8961 REPAIR, MAINT AND IMPROVEMENT OF PUMP HOUSES, WATER TANK DISTRIBUTION LINE, PUMPING SET AND ALLIED WORKS UNDER GE (EAST) BAREILLY

Amount

Painting to pipe of pump house rising mains hydrants, sluice valves, pipe, fittings, NRV, discharge head etc after cleaning, srapping and making the surfaces free from rust of main externally and painting with two coats synthetic enamelled paint in black/ blue/ red including marking/ writing on pipe complete as specified and directed

S&F in repair colored chart of water supply diagram of the station in flex sheet of size 2 mtr x 1.5 mtr on 2.5 x 2.5 cm square pipe frame including covered with plastic laminated sheet complete all as specified and directed.

S&F in repair machinary maintenance chart coloured of size approximately 3 ft x 2 ft & 6 mm thick plywood with teak wood frame including covered with plastic laminated sheet complete all as specified and directed.

M&L for trimming vegetation or small inequalities clearing all grass vegetation, saplings, shrubs, brushwood, roots, and tree of surroundings area up to 500 sq mtr including cleaning and removing rubbish upto a distance of 50 mtr outside the periphery of the area under clearance of water supply installations 21 Nos and STPs 04 Nos complete all as specified and as directed.Note-trimming will be done two times during contrct at all installations of water supply.

Supply install in repair and commissioning of Granular chlorination dosing pump of high pressure single head gear motored adjustable dosing pump having output of 2 U.S. GPD to 40 U S GPD and adjustable high pressure of up to 100 PSI (7 kg/cm2)or more ,power input 230 V,50 HZ self priming with nonmetalic with connecting nuts ,ferrules and with all accessories including lead,tubing connection injection check valve complete all as specified and directed.

S&F in repair electric motor 1 HP, 3 phase suitable for mixing of Granular chloronome plant complete all as specified and directed

S&F in repair for Aviation light on OH tank 18/21 mtrs staging (on top of OH tank) with all fittings,fixtures,and accessories including 2.5 sqmm wire T/C in 20 mm PVC conduit from light to connection points ,including 2-way MCB DB with isolator (10 Amp )capacity complete all as specified and directed.

M&L for installation of electronic Automatic level controller including probe unit ,five stage magnetic sensor concealed in S S tube of required length,controlling box including systems incorporated with stage signal,high & low alarm,pump automation as directed (Model ALC Mark-I) capable to one tank from one pump complete all as specified and directed.

M&L for laying in ground Wire from probe unit to controller of 10 pair PVC copper conductor (0.5 sqmm)all as specified and directed(Note:-this item shall be measured in accordance with the quantity required for item no. 05, besides shall also be measured as required in existing level indicators)

S&F in repair for glow sign board (box type) LED of required size 3000 x 600 mm made out of MS sheet of suitable size with sheet fixed on front and quality marked with details of Pump House etc on front and rear with different colours including provision of LED power- fittings & fixtures in equal distance to illuminate board including connections with 2.5 sqmm single core stranded copper conductor cable and writing with 10 mm size and MES logo letters as specified and directed.

Supply & fix repair 1100 volts grade heavy duty cable PVC insulated aluminum conductor screenedserved with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm GI suspension wire, one twin core cables flat or circular of size 10 Sqmm complete all as specified and directed.

S&F in repair Off load change over switch 200 Amp 4pole 415 Volt, complete all as specified and directed. Make- C&S /L&T and Equavalent Approved

Supply and fix in repair energy saving and environemntal friendly long life versatile pressure die-cast aluminium IP-65 roadway luminaire 72 W LED fitting with high power LEDs light source and electronic driver . Make C&S/Crompton/Surya

S& F in replacement new generation post top energy saving environment friendly, long aesthetically designed with symmetrical light distribution spun aluminium landscap luminaire with power LED,s of 35 Watt as light source of 35 Watt suitable for pole dia 76 mm of complete all as specified and directed

S & F in replacement of street light brackets 40 mm dia GI pipe medicum grade upto 1.5 mtr long bend to shape including flat iron clamps and sutable nuts and bolts

Material and labour for replacement of PVC insulated single core multistranded copper cable of size 1.5 sq mm unsheathed 1100 volts grade drawn through conduit / cassing capping on surface / pole /wall concealed and making good of disturbed surface including taking down unserviceable wire all as specified .

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc ( note -(1) credit for above items should be made as per conditions separately.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall.

Taking down light fittings any type, tube light/wall bracket fitting/bldg security light fitting and fixtures, etc, and making good to the disturbed surfaces of walls/floor etc to macth with existing surfaces including white washing/colour washing /distempering to match with existing wall/floor/ceiling finishes.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces.

Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable FRLS of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC casing capping not less then 20 mm width with MS sheet metal sunken switch/Terminal box 1.2 mm thick and phenolic laminated sheet cover 3.0 mm thick and brass screws with cup washers including all necessary wall cutting and making good disturbed surface all as directed and specified. Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate. for following point wirng :-

(a) One light point controlled by one, one way switch

(b) One ceiling /exhaust fan point controlled by one switch, Note : - Rate shall be included for connection of ceiling rose to fan by using 3 core flexible copper wire in white colour complete all as directed and specified

(c) One 3 pin 5 amp socket out point on the same board with other switches.

(d) One3 pin 5 amps socket out let point on independent board

All as per Srl item No. 21 here in before but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 1.5 Sq.mm. earth wire.

Material and labour for switch piano flush type 5A, SP one way. (Make-Anchor,Cona Havell's).

Supply and fixing switch socket combination, 5 and 15 Amps, 230 volt, multi pin, flush type universal all as specified .(Make-Anchor,Cona Havell's).

Supply and fixing switch socket combination, 5 Amps, 230 volt, multi pin, flush type universal all as specified .(Make-Anchor,Cona Havell's).

Lamp Holder(ISI Marked) PVC/Polycarbonate type with back plate suitable for batten fittings, Make : Anchor or equivalent

S&F Ceiling rose, surface bakelite 65x50 mm three terminal Make Anchor or equivalent in GM /Plaza .

Sub main wiring power/circuit using FRLS PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 2.5 Sqmm, earth continuity conductor of size 1.5 Sqmm to be drawn through and including PVC conduit 20mm dia concealed in walls/roof/floors all as directed by Engineer in Charge.Notes:- (i)Two wires of 2.5 sqmm and one wire of 1.5 sqmm and one run of PVC conduit shall be measured as one unit.

Supply and fixing LED Tube light fittings 18 Watt MS batten with decorative enf cap, pre-wired for T8 LED tube light, including 18 Watt LED tube aluminium extruction lamp and mounting clamps etc. all as per makeHavells cat part No LHEXBQP5IN1W018 equivalent to CG/Philips/Bajaj complete.

S&F Bldg Security light energy efficient 1X20 Watt LED 6K Endura cityliner leaf (with Toughned glass) die cast aluminium and fixing arrangement of fitting including 1 mtr 35/50mm GI 90 degree bend pipe complete all as specified (Make: Havells cat No; LHETBXU7PA6S025 equivalent to Philips/Bajaj /CG)

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail , 415Volts SPN with 8 way Double door all as per Cat No.607711 of Legrand or equivalent in Havells/C&S/ABB/Hager Note - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

Supply and fixing MCB SPN 240 Volts, breaking capacity 10 KA of rating 6-32 Amps complete all as specified and as directed.

Supply and fixing MCB SP breaking capacity 10 KA of rating 6-32 Amps complete all as specified and as directed.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm buried directly in ground (earth pi n ot less than 2.25 Mtr b elow normal ground level) connected to galvanized earth lead strip of size 25mm x 4 mm by means of bolts, buts, check nuts and washers of galvanized iro n on steel including 40 mm dia light grade GI tubing for protection of earth lead, MS sheet m etal funnel with wire mesh, watering pipe medium grade 20 mm dia, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 1.50 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar including aluminium strip of size 25 mm x 3 mm for extension of earth lead and necessary excavation, earth work, in soil/loose soil and disposal of spolis to a distance n ot ec 15 Mtr and necessary connection and testing complete all as shown n electrical plate No. 3 and all as direted and specified.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 for concealed water tubing and making good, cutting not exceeding 5 to 10cm girth in RCC/stone walls complete all as directed.

Taking down the Unseviceable LT panel installed at PH and replacement with new one with following parts including panel board Wall mounted LT panel board indoor type of size 1200 x 1200 x400 mm with sheet CRCA sheet of 2 mm thickness comprising of following :- (a) Supply and fix in repair 3 pole power contactor type ML 4 suitable for operation on, 440 Volts, AC, 50 Hz -03 Nos (b) Supply and fix in repair over load protection relay with relay range 45-75A suitable for operation on 3 phase, 415 V -01 Nos (c) Supply and fix in repair voltmeter three phase anologue type class 1 voltage range 0-500 V flush mounting 96x96mm (d) Supply and fix in repair ammeter three phase anologue type 5A class 1 of range 0-200 A flush mounting 96x96mm inculding CT 200/5 (e) Supply and fix in repair MCCB 125 A capacity 3 pole for 415V -01 Nos (f) Supply and fix in repair MCCB 200 A capacity 4 pole for 415V -01Nos (g) Supply and fix in repairs indicating lamp on all 3 phases R Y B -01 set (h) M/L wiring with PVC insulated multistranded copper conductor single core cable 4 sq mm (Nominal cross sectional area) as per site requirement including suitable size of copper lugs etc all as specified and directed-01 Job (j) Supply and fix in repairs single phase preventer direct mounting type with relay range 28-40 A 230 Volts suitable for electric motor of water supply installation-01 No (k) Supply and fix in repairs electronic timer type ST 100 suitable for operation on 240/360/415 volts 50 Hz for 3-10 Sec-01 Nos. (l) Painting complete panel board with one coat of silver inside and outside -01 Job

Supply & replacement of Contactor ML-3 , suitable to operate 35-45 HP submersible pumping set Cat part No SS-90721 Make-L&T

Supply & replacement of Contactor ML-4 ,suitable to operate 50-60 HP submersible pumping set Cat part No SS-90910 Make-L&T

M&L for cleaning of RCC Over Head Tanks capacity 1 lakh gallon removing and taking out sand, sludge and mud etc including disposal of the same at a distance not exceeding 100 mtrs from the tank,including two coats of whitewash on whole internal walls of OH Tank all as directed . NOTE:-All the safety equipments for workers working on OHT and U/G Sumps will be provided by the contactor.Cleaning of OH tank is in every 6 month or contracor is responsible to clean all OH tank two time in their contract at same cost quoted rate.

All as per Srl item No. 39 here in before but capacity 50000 gallon.

All as per Srl item No. 39 here in before but capacity 25000/35000 gallon.

Supply only Aquafit (Calcium based granular disinfectant for water treatment , Packing in 45 KG ,plastic drums complete all as specified and directed .

M&L MCCB, 4 pole, 415 Volt, fixed type 125 to 160 amp with breaking capacity 36 Ka complete all as specified and directed.

M&L MCCB , 4 pole, 415 Volt, fixed type 160 to 200 amp with breaking capacity 35 kA complete all as specified and directed.

Taking out connection of Altoch dosing system , detecting fault and repair /replacement of unserviceable parts ncluding necessary spares such as NRV electric motor for mixing PVC pipe etc as their own cost required for rectifying the defects to be included for smooth functioning the plants and refixing same after completion job and connecting dosing system and testing complete all as specified and directed. Make : Aquafit,Peral filter

Supplying only caustic/Soda crystals/Soda Ash powder in 5 Kg vacuum packets complete all as specified and directed

Supplying only Soda lime powder in 25 Kg vacuum packets complete all as specified and directed

S&F Gate valve (ISI Marked) of following sizes as specified and directed. Make : NMV, ZOLOTO, LEADER

(a) Gate valve of size 50 mm.

(b) Gate valve of size 40 mm.

(c) Gate valve of size 25 mm.

(d) Gate valve of size 20 mm.

(e) Gate valve of size 15 mm.

S&F of 'D' Joint of following dia complete all as specified and directed.

(a) 80 mm dia

(b) 100 mm dia

(c) 150 mm dia

(d) 200 mm dia

M&L for repair/rectification of leakage/blockage to water supply distribution lines of following dia of GI tubing by necessary excavation, returning /filling as required , tightening of lose joints of union ,elbow, socket nipple as per site requirement including for replacement of GI union ,socket, nipple as required complete all as directed.

(a) 15mm dia to 20mm dia

(b) 25 mm dia to 40 mm dia

(c) 50 mm dia

M&L for dewatering complete trenches manually for repairing joints by cocking and inserting spurn yarn and Run lead joint, making good/ leakless the existing joint including necessary excavation and earth work like returning, filling etc for pipes of following dia complete all as directed.

(a) 80 mm dia

(b) 100 mm dia

(c) 150 mm dia

(d) 200 mm dia

M&L for dewatering complete trenches,Repair/rectification of leakage and blockageof PPR pipes manually repairing joints by inserting proper accessories and fittings of PPR pipes making good/ leakless the existing joint including necessary excavation and earth work like returning, filling etc for pipes of following dia complete all as directed.

(a) 110 mm dia

(b) 90 mm dia

(c) 75 mm dia

Supply and fixing CI fittings for CI Bends, connecting pieces, bell mouth pieces, tapers, tee pieces of one end flanged and other end spigot or socket upto 150 mm dia complete all as specified and directed.

S&F of Non Return Valve (ISI Marked) of following sizes at various pump houses complete as specified and directed. Make: KIRLOSKAR, RAMCO or equivalent

(a) NRV of 150 mm dia

(b) NRV of 200 mm dia

Supply only lead for fitting in CI pipe joints complete all as specified and directed

S&F in repairs electronic timer type ST 100 suitable for operation on 415 volts 50 Hz for 3-30 Sec all as specified and as directed. Make : L&T and equivalent.

S&F in repairs electronic timer type ET 100 suitable for operation on 415 volts 50 Hz for 3-10/30 Sec all as specified and as directed. Make : L&T and equivalent.

Supply only grass and weeds killer chemical of make Roundup all as specified and directed.

S&F rubber mat of size 1mtrx2mtrx12 mm at installation of make jyoti or equivalent as directed by Engr-In-Charge

S&F pressure gauge of dial 30 to 60 suitable for fixing at 100/150 header mm pipe with all fiting andf fixtures of make guru or equivalent as specified and directed.

S&F mini motor protection relay for 35-51hp submersibble motores of make L&T all as specified amd directed.

M&L for provision of new wash out points by proper cutting and screwing of existing DI/CI/GI pipe fixing reducer tee of suitable size, supplying and fixing, Jointing, testing CI sluice valve of following size by fixing 02 Nos at each wash out point with flanged ends including necessary mountings nuts, bolts washers and packing fibers gasket on both end and making pit chamber including iron frame cover 3.15 mm thick with locking arrangements complete all as specified and directed.

(a) Wash out point at 150 mm bore pipe

(b) Wash out point at 100 mm bore pipe

Supply and fix in repair spare conntact kit for ML 3 contractor complete all as specified and directed . Make :- L&T/Havells/C&S

Supply and fix in repair spare conntact kit for ML 4 contractor complete all as specified and directed . Make :- L&T/Havells/C&S

S&F in replacement of PVC bib tap 15 mm.

M&L for dismantling of motor, 3 phase, 7.5 KW, taking out burnt winding wire from stator, cleaning all slots properly, repair of pump/rewinding the motor with proper guage of super enamelled winding wire and varnishing properly including baking and providing insulation and packing properly re-assembling the motor with pump and installed at its proper position and testing the same including connection plate.

Lifting/taking out defective submersible pump of any capacity alonwith column pipe of any size and submersible cable, dismantling the pump from motor, setting aside for repair /servicing / overhauling including lowering the pump set into borewell replacemt of packing and nut bolts ( if required) and testing after the completion of repair works in the presence of GE/ Engr in charge .

Rewinding to submersible pump 50 HP of any make with super enameled copper winding wire PVC coated 2 mm thick as per taken out qty , Providing PVC separators , PVC sleeves & jointing compound as specified and directed. Note :- Rewinding, replacement items will be measured and paid seprately under relevent item.If the same motor copper winding wiring burnt second time in the above CA Period, The contractor is responsible to paid and rewind the same at their own cost.

All as per Srl item No. 70 here in before but capacity 41 hp

All as per Srl item No. 70 here in before but capacity 10/15 hp

Repair/Replacement of following parts of the submersible pump and motor for capacity 40/41/50 HP of original company as approved by Accepting officer. Make : KSB, Crompton,Kirlosker

(a) Thrust bearing plate made out of carbon for submersible motor

(b) Gun metal bush for submersible motor

(c) Shaft sleeve made out of stainless steel for submersible motor

(d) Clamp stud for submersible motor

(e) Rotor balancing of submersible motor

(f) Shaft grinding of submersible motor

(g) GM Neck Ring for submersible pump

(h) Stainless steel sleeve for submersible pump

(j) Stainless steel pump shaft for submersible pump

(k) Stainless steel impeller for submersible pump

(l) Cast iron bowl for submersible pump

(m) Rubber bush for submersible pump

S&F in repair sluice valve class PN-1.6 heavy duty flanged ends drilled ISI marked confirming to IS: 14846 suitable for 150 mm bore pipe, wheel operated (Handle) with high tensile stainless steel spindle, including nuts, bolts and jointing with jointing materials etc. complete including taking out old existing unservicable sluice valve including making arrangement for safe working all as specified and directed. Make: BIR, KIRLOSKAR, Kartar

S&F in repair sluice valve class PN-1.6 heavy duty flanged ends drilled ISI marked confirming to IS: 14846 suitable for 100 mm bore pipe, wheel operated (Handle) with high tensile stainless steel spindle, including nuts, bolts and jointing with jointing materials etc. complete including taking out old existing unservicable sluice valve including making arrangement for safe working all as specified and directed. Make: BIR, KIRLOSKAR, Kartar

M&L for RCC overhead reservoir 100000/50000/25000 gallon capacity 50 to 60 feet staging.preparation of old concrete/plastered surfaces by scrapping , brooming etc and applying two coats of exterior emulsion weather proof paint (Apex of Asian paints or equivalent) over dome, wall, columns ,beams including all pipelines etc of overhead reservoir using scaffolding complete all as specified and directed for the following RCC over head reservoir:- Note :- Colour status shall be as under :- (i) Rising main - Blue colour. (ii) Delivery main - Green colour. (iii) Washout main - Red colour. (iv) Overflow main - Yellow colour.

M&L for dismantling of non clog type centrifugal pump set of capacity 12.5HP either fixed or floor or on trolley mounred and taling out unsv spares and performin following operation to complete the task-: Rewinding of the motor centrifugal pumping set with insulated copper winding including sleeves as per originsl approved and replacement of worn out parts including griding of parts testing & transport charges complete all as specified and directed. replacement of motor bearing with lock nut -02 Nos Repalcement of fan motor-01 No Replacement of star coupling set with rubber-01 Each

M&L for dismantling of non clog type centrifugal pump set of capacity 7.5HP either fixed or floor or on trolley mounred and taling out unsv spares and performin following operation to complete the task-: Rewinding of the motor centrifugal pumping set with insulated copper winding including sleeves as per originsl approved and replacement of worn out parts including griding of parts testing & transport charges complete all as specified and directed. replacement of motor bearing with lock nut -02 Nos Repalcement of fan motor-01 No Replacement of star coupling set with rubber-01 Each

Take the water sample from the bore well at ph no. 12, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 20/35, 32, 33, 34, 36, 37, 38, 41, MH PH and two consumer end and send it for physical/Chemical/Bateriological test from any recognised govt agency (two times in contract period) and provide its report to Engr in charge.

Supply fixing testing and commissioning submersible cable flat 16 sqmm 3 core PVC insulated and PVC sheathed with multi stranded copper conductor 1100 volts grade fixed to submersible motor column pipe using suitable size of clamps made out of stainless steel flat of size 20x2 mm with steel nuts bolts & washer foe every column pipe of 3 mtr lenght all as specified and directed.

S&F in replacement MS ERW column pipe screwed 150 mm nominal dia having wall thickness not less than 7.11 mm electric resistance welded with MS flanged 16 mm thick heavy duty confirming to IS 6392 incl 2 mm thick rubber sheet and steel nuts and bolts 10 mm long with washer.

S& F in replacement submersible pump and motor electric driven 415 Volts , TP suitable for 200/250 mm dia bore well casing pipe size 200/250 mm supply complete of 41 HP all as specified and directed.

S& F in replacement submersible pump and motor electric driven 415 Volts , TP suitable for 200/250 mm dia bore well casing pipe size 200/250 mm supply complete of 50 HP all as specified and directed.

VIJAY ENTERPRISES

prabhave traders