Providing and Erecting to LED Street Light Fitting of Main Gate to Right Side Control Cabin at Juj Dam .

Name of work:- Providing and Fixing to LED Street Fittings of Main Gate to Right Side Control Cabine at Juj Dam

Qty Description Item Rate Per Amount

Supplying and erecting Flexible PVC insulated multi strand

Rupees FourtySix Paise

1 588.00 multi core 1.1 kv grade ISI marked copper wires of following 46.46 Mtr.

size to be erected as directed. FourtySix Only

(e) 1.50 Sq.mm 3 core round PVC sheathed

Supplying and erecting LED street light / Flood light fittings with

High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage Rupees Five Thousand

84 protection. 5976.17 Nine Hundred SeventySix Ea.

Paise Seventeen Only

(ii) above 48 to 60 Watts Cat-lll

providing and erecting Miniature circuit breaker single pole 6A

to 25A suitable to operate on 240 V A.C. system and having Rupees One Hundred

3 84 breaking capacity 10 KA to be erected in existing box. 112.11 Ea.

Twelve Paise Eleven Only

confirming to IS 8828/1996 with ISI Mark (B) cat-(III)

Providing & erecting 415 V MCB Four Pole for Motor &

Rupees Seven Hundred

Inductive Load (C Curve) having 10KA breaking capacity &

4 1 737.30 ThirtySeven Paise Thirty Ea.

confirms to IS :8828 in existing box having following capacity

(c)63 Amp. cat- iii

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be laid Rupees One Hundred

5 910.00 on wall with necessary clamps or in existing trench / pipe of 153.52 FiftyThree Paise FiftyTwo Mtr

following size of cables Only

(A) 4 core 16 Sq. mm

Making trench in soft soil of suitable width of 90 cm deep for

Rupees FiftyFive Paise

6 476.00 laying cable or locating the fault all over the run and back filling 55.55 Mtr

the same and making the surface as normal ground. FiftyFive Only

Making trench in Hard Murrum / Tar Road of suitable width of

90 cm or required depth for laying any size of cable or locating Rupees SeventyFour

7 337.00 the fault all over the run and back filling the same and making 74.74

Paise SeventyFour Only

the surface as normal ground.

Providing & laying approved make Double walled corrugated

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

Rupees SixtyTwo Paise

8 850.00 necessary connecting accessories of same material at 62.62 Mtr

required depth in existing trench for laying of cable. below SixtyTwo Only

ground / road surface for enclosing cable

(A)50 mm outer dia

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Fifteen Paise

9 336 pressure tool & connected to switchgear terminals with 15.15 Ea.

brass/cadmium plated nut bolts in an approved manner.

Replacing Old and u/s by Supplying and erecting approved

make Octagonal pole made from HR sheet steel. The pole

should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local

wind speed with integral Junction box consist of terminal plate

10 of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for

cable termination to be erected With Suitable foundation

(Included) as per details given by manufacturer considering site

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M20 Rupees Eight Thousand

42 Bolts and 600mm long with necessary G.I. J Bolts .Approx 8192.11 One Hundred NinetyTwo Nos.

Pole weight 59 kg Paise Eleven Only

Replacing Old and u/s by Supplying and erecting Street light

pole bracket comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve tubing

of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and bolts Rupees Six Hundred

11 42 for fixing the brackets and having spread of 0.5 mtr. Length 622.16 TwentyTwo Paise Sixteen Nos.

with 110 deg.with vertical plane and suitable welded stiffener Only

reducer and nipple with check nut complete painted with one

coat.of Red oxide / PU base primer and two coats of Aluminium

/ PU paint. paint with following nos of arms.

[B] Double Arm Bracket 0.5 Mtr

Replacing Old and u/s by Supplying & erecting approved make

IP 55 grade Company fabricated Timer Panel of following

capacity for switch On-Off street lights on time scheduling

basis made from 16G CRCA sheet duly epoxy power painted

inside and outside with hinged doors and locking arrangement Rupees Seventeen

12 1 consisting of suitable size of 4 Pole MCB and 4 pole contactor 17059.91 Thousand FiftyNine Paise Ea.

(cat-III)with analog time switch, auto manual switch of same NinetyOne Only

make and suitable input and output Bakelite terminals and

with door earthing approved by Engineer in charge.

(C) 63 Amp Add 1% L.C

Supplying & erecting earth pit of minimum bore dia.150mm

size approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm having 80-

200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following

type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate Rupees Four Thousand

13 4 including value of earth resistance of installation duly stamped 4591.46 Five Hundred NinetyOne Ea.

and signed by agency and officer Incharge has to ensure the Paise FourtySix Only

value of earthing resistane mentioned in test Certificate) &

having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC

62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting HOT deep Galvanised iron strip wire

to 16 SWG. Rupees SeventySeven

Paise SeventySeven Only

I/We am/are willing to carry out the work at ……………………………………………% above/below percent (shouldbe written in figured and

words) of the estimated rates mentioned above. Amount of my/our tender works out as under.

Estimated amount Estimated amount

Put to tender Rs______________ Put to tender Rs______________

Deduct : ___________ % Above RS__________ Deduct : ___________ % Below RS__________

*(Please strike out whitchever is not applicable).

Note 1 – All work shall be carried out as per public works department handbook and other specification of Division ot as directed.

Note 2 – All the columns is schedule should be filled in ink and the total of the entries in the last column should be struck by the

contractor under his signature.

Note 3 – Rates quoted include clearance of site (prior commencement of work and at its close ) in all respects and hold good for

work under all conditions, site, moisture,weather etc.

Note 4 – To be continued on additional sheets, if found necessary.

Note 5 - The rates quoted by the Contractor must be inclusive of all taxes prevailing on due date of bid submission except GST.

However, any subsequent changes in the tax structure by Government after due date of bid submission will be compensated (+/-) on

availability or submission of actual documentation. Contractor will have to intimate Engineer regarding changes occurred in the tax

structure after bid submission. If the contractor fails to provide such information and if any financial obligation may arise due to

change in tax structure, same will be recovered from the contractor. GST will be paid separately on the bills. Hence, it is the

responsibility of the contractor to pay the GST to the concerned Authority.

Deputy Executive Engineer Executive Engineer

Electrical Sub Division Ukai Division No