REPAIR AND MAINT OF LT OH UG LINE APFC PANELS LT SWITCHGEARS AND REPAIR AND MAINT OF SOLAR WATER HEATER AND GEYSER CEILING FANS EXHAUST FANS AND ELECTRICAL FITTINGS IN MD OTM ACCN AT PALAMPUR MIL STN UNDER GE PALAMPUR

Amount

Excavation in trenches in any type of soil not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for laying of cables, erection of poles,struts, stays etc and getting out all as specified and as directed by Engr-In-Charge.

All as per item No 1 above here in before but in hard/dence/PCC/Floor/road

Returning, filling in including spreading, levelling,watering and well ramming excavated soil in layers not exceeding 25 cm thick each , filling back in trenches after cables have been laid and tested, poles,stays,struts hane been erected and tested complete all as specified.

Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed by Engr-in-Charge.

M&L for laying in trenches burnt brick sub class 'B' for cable protection laid adjacent to each other length wise perpendicular to the central axis of cable complete all as specified.

Dismantling of old damaged Aluminium conductor off sizes from existing over head lines complete all as specified and directed by Engr-in-Charge.

All as per item Srl No 7 as above but GI wire/stay wire.

Dismantling / taking down old unserviceable pin/shackle type insulator any type / size.

Dismantling U/S any size of cross arms from pole /structures and fencing post,struts etc. complete all as specified and directed.

M&L for ACSR conductor off sizes drawn over for over head lines fixed to insulators with binding wire after allowing specified sag complete all as specified and as directed by Engr-in-Charge

M&L for GI wire 4mm dia as continuous earth wire, guarding and craddles to OH line including binding wire complete all as specified and as directed by Engr-in-Charge.

Supply & fixing pin type porcelain vitreous insulator 100 mm height and 65 mm dia for 1100 Volts grade including galvanised mild steel spindle, one nut and two washers complete all as specified.

Supply and fixing shackle type insulator porcelain vitreous white,brown and green of size 75 mm heaight and 90 mm dia incl galvanised MS straps 31x3 mm size ,washers,insulator bolt 12 mm dia and nut for working pressure 1100 Volts grade complete all as specified.

M&L for work as in cross arms, support, bracings, stiffeners, clamps channels fabricated from structural steel including nuts, bolts and washers welding, bending cold or hot drilling holes for bolts in any shape or size all as directed including two coats of aluminium paint over a coating of red oxide primer all as directed by Engr-In-Charge.

Supply and fixing PVC moulded rigid type LT Line spacers suitable for 3 lines OH system complete all as specified and directed.

Supply and fixing PVC moulded rigid type LT Line separator suitable for 4 lines OH system complete all as specified and directed.

Taking out from trenches / floors/road/wall/pipe/pole LT cable of any size/description and removing from site incl making good the disturbed surfaces to match with existing surface all as directed.

Supply & laying of LT UG cable XLPE insulated armoured heavy duty elect cable with stranded aluminium conductor 1100 volts grade cross section area 95 Sqmm 3.5 core laid in trenches/ fixing on panels/walls/poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing complete all as specified and directed. Note: (i) Cable joint shall be measured and paid separately.)

All as per item No. 19 above but of cross sectional area 70 Sqmm, 3.5 core.

All as per item No. 19 above but of cross sectional area 50 Sqmm, 3.5 core.

All as per item No. 19 above but of cross sectional area 35 Sqmm, 3.5 core.

All as per item No. 19 above but of cross sectional area 25 Sqmm, 3.5 core.

All as per item No. 19 above but of cross sectional area 16 Sqmm, 4 core.

All as per item No. 19 above but of cross sectional area 10 Sqmm, 4 core.

M&L for Cable route indicator showing "LT Cable" and rout of cable with arrow made of CI in suitable eliptical/round shape and fixed on angle iron 40x40x6mm, 800mm long painted in Blue Colour with two coats of synthetic enamel paint cover a coat of red oxide primer duly embaded in PCC block (0.40x0.40x0.40)mtr including in ground and 0.15mtr above ground lable complete all as directed and specified.

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material (Epoxy Based) and accessories suitable for 3½/ 4 core XLPE armoured Al conductor cable of size 25 to 50 sq mm complete all as specified and as directed.

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material (Epoxy Based) and accessories suitable for 3½/ 4 core XLPE armoured Al conductor cable of size 70 to 95 sq mm complete all as specified and as directed.

M&L for laying GI PIPE light grade 50mm dia for cable protection in road/floor complete all as specified and directed.

M&L for laying GI PIPE light grade 80mm dia for cable protection in road/floor complete all as specified and directed.

M&L for scraping, scretching, cleaning the old paint, preparation of the surface for repainting. Painting LT 09 Mtr long steel tubular pole with two coats of aluminium paint and writing pole Nos. all as directed by Engr-In-Charge

M&L for Trimming /chopping and cutting of branches in each tree of any girth which are coming across the over head line LT up to 3 m both sides from the centre of conductior as required and removing the same from site of work complete all as directed by Engineer-in-Charge.

Material and labour for removal green vegetation and dressing around the sub stn bldg/2/4 4 pole structure / plinth/copping/PCC hardstanding up to 1.5 mtr etc including disposal of vegitation /material up to 50 mtr distance from the site and levelling/surfacing the ground all as specified and as directed by Engr-in-Charge.

Demolition of concrete (coping of steel /PCC pole/Road) of any description and in any position complete all as specified and directed.

M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles,earth pit ,including provision of necessary form work, finishing even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M & L PCC 1:3:6 type C2 using 40mm graded stone aggregate as in road cutting filling, foundation, fencing post , struts etc. complete all as specified and directed by Engr - in Charge.

Supply and fixing in replacement of MCCB 400 Amp rating,4-pole 415V, 50 Hz breaking capacity 36 KA, Adjustable & fixed magnetic setting type complete all as specified and directed.

Supply and fixing in replacement of MCCB 250 Amp rating,4-pole 415V, 50 Hz breaking capacity 36 KA, Adjustable & fixed magnetic setting type complete all as specified and directed.

Supply and fixing in replacement of MCCB 200 Amp rating,4-pole 415V, 50 Hz breaking capacity 25 KA, Adjustable & fixed magnetic setting type complete all as specified and directed.

Supply and fixing in replacement of MCCB 125 Amp rating,4-pole 415V, 50 Hz breaking capacity 16 KA, Adjustable & fixed magnetic setting type complete all as specified and directed.

Supply and fixing in replacement of MCCB 160 Amp rating,4-pole 415V, 50 Hz breaking capacity 25 KA, Adjustable & fixed magnetic setting type complete all as specified and directed.

Supply and fixing in replacement of MCCB 100Amp rating,4-pole 415V, breaking capacity 16KA complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmX60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the plate not than 1.5mtr below normal ground level connected to GI earth strip of size 32x6mm dia by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC M-10(Nominal mix) using 20mm graded stone aggregate, 50mm thick earth pit cover of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with MS TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape, PGI funnel, wire mesh and 20mm bore GI water pipe medium grade and 40mm bore medium grade GI pipe for protection of earth strip from plate to main switch board, common salt, charcoal dust including testing on completion complete all as specified and as directed all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost all as directed by Engr-in-Charge. (Note: GI strip & GI pipe beyond 7.5Mtr length from earth electrode shall be measured and paid separately).

All as per item Srl No.43 here in before but by using GI wire 4mm dia as earth lead & 15mm bore medium grade GI pipe for protection of earth wire from plate to main switch board complete all as specified and directed.

M&L provn of Earthing complete with Copper earth plate electrode 600 x 600 x 3 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the plate not less than 1.50 M below normal GL, connected to copper earth strip 25 x 3.15 mm upto 7.5 mtr protection pipe by means of copper bolts, nuts, check nuts & washers incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 40mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No.3 of SSR Pt-I specification. Note :- (i) The excess requirement (if more than 7.5 Mtr) of copper strip, GI protection pipe 40 mm dia and their joints for connecting upto the test point will be measured and paid separately) (ii) The excavation exceeds if any of the above will be deemed to be included in the item rate.

M&L GI strip of size 32x6mm as earth continuity conductor burried in ground or drawn in pipe or fixed to wall on saddle complete all as specified and directed.

M&L copper strip 32x3.15mm thick as earth continuity conductor fixed to wall or burried in ground/hard standing in & including GI protection pipe complete all as specified & directed.

M&L sheet metal enclosure for feeder piller box or in replacement of rusty panel doors by providing sheet metal enclosure made out of CRCA plain sheet duly powder coated, dust and vermin proof, water proof,with locking arrangement and fabricated to shape & size as per existing including welding work for fixing complete all as as per site requirements and as directed.

M&L 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1m apart including 4mm dia suspension GI wire with stranded conductor 10 sqmm twin core cable flat or circular including taking down old unserviceable cable and stacking at site, complete all as specified.

M&L repair to APFC panel by cleaning of dust inside with blower, cleaning of moving part/contract from CT cleaner, contactors ,relays and capacitor of loose parts/electrical wiring, complete testing of APFC relay with necessary settings with CTs /load adjustments to match with the APFC load management system complete with replacement of burnt/worn out unserviceable components /burnt wires thimbles /lugs etc for APFC panel capcity 50 KVAR to 150 KVAR complete all as specified and directed. Note : All unserviceable parts shall be measured and paid seprately .

Supply and fixing in replacement of Auxillary contractor 1 NO+1NC TP 415 volts suitable for 10 KVAR rating for existing APFC panel complete all as specified and directed.

Supply and fixing in replacement of Auxillary contractor 1 NO+1NC TP 415 volts suitable for 20 KVAR rating for existing APFC panel complete all as specified and directed.

Supply and fixing in replacement of CT's suitable for Ampere meter 100/5A ratio for existing APFC panel complete all as specified and directed.

Supply and fixing in replacement of CT's suitable for Ampere meter 200/5A ratio for existing APFC panel complete all as specified and directed.

Supply and fixing automatic power factor controller relay 8 Steps as per Cat Part No RG-8T complete all as specified and directed

Supply and fixing automatic power factor controller relay 12 Steps as per Cat Part No RG-12T complete all as specified and directed

Supply and fixing automatic power factor contactor 73 Amp 3 pole 415 volt, 37 KW,AC3 as per existing Cat Part No complete all as specified

Supply and fixing automatic power factor contactor 50 Amp 3 pole 415 volt ,22 KW,AC3 as per existing Cat Part No complete all as specified

Supply and fixing automatic power factor contactor 40 Amp 3 pole 415 Volt ,18.5 KW,AC3 as per existing Cat Part No complete all as specified

Supply and fixing automatic power factor contactor 25 Amp 3 pole 415 volt ,11 KW,AC3 as per existing Cat Part No complete all as specified

Supply and fixing Fixed capacitor 3 phase, 440 volts supply system, MD-XL type 30 KVAR .

Supply and fixing Fixed capacitor 3 phase, 440 volts supply system, MD-XL type 20 KVAR

Supply and fixing Fixed capacitor 3 phase, 440 volts supply system, MD-XL type 15 KVAR

Supply and fixing Fixed capacitor 3 phase, 440 volts supply system, MD-XL type 10 KVAR .

Supply and fixing Fixed capacitor 3 phase, 440 volts supply system, MD-XL type 5 KVAR

Supply and fixing copper bus bar chamber suitable for 100 Amp TPN with 4 outgoing ways , IP-42 complete all as specified

M&L for painting for sheet metal enclosure of LT panels/Installation boards with two coats of synthetic enamel paint as directed colour after scraping of old paint & preparation of surface and applying a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement voltmeter for LT panel Square dial of size 96x96mm digital type complete all as specified and as directed. (Note: Existing meter analough type and large in size, hence any modification in the wiring,and panel sheet enclosure is deemed to be inclusive in the scope of work).

Supply and fixing in replacement Ammeter for LT panel Square dial of size 100 mm digital type complete all as specified and as directed. (Note: Existing meter analough type and large in size, hence any modification in the wiring,and panel sheet enclosure is deemed to be inclusive in the scope of work).

Supply and fixing in replacement indicator lamp assembly in red,yellow & blue colour for LT panels complete all as specified and as directed.

Supply and fixing 4 pole change over switch 200 Amp alongwith connected accessories complete all as specified ,directed & as per site requirement

Supply and fixing 4 pole change over switch 100 Amp alongwith connected accessories complete all as specified ,directed & as per site requirement

Supply and spread graded coarse aggregate of 40mm to 63mm nominal mixed size around outdoor transformer and two/four pole structure /Panel after cleaning and leveling of work area complete all as specified and directed.

Supply and fixing Double Wall Corrugated (DWC) pipe of size 63mm outer dia and 50mm inner dia confirming to IS:14930 Part-II including necessary pipe fittings such as couplers, end caps, bend etc. including fixed to wall/roof /pole/trench as required with suitable clamps for cable protection complete all as specified and directed.

S&F glow sign boards made out of acraylic sheet 2 mm thick fitted on front side of the box and GI sheet 24 SWG for making installation mounted on a 25x25x4mm angle iron frame including tube light fitting of suitable size prewired complete with stranded accessories size of board is 150cmx0.60cmx0.15cm duly written in bold capital letters of size as suitable for sign board (Font as explained and approved by engineer in charge ) including necessary cable connection for supply to board complete as specified and directed by the engineer in charge. (Note Sign board and name which to be written on board shall got approved from the engineer in charge before execution.)

Taking down geysers of any type and capacity due to rusting of bolts/seepage of wall, S&F heavy duty pin type fastener 4 inch long and making necessary inlet/outlet and electric water supply connections from existing source of geyser complete all as specified and as directed.

Inspection, checking adjustments and minor repairs of storage water heater 25/35/50Itr capacity of any type any make vertical/ horizontal type which includes the following:- (a) Inspection, taking out of drain plug & dewatering and re-fixing the same complete all as directed. (b) Checking water tightness of storage tank. (c) Checking stop cocks with outlet/inlet pipe of geysers, pressure reducing valves etc to ensure free movement of water and easy functioning of parts. (d) Inspecting over flow vent pipe connections to ensure water-tightness and proper flow. (e) Checking and correct earth continuity of electrical items. Checking functioning of heating element and correct setting adjustment of thermostat up to 55° C. (f) Adjustment of reducing valves, checking of dead weight type high pressure release valve. (g) The cost of spare parts required for repair & maintenance of geysers covered under this item shall be measured and paid separately under the relevant item as supply only. Make of geysers covered under the scope of work:- Sidhson, Bajaj, Racold, Khaitan, Crompton, orison, Ditz Premier, Peeco, Empire, Shakti, Sahas & Konark. Note:- Irrespective of the Number of complaints, work against this item of BOQ shall be completed within 03 days after handing over the Complaint slip failing which recovery @ Rs 200.00/per geyser per day for delay shall be effected from the contractor payment.

Supply only heating element, 2 KW 230 volts, ISI marked suitable for 25/35/50 ltrs geysers of any make complete all as specified and as directed. Make:-Khaitan , Model no : HI-LIFE 25 Ltr

Supply only heating element, (Triangle type) 1.5 KW 230 volts, ISI marked suitable for 25/35/50 ltrs geysers of any make complete all as specified and as directed. Make:- Bajaj / Racold/Theta

Supply only heating element, (Triangle type) 2 KW 230 volts, ISI marked suitable for 25/35/50 ltrs geysers of any make complete all as specified and as directed. Make:- Bajaj / Racold/Theta.

Supply only heating element, (Round type) 1.5 KW 230 volts, ISI marked suitable for 25/35/50 ltrs geysers of any make complete all as specified and as directed. Make:-Bajaj / Racold/Theta.

Supply only heating element, (Round type) 2 KW 230 volts, ISI marked suitable for 25/35/50 Itrs geysers of any make complete all as specified and as directed. Make:- Bajaj / Racold /Theta

Supply only thermostat switch for geysers of 25/35/50 Itrs capacity (ISI marked) complete all as specified and as directed. Make:- Khaitan , Model no : HI-LIFE 25 Ltr

Supply only 6 hole base assembly, compatible to existing geyser, with inlet and thermostat pipe with drain plug inclusive of clamps for holding the element with nuts, bolts and gasket complete all as specified and as directed.

Supply only indicator lamp for geyser of any type colour green & red complete all as specified and as directed.

Supply only 6 holes stainless-steel inner tank of minimum 20 gauge sheet rated pressure not less than 7 kg/sq.cm suitable for 25 Itrs capacity geysers (wt not less than 3.75 kg) as per sample complete all as specified and as directed.

Supply only 6 holes stainless-steel inner tank of minimum 20 gauge sheet rated pressure not less than 7 Kg/sq.cm suitable for 50 Itrs capacity geysers (wt not less than 5.25 kg) as per sample complete all as specified and as directed.

S&F in repairs PVC connection for hot/cold water made of double layer nylon braided and fabric at a pressure of 6 kg/sq. cm at both ends, 450mm long, heavy duty with CP brass adopters, washers, suitable for 15mm bore pipe complete all as specified and as directed. MAKE:- PRAYAG/ POLYTUFF/ SHAKTI

S&F in repairs PVC connection for hot/ cold water made of double layer nylon braided and fabric at a pressure of 6 kg/sq. cm at both ends, 600mm long, heavy duty with CP brass adopters, washers, suitable for 15mm bore pipe complete all as specified and as directed. MAKE: PRAYAG/ POLYTUFF/ SHAKTI

S&F in repairs bib taps, cast copper alloy, with crutch or butterfly handle chromium plated, fancy type, screwed down, screwed for 15mm bore iron pipe, IS marked, complete all as specified and as directed.

Dismantling carefully solar storage water heating system of any capacity, any type for following works with testing and re-fixing the same in original position making all water/ electric connection to entire satisfaction of Engineer-in-charge after repair as under:- (a) Inspection, opening, of all parts, descaling, washing of inner tank with chemical solution and cleaning of outer cover storage tank. (b) Checking water tightness of storage tank after cleaning. (c) Checking and correcting earth continuity of electrical items. (d) Adjustment of reducing valves, checking of dead weight type high pressure release valve and visual check of fusible plug for its intactness. (e) Nipples, elbows, sockets, reducers, float valve, and other minor accessories shall be deemed to be included in the quoted rates. Note: Supply and fixing of Spare parts, wiring etc shall be measured & paid separately.

Supply and fixing in repairs heating element, 3.00 KW 230 volts, ISI marked suitable for solar geysers tank of any make complete all as specified and as directed. Make:- USHA/ Bajaj Recold/Daspas

Supply and fix in repairs thermostat switch for solar water heater (ISI marked) any make and size complete all as specified and as directed. Make:- USHA/ Baja/Theta/Elcon.

Supply and fix in repairs glass of heat collector for solar water heater 200/300/400 litre capacity complete all as specified and directed.

Supply and fix in repairs tuffen glass of heat collector for solar water heater 200/300/400 litre capacity complete all as specified and directed.

Repair and welding to stainless steel water storage tank of solar storage water heating system of any capacity 100 to 500 LPD, to prevent any type of leakage at site with testing and re-fixing the same in original position making all water / electric connection to entire satisfaction of Engineer-in Charge after repair.

M&L for repairing/replacement of unsv/damaged tube of any type any material complete and refixing same/ new as required at site and as directed by Engr-in-charge.

Taking down old unserviceable electric water geyser, S&F new electric water storage Heater (vertical type Geysers) 50 Ltrs BEE RATING 5 STAR, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making necessary inlet /outlet water connection for Geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, thermostat cut off etc.complete all as specified and as directed.

Taking down old unserviceable electric water geyser, S&F new electric storage Heater (vertical type Geysers) 25 Ltrs BEE RATING 5 STAR, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making necessary inlet / outlet water connection for Geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, thermostat cut off etc. complete all as specified and as directed.

Taking down ceiling fan ,any size and sweep from its position after disconnecting electrical connection and transport it to workshop for servicing,dismantling for servicing including removal of bearing,bushes, condenser, connector, flaxible cord,split pin etc if required removing old grease and refill fresh, lubricating bushes alongwith new washers, cleaning and washing fan blades, fan body etc with soap solution after repairing re- assamble the same and transporting from workshop to any location in Palampur Mil Station and fixing to position / location as directed by Engineer-in- charge, connecting to electric system, testing etc complete all as specified and directed by Engineer-in-charge: - Note: -(i) Replacement of parts/rewinding shell be measured and paid separately (ii) Quoted rate is deemed to be inclusive of transporting fan from any location in Army Area to MES store & taking down unserviceable/ defective parts.(iii) Item such as bearings, bushes, capacitor, shaft etc required for replacement shall be measured and paid seperately as supply only.

Taking down and transporting of exhaust fan 8'' (200mm) /9" (230mm)/10'' (250mm )/ 12" (300mm) / 15" (375mm)/ 18" (450mm) sweep from any location inside Palampur Mil Stn to MES E/M Store Yard / Workshop for stripping of fan washing thoroughly of bearing / bush by petrol, washing / cleaning fan blade body etc thoroughly provision of new greasing replacement of worn-out / defective unserviceable parts (wherever necessary) assembling the same after defective / unserviceable parts is replaced including provision of twisted twin core flexible wire upto 0.7 mts long size 23/0.0076 (ISI marked) and re-fixing the same at the same location/other location including making good disturbed surface including testing to entire satisfaction of Engineer-in-charge. Note: -(i) Replacement of parts/rewinding shell be measured and paid separately (ii) Quoted rate is deemed to be inclusive of transporting fan from any location in Army Area to MES store & taking down unserviceable/ defective parts. (iii) Item such as bearings, bushes, capacitor, shaft etc required for replacemen shalled be measured and paid seperately as supply only.

Supply in replacement U clamp complete with nut bolt washer, split pin and rubber seal etc complete all as specified and directed by engineer in charge.

M&L cutting and taking out old burnout winding of any sweep ceiling fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of Engineer- in- charge.

M&L cutting and taking out old burnout winding of 250 mm sweep exhaust fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of engineer in charge.

M&L cutting and taking out old burnout winding of 300 mm sweep exhaust fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of engineer in charge.

M&L cutting and taking out old burnout winding of 450 mm sweep exhaust fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of engineer in charge.

Supply and fix in replacement condensor 1.5 MFD suitable for ceiling fan / exhaust fan / wall mounting fan of any sweep complete all as specified and directed by Engineer-in-charge.

S&F in replacement condensor 2.5 MFD suitable for ceiling fan / exhaust fan / wall mountaining fan of any sweep complete all as specified and directed by Engineer-in-charge.

S&F in replacement condensor 4 MFD suitable for ceiling fan / exhaust fan / wall mountaining fan of any sweep complete all as specified and directed by Engineer-in-charge.

S&F in replacement ball bearing suitable for ceiling fan / exhaust fan / wall mounting fan of any sweep complete all as specified and directed by Engineer-in-charge.

S&F in replacement gun metal bush suitable for ceiling fan / exhaust fan / wall mounting fan of any sweep complete all as specified and directed by Engineer-in-charge.

Supply and fix in repairs steped type, switch type, electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed by engineer in charge.

Material and labour spray painting of ceiling fan, fan blades, down rod, canopy etc with a coat of synthetic enamel paint of approved colour and quality including preparation of old painted surfaces, cleaning etc and printing the MES fan numbers etc with black paint complete all as directed by Engineer-in-charge.

Supply and fix motor of Exhaust Fan (plastic body) Capacity 200 mm as in repair including taking down of old unsv motor complete all as specified and directed by Eng-in - Charge .

Supply and fix motor of Exhaust Fan (plastic body) Capacity 250 mm as in repair including taking down of old unsv motor complete all as specified and directed by Eng-in - Charge .

Supply and fix in repair electronic meters temper proof LCD display with polycorbonate cover Single Phase 230 V ,10-60A accuracy class -1 50 Hz ,Conforming to IS 13779 ,IP-54, withh parameters to show data , time , Current reading ,load ,PF , voltage , & KWH all as specified and directed. Note: Old unserviceable Energy Meter to be deposited in MES store yard.

Supply and fix in repair electronic meters temper proof LCD display with polycorbonate cover Three Phase 415 V ,10-60A accuracy class -1 50 Hz ,Conforming to IS 13779 ,IP-54, withh parameters to show data , time , Current reading ,load ,PF , voltage , & KWH all as specified and directed. Note: Old unserviceable Energy Meter to be deposited in MES store yard.

S&F 1200 mm sweep ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. Note: Old unserviceable ceiling fan to be deposited in MES store yard.

S&F 250 mm sweep exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding, 5 star rated complete all as specified and directed. Note: Old unserviceable exhaust fan to be deposited in MES store yard.

S&F 250 mm sweep exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding, 5 star rated complete all as specified and directed. Note: Old unserviceable exhaust fan to be deposited in MES store yard.

S&F 300 mm sweep exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding, 5 star rated complete all as specified and directed. Note: Old unserviceable exhaust fan to be deposited in MES store yard.

S&F new wall mounted fan 400 mm sweep with oscillating arrangement, inbuilt speed control and ON-OFF switch arrangement complete all as specified and as directed. Note: Old unserviceable wall mount fan to be deposited in MES store yard.

S&F in replacement LED Driver 36watt, 230V, 50Hz, complete all as specified and directed by Engr-in-charge.

S&F in replacement LED Driver 18watt, 230V, 50Hz, complete all as specified and directed by Engr-in-charge.

M/S MALHI CONSTRUCTIONS (BID ID -3340093)

somyaenterprises (BID ID -3339988)