GENERAL-Renovation works to Vigilance and Anti Corruption Bureau- Providing cubicles in DYSP office,Second floor-2024-25

Amount

Cubicle works

OD277094/2024-2025:Engaging man mazdoor for cleaning and other works .

OD277091/2024-2025:Providing and fixing 18mm thick Marine plywood conforming to IS:710 in staff tab1e,she1ves, drawers with screws and adhesive wherever

OD277110/2024-2025:Providing and fixing 12mm thick Marine plywood conforming to IS:710 in partition,she1ves withscrews and adhesive whereverrequired.

OD277090/2024-2025:Providing and fixing 4mm thick Teak Veneer on plywood using synthetic adhesives ,neccessary screws ,Veneer to be provided only on visible surface,including all cost of materials all labour charges etc complete.

9.112:Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18x5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge.

OD277095/2024-2025:Providing and fixing stainless steel soft close cabinet hinges with stainless steel screws etc.

9.115:providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer -in-charge.

9.165.1:Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.165.2:Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.100mm

OD277097/2024-2025:Melamine polishing on wood work (two coat)

OD277093/2024-2025:Providing and fixing U shaped movable stainless steel grab bar of standard length and approved make as per direction of engineering in charge

OD68250/2025-2026:Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade: One or more coats on old work

OD68253/2025-2026:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Scrap shed

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

SUVIN M P (BID ID -2446837)

Bidder Name

prajithkalathil

SUVIN M P