Special repairs to Qtr No 137 1 to 137 8 at KE lines or md accn under GE South Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS)

Dismantling of brick or terracing tiles of single layer on roofs and removal from site, complete all as specified and as directed.

Material and Labour for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish/ demolished material outside defence land, complete all as specified and as directed.

Dismantling of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed.

Material and Labour for plain cement concrete 1:2:4 type B-1 (using 20 mm graded mechanically crushed stone aggregate) as in fixing of hold fasts, copings, bed plates,kerbs or mud stops, lintels upto 1.50m span, plinth courses , seismic and other bands and the like, finished the surface fair and even, including necessary form work complete all as specified and as directed. Note- If reinforced concrete, reinforcement shall be measured and paid for separately.

Material and labour for plain cement concrete 1:2:4 type B-1 (using 20mm graded mechanically crushed stone aggregate) as in surface channels and drains, complete all as specified and as directed.

Material and labour for plain cement concrete, 1:2:4 type B-0 (using 12.5 mm graded mechanical crushed aggregate) for benching, coving, roof kerbs , complete all as specified and as directed.

Material and Labour extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds , mitred /stopped ends etc., complete all as specified and as directed.

Material and labour for brick work with subclass ‘B` old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6), complete all as specified and as directed.

Material and Labour for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) , complete all as specified. ( Note- The serviceable bricks obtained from Serial item No- 1.02 will be used after removing motar, cleaning the bricks with water, etc.)

Cutting chases,pinning inmaking good to facings where required and pointed in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc . cutting not exceeding 10cm girth in brick and making good in cement mortar 1:3 complete all as specified and as directed.

Dismantling asbestos cement corrugated or semi-corrugated sheets including AC ridges etc., as in roof covering, complete all as specified and as directed.

Supplying & Fixing for Pre-painted galvalume aluminuim zinc coating GI based corrugated steel sheet 0.50mm thick, conforming to IS-15961 of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed. Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965.

Supply and fixing mild steel, rolled sections as in main or cross beams, hip and jack rafters, purlin where connected to comman rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to grade Fe-410(Gde 250), complete all as specified and as directed.

Supply and fixing 12 mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces fixed with screws to timber frame work with 6mm thick teak wood edging on all side of plywood . and edging treated with french polish complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise specially provided complete all as specified.

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and as directed.

Supplying and Fixing for factory made 35mm thick, 2nd class HW, plain framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated, complete, all as specified and as directed.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete, all as specified and as directed.

Taking down chowkats or frames with shutter area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and as directed.

Supply and fixing factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet , reinforced with steel square tube , complete all as specified and as directed.

Supply and fixing 30 mm thick Factory Made Solid Panel PVC Door Shutter consisting of frame made out of M.S. tubes of 19mm x 19mm for stiles, and 15mm x 15mm for top and bottom rails. M.S. frame shall be covered with 5mm thick heat moulded PVC sheet ‘C’ channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick PVC sheets for top rail, lock rail and bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles and rails with PVC sheet beading, and joined together with solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s instructions and drawing. The sizes of members of shutters as specified in para 8.34.2.1 of SSR 2009 (Part I), complete, all as specified and as directed.

Supply and fixing framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; angle iron chowkats for door ,barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290-Gde E-165 complete all as specified and as directed.

Supply and fixing mild steel works in bands, straps, supports, stays, bolts, hooks, hold fasts etc, similar articles conforming to Fe-290.Gde-E-165, complete all as specified and as directed.

Material and Labour for mild steel TMT bars of 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete, all as specified and as directed.

Supply and fixing mild steel framed work as in door frame/chowkats, gate of angle or other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides) and hanging also fastening and fixing complete all as specified and as directed.

Supply and fixing factory made mild steel windows or ventilators, fixed type, with glazing bars , complete all as specified and as directed.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 40x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on CECZ Chandigarh drawing No.. TD-219(c) sheet 1/3 to 3/3 and TD-220(c) sheet 1/3 to 3/3 as applicable complete, all as specified and as directed. Note: (i) For the purpose of measurement and payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawing. (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

S & F harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed.

Supply and fixing in replacement mild steel almirah shutters with frame (two leaves), exceeding 1.5 sqm , made of 1.20mm thick mild steel sheet in two leaves as built in furniture in cupboards including locking arrangement with mortice lock of mild steel, vertical type, 65mm size, 2 lever, ISI marked with duplicate keys and handle, etc. (all as per Godrej pattern) including two coats of spray painting over a coat of red oxide primer complete fixed on brick or concrete wall with minimum six numbers of 10mm dia and 100mm long mild steel bolt with washer and nut in cement mortar (1:4) or PCC 1:2:4, type B-0, complete, all as specified and directed by Engineer-in-Charge.

Supply and fixing 200 mm mild steel barrel tower bolt, ISI marked, stove enameled black with bright bolt and fixed, complete all as specified and as directed.

Supply and fixing aluminum anodized, barrel tower bolt of extruded section 150mm long, ISI marked, complete all as specified and as directed.

Supply and fixing 250 mm mild steel sliding door bolt, ISI marked with hasp, staple (bolt type) , stove enameled black, with bright clamp bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified and as directed.

Supply and fixing for butt hinge ,ISI Marked ,100mm size, medium weight, cold rolled mild steel complete, all as specified and as directed.

Supply and fixing for butt hinge, ISI Marked, 50mm size, medium weight, cold rolled mild steel, complete, all as specified and as directed.

Supply and fixing mild steel helical door spring 150 mm long fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and as directed.

Supply and fixing mild steel pressed handle, oval type, stove enameled black, 150mm long, complete all as specified and as directed.

Supply and fixing for ISI Marked 150 mm long, aluminium handle, cast type, anodized, complete, all as specified and as directed.

Supplying and fixing 2nd class hard wood small fitting, such as brackets of any type latch and hinge blocks, shaped door and window stops and the like including all necessary labours ,articles not exc 200 cu.cm each, complete all as specified and as directed.

Supplying and Fixing for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples, complete, all as specified and as directed.

Material and labour 40 mm thick brick tiles laid on and including 15 mm thick bedding layer in cement mortar 1:6 and joints grouted flush in cement mortar (1:3) mixed with 5% crude oil by weight of cement, complete all as specified and directed and flush pointed in cement mortar (1:3), complete all as specified and as directed.

All as per ser item No. 1.01 here-in-above, but except tiles, complete all as specified and as directed. Note- The serviceable bricks tile obtained from Serial item No1.01 shall be reused after removing motar, cleaning the bricks with water, etc.complete.

Material and labour for water proofing treatment with following application over roofs surface complete, all as specified and as directed :- (i) Plain cement concrete 1:2:4 type B1, (using 20 mm graded stone aggregate) 50 mm thick (Average thickness ) as in levelling course,. and surfaces finished even and fair without using extra cement. (ii) Applying oil bound bituminous primer at the rate of 0.4 Litres/Sqm as per IS 3384-1986 on prepared surfaces of roof. Surface shall be kept free, till the primer is impregnated and the solvent oil in the primer get evaporated. (iii) Applying one coat of hot straight run bitumen grade 30/40 (Grade S-35) conforming to IS-73 at the rate of 1.2 Kg/Sqm. (iv) Laying 3mm thick APP polymeric water proofing membrane of weight not less than 3.6 Kg/Sqm, black finish reinforced with non woven polyster matt, wth a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturers instruction including preparation of surface. Note :- The water proofing treatment shall be carried out by the manufacturer or his authorised applicators in terms of clause 11.43 of MES Sch Part-I (2009) and in addition to gurantee as specified in CA, contractor shall also provide Guranttee for water proofing treatment from manufacturer / his authorised applicator, for the water proofing treatment carried out in the work.

Material and labour for machine cut kota stone slab 18-22 mm thick (of size not less than (55 cm x 55 cm) laid in glooring and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting waste, rubbing and polishing (Granite finish) over and including cement screed bed 20mm thick in cement mortar (1:4) base , complete all as specified and as directed.

Material and labour for machine cut kota stone slab 16-18 mm thick laid on vertical surface and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in skirting over and including 10mm thick plaster in cement mortar (1:3) on brick work or concrete surfaces complete, all as specified and as directed.

Material and labour for 18mm thick granite (of any type) work (table rubbed and polished and moulding) in kitchen platforms over and including 15mm thick in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite, complete all as specified and as directed.

Material and labour for PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate), 50mm thick, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 1.20 sqm with 12mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for Glass dividing strips, 3mm thick and 38mm in width inserted in position conform to design complete all as specified and directed .

Material and labour for premium quality, glazed coloured ceramic tiles 300 x 600 x 7mm thick on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match complete, all as specified and as directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.06 sqm and not exceeding 0.11 sqm and 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) , complete all as specified and as directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.18 sqm and not exceeding 0.38 sqm and 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) , complete all as specified and as directed.

Material and labour for premium quality, joint free non skid coloured ceramic tiles, of same description and length as of floor tile but 150 mm height on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified and as directed.

Supply and fixing for 0.80 mm thick, mild steel, plain, black sheet in hearths, covering to door shutters, covering to door chowkats, water tanks, water troughs and funnels, etc. cut to size edges beaded if directed ,holes punched including round headed screws, etc with plain 40mm lap joints or welded/reveted seams including bending , turning up, mitred angles, etc.as required, complete all as specified and as directed.

Material and Labour for vibratory compacted, precast cement concrete, coloured (other than grey), rubber moulded , interlocking designer paver blocks( double glossy) in any and shape, confirming to IS-15658-2006 of 60mm thickness, M-35 grade in path, hard standing, etc. laid over and including 50 mm thick bedding layer of sand over PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregates), 75mm thick sub base finished rough complete, all as specified and as directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. and applying neat cement slurry @ 3.00 kg /sq.m complete, all as specified and as directed.

Taking down cement plaster of any description, thickness and in any position including raking out joints, hacking for key, scrubbing down with water etc , and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound, complete all as specified and as directed.

Material and Labour for rendering 10mm thick in cement mortar (1:3) on ceiling surface and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and Labour for rough cast plaster on brick work or concrete surfaces consisting offine gravel, cement and sand in the ratio of 1:1:1 over 15mm thick under coat in cement mortar 1:3 as specified in clause No. 14.22 of SSR Part-I, mixed with WPC @2% by weight of cement or as per manufacturer’s instructions, complete all as specified and as directed. (Note : WPC shall be measured and paid separately)

Material and labour for preparation of new plastered surfaces and applying three coats of white wash on wall, complete all as specified and as directed.

Material and labour for three coat of white wash on newly plastered surface of ceiling including preparation of ceiling surfaces complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of primer over a coat of 2-3mm thick birla wall care putty , complete all as specified and as directed.

Material and labour for two coat of cement base paint over a coat of alkaline resistant primer on newly plastered surface including preparation of surface of wall complete all as specified and as directed.

Material and labour for preparing new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Material and labour for two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed.

Supply and fixing in repair, water storage tank 500 ltr capacity HDPE triple layer, white coloured, conforming to IS , fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site, complete all as specified and as directed.

Supplying and Fixing for brass tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges, complete, all as specified and as directed. (Make : ESSCO Cat No-1111 or Prayag Cat No. BA-20 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge guarentee certificate for tubular towel rail from manufacturer before claiming payment.

Supplying and fixing (in repair) vitreous China coloured squatting pan of Orissa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including lime concrete, making good to disturbed surface of sub base and flooring with the existing surface and connection to flush pipe complete all as specified and as directed. (Make : Prayag Cat No. 501 or equivalent model in makes mentioned in Appendix 'B' of tender document )

Supply and fixing in repair, vitreous china wash hand basin white flat back of size 550x400mm including CI brackets embedded in wall in CM 1:4, PVC waste pipe, PVC connections and chromium plated waste coupling, etc.,complete all as specified and as directed.

Supplying & Fixing for stainless steel plate rack standard size 600mmx750mm x 200mm complete and fixing with rawl plug and steel screws of wt not less than 5 kg each, complete, all as specified and as directed. (Make : Jainko Cat No. KRJ-2 or equivalent model in makes mentioned in Appendix 'B' of tender document )

Supply and fixing in repair stainless steel sink 1.00mm thick, ISI marked for kitchen with plug, waste PVC pipe, washers including cantilever cast iron brackets connecting union waste pipe with drainage board over all size 940 mm x 460 mm with bowl size 405 mm x 354mm x 203 mm etc, complete all as specified and as directed. (Make :PRAYAG Cat No-1240-D (Solitaire Range) or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing 10 litre capacity, low level, virgin polypropylene cistern, ISI marked, coloured complete with PVC bend/flush pipe and making all connection including taking down existing high or low level unerviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and as directed.

Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and as directed.

Supplying & Fixing for ISI Marked, 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors, complete, all as specified and as directed.

Supplying & Fixing for ISI Marked, 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors, complete, all as specified and as directed.

Fixing only in repairs 15mm dia GI tubes, any grade, to walls and ceilings or laying in floors complete all as specified and as directed. Note: Old tubes reteived from serial item No 1.70 hereinbefore shall be reused in this item.

Fixing only in repairs 20mm dia GI tubes, any grade, to walls and ceilings or laying in floors complete all as specified and as directed. Note: Old tubes reteived from serial item No 1.71 hereinbefore shall be reused in this item.

Supplying and fixing (in repair), bib tap screwed down high pressure, cast copper alloy,fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union, complete all as specified and as directed. (Make : ESSCO Cat No-DLX-511 or Prayag Cat No. 8608 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing (in repair), stop valves, 15 mm dia pipe, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstain head, (concealed type) with long shank heavy body casted cap, screwed both ends for iron pipes or for unions, complete all as specified and as directed. (Make : ESSCO Cat No-DLX-526 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing (as in repair) for brass chromium plated mixer for mixing hot and cold water screwed down high for 15mm bore pipe or union, complete all as specified. (Make : Jainko Cat No-PCT-1 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing ( in repair) stop cock 15mm dia, cast copper alloy, ISI marked, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed. Note : (Make : JAINKO Model No-SVE-1 or equivalent model in makes mentioned in Appendix 'B' of tender document ) (ii)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing ( in repair), stop cock 20mm dia, cast copper alloy, ISI marked, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions complete, all as specified and as directed. Note : (Make : JAINKO Model No-SVE-2 or equivalent model in makes mentioned in Appendix 'B' of tender document ) (ii)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing (in repair), shower arm 240 mm long, light weight , round shape for wall mounted showers with wall flange suitable for 15mm bore pipe including overhead shower rose 125mm dia round shape single flow, complete all as specified and as directed. (Make : Cat No. BS-76 of Prayag or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing (in repair) PVC connections 45cm long and 15mm dia with chromium plated brass nuts and PVC washers on both ends, complete all as specified and as directed.

Supply and fixing ( in repair), PVC waste pipe for wash hand basin/urinals/sink etc, 32mm dia and 80 cm long plain pipe, complete all as specified and as directed.

Supply and fixing in repairs, chromium plated soap dish with fitting fixed with brass screws complete all as specified (Make : Jainko Cat No-SDJ-1 or equivalent model in makes mentioned in Appendix 'B' of tender document )

Demolition and breaking up drain pipes 75/100 mm dia, SGSW, AC, PVC, concrete pipe including fittings, complete all as specified and as directed.

Taking down eaves gutter, SWG pipe line of any size and pattern including all fittings, heads, bends, etc. complete all as specified and as directed.

Material and labour for concrete bed to drain pipes of 150mm bore in PCC 1:4:8 type D-2 using 40mm graded stone aggregates including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Material and labour for salt glazed stone ware drain pipes of 150mm bore laid in trenches and jointed in cement complete all as specified and directed.

Material and labour for 150mm bore dia bends and taper bends, any radius for SGSW drain pipes complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing 75mm dia of outlet, PVC (SWR) floor trap plain with grating including jointing with solvent cement, complete, all as specified and as directed. (Note- UPVC fittings shall be conforming to BS 4515 DIN 19531 and DIN 19534)

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and as directed. (Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

S & F 50mm bore stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof, complete all as specified

Supply and fixing of 110mm bore UPVC (SWR), junction single T (equal or unequal), including jointing with solvent cement complete all as specified and directed.

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and as directed. (Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing in repair, 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Material and labour for pre-cast cement concrete type B-1 1:2:4 (using 20 mm graded mechanically crushed stone aggregate), as in cover slabs for manhole, shelves , landings , crumple joints slabs etc., set in cement mortar (1:4) and finished cement concrete surface even and fair without using extra cement, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, and making good to pipe and rendering cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm size crushed stone aggregate) smooth finished and reforming benching as required of pipe 150 mm dia, complete all as specified

Supply and fixing aluminium fanlight pivot with plate size 25mm x 65mm and suitable for 35mm thick shutters complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing for sheet glass 3mm thick, ordinary quality , in square not exceeding 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed.

Supply and fixing for pre-painted Galvalume Aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in a roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

SCHEDULE A PART II (INTERNAL ELECTRIFICATION)

Taking down Ceiling / wall fan of any sweep, dismantling blades and removing to the MES store for reuse complete, all as specified and as directed.

Taking down carefully by unscrewing from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings , bulk head fittings, tube light fittings and regulators , etc. for reuse at site or carrying to the store and refixing in the same location after civil construction work will be over ( to be measured only when found serviceble in all respect complete for reuse)

Hanging only ceiling/wall fan and connecting up including provision of three core flexible cable 23/ 0.0076 size from ceiling rose to connector of fan , complete all as specified and as directed.

Refixing only serviceable tube light fittings/bulb fittings obtained from Ser item No. 02 including provision of 3 core copper conductor flexible cable of size 23/0.0076 from ceiling rose to connector of light point, complete all as specified and directed by Engr-in-charge.

Material and labour for point wiring with1.50 Sqmm single core PVC insulated, unsheathed cable HFFR / ZHFR (Zero Halogen fire Retardant), 1100 Volt grade with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 25 mm dia with accessories, concealed on wall /ceiling and including provision of 1.50 Sqmm single core PVC insulated, unsheathed cable HFFR / ZHFR (Zero Halogen fire Retardant),1100 Volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS -5139 ( pt-I ) OF 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlet ,fan, regulator etc. with brass screws and brass washers and making good the disturbed surfaces per existing for one light/fan point controlled by one switch complete all as specified and directed. Notes :- (i) Switch, socket and fan regulators to be measured and paid for separately. (ii) PVC Conduit conforming to IS 9537 part I & III. (iii) All chases will be cut by chase cutter only.

Description all as per Srl item No .3.05 here in before but for socket outlet point 5 Amp on Independent board.

Description all as per Srl item No. 3.05 here in before but for socket outlet point 5 Amp on same board.

Description all as per serial item No. 3.05 above but with 2.5 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified and as directed.

Supply and fixing switch piano 5 Amps, flush type, single pole, one way, 230 volt , AC supply, ISI Marked, complete all as specified and directed.

Supply and fixing switch piano 15 Amps, flush type, single pole, one way, 230 volt , AC supply, ISI Marked, complete all as specified and directed.

Supply and fixing socket outlet 3 pin 6 amps, 230 volt. flush type, ISI Marked complete all as specified and directed.

Supply and fixing socket outlet 2 in 1, 6 pin 5 /16 Amp and multi pin flush type, complete all as specified and as directed.

Supply and fixing bulk head light fitting, 10 watt, energy efficient with and including lamp 10 watt with provision of 2/3 core PVC copper conductor cable 0.5 Sqmm size from ceiling rose to light fitting complete all as specified and directed.

Supplying & fixing indoor decorative LED Tube with opal diffuser tube light fitting including LED tube 20 watt high efficient aluminium housing with clear and milky diffuser and connecting to ceiling rose using PVC sheathed and insulated three core copper conductor cable of size 0.50 Sqmm including all accessories for fixing arrangement for fixing the light fitting to walls / ceiling surface complete all as specified and directed.

Taking down Geyser including electrical and water connection complete of any type and size and deposit to MES store for reuse and re-fixing including electrical and water connection and grouting etc complete all as specified and directed.

Taking down old unserviceable point wiring of any type and size complete all as specified and directed.

Note:- Amount of credit of Rs. 1,07,036.00 for retrieved materials is mentioned in Schedule of Credit Page No. 99R of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/S JAISANT CONSTRUCTION CO.

Gupta Enterprises

Sham Sunder Bansal