SPECIAL REPAIRS TO BUILDING NO T69 AND T156 OF BSO YARD AT SECTOR C MAKARPURA UNDER GE(ARMY) BARODA

Amount

Dismantling asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings

Dismantling structural steel work including doors, gates but excluding framed truss etc

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410 W(Gde E-250 Quality B)

Erection and refixing only Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Note:- Serviceable Steel obtained from Item No 3 above shall be reused as directed by Engr- in- Charge).

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified.

S&F 2mm thick (White/coloured)Fibre glass reinforced translucent corrugated/Plain sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall,gate etc.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for preparation of new steel surfaces of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for preparation of old steel surfaces of any description over 10cm width or girth and apply two coats of synthetic enamel paint complete all as specified.

Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each and making good disturbed portion to match with existing

Taking down shutters of any description exc 1 sq. m and n exc 2 sq.m each complete

S & F powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M & L for 4.0mm thick figured glass, n.exc 0.5 Sqm each pane and glazing with rubber beading or with glazing clips, all as specified and directed.

M & L for 4 mm thick sheet glass n.exc 0.5 Sqm each pane ordinary quality and glazing with rubber beading or with glazing clips, all as specified and directed.

M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type on both sides veneered both side with decorative choice laminate type 1 (factory laminated),including 6mm thick external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE.

M&L for two coats of synthetic enamel paint to old wooden surfaces of any description, not otherwise described over 10cm width or girth complete.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised staples complete all as specified and directed.

M & L for 100 mm butt hinges stainless steel grade 202, 14 gauge thickness medium weight fixed with pressed steel door frame / pvc door frame with screws.

S&F 300mm aluminum anodised sliding door bolts, with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alluminium alloy complete all as specified and directed.

S&F 150 mm extruded aluminum alloy handles, fabricated type anodized complete all as specified and directed.

S & F 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed, all as specified.

M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of 2mm average thick birla/equivalent wall care putty and one coat of chalk whitening primer complete

M & L for preparing old decorated surfaces of wall and applying one coat cement base paint on external wall.

M & L for preparing old decorated surfaces of wall and applying one coat of oil bound distemper complete all as specified.

M & L for preparing old decorated surfaces of wall and applying two coats of white wash complete all as specified.

S & F solid PVC door frame of size 50mmx47mm made out of 5mm Prelam colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing. The door frame shall be tied to the wall using 75/100mm long MS screw as directed.

S & F Factory made solid panel Prelaminated PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. M S tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail, panelling of prelaminated colour PVC sheet both side to be fitted in the MS frame welded/sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement.

Demolition of Brickwork or stone/boulder masonry, built in cement/cement lime mortar including all quoins, arches, pillars, ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling etc. all as specified and directed.

M&L for brickwork with sub class ‘B’ old size bricks straight or curved on plan exc 6 m mean radius built in CM 1:6

Taking down cement plaster on brick or stone walls / ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete

M & L for 10 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement all as directed.

M&L for Rendering 15 mm thick in two layer on fair faces of brick work or concrete surfaces of wall 5 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 smooth without using extra cement (WPC will be measured separately).

M&L for PCC 1:3:6 type C-1 using 20mm graded aggregate in coping,kneelars,apex stones,bed plates,kerb etc water troughs and the like including weathering, slightly rounded for chamfered angles and troathing including necessary form work complete all as specified and as directed.

Welding in repair n. exc 2.5cm in length , thickness of metal to be welded exc 6mm but n.exc 9mm complete all as specified and directed.

Welding in repair exc 2.5cm but n.exc 5cm in length thickness of metal to be welded exc 6mm but n.exc 9mm complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where directed complete all as specified or directed by the EIC

M&L for cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate 100mm thick as in sub base to flooring including necessary form work complete all as specified.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate 75mm thick as in hard standing including necessary form work and finishing surface even and smooth without using extra cement complete all as specified.

M&L for Machine pressed, precast plain cement concrete Interlocking paver block, factoty made( with grey cement and no pigment) conforming to IS-15658-2006, 60mm thickness M-35 grade complete.

M & L for 50mm thick sand cushioning for laying of interlocking paver block including spreading and levelling all as specified

M&L for machine cut kota stone slab flooring 20-25mm thick over and including cement screed base 15 mm thick in cement morter1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar.

M&L for non skid coloured ceramic tile 7 to 8mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match including 15mm thick screed bed or bedding layer of mortar for laying floor finishes with CM 1:6.

M&L for Glazed ceramic coloured walls tiles in vertical surfaces 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering for backing coat on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles.

M&L for Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble to match over and including screed bed or bedding layer of mortar including 15mm thick for laying floor finishes with CM 1:6.

Cleaning the surface with wire brush, detecting sources of leakages and removing/taking down unsound treatment/surface and M&L for carrying out non destructive, waterproofing treatment to sunken portion of slab, floor, chajjas and walls of bath, WC, WHB and floor traps (combined unit) by using construction chemical method as hydrophobic PU grouting, etc, with first course of injection MDI based PU foam and second course of injection PU plain all as per manufacturers instruction, etc, complete and as directed . The PU foam shall have 100% solids and solvent free and shall expand 30-40 times its volume at liquid stage in presence of water, the PU plain injection shall have minimum 100 CPS viscosity and shore hardness minimum 50. Make: PIDILITE (Dr Fixit) or equivalent.

Grubbing up tree trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes, trunk around periphery of building upto 2m and leveling off ground periphery of building upto 2m, stacking of serviceable material and removing of unserviceable material to a distance n exc. 500 m and clearing site

S & F 15mm bore high density UPVC pipe of pressure rating 6kgf/sqcm with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge.

S & F 25mm bore high density UPVC pipe of pressure rating 6kgf/sqcm with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge.

M&L in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete type B1, 1:2:4 for 75mm bore.

S & F in repairs plastic seat cover white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device

S & F in repairs Vitreous China wash down water closet pan pedestal pattern (Europian type) (excluding flushing cistern and flush pipe) plastic seat black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device.

S & F in repairs PVC valvless syphonic action flushing cistern low level white of 10ltrs capacity with inlet ball valve float and handle including bracket.

S&F in repairs health faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs PVC connection 600mm long of dia 15mm complete.

S&F in repair Vitreous China wash hand basin, angle back 550 x 400mm white excluding taps, waste chains and plugs and porcelain stopper but including CI bracket and nut bolts as per maufacturers instructions.

S&F in repairs 32mm dia flexible waste pipe for urinal, wash basin and kitchen sink for length exc. 1m not exc 2m complete.

S&F in repair PTMT waste coupling of 32mm dia (half or full thread) including taking down old coupling of any description complete all as specified and directed.

S&F in repairs 15mm dia stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle for iron pipe

S&F in repairs, 15mm bore bib taps fancy type chromium plated cast copper alloy with capstan heads, screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm bore Pillar taps, cast copper alloy, with capston heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 110mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall as in waste/soil pipe complete all as specified and directed

S&F in repairs 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall as in waste/soil pipe complete all as specified and directed

S&F in repairs 110 mm dia PVC (SWR) bends of any radius with access door complete

S&F in repairs 75 mm dia PVC (SWR) bends of any radius with duck foot or heel rest fitted with oval access door complete.

S&F in repairs including disconnecting tanks, 1000 ltrs rotational moulded double layred, polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

S&F 25mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 142 gms) complete all as specified and directed. Make : Prayag & equivalent.

M & L preparation of new plastered surfaces of walls and applying two coats of cement based paint over a chalk whitening over a plastered surface complete all as specified.

Taking down carefully copper / Aluminium point wiring including (light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, Batten holders, shades conical fan regulators, light or power sockets etc) removing materials from site and making good disturbed surfaces of walls roofs etc all as directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

M&L for concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLS cable 1100 volts grade, conforming IS 694 & color code in conduit system of wiring, drawn in including medium grade PCV conduit not less than 20 mm dia concealed, including cutting chases, finising of slote by means of cement mortor making good to the existing surface of the wall & touching with the existing colour of wall with three coats and making good disturbed surface complete, sunk in pressed steel terminal boxes of required size not less than 3.0mm thick factory made and factory painted with top cover 3.0 mm thick plastic laminated sheet6 fixed with brass screw and washer with all accessories including single core solid conductor copper 1.5 sqmm size solid PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified for following:-

One light/fan/bell point controlled by one switch 6 Amp one way

One 3 pin switch socket combination 6 amp on the independent board.

All as described as per item No 75 above but point wiring with 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheathed FRLS cable 1100 volt grade and 2.5 sqmm PVC insulated and unsheathed FRLS cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on independent board.

S & F switch piano flush type single pole, one way 6amp,

S & F switch socket combination 5 pin 6 amp,

S & F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal.

S & F fan regulator electronic type 100Watt 20V-50Hz as directed by Engr-incharge,

S & F ceiling rose surface bakelite three terminal 65 x 50 mm three terminal 230 volts ISI marked.

Taking down U/S FTL and Supply and fixing of 4' 18W LED Tube With Batten with system lumen output of 1800 lumens. System Efficacy should be > 115lm/ W. The Luminaire Should have Cool Daylight Color temp of 6500K & CRI>80.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Surge Protecton of 3KV.All the Photometrical & Electrical parametrs must be supported by LM79-08 test report from NABL Accridiated LAB OR UL, R9 Value > 0. Lamp starting time is not more than 1 Sec. The LED tube light conforms to applicable IS.Make of LED From Philips/Crompton/ Wipro. Housing of Batten should be made from Single piece powder coated CRCA sheet steel.Similar to Crompton LDSL 18-CDL with Master TLED 18W 1800 Lumens.

S & F MCB DB factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V for fixing of MCBs/ Isolators/ RCCBs etc complete as following:-

TPN 4 way

SPN 8 way

S & F MCB TPN 40 Amps 10 KA rupturing capacity. Make Legrand or its equivalent in Schnieder/ABB.

S & F MCB SPN 40 Amps 10 KA rupturing capacity. Make Legrand or its equivalent in Schnieder/ABB.

S&F MCB SP 5 to 30 Amp 240 Volts

M & L for sub main wiring concealed conduit using two single core 6 Sqmm fire retardant PVC insulated and unsheathed cable with copper conductor 1100 volts grade ISI marked drawing in and including accessories like bends, tee, etc fix on wall and ceiling and connecting to earth dolly and including 6 Sqmm earth wire, PVC insulated & unsheathed incl necessary cutting chasing all as directed. Note :- Two run of main wire and one run of earth wire incl conduit shall be measured as one length

M & L for sub main wiring concealed conduit using two single core 10 Sqmm fire retardant PVC insulated and unsheathed cable with copper conductor 1100 volts grade ISI marked drawing in and including accessories like bends, tee, etc fix on wall and ceiling and connecting to earth dolly and including 10 Sqmm earth wire, PVC insulated & unsheathed incl necessary cutting chasing all as directed. (For 3 Phase Supply) Note :- Two run of main wire and one run of earth wire incl conduit shall be measured as one length

S&F in repair energy efficient 5 star rated ceiling fan 1200mm sweep, single phase 230/240 volts AC and connecting up to including provn of porcilin connector and flexible three core copper conductor of size 23/0.0076 from ceiling rose or connector to ceiling fan and testing on completion, complete all as directed by engr-in-charge.

S & F wall security light LED type 36 watt complete with GI bend 1.2 mtr and fixing on wall/pole with clamp, nut & bolt complete all as directed and specified by Engr-In-Charge.

Supply and fix Exhaust Fan steel body 380mm size single phase 1400 RPM max air 3250 M3/Hr free delivery 1910 sound level 60-65 complete with louvers

Badri Electricals (BID ID -3066366)