Construction of E-2 Category 03 (three) Bunglows at K-Colony, Mithakhali, Ahmedabad.

No figures

1 Excavation for foundation upto 1.5 m depth including 3470.00 Cmt 117.08

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter

lead.(A) Loose or soft soil

2 Excavation for foundation upto 1.5 to 3 m depth 1803.00 Cmt 162.38

including sorting out and stacking of useful materials

and disposing off the excavated stuff upto 50 Meter

lead.(C) Dense or Hard soil

3 Filling in foundation and plinth with sand in layers of 149.00 Cmt 460.19

20 cm. Thickness including watering ramming and

consolidating etc. comp.

soil in layer of 20 cm in thickness including ramming

watering and consolidating etc. complete

5 Applying general insecticide pest control treatment to 1035.00 Smt 89.28

floors, cupboards etc including labour material etc.

complete. Using Imidacloprid 30.5 SC. As Per

Part -II (0.075% concentration by mass) is

recommended 10.5ml chemical diluted with 5 liters of

water application 0.5 liters chemical/ sqm of surface is

recommended as per I.S.

6 Providing and laying controlled cement concrete 1002.00 Cmt 3910.10

M.150 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (A) Foundations and plinth pcc

7 Providing and laying controlled cement concrete 633.00 Cmt 4606.61

M.250 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (A) Foundations, footings and Mass

concrete. footing

8 Providing and laying controlled cement concrete M- 61.00 Cmt 7443.70

250 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in (d) columns Up to Plinth

9 Providing and laying cement concrete 1:2:4 (1- 60.00 Cmt 3697.91

Cement : 2- Coarse sand : 4- graded stone aggregates

20 mm nominal size) and curing complete excluding

cost of formwork in (A) Foundation and Plinth

Item Rate In

Description of Item Quantity Unit Amount

No figures

10 Providing and laying controlled cement concrete M- 140.00 Cmt 7449.56

200 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and

struts For All FLOOR

11 Providing and laying controlled cement concrete M- 194.00 Cmt 5906.48

250 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in Ground & Plinth BEAMS

12 Providing and laying controlled cement concrete M- 136.50 Cmt 5189.38

150 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in plinth Slab

13 Providing and laying controlled cement concrete 181.00 Cmt 6222.86

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) All floor Beams,

14 Providing and laying controlled cement concrete 128.00 Cmt 6642.42

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) All floor Slab

15 Providing and laying controlled cement concrete 13.00 Cmt 6686.86

M.200 and curing complete including the cost of

formwork but excluding reinforcement for reinforced

concrete work in (c) Chhajja for All floor

16 Providing and laying controlled cement concrete 9.00 Cmt 8638.18

M.200 and curing complete including the cost of

formwork but excluding reinforcement for reinforced

concrete work in (c) Lintal for All floor

17 Providing and laying controlled cement concrete M- 14.00 Cmt 7096.92

200 and curing etc. complete including the cost of

form work and excluding the cost of reinforcement etc.

complete in (E) Stair case for All floor

18 Providing and fixing 90 cm high Stainless steel railing 30.00 Rmt 3719.83

made from anticorrocive 316grade S S pipe of 50 mm

dia (16Gauge) as hand rail with S S 316 grade Baluster

of 38 mm dia (16Gauge) as a vertical support fixed in

RCC slab at 1.2m c/c including three horizontal S S

pipes of 25 mm dia (16Gauge) at eqal distance fixed by

18.75 mm dia (16Gauge) S S pipe with baluster

including accessories as per detailed drawing as

directed etc. complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

19 Providing TMT Bar 500D reinforcement for R.C.C. 186552.00 Kg 77.77

work including bending, binding and placing in

position etc complete for All floor

20 Brick work using common burnt clay building bricks 168.00 Cmt 4021.02

having crushing strength not less than 35 kg/sq.cm. in

foundation and plinth in cement mortar 1:6 (1 cement

: 6 fine sand) Conventional

21 Brick work using common burnt clay building bricks 741.00 Cmt 4708.46

having crushing strength not less than 35 Kg/Sq.cm. in

super structure above plinth level upto floor two level

in cement mortar 1:6 (1cement : 6 fine sand)

Conventional {All FLoor}

22 Half brick masonry in common brunt clay building 101.00 Smt 733.16

bricks having crushing strength not less than

35Kg/Sm. In C.M 1:4( 1cement : 4 coarse sand) in

super structure. Conventional for All floor..

23 Providing 20 mm thick double coat mala cement 3711.00 Smt 337.02

plaster on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster

in cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar

1:2 (1 Cement : 2 Coarse sand) finished with trovel

including scaffolding curing, 10x10 mm grooves at

junction of structural member etc. complete. for All

24 Providing 10 mm. Thick smooth cement plaster in 2118.00 Smt 247.31

single coat for plastering on ceiling and soffits of stairs

and finished even and smooth in : (I) Cement mortar

1:4 (1 cement : 4 sand) with floting coat of neat

cement slurry etc. complete. All Floor

25 20mm thick double coat sand faced cement gutka 5907.00 Smt 300.66

plaster on walls upto height 10 metres above ground

level consisting of 12mm thick backing coat of C.M. 1:3

(1-cement : 3-sand) and 8mm thick finishing coat of

C.M. 1:1 (1-cement : 1-sand) including 1cm x 1cm

grooves etc. complete.

26 Providing throating or plaster drip and moulding to 223.00 Rmt 41.66

R.C.C. Chhajja.

27 Applying two coats of (white cement based) or 5615.00 Smt 40.59

(acrylic lappy (putty)) or equivalent and two coats of

primer of approved brand and manufacture on new

wall surface to give an even shade including

thoroughly brushing the surface free from mortar

dropping and other foreign matter and sand papered

smooth. for All floor.

Item Rate In

Description of Item Quantity Unit Amount

No figures

28 Wall painting (two coats) with plastic emulsion paint 3500.00 Smt 144.43

of approved brand and manufacture on undecorated

wall with WITH ONE WALL TO HIGHLIGHT IN

SPECIAL EFFECT (ROYALE PLAY) COLOUR surface to

give an even shade including throughly brushing the

surface free from mortar droppings and other foreign

matter and sand papered smooth.

29 Wall painting (two coats) with plastic emulsion paint 2115.00 Smt 84.64

of approved brand and manufacture on undecorated

ceiling surface to give an even shade including

throughly brushing the surface free from mortar

droppings and other foreign matter and sand papered

30 Finishing wall with TWO COATS OF 100% WEATHER 5903.00 Smt 179.78

PROOF ACRYLIC EMULSION WATER REPELLANT

PAINT and Two coat of primer on wall surface to give

an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of

loose powdered materials.etc complete for All floor

31 Providing And filling with good quality cinder(steam 41.00 Cmt 579.74

coal) as directed by engineer in charge in sunks in

layers of 15 cm thick,including watering,placing

,ramming well etc as directed, for all floor.

32 Providing and laying water proofing treatment by 205.00 Smt 942.33

conventional method including cleaning the slab

surface by wire brush as directed including provding

first layer of C.M. 1:4 of 40 mm thickness mixed with

water proofing compound at rate prescribed by

manufacturer, including putting of brick bats of

average thickness 40 mm Well immerssed in water

laid uniformly on first layer of mortar including

applying cement slurry @ rate of 0.08 bag/sqm. on

fixed layer of brick bats including maintaining

necessary slope, in second layer 40 mm thick C.M 1:4

mixed with water proofing compound as directed,

including finishing smooth with cement slurry as

directed complete.

33 Providing and laying controlled cement concrete M- 52.00 Cmt 5417.29

200 for RCC work and curing complete including the

cost of form work but excluding the cost of reinforced

concrete work in coping on All Floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

34 Providing and fixing openable 25mm thick wooden 82.00 Smt 5730.40

window shutters with a 100mm x 50mm wooden

frame. The outer shutter will feature fixed 5mm thick

tempered or float glass, securely mounted with

wooden beading, and will open outward. The inner

shutter will be fitted with a mosquito net, also secured

with wooden beading, and will open inward. Both

shutters will be crafted from high-quality 25mm thick

wood and finished with melamine polish for enhanced

durability and aesthetics. The window will include all

necessary hardware, such as 3 brass or stainless steel

hinges per shutter, handles, stoppers, and a secure

locking system. Installation will be executed to ensure

proper fit, tight sealing, and optimal functionality,

adhering to the directions of the Engineer-in-Charge

35 Providing and fixing standared extruded of 28.53 Smt 1525.00

alluminium section of size 63.50 x 38.10 x 1.95 mm,@

Wt 1.094Kg / Rmt with colour anodized alluminium

frame with 5 mm thick transparent bronze colour

tinted float glass as details etc complete for Fix

window and Ventilation

36 Providing & Fixing in position standard extruded 11.00 Smt 2823.96

approved colour anodised Aluminum Ventilator with

outer frame 63.50 x 38.10 x 1.95 mm (of Jindal Section

No.4605,@ Wt 1.094 kg/Rmt ) with 3mm thick Bajari

figure adgesteble tinted louvers glass fixed to

alluminium strip blade including fixtures, fastenning,

labours and equipments as per detailed drawing as

directed. For Ventilators

37 Providing and fixing 35 mm thick Flush door DOUBLE 22.30 Smt 4873.25

shutters , solid core finished with Decorative SS Grill

requires teakwood batten around door including

1mm thick lamination on both side, one coat of primer

& two coats of enamel paints on frame & edges and

Melimine Polish, design of which is to be approved by

the architect. Door shall be providing with S.S. Aldrop,

Hinges , stainless steel handle 15cm long , stopper and

necessary Locking system of Godrej, fixtures &

fastenings etc. directed by engineer in charge.

38 Providing and fixing 35 mm thick Flush door Single 110.00 Smt 5197.46

shutters , solid core finished with requires teakwood

batten around door including 1mm thick lamination

on both side, one coat of primer & two coats of enamel

paints on frame & edges and Melimine Polish, design

of which is to be approved by the architect. Door shall

be providing with S.S. Aldrop, Hinges , stainless steel

handle 15cm long , stopper and necessary Locking

system of Godrej, fixtures & fastenings etc. directed by

engineer in charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

39 Providing and fixing 35 mm thick Flush door Double 22.30 Smt 4710.64

shutters, solid core finished with requires teakwood

batten around door including 1mm thick lamination

on both side, one coat of primer & two coats of enamel

paints on frame & edges and Melimine Polish, design

of which is to be approved by the architect. Door shall

be providing with S.S. Aldrop, Hinges , stainless steel

handle 15cm long , stopper and necessary Locking

system of Godrej, fixtures & fastenings etc. directed by

engineer in charge.

40 P & L 60x60 cm' Anti skid glossy vitrified 8 mm thick 576.45 Smt 1361.48

tile for flooring of cement mortar 1:6 (1cement :

coarse sand)and jointed with by adhesive materials

including colour cement slurry including finished with

flush pointing & cleaning the surface etc. complete for

including two colour pattant colour approved by

41 P & L 60x60 cm' Anti skid Glossy vitrified 8 mm thick 121.39 Smt 1556.41

tile for flooring of cement mortar 1:3 (1cement :

coarse sand)and jointed with by adhesive materials

including colour cement slurry including finished with

flush pointing & cleaning the surface etc. complete for

including two colour pattant colour approved by

42 Providing and laying polished Kota stone slab flooring 119.50 Smt 992.66

over 20mm (Average) thick base of cement mortar 1:6

(1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty

:1.5 - coarse sand) laid over and jointed with grey

cement slurry mixed with pigment to match the shade

of slab including rubbing and polishing etc. complete.

(A) 25mm thick

43 Providing and laying polished kota stone slab 25mm 14.00 Smt 1187.79

thick in risers of steps,skirting Dedo and pillars laid on

10mm thick cement mortar 1:3 (1-Cement : 3 coarse

sand) and jointed with gray cement slury mixed with

pigment to match the shade of slab including rubbing

and polishing etc. complete.

44 P & L Mate Finished antiskid ceramic tiles 30 x 30 cm 263.00 Smt 970.07

size 6 mm thick in flooring treads of steps and landing

laid on a bed of 12 mm thick cement mortar 1:3(1-

cement:3-coarse sand)finishing with flush pointing in

white cement

45 P & L premium printed glazed tiles tiles size 30 x 60 602.00 Smt 1441.22

cm 6 mm thick in skirting risers of steps and dedo on

10 mm thick cement plaster 1:3 (1-cement:3coarse

sand) and jointed with colour cement slurry

Item Rate In

Description of Item Quantity Unit Amount

No figures

46 Providing and laying Machine Polished, Machine 39.00 Smt 2505.63

Cutt, Free Edge Granite stone slab 18 mm thick

{Single piece not more than 155 cm long} for tread

and riser of steps, or at any other places incl.

rounded Moulding front edge in trade of steps laid

on 20 mm thick cement mortar 1:6 (1 -cement :

coarse sand) and risers & skiring on 10 mm thick

cement Plaster 1:3 (1 cement : 3 coarse sand)

jointed with grey cement slurry including rubbing

and polishing etc. complete.

47 Providing and fixing pre-cast Rubber Dye / steel Dye 693.76 Smt 686.90

inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming

to IS 15658 : 2006 including 35 mm Sand layer for

levelling and filling the joint with sand in proper line

and level as per guidlines of IRC : SP 63-2018 etc.

48 Providing and laying broken chine mosaic flooring for 1084.00 Smt 747.29

terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or

slope and to be tempered to bring mortar creme out

upto surface using white cement including rounding

off junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as

49 Providing and laying cement concrete 1:2:4 (1- 349.00 Cmt 3738.16

Cement : 2- Coarse sand : 4- graded stone aggregates

20 mm nominal size) and curing complete excluding

cost of formwork as per directed

50 Providing and fixing mirror polished 18 mm thick 347.64 Smt 2439.15

Granite with full round edge and polished of approved

quality in clading on sill and around the doors/

windows/ ventilation with 20 mm thick cement

plaster CM (1:4) and fixing with cement slurry &

adhesive including moulding of exposed edges as

directed by engineering in charge etc. complete.

51 Providing and fixing Safty grills of required pattern for 3366.00 Kg 468.64

windows/ Door using necessary 12mm Dia SS Jindal

304 Rod, SS flats and other structural steel at

required spacing including cutting, welding and

fabriction etc. including Polished of approved quality

and as per detail drawing etc complete.

52 Providing erecting and fixing Triple coated Food grade 21000.00 Litre 10.50

white Syntex or as approved by engineer incharge PVC

(ISI) water tank of required capacity each with all

necessary fittings and connection etc. complete on

Item Rate In

Description of Item Quantity Unit Amount

No figures

53 Providing laying and jointing in true line and level 300.00 Rmt 195.67

50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

54 Providing laying and jointing in true line and level 210.00 Rmt 148.12

40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

55 Providing and fixing concealed center point to wall 270.00 Rmt 249.72

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete. [C] 25 mm.

56 Providing and fixing concealed center point to wall 270.00 Rmt 166.86

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete.[A] 15 mm.

57 Providing, laying and jointing in true line and level 160 42.00 Rmt 831.22

diametre U.P.V.C (Type B) conforming to IS 13592-

1992 with one end plain and other end socketed with

rubber ring, & fittings conforming to ISI 14735-1999

of approved make for drainage system pipe line, pipe

shall be jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of the

size 160 mm diametre x 210 mm length x 196 mm

heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

58 Providing laying (to level or slopes) and jointing 450.00 Rmt 665.48

reinforced concrete Light duty non-pressure pipes I.S.

class NP2 of the following internal diameter with

collars and butt ends prepared for collar joints

including testing of joints complete.(D) 300 mm

59 Providing laying and jointing in true line and level 300.00 Rmt 1127.16

200mm dia. Form core Pipe for drainage including

fittings as approved by Engineer In Charge. Pipe shall

be fixed on existing structure, Wall or ground with

the help of clamp or shall be concelled as directed

including necessary fittings etc. including testing of

pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Item Rate In

Description of Item Quantity Unit Amount

No figures

60 Providing, laying and jointing in true line and level 110 300.00 Rmt 835.15

diametre U.P.V.C (Type B) conforming to IS 13592-

1992 with one end plain and other end socketed with

rubber ring, & fittings conforming to ISI 14735-1999

of approved make for drainage system pipe line, pipe

shall be jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of the

size 110 mm diametre x 149 mm length x 145 mm

heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

61 Providing, laying and jointing in true line and level 75 135.00 Rmt 320.17

mm dia. UPVC SWR Type B pipe conforming to IS

13592-1992 with one end plain and other end

socketed with rubbering and fitting conforming to ISI

14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall using of

PVC clamp at every 2000 mm c/c or shall be conceled

in walss as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement

including cost of all materials.

62 Providing and fixing in PVC SWR cowel went 75mm 9.00 No 15.66

dia to pipes.(B) 75mm dia.

63 Providing and fixing in PVC SWR cowel went 110mm 30.00 No 28.79

dia to pipes.(B) 110mm dia.

64 Providing and fixing PVC SWR Nahni trap IS 14735 for 36.00 No 571.08

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I

scread down or hinged grating including the cost of

cutting and making good the walls.

65 Providing and fixing Wall Hung CERA or equivalent 12.00 No 22460.38

CARLTON Cat.No.S1044147 snow white size

490x350x360mm P Trap with Duroplast slim soft

close seat cover including Health Faucet ABC body

with 1 m SS Braided connection pipe, Flush cock

Consisting of exposed part F1013751 (Lever,

Cartridge, sleeve, flange) and Concealed part

F4060102 with all fitting inlet and outlet connection

and all required fitting accessories etc. completed as

per directed engineer in-charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

66 Providing and fixing orissa pan 580x 440 mm COLVIN 3.00 No 7534.60

S3010108 Snow white color P Trap with connection

pipe, Flush cock Consisting of exposed part F1013751

(Lever, Cartridge, sleeve, flange) with all fitting inlet

and outlet connection and all required fitting

accessories etc. completed as per directed engineer in-

67 Providing and fixing ball cock of approved. quality as 6.00 No 189.84

directed.(A) Copper Metal (ii) 50mm dia.

68 Providing and fixing Wash Basin CERA or equivalent 15.00 No 5908.50

CHERUB Cat. No. S2020112 Snow White size

400x400x135mm including Polyamide braided

connection pipe 12mm dia, 450mm length Cat. No.

F8070402, Wast coupling with ceramic Pop-up push

type (Full thread) 32mm Dia Cat. No. F8050351 with

all fitting inlet and outlet connection and all required

fitting accessories etc. completed as per directed

engineer in-charge.

69 Providing and fixing Swivel Mirror 630 X 445mm 15.00 No 5027.78

Rectangular Shape including all Fittings and labour

charges etc. Completed as per directed engineer in

70 Providing and fixing Single Towel Rail 300mm Long 15.00 No 4292.50

(AQN-GRF-7711B) including all Fittings and labour

charges etc. Completed as per directed engineer in

71 Providing and fixing CERA Bib cock with Wall Flange 24.00 No 2657.31

and aerator Cat.No. F1016151 with 15mm dia

extension nipple including all Fittings and labour

charges etc. Completed as per directed engineer in

72 Providing and fixing CERA Pillar cock with 310mm 15.00 No 4066.26

long extended body and aerator Cat.No. F1016102

including all Fittings and labour charges etc.

Completed as per directed engineer in charge.

73 Providing and fixing in position 300 mm high, 150 mm 90.00 No 707.00

wide English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

74 Providing and fixing WALL MIXER ( 3-IN 1) Cat. 15.00 No 8633.48

No.F1019403 Chrome Plating including all Fittings

and labour charges etc. Completed as per directed

engineer in charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

75 Providing and fixing CERA Angle cock with wall flange 21.00 No 2045.25

Cat.No.F1016201 including all Fittings and labour

charges etc. Completed as per directed engineer in

76 Providing and fixing Overhead Shower 120mm Round 3.00 No 4359.16

Shape Multi Flow with Cascade Effect (ABS Body

Chrome Plated with Gray Face Plate) with Rubit

Cleaning System including all Fittings and labour

charges etc. Completed as per directed engineer in

77 Providing and fixing S.W. gully trap with C.I. grating 15.00 No 1246.92

brick masonry chamber and water tight C.I. cover with

frame of 300mm x 300mm size (inside) with standard

weight (i) Square mouth traps (B) 150mm x 100mm

size P or R type

78 Constructing brick masonry chamber for underground 53.00 No 3172.41

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 455mm x 610mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix

(1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete (i) Inside dimensions 455mmx

610mm and 450mm deep for single pipe line.

79 Constructing brick masonry chamber for underground 53.00 No 3883.45

C.I. Inspection C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg.

Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm

intenal dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on

walls and bed concrete etc. complete (i) Inside

dimensions 500mmx 700mm and 450mm deep for

single pipe line.

80 Extra over items for every additional depth of 0.1M. of 45.00 Each 242.39

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 455mm x 610mm size.

81 Extra over items for every additional depth of 0.1M. of 45.00 Each 264.86

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 500mm x 700mm size.

82 Providing cement vata (10cm x 10cm size) quarter 131.00 Rmt 23.68

round in cement mortar 1:1 including neat cement

finishing watering etc. Complete

Item Rate In

Description of Item Quantity Unit Amount

No figures

83 Providing and fixing MS Ladder of required pattern 900.00 Kg 110.09

with MS flats(30x3mm) or round or square bars

(12mm) at required spacing & with round headed

bolts and nuts or screws or welding including primer

coat of approved quality and two coats of oil paintas as

directed by engineer in charge

84 Providing and fixing in position 150 mm high, English 60.00 No 404.00

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools

& plants etc. complete.

85 Providing and fixing Kitchen SS Sink Glosy ASIS 316 9.00 No 2057.37

Grade x 1mm thick with over all size 610x460 mm &

bowl size 560x410x200 including cutting holes in

walls and making good the same including necessary

fittings with 32mm dia C.P brass waste , 32mm dia M.I

fisher union and Rubber plug Etc. completed

86 Constructing Sandwitch Platform of 15mm-18 mm 19.00 Smt 5373.33

thick Polished Black Granite at top and 25 mm thick

Kota stone slab one side polished at bottom with

cementing Materials / adhsives including makeing

necessary grooves in walls with Vertical sandwich

two Kotastone 25 mm support every 60 cm centre to

centre covered with granite patti or as required

including all labour material of approved quality incl.

full moulded round front edge granite strip of one side

polished and jointed with grey cement slurry

including rubbing and polishing etc. complete for all

87 Providing and fixing kitchen platform trolley having 23.00 Smt 12664.39

three drawers of SS (IS 304) of required size like thali,

katleri, perforated, partition, cupsosar type in kitchen

platform having drawer front side and backside by

using 19mm thick all proof plywood of ISI quality all

side laminated etc. as directed. The size of SS (IS 304)

basket of size 4" to 18" for thali, dish, katleri,

perforated, partition, cupsosar type as directed

including necessary S.S. fittings, handles, nobs,

telescopic channels, etc. as directed

88 Steel work, welded in built up sections framed work 4763.00 Kg 84.13

including cutting, hoisting, fixing in position and

applying a priming coat of read lead paint & two coat

oil paint. (A)In beams and joists, channels angles Tees,

flats, with connecting plates or angle cleats as in main

and cross beams. Hip and jack rafters, purlins

conneted to common rafters and the like..

Item Rate In

Description of Item Quantity Unit Amount

No figures

89 Providing Plinth Protection to Building including 503.00 Smt 2252.81

excavation in ordinary soil and laying cement concrete

1:3:6 using stone aggregates of 40mm nominal size in

foundation layer 125 mm thick+ 125mm thick sand

layer below pre-cast Rubber Dye inter locking

concrete block 60mm thick with grade of concrete

M300 pneumatic compressed by mechanically pressed

and as per approved design including 75mm Sand

layer for levelling and filling the joint with sand in

proper line and level etc. complete, Including

Providing and fixing pre-cast concrete kerb stone of

grey cement based concrete block 30cm length, 30cm

height and 15cm thick made of M250 grade concrete

as per approved design and including excavation for

fixing in proper line and level, filling the joint with C:M

1:3 (1cement:3 fine sand) etc. complete.

90 Box cutting the road surface to proper slope and 948.00 Cmt 102.92

camber for making a base for road work including

removing the excavated stuff and depositing on the

road side slope as directed upto 50Mt.lead.

91 Construction of granular sub-base 150 mm thick by 237.00 Cmt 1607.92

providing coarse graded machine crushed B.T.

material satisfying MOST specification of grading I

(B.T. stone aggregate 53 mm to 26.5 mm 35 %, 26.5 to

4.75 mm - 45 % and 2.36 mm below - 20 % )including

spreading in uniform layer with motor grader on

prepared surface, mixing by mix in place method with

rotavator at OMC and compacting with vibratory roller

to achieve the desired density etc. complete.

92 Providing and laying wet mix macadam base course 237.00 Cmt 1720.03

150 mm thick using machine crushed B.T. chips as per

required gradation mixing with required optimum

quantity of water, conveying the mix to site of work,

spreading in to grade and camber with mechanical

paver and consolidation each layer with vibratory

roller including cost of material labour plant and

equipment etc. complete.

93 Compaction and finishing of cement concrete road by 1322.00 Smt 63.63

trimix M.250 process providing extra Labour charges

for the trimix vaCmte dewatering service process on

cement concrete road sutface by using vacuum

dewatering pump floater surface vibrator including

making groves and rough finish to surface including

leveling etc complete.

94 Providing and Laying homoginious Grey cement based 345.00 Rmt 361.64

concrete kerbing of size 30 cm x 30 cm x 10 cm size as

per detailed drawing having grade of concrete M25

grade, including necessary excavation, BBCC 1:5:10

cm as per ddetailed drawing fixing in line and level,

filling joints in CM 1:3 with smooth finished, white

washing three coats etc. complete as directed by

Engineer in charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

95 Demolition of Brick work and stone masonry including 132.00 Cmt 550.40

stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift.(ii) In

Cement Mortar

96 Providing and fixing decorative entrance gate made 2400.00 kg 155.54

out of cast iron and various mild steel tabular section

combination , the Ornamental entrance gate should be

fixed at compound wall including pattern and die

making , cutting , welding , grinding, fabrication , fixing

in position at compound wall with necessary pedestal,

bearing block and other locking arrangement. The

entrance gate should be painted with two coats of

priming coat of paint, and two coat of oil paint etc

complete. As per detail design and instruction of

architect.

97 Providing and fixing concertina coil fencing with 559.00 Rmt 460.56

punched tape concertina coil 600 mm dia 10 mt

openable length having 50 no rounds per 6 mt length,

upto 3mt height of wall with existing angle iron

(50mm x50mm x5mm )requird shaped As per

Directed Engeenier in charge. placed 2.4mt or 3.00mt

apart and with 4 horizontal R.B.T. reinforced barbed

wire(3 mm) , stud tied with G.I. staples and G.I. clips to

retain horizontal, including necessary bolts or

G.I.barbed wire tied to angle iron, all complete as per

direction of Engineer-in-charge, with reinforced

barbed tape (R.B.T.)/Spring core (2.5 mm thick) and

weight 43.478 gm/meter at compound wall for ESR

M4/ intakewell.

98 Providing and fixing of Ridge flashing for roof panel 90.00 Smt 858.67

shall be made out of 0.5 mm thick pre coated GI sheet .

The Precoated sheet shall be of minimum 240 mpa

steel grade confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm as per

IS:277:1992 , 5-7 microns epoxy primer on both side

of the sheet and polyester top coat 15-18 micron. The

PPGI Sheet shall have plastic protective guard film of

minimum 25 microns to avoid scratches during

transportation. The ridge shall be fixed to the steel

members by pop rivet or self drilling/self stitching

fastners @ maximum 450 mm c/c along length of

capping/flashing etc complete .

99 Providing and fixing to wall ceiling and floor 10.0 Kg. 170.00 Rmt 336.24

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and

floor.(G)110 mm

100 Providing and fixing to wall ceiling and floor 10.0 Kg. 180.00 Rmt 696.90

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and

floor.(G)160 mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

101 Providing junction for rain water juncton chamber of 30.00 No 8758.72

size 0.60x0.60x0.75m with excavation of size

1.96x1.96 m & 0.15m thick c.c.1:2:4 bed concrete

including brick masonary wall in CM 1:6 of 0.75m

height & 0.23m thick with 15mm thick cement plaster

inside & outside & 1.06x1.06 RCC (1:2:4) slab of

thickness 0.15m with CRS steel and 0.60mx0.45m cast

iron manhole cover with frame weight not less than

kg as per directed by Engineer-in-charge

102 Providing Filter chamber of Brick work in C:M 1:6 of 2.00 No 15303.52

size 2.06mx1.20m x1.20m & excavation dimension of

2.66mx 1.81x1.35m including C.C 1:2:4 bed concrete of

0.15m thick including brick work in c.m 1:6 for 23cm

thick wall including 15mm thick cement plaster inside

& outside with cement slurry & 10cm thick RCC 1:2:4

top cover with frame of minimum weight of 35 kg &

filling filter material kapchi in layers (25-40mm & 10-

20mm) & BT metal 40mm & sand as per directed by

Engineer-in-charge

103 Providing Recharging pit of size 2.0m Dia.& 2.0m 2.00 No 11442.29

depth of water logging with excavation filling the pit

with gravel & sand in layers including making 300mm

dia bore depth of 4.5mt & above concrete with kapchi

in layers (25-40mm & 10-20mm) & BT metal 40mm &

filling brick as directed by Engineer-in-charge.

104 Drilling of min. 250 mm dia. bore hole in all strata 300.00 Rmt 1270.58

including dualover burden strata by combination

DR/DTH rig including lowering 200 mm dia MS ERW

pipes in bore hole and testing etc.all work as per

directed engineer incharge.

105 Supplying slotted PVC pipes of approved quality at site 300.00 Rmt 555.50

of work confirming to IS. 1239/1974 180mm dia.

106 Cleaning & maintenance of system Including all 1.00 No 4646.00

Labour and replacing of Filter Media as Required for

107 Excavation for foundation for depth from 3.0 m to 18.00 Cmt 174.23

5.0 m including sorting out and stacking of useful

materials and disposing off the excavated stuff

upto 50 Meter lead.(B) Dense or Hard soil

108 Providing and laying controlled cement concrete M- 26.00 Cmt 8194.13

250 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in (B) Walls, from top of

foundation level upto floor two level

Item Rate In

Description of Item Quantity Unit Amount

No figures

109 Providing and fixing C.I. Manhole cover 0.60 M. x 2.00 No 958.17

0.45M. size having weight not less than 35Kg.

110 Providing and fixing rolling shutters of approved make 10.00 Smt 3503.41

made of 80 mm wide M.S laths inter-locked together

through heir entire length and jointed together at the

ends by end locks mounted on specially designed pipe

shaft with bracket plates,guide channels and

arrangement for inside and outside locking with push-

pull operation including the cost of hood cover and

sprig etc.complete(A) Shutters having width below

111 Drilling of Pilot bore hole in all strata by mud flush 300.00 Rmt 600.95

DR Rig 250/300 mm dia.

112 Reaming of 250 mm /300mm dia pilot bore 300.00 Rmt 184.83

Hole including assembling lowering housing casing

strainer pipes with gravel packing clay balls packing

etc without cost of cement 550 mm dia.

113 Cement sealing if necessary without cost of cement 1.00 Job 15014.66

by means of Mud Pump.

114 Lowering and removing of 100mm dia. dropline 1.00 Job 27720.46

and 32mm dia. airline for development of each

water bearing zones comes across upto the full depth

of deep tube well of size 200mm / 250mm / 300mm

dia. for the tubewell having depth 186 Mtr. and

above through suitable air compressure. The job is for

complete period of development of tubewell.

(without air compressor charges) (Min 8 Hrs. & upto

Sand free discharge)

115 Charges of air compressor of 900 CFM /200 psi 24.00 Hour 8499.15

capacity for minimum 6 running hours.

116 Manufacture, supply and delivery of ISI marked 230.00 Rmt 3605.70

ERW M.S. pipes conforming to IS: 4270/2001 with

latest amendment in rendom length of 4 to

meter size 250mm diameter (minimum 7.10mm

thickness)

Item Rate In

Description of Item Quantity Unit Amount

No figures

117 Manufacture, supply and delivery of cage 60.00 Rmt 3088.58

type Trapezoidal shape ('V') wire wound low

carbon, Galvanized screen pipe and stainless steel

screen pipe confirming IS: 8110 GWSSB R/C (E)

250 mm dia (1) Having Size of 1.0 mm slot (Heavy

118 Manufacture, supply and delivery of cage 15.00 Rmt 2001.82

type Trapezoidal shape ('V') wire wound low

carbon, Galvanized screen pipe confirming IS:

GWSSB R/C (D) 200 mm dia (1) Having Size of

mm slot (Heavy Grade).

119 Clamps made from M.S. Plate with Hole on either side 2.00 Pair 2037.91

with nuts & bolts of Std. Make size 900mm x 100mm x

16 mm flat suitable for 250mm dia. pipe.

120 Bore Plug having 100 mm height made from M.S. Plate 1.00 No 1161.62

with 3 Holes at equal distance on circumference for

nut bolts type locking arrangements with nut bolts

& lock nuts of Std. Make complete from 5mm thick

M.S. plates (for top also) suitable 250mm dia. pipe.

121 Supply of misc bore materials like steel bend 300.00 No 91.71

plate suitable for ERW pipe of dia 250 mm of size

122 Supply of ISI marked portland cement of store or site 1.50 Ton 5286.34

of works including all tax with loading, unloading,

freight etc. complete as directed.

123 Supply of well sorted "Sevalliya" gravels of size 40 30.00 Cmt 2049.29

mm to 63 mm including carting loading,

unloading & stacking at site of work.

124 Supply of clay ball having size of 25mm to 50mm from 30.00 Cmt 758.51

Sicky Clay at site of work.

125 Charges of electrologging test of bore hole.Uptron 1.00 Job 18180.00

make electrologger with carting.

126 Geohydrological ground water investigation 1.00 Job 14428.86

(with vehicle charges) deep tube well (with water

sample testing) for 200mm/250mm diameter deep

tube well (with water sample chemical Analysis).

Item Rate In

Description of Item Quantity Unit Amount

No figures

127 Heavy Duty clamps made from 4" x 1.5" iron strin 2.00 No 333.30

suitable for column pipe 1.5" to 2" length. (E)

100mm (4") dia. Pipe.

128 Supplying and erecting ISI marked sluice valve 1.00 No 4575.30

at position with necessary materials for following

size of pipe diameter (vi) 100mm dia.

129 Supplying and erecting CI Swing check type non- 1.00 No 3383.50

return (Reflux) valve ISI marked suitable for 100mm

130 Supplying & Erecting Mild Steel heavy duty 8.00 No 248.46

Flanges with rubber packing and hardware

materials for pipe connections suitable for (D)

131 Supplying & erecting G.I. Bend for pipe connection 3.00 No 646.40

suitable for (g) 100 mm (4")

132 Providing and fixing conceled center point to wall 200.00 Rmt 1486.52

ceiling and floor CPVC( SDR 13.5) pipe having

National Senitation Foundation (NSF) seal for

potable water of following nominal dia, tube

fittings and Z clamps including making good the

wall ceiling and floor etc. complete. 100 mm dia.

133 Providing and fixing concealed center point to wall 200.00 Rmt 653.77

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete. [F] 50mm.

134 Excavation in any soil upto 30 cm. depth, bracking 929.00 Cmt 261.10

clods, removing unwanted stuff such as brick bats,

stones, grass roots etc. refilling the same, preplanting

watering, weeding, top-digging relevelling and

bringing the earth to fine tilth, ready for sowing or

135 Providing Loam or clay soil of approved quality on 929.00 Cmt 484.80

136 Providing labour for spreading & Mixing Loam or clay 929.00 Cmt 203.83

soil or river silt evenly over the excavated area and

levelling the same after breaking clods et.(Rate for one

Cum of soil)

Item Rate In

Description of Item Quantity Unit Amount

No figures

137 Providing Farm Yard Manure of approved quality on 155.00 Cmt 1034.24

138 Providing labour for spreading & mixing the manure 155.00 Cmt 203.83

evenly with 8 to 10cm on prepared area @ 5Cum/100

smt. Area.(for 1 Cum of manure) Rate

139 Providing pure Carpet Lawn in blocks and planting the 3095.00 Smt 461.79

same at a distance of 8 to 10 cm. both way and

maintain the same till is well established (about

140 SHRUBBERY PLANTATION:Supply well grown shrub 317.00 Smt 1133.07

plants and ground cover plants of average height 3' to

4' and planting in 2 rows at 300 mm c/c in 300 x 300 x

300 mm size pits by providing and mixing FYM @

Cum/pit with soil pesticide & Insecticide. Plants

should be disease free and fungus free in 8'' x 10''

polythene bag. Plastic bags or pots should be removed

carefully and soil around the roots should not be

dropped or disturbed much. Bill shall be placed after

completion of maintenance period but not before

stabilizing the shrubs. Mortality rates to be inclusive.

Work shall be done as shown in the drawing or as

directed and approved by EIC. The ground coverage

should be dense and uniform throughout the planting

141 TREES PLANTATION: Supplying and planting of trees 176.00 No 759.89

of specified variety including excavation of pit 600 x

600 x 600 mm depth mixing of FYM & existing soil in

ratio 1:3, trmite treatment, and planting of plants

(height 8' 10' above bags/pots). Soil mounts 4'-8'' in

size. Tree plantation should be carried on neatly

accurately and with perfection as per drawing and

instruction given by the EIC. Plastic bags or pots

should be removed carefully and soil around the roots

should not be dropped or disturbed much. Bill shall be

placed after completion of maintenance period but not

before stablizing the hedges. Rates for mortailty to be

inclusive. Providing and fixing tripod made of wooden

ball, height 1.50 mtr. Top bracket to be 300 mm x

mm leg embedded in ground up to 300 mm and to

have tar coat. Work shall be done as shown in the

drawing or as directed and approved by EIC.

Item Rate In

Description of Item Quantity Unit Amount

No figures

142 Constructing brick masonry chamber for underground 10.00 No. 7180.44

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions, total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(iii) Inside dimensions 600mm

x 850 mm and 450mm deep for pipe lines with three

or more inlets.

Total (A)

143 Point wiring for Light / Bell with 2-1.5 sq.mm & 171.00 Ea. 485.81

earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length , in below type of

pipe erected with 6A Modular type switch / bell push

& accessories and earth continuity of following type,

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector

as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

144 Point wiring for Light / Bell with 2-1.5 sq.mm & 60.00 Ea. 242.91

earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length , in below type of

pipe erected with 6A Modular type switch / bell push

& accessories and earth continuity of following type,

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector

as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete (for bath & w.c. 50% of point wiring

taken)Cat. III

Item Rate In

Description of Item Quantity Unit Amount

No figures

145 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 51.00 Ea. 674.68

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and

accessories with earth continuity of following type

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete, Cat. III

146 Providing following type of Modular Type Accessories 243.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (1)One No. SP 6 Amp., Cat.III

147 Providing following type of Modular Type Accessories 192.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (2) One No 5 pin plug, Cat.III

148 Providing following type of Modular Type Accessories 18.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (3) Two Pin/RJ-11 Telephone

Socket, [A] For One Gang Cat.III

149 Providing following type of Modular Type Accessories 18.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (4) TV Co-axial Socket outlet

150 Providing following type of Modular Type Accessories 24.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (8) Computer RJ-45 socket

Item Rate In

Description of Item Quantity Unit Amount

No figures

151 Providing following type of Modular Type Accessories 60.00 Ea. 180.79

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (9) 16 Amp. SP one way switch,

152 Providing following type of Modular Type Accessories 87.00 Ea. 199.98

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (10) 6/16Amp. Universal socket

153 Providing following type of Modular Type Accessories 27.00 Ea. 310.07

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (13) 6A/10A/16A/20A/25A/32A

Single pole Modular MCB Switch , Cat.III

154 Providing following type of Modular Type Accessories 6.00 Ea. 329.26

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (19) Modular Indicating Call Bell

155 Providing following type of Modular Type Accessories 27.00 Ea. 316.13

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (21) Foot Light as per colour

requirement with concealed box, modular accessories,

acrylic glass cover with suitable LED watt with all

accessories as per following module, (a) Two modules

156 Providing following type of Modular Type Accessories 30.00 Ea. 682.76

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (23) USB Charger with output of

V DC,2.1 A with inbuilt surge protection.

Item Rate In

Description of Item Quantity Unit Amount

No figures

157 Point wiring for Two Way Controlled Light Point with 15.00 Ea. 603.98

2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both

are of .ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires erected in below type of

pipe with 6A Modular type switches and following

type of accessories erected on PVC / Metallic/Wooden

box, single mounting base frame covered with

textured / metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected. with

necessary batten/angle holder or ceiling rose or

H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete, Cat. III

158 Providing and erecting Mains with 1.1 KV grade FRLS 4200.00 mtr 82.82

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed

in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories,

(b) 2 wire 2.5 sq. mm

159 providing and erecting Mains with 1.1 KV grade FRLS 1305.00 mtr 112.11

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on

wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth

continuity of following size (A) with medium class

Rigid PVC pipe and accessories

(a) 2 wire 4 sq. mm

160 providing and erecting Mains with 1.1 KV grade FRLS 180.00 mtr 147.46

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on

wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth

continuity of following size (A) with medium class

Rigid PVC pipe and accessories (b) 2 wire 6 sq. mm

161 providing and erecting Mains with 1.1 KV grade FRLS 180.00 mtr 425.21

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on

wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth

continuity of following size (A) with medium class

Rigid PVC pipe and accessories (i) 4 wire 10 sq. mm

(use earth wire of 4 sq.mm )

Item Rate In

Description of Item Quantity Unit Amount

No figures

162 Providing & Erecting approved make following size of 1080.00 mtr 62.62

TV Co-axial flexible cable comprising inner conductor

of solid bare copper insulated with Foam PE &

Secondary conductor made of poly - Aluminium film

bonded Al. Braids @ suitable coverage overall

sheathed with black PVC insulation. e).RG-11

163 Supplying & erecting approved make LAN cable of 1440.00 mtr 47.47

following size in existing pipe as per direction [C] CAT -

164 Providing and erecting ISI mark Medium class RIGID 2520.00 mtr 24.24

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution

& Clamps with following dia of pipes, in approved

manner as directed (a)20 mm

165 Supplying and laying UPVC cable trunking system 200.00 mtr 428.24

comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming

BS with necessary end caps Internal and external

bend, flat bends, coupler, tee etc..All necessary

accessories and measuring of following sizes (2)

mm x 50 mm trunking

166 Providing and erecting Sheet Steel powder coated 6.00 Ea 1492.78

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

suitable for (A) single phase incoming and horizontal

single phase outgoing (b) sheet steel double door (IP-

43) (iii)(iv)12 way

167 Providing and erecting Sheet Steel powder coated 6.00 Ea. 3412.79

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

suitable forB) three phase incoming and single phase

horizontal type outgoing Per phase isolation type

(PPI) (b) sheet steel double door (IP-43). (iii)8 way

168 providing and erecting Miniature circuit breaker 168.00 Ea. 112.11

single pole 6A to 25A suitable to operate on 240 V A.C.

system and having breaking capacity 10 KA to be

erected in existing box. confirming to IS 8828/1996

with ISI Mark , Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

169 Providing & erecting 240 V MCB double pole switch 9.00 Ea. 299.97

for motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing

box having following capacity , (A) 6 to 32 Amp.

170 Providing & erecting 415V MCB Four Pole Switch for 6.00 Ea. 638.32

Lighting Load (B curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

following capacity, (b)40 Amp. , Cat.III

171 providing and erecting Approved make RCCBs 24.00 Ea. 1969.50

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with

all advance feature & do not incorporate any

electronic component. for following Max. rating

erected as directed (i) 25 Amps.DP . Cat. III

172 Providing and erecting Approved make Four pole 6.00 Ea. 6173.12

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all

internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

173 Providing and erecting Approved make Four pole 6.00 Ea. 6790.43

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all

internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III (With Enclosure)

174 Supplying and erecting LED indoor fittings with LEDs 84.00 Ea. 373.70

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

shown.) (A) Tube Light with integral driver, (iv)

Watts, Surge - 2KV,IP-20, conventional 4 feet, Cat-lll

Item Rate In

Description of Item Quantity Unit Amount

No figures

175 Supplying and erecting LED indoor fittings with LEDs 66.00 Ea. 589.84

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

shown.)(A) Square/ Circular shaped Surface/Recessed

Mount Downlight with provision for spring loaded

mounting clips complete.IP20, (iii) 16-20 watts, Surge-

2 KV, Cat-lll

176 Supplying and erecting LED indoor fittings with LEDs 21.00 Ea. 312.09

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

shown.) (H) Mirror Light 9 Watts, wall mounted

minimum 1 feet long

177 Supplying & erecting approved make street light box 45.00 Ea. 1501.87

comprising CNC Processed robust housing made from

single sheet multi folded with high grade powder

coating ( RAL-7032 Structure finish as Standard) of IP-

55 degree of Protection Gasket(PU Gasketing) of

following size of Box.

178 Providing and erecting XLPE(IS:7098)(I)-88 ISI 1625.00 mtr 364.61

armoured cable multistrand / Solid Copper

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road

crossing or floor of following size of cables. (B) 4 core

Item Rate In

Description of Item Quantity Unit Amount

No figures

179 Providing & laying approved make Double walled 1625.00 mtr 62.62

corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting accessories

of same material at required depth in existing trench

for laying of cable. below ground / road surface for

enclosing cable

(A)50 mm outer dia

180 Making trench in soft soil of suitable width of 90 cm 1625.00 mtr 55.55

deep for laying cable or locating the fault all over the

run and back filling the same and making the surface

as normal ground.

181 Supplying and erecting LED street light / Flood light 60.00 Ea. 3161.30

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.) (b) LED Bollard fittings

of minimum height 600 mm & dia.100mm having

polycarbonate clear/milky diffuser mounted on 3mm

thick aluminium finished powder coated pipe with

base plate 160x160mm with erection by M8x75mm

fastner with required RCC foundation.IP65 for 9 to

watt ,surge-4kv- cat-III

182 Supplying and erecting Flexible PVC insulated multi 200.00 mtr 46.46

strand multi core 1.1 kv grade ISI marked copper

wires of following size to be erected as directed.(e)

1.50 Sq.mm 3 core round PVC sheathed

183 Supplying and erecting Flexible PVC insulated multi 408.00 mtr 77.77

strand multi core 1.1 kv grade ISI marked copper

wires of following size to be erected as directed (h)

2.50 Sq.mm 3 core round PVC sheathed

Item Rate In

Description of Item Quantity Unit Amount

No figures

184 Supply, Installation, Testing and Commissioning of 51.00 Ea. 2885.57

suitable sweep, BEE 5 Star rated, Ceiling fan with

Brush Less Direct Current (BLDC) permanent ferrite

magnet Motor, class of insulation: B, Rust free

nos.Aluminium blades, 2 nos. canopies, shackle kit

with earthing provision, copper winding, Power factor

not < 0.9, Service Value (CMM/W) minimum 6.85, Air

delivery minimum 215 CMM, 350 RPM,230v

(tolerance as per IS : 374-2019), THD < 10%, with

remote unit for Speed Control and all remaining

accessories including safety pin, nut bolts, washers,

temperature rise = 75 degree C (Max.), suitable for

140 to 285 Voltage and rectifier circuit with surge,

over current and overload protection , 50 Hz, Single

phase AC Supply, earthing etc. Complete as required.[

Make shall be approved by Engineer in Charge] (B)

1200 mm Sweep (48")

185 Supplying & erecting approved make low noise 21.00 Ea. 1703.87

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame.

200mm with 1350RPM Cat.II

186 Providing and erecting XLPE (IS:7098)(I)-88 ISI 60.00 mtr 153.52

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables, (A)

core 16 Sq. mm

187 Providing and erecting decorative wall bracket fittings 21.00 Ea. 1712.96

complete with LED lamp and rust free fittings

components mounted in chrome finish housing with

holder ,clear/opaque glass diffuser complete erected

with lead wires with minimum 15 wattage capacity (as

per instruction engineer incharge/architect/authority

(up & down lighter, wall washer, liner lights etc.)

Item Rate In

Description of Item Quantity Unit Amount

No figures

188 Supplying & erecting earth pit of minimum bore 6.00 Ea 4591.46

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm

with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make

OEM has to submit test certificate including value of

earth resistance of installation duly stamped and

signed by agency and officer Incharge has to ensure

the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B)

Inner chemical (CCM Compound)- Resistivity:-

ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time

Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

189 Providing & erecting weather proof, dust & vermin 6.00 Sq.Mtr 14902.55

proof, floor mounted front operated indoor type

cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer body

& doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions &

cable alley as per requirements & instruction of

engineer-in-charge with erection of supplied switch

gears, BUSBARS, suitable size of inter connecting PVC

copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and

rubber gasket,heavy duty end terminal

connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding

base beams) The panel shall be supplied with

following approved manufacturers with following size.

(B) The standard companies switch gear shall be used

and only manufacturers at CPRI approved factory

(i) with 350mm depth

Item Rate In

Description of Item Quantity Unit Amount

No figures

190 Supplying and erecting triple pole & neutral 440V / 6.00 Rn.mtr 1961.42

500V panel mounting Copper Busbars with four equal

Nos. of electrolyte bus having current density not

more than 1.6 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulating tape

for phase sequence of following current carrying

capacity, erected with necessary bus bar supports

/insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections.(A)

Suitable for 100 Amp. Capacity

191 Providing and erecting ,Fabricating the box type items 120.00 Kg 180.79

made from M.S. Sheet with A.I. supports, wings, doors,

handles other hardware materials as per requirement

design with finishing by three tank powder coating

processed inside and outside painted, erected as

directed including minor civil work.

192 Supplying and erecting Direct - On - Line Starter with 6.00 Ea 2100.80

18 A. rating contactor and with 3.5 Amp. 18A range

directly operated in totally insulated elegant enclosure

for single phase operation up to 3 HP as per IS

complete erected on P.W. Block with necessary

connection. Cat-lll

193 Supplying and erecting approved make panel 6.00 Ea 1275.63

mounting type Digital Voltmeter having 3 digits LED

display, 0 to 750 AC Volts range erected on existing

panel board with all connection, wiring etc .with

manufacturers calibration certificate.

194 Supplying and erecting approved make panel 6.00 Ea 1558.43

mounting type Digital Ammeter having 3 digits LED

display, external CT operated, calibrated for 0 to

Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc

.with manufacturers calibration certificate.

switch for 3 phase AC Supply 500 V on existing panel

board with necessary connections.

196 Providing & erecting L.T. Current Transformer with 18.00 Ea 274.72

bar primary 50/5 to 1000/5 ratio 15 VA burden

erected in existing CRCA box duly secured with

insulating materials connected to the meter

197 Supplying and erecting approved make suitable panel 18.00 Ea 43.43

indicator LED type lamp, lens cover, complete erected

with necessary connections.

198 Providing & erecting open well type horizontal mono 6.00 Ea 10734.28

block pump set with stainless steel body having

following specification

[B] For 2 HP 3 phase open well horizontal mono block

pump set suitable for 200 LPM @ 25 mtr head suitable

for 50 mm dia delivery pipe

199 Providing and erecting ISI marked PVC insulated PVC 120.00 Mtr 104.03

Sheathed Flat flexible Submersible copper cable

approved make of following Size.

(b) 3 Core x 2.5 Sq. mm.

Item Rate In

Description of Item Quantity Unit Amount

No figures

200 Providing and erecting ISI marked PVC insulated PVC 200.00 Mtr 647.41

Sheathed Flat flexible Submersible copper cable

approved make of following Size. (G)3 Core x 25 Sq.

201 Supplying and erecting Fully Automatic hydro 6.00 Ea 46135.79

pneumatic booster system with cast iron housing

Enclosure class IP44 minimum , with built in PTO

motor protection and stainless steel impeller pump,

pump model GRUNDFOS CMB 5-46 series or

equivalent with 24 Liter hydro pneumatic pressurized

tank capacity : 5 m3/hr,Rated head :30 mtr, motor

rating : 1.2 H.P. includes pressure switches, Non

Return Valve, Pressure Gauge, 5 way Brass connector,

with necessary Plumbing work which includes all

required size of pipes, Joints valves, Bypass valve,

labor all accessories required for installation of

pressure pump ( Foundation work and base stand cost

202 Supplying and erecting insulated pair of soft copper 150.00 Rmt 965.56

tubing open or concealed including power and control

cable,necessary PVC drain pipes for Split AC machine

up to 4 TR capacity

203 Supplying & erecting approved make Automatic liquid 6.00 Ea 2355.32

level controller 6A. with sensor testing as per

instruction of Engineer in charge on site complete with

wiring connection with existing wires , with copper

conductor from pump to upper and lower tank.

204 S.I.T.C. submersible pump set for bore of 200 mm. dia. 1.00 Ea 104171.40

Or more having 3 phase motor capacity about 40-45

H.P discharge capacity having . Lifting and Lowering

taken extra.(A) (11 Stage) 930 to 780 L.P.M. discharge

at. the head 154 to 182 mtrs. suitable for 80 mm dia.

delivery pipe

205 Supplying and erecting approved make3 phase motor 1.00 Ea 45476.26

control panel (ATS) made from 16 G. CRCA sheet duly

painted with epoxy power paint inside and outside

with hinged doors and locking arrangement,

consisting, of suitable switch of AC 23 duty with HRC

fuses (Cat.III), starting and running contactors,

overload relay, Automatic water level controller,

Electronic timer with master timer CT operated

switch, phase indicating lamps, single phasing

preventer , water level guard, over load, start, run and

stop push buttons, air cooled auto transformer with

60%, 70%, 80% tapping, Panel to be erected on angle

iron frame grouted on wall as directed., contactors

relays, timer etc. shall be of L & T Siemens / Cutler

Hammer make. (D) Suitable for 40 H.P.

206 Lowering of submersible motor pump set at the depth 1.00 Per Job 2996.67

of following ,complete with required. Nos. and size of

casing pipes erected by means of proper chain pulley

block & pipe wrenches after checking of threads of

each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water (C)Above

Item Rate In

Description of Item Quantity Unit Amount

No figures

207 Lowering of submersible motor pump set at the depth 6.00 Per Job 856.48

of following ,complete with required. Nos. and size of

casing pipes erected by means of proper chain pulley

block & pipe wrenches after checking of threads of

each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water (D)For

Open well Horizontal submersible pump set for

sump well(i) 1 HP to 5 HP

208 Supplying of following size of HEAVY UPVC column 120.00 RMT. 359.56

pipe with coupler and wire lock [B] 50 mm dia

209 Supplying of following size of HEAVY UPVC column 180.00 RMT. 698.92

pipe with coupler and wire lock [D] 80 mm dia

210 Supply of following size of TOP & BOTTOM accessories 6.00 Per Set 1489.75

i.e. Adaptor set (CI) long, pump guard set, starter pipe

Rubber ring for submersible pump & UPVC column

pipe as directed by Engineer - in - charge with

necessary plumbing as desired.[D] 50 mm dia

211 Supply of following size of TOP & BOTTOM accessories 2.00 Per Set 3872.34

i.e. Adaptor set (CI) long, pump guard set, starter pipe

Rubber ring for submersible pump & UPVC column

pipe as directed by Engineer - in - charge with

necessary plumbing as desired [E] 100 mm dia

212 providing and erecting Mains with ISI marked, 1.5KV 210.00 Mtr. 91.91

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

required. (f) One wire 10.00 sq. mm

213 providing and erecting Mains with ISI marked, 1.5KV 48.00 Mtr. 300.98

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

required. (i) One wire 35.00 sq. mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

214 Supply, Installation, Testing & Commissioning of 30.00 PER 44081.45

following size of Grid Tied Solar Power Plant with KW

Solar Panels (ALMM approved): Frame Material :

Anodized Aluminum alloy Frame With Twin Wall

Profile, Front Cover : High Transmission Low-Iron

Tempered Glass (AR Coated), High efficency and

positive power tolerance Pmax: 0/+5, Module

Efficiency should be approx. 19.5%-22%, Normal

operating temperature 45'C, Junction Box with

Waterproof IP67 & MC4 Compatible and Enclosed

with Bypass diodes, 100% Electroluminescence test to

ensure error free Modules, Thep. temp. co-efficient of

the PV module shall equal or better than -

0.45%/degree C. Solar PV modules of minimum fill

factor 75% to be used. Unit Production:- More than

Unit /kw /day (Actual)(1Year Avg) With 10 year

Product warranty and 25 year Linear Power Warranty

includes all mechanical and electrical parameters of

the Solar panel. Modules must be complied to the

DCR(Domestic content requirements).

The Ration of AC to DC is 5:6 for the Installation

capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V

Max efficiency: 97.5% - 98.9%, O/p Frequency:

50/60Hz, Operating Altitude (m) ≤4000, O/p Power

Factor: ~1, O/P THDi: <3%, Operating Tempreture

Range: -25~60°C, Integrated protection of Inverter are

Anti-islanding Protection, Input Reverse Polarity

Protection, Insulation Resistor Detection, Ground fault

protection, Residual Current Monitoring Unit, Output

Over Current Protection, Output Short Circuit

Protection, Output Over Voltage Protection, PV array

string fault Protection. Protection Degree: IP65, User

Interface LCD & APP, Datalogger & Communication:

GPRS / Wi-Fi.

Item Rate In

Description of Item Quantity Unit Amount

No figures

Integrated, Input Reverse Polarity Protection

Integrated, Insulation Resistor Detection Integrated,

Residual Current Monitoring Unit Integrated, Output

Over Current Protection Integrated, Output Short

Circuit Protection Integrated, Output Over Voltage

Protection Integrated, Protection Degree: IP65, User

Interface LCD & APP,Datalogger & Communication:

GPRS / Wi-Fi, Module Mounting Structure: The

mounting (Rectangular pipe / square pipe / circular

pipe) with requisite cross bars, nuts and bolts, etc.

shall be Hot deep galvanized with minimum 80micron

coating. The Rectangular / square /circular hollow

pipe section used for the structure should have a

minimum thickness of 2.0 mm. other than above, the

material thickness should be minimum 2.5 mm. A

certificate of a structural engineer certifying the

strength and stability of the mounting structure to

withstand the weight and wind speed of 150 km/hour

throughout the life span of 25 years of the system,

shall be submitted by the vendors. Hot Dipped

Galvanized steel coils. suitable arrangement for base

plate for foundation , solar panel mounting, the

structure should be suitable for carry the load of solar

panel,wiring, sprinkler system etc. with necessary

foundation work/wall mount, j bolt, anchor fastner etc.

the nut bolt used for installtion of stucture should be

(SS 304) quality.

The ground clearance of the bottom most edge of solar

panel shall not be less than 300 mm to 1200 mm or as

per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should

b. Rafter - The minimum section (thickness) should be

c. Purlin - The minimum section (thickness) should be

40MM * 40MM Balane of System with necessary

Swichgears (Suitabel size and protection of ACDB &

DCDB), inter connecting wiring, earthing system as

per the CEIG drawing approval, lightining arrester

system as per the CEIG drawing approval, all liasoning

work with various gov. dipartment like state nodal

agency,DISCOM & CEIG is included in agency scope

(Excluding All charges namely GEDA Application fees,

Solar connectivity Charges, Meter connectivity

Charges, Meter testing Charges and system

stability/strenthning charges.) (B) Grid Tied Solar

Power System: 7 - 10 kW (3 - phase)

Item Rate In

Description of Item Quantity Unit Amount

No figures

215 S.I.T.C of Decorative Post Top, Top Mounting Light 51.00 Nos 15571.78

decorative luminaire, body made out of Cast & Spun

Aluminium having 310X310mm and

height 650mm with IP 65 optical compartment, lower

bowl in UV stablised frosted acrylic but in CONICAL

SHAPE, integral control gear having

BIS approved Fulham make electronic constant

current driver and LM80 complianed

SEOUL/BRIDGELUX make LED module street light in

complete with all accessories, top mouning, suitable

for 48mm ID pole n pipe.fixture made of pressure die

cast/Aluminum Spun housing with

front opening PC diffuser having IP65 protection,

PF>.90 , Lumen-70/w with High Efficiency LED, THD

LESS THAN 10%, potted driver with 4/6kva surge

Protection. (Decorative Lights, , Nut- Bolt, Clamp, etc.

Included) (Make: Jaquar or Equivalent)

216 S.I.T C of 4.5mtr decorative GI ribbed pole with cast 45.00 Nos 27858.33

iron base, Base Plate Size 250x250x12mm, CI Casting

at Joint & Control Box at the bottom of the

pole for space for Housing MCB & Terminal strip etc.

Specification of Pole Sections:

1st Section - CI BASE decorative part

2nd Section - Ø71mm x 3.2mm, Ribbed pipe

Polyurthane Painted as per your given color shade,

The GI pole should be provided with an in built

junction box to fix 32A connectors and 6A MCB, at the

bottom - the inbuilt box should have a

flush door of suitable size. Pole & it's part are painted

in 3 layer coating in which 1st layer with etch primar,

2nd layer with epoxy primer &

3rd final layer with PU paint.

(Suitable Foundation, Nut- Bolt, Clamp, Base Plate,

Pole MCB etc. Included) (Make: Jaquar or Equivalent)

Total (B)

Total (A+B) Rs.

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and

words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Credit Value of Dismentalled Materials of Amount Rs. 47600.00 shall be recovered from the 1st Running

1 Bill of the Contractor.

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-

2 In-Charge for which no extra payment shall be made.

3 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

4 Income tax TDS will be deducted at a source while making payments of bills

Item Rate In

Description of Item Quantity Unit Amount

No figures

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

5 there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

Gujarat College ( R & B) sub division Navrangpura (R&B) Division

Ahmedabad Ahmedabad

Executive Engineer

C.P. Elect. Division

R&B Deptt., Ahmedabad.