

HP (16 stage) pump having capacity of 50 LPM at 60 mtr head suitable for

mm dia. delivery pipe, Cat.II

Lowering of submersible motor pump set at the depth of following ,complete

with required. Nos. and size of casing pipes erected by means of proper chain

pulley block & pipe wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe assembly filled up with

water (A) Up to 60 mtrs.

(D)For Open well Horizontal submersible pump set for sump well, (i) 1 HP

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible

Submersible copper cable approved make of following Size. (B) 3 Core x

Providing Water proof straight Joint in PVC insulated flat flexible copper

cable by using insulating material, water proofing material, & making the

182 joint complete. (A) Up to 10Sq. mm 2.00

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no

extra payment shall be made.

The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

GST and Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C

All Date:11/05/2017

work shall be carried as stated

out as per P.W.D. in Book

therefore in R.C.C. items

other specification where

Division orisasa directed.

change as per actual mix design the

All the columns in the Schedule be filled in ink and the total of the entries in the last column should be struck by the contractor under

Rates quoted include clearance of site (prior commencement of work and at its close) in all respects and hold good for work under all

conditions, site moisture, weather etc.

The contractor shall exhibit the details of work, tender amount, specifications as per Govt. circular No. BDG / 3277 / 1657 Dated. 26-4-

1978 and G.R. No. TNC/ 1090-24 C, Dated. 18-11-91 as directed by the Engineer-in-charge on the work site for which contactor

In R.C.C. item where there is change of grade mix orchange as per actual mix design the difference of of cement consumption shall be

added / deducted from rate of original item at the rate of star rate mentioned in the tender.

For earthquake resistance provision the works shall be carried cut as per the intruction of Engineer in charge.

The other conditions of Schedule "B" will remain unchanged.

Testing of materials shalll be as per statement atteched with the specification. The materials shall be tested in G.E.R.I. bill of testing

charges shall be paid the Executive Engineer and 1 % of the amount put to Tender shall be recovered from the contractor in running bills

is as per G.R. (R&B) Dept. No. TNC 1085 / (4) C Dt. 10-05-85.

Contractor shall even 'NIL' percentage. If deduction is offered.

Deputy Executive Engineer Executive Engineer

( R & B) Sub Division (R & B) Division