CONTRUCTION OF COW HOUSE BOUNDRY WALL RESIDENCY and REMAIN WORK JHARIPANI ROAD NEAR PRIMARY SCHOOL AT NAGAR PALIKA MUSSOORIE

Earth work in excavation by mechanical means (Hydraulic Excavator) /manual means over areas (exceeding 30 cm in depth, 1.5 m width as well as 10 sqm on plan) including getting out and disposal of excavated eath lead upto 50 m and lift upto 1.5 m, as directed by 2.6.1 all kinds of soil.

4.1 Providing and laying in position cement concrete of specified grade excluding th cost of centering and shuttering all work uo to plinth level :4.1.8 1:4:8 (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40mm nominal size)

5.15 Providing, hoisting and fixing above plinth level uo to floor five level precastreinforced cement concrete in lintels, beams and bressumers, including setting in cement motar 1:3 (1 cement : 3 coarse sand), cost of requiredcentering and shuttering but, excluding the cost of reinforcement, with 1:1:2 (1 cement :1.5 coarse sand (zone - III) : 3 graded stone aggregate 20 mm nominal size)

5.9.6 Columns, Pillars, Piers, Adutments, Post and Struts

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes (weepholes)

5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level 5.22.6 Thermo Mechanically Treated bars of grade Fe - 500 D or more.

6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

12 mm cement plaster of mix in 1:6 (1 cement : 6 fine sand) (13.1.2) DSR-

1.4 rndom Rubble Stone Masonry laid in 1.6 cement and sand mortar, inbreast walls, retaining walls, parapets, scuppers, etc. including supply of all material, labour, T&P and royaltiles etc. complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203 of MORDSpecification (Rate 4080.40=4080.40*.12=489.65=4080.40+489.65=4570.05)

10.25 Steel work welding in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 in gratings, frames, guard bar, ladder, railings, brackets, gatesand similar work

9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) .9.1.2 Sal wood

9.20 Providing and fixing ISI marked flus door shutters conforming to IS : 2202 (part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vetical grains or cross bands and face veneers on both faces of shutters 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing 1st qualiity ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades excepts burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete DSR

13.61 Painting with synthetic enemel paint of approved brand and manufacture to give an even shade: 13.61.1 Two or more coats on new work

13.48 Finishing with Deluse Muili surface paint system for interiors and exteriors using Primer as per manufacturers specifications :13.48.3 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture.

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth level :4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

4.11 Providing and laying c.c floor 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

16.70 Providing and fixing G.I chain link squre of required width in mesh size 50X50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. 16.70.2 Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

SANITARY FITTINGS 17.2 Providing and fixing white vitreous china pedestal type water closet (european type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floor wherever required: 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid

17.7 Providing and flxing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : 17.7.2 White Vitreous China Wash Basin Size 630 X 450 mm with a single 15 mm C.P. brass pillar tap

Providing & Fixing of 15mm G.I. class 'B' Pipe (Jindal hissar Make) complete with G.I. fittings & cramps including supply of all materials, labour and T&P etc. and including making good the wall etc. (internal work) as per D.S.R. code no. 18.12.1 15 mm dia nominal bore

18.12.2 20mm dia nominal bore

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and amking necessary holes for inlet, outlet and over flow pipes but without fittings and the base support for tank.

18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :18.18.2 20 mm nominal bore

18.16 Providing and fixing brass stop cock of approved quality 18.16.2 20 mm nominal bore

18.21 Providing and fixing uplasticised PVC connection pipe with brass unions : 18.21.2 45 cm length 18.21.2.1 15 mm nominal bore

18.49 Providing and fixing C.P. brass bib cock of approved quality confrming to IS : 8931 : 18.49.1 15 mm nominal bore

18.53 providing and fixing C.P. brass angle valve for basin mixer and geyserpoints of approved quality conforming to IS : 893118.53.1 15 mm nominal bore

17.31 Providing and fixing 600X450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

8.1 Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately 8.1.1 Raj Nagar Plain White Marble/Udaipur Green Marble/Zebra Black Marble. 8.1.1.1 Area of slab upto 0.50 sqm

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.1 75 mm diameter ( Lenth - 100 )

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.2 110 mm diameter

ITEM ELECTRICAL FITTINGS Wiring point for light with 1.50 sq. mm PVC insulated single core cable in HD PVC condute pipe on surface complete with 1.50 sq. mm PVC insulated Aluminium conductor cable as earth continuity wire drawn inside the conduit complete in all respect. (M.R) Light Rate

Tube Light / Led Light ( Lenth - 1 )

Fan with Box. Rate / Exest Fan ( Lenth - 1 )

Plug Point Box Rate ( Lenth - 1 )

MCB Box Rate ( Lenth - 1 )

RADHEY SHAYAM SHARMA

C S RAWAT