Const.of Health Sub Centre building at Kot Plahari inTehsil Nurpur Distt. Kangra HP

Amount

Excavation in foundation, trenches etcetera in earth work in all classification of soil such as pick work, jumper work, pick jumper . jumper blasting , hard blasting in dry or saturated conditions unto any depth and lift including chiseling or any other mixed variety of soil including shoring, strutting and pumping out water where required including stacking the serviceable and unserviceable material clear from the edges of excavation as directed by the Engineer-in-charge and then returning the stacked soil in fifteen centimeters layers when required into plinths and sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus unserviceable excavated earth as directed within all leads and lifts disposed materials to be neatly dressed levelled as directed by the Engineer-in Charge including carriage of materials within all leads and lifts and other incidental charges .

Excavation in drains and channels etcetera in all kinds of classification of soil such as pick work, pick jumper work, blasting work , hard blasting or any other mixed classification of soil including chiseling and dressing of sides and bed and disposing of all excavated earth in all leads and lifts. Disposed earth to be levelled and neatly dressed as directed by the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental charges.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in foundation, footing, basis of column etc. and mass concrete including carriage of materials within all leads and lifts.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings , shelves and the like floor etc. upto any in all thickness including carriage of materials within all leads and lifts.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like etcetera including carriage of materials within all leads and lifts.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in columns, pillars, posts and struts ( square rectangular or polygonal in plan ) in any heights / thickness/depths etcetera including carriage of materials within all leads and lifts.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frames 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in stair cases with sloping or stepped soffits excluding landing including carriage of materials within all leads and lifts.

Providing form work with steel plates 3.15mm(three point one five millimeters) thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Beams, cantilevers, girders and lintels sides and soffits of beams, beam haunching, cantilevers, girders, bressumers and lintels in any heights / thickness/depths etcetera including carriage of materials within all leads and lifts.

Providing form work with steel plates 3.15mm(three point one five millimeters) thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in edges of slab and breaks in floors and walls of any width etcetera including carriage of materials within all leads and lifts.

Providing and laying cement concrete 1:4:8 (one cement; four sand : eight graded /crushed stone aggregate 40mm(forty millimeters) nominal size mixed and vibrated mechanically and curing complete excluding the cost of form work in foundation and plinth in all depths including carriage of materials within all leads and lifts and other incidental charges.

Providing and laying cement concrete 1:6:12 (one cement; six sand twelve graded /crushed stone aggregate 40mm(forty millimeters) nominal size mixed and vibrated mechanically and curing complete excluding the cost of form work in foundation and plinth in all depths including carriage of materials within all leads and lifts and other incidentals charges.

Providing and laying cement concrete 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (twenty millimeter) nominal size mixed and vibrated mechanically so as to give a compressive strength corresponding to grade M-20(M-twenty) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation , footings, basis of columns etc., and the like and mass concrete including carriage of materials within all leads and lifts other incidental charges .

Providing and laying cement concrete 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (twenty millimeter) nominal size mixed and vibrated mechanically so as to give a compressive strength corresponding to grade M-20(M-twenty) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in walls including attached buttresses, pillasters , plinth and their caps and basis and string courses etc. and the like up to all floor level including carriage of material within all leads and lifts other incidental charges .

Providing and laying cement concrete 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (twenty millimeter) nominal size mixed and vibrated mechanically so as to give a compressive strength corresponding to grade M-20(M-twenty) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landing and shelves and their supports balconies, beams, girders, bressumers and cantilevers in all depths/ thickness etc. up to all floor level including carriage of materials within all leads and lifts other incidental charges .

Providing and laying cement concrete 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (twenty millimeter) nominal size mixed and vibrated mechanically so as to give a compressive strength corresponding to grade M-20(M-twenty) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars, posts and struts in all depths / thickness up to all floor level including carriage of material within all leads and lifts other incidental charges .

Providing and laying cement concrete 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (twenty millimeter) nominal size mixed and vibrated mechanically so as to give a compressive strength corresponding to grade M-20(M-twenty) upto all floor level and curing complete excluding cost of form work and reinforcement for reinforced concrete work in stair cases ( except spiral stairs cases) excluding landing, but including preparing of top surfaces and finishing of nosing including carriage of material within all leads and lifts other incidental charges .

Providing and laying cement concrete 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (twenty millimeter) nominal size mixed and vibrated mechanically so as to give a compressive strength corresponding to grade M-20(M-twenty) up to all floor level and curing complete excluding cost of form work in foundation and plinth in all depths / thickness including carriage of material within all leads and lifts other incidental charges .

Providing and laying mild/ tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all heights including cost of binding wire and carriage of materials within all leads and lifts.

Providing smooth finishing to exposed surface of reinforced cement concrete or cement concrete work with cement mortar 1:3 (one cement three sand)complete in all floor/heights and curing complete including carriage of materials within all leads and lifts

Providing and laying cement concrete 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (twenty millimeter) nominal size ) mixed and vibrated mechanically so as to give a compressive strength corresponding to grade M-20(M-twenty) reinforced concrete chajja of any thickness up to floor two level including finishing the exposed surface with cement mortar 1:3 ( one cement : three sand ) to give a smooth and even surface including the centering / form work and curing complete excluding cost of reinforcement including carriage of materials within all leads and lifts and other incidental.

Brick masonry using second class common burnt clay building bricks in foundation and plinth in mud mortar including carriage of materials within all leads and lifts and other incidental.

Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:5(one cement: five sand) and curing complete including carriage of materials within all leads and lifts and other incidental.

Random rubble masonry polygonal rubble masonry ( uncoursed / brought to courses ) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 ( one cement: six sand : twelve graded stone aggregate 20mm nominal size ) a plinth level in cement mortar 1:6 ( one cement: six sand) and curing complete including carriage of materials within all leads and lifts and other incidental.

Providing and laying pre-cast cement concrete hollow block masonry with cement concrete block of size 40cm x 19 cm x 20 cm including quoin block jamb block and closers etc. made of cement concrete 1: 3:6 ( one cement: three sand : six graded stone aggregate 20mm nominal size )laid with cement mortar 1:6 ( one cement: six sand) in super structures up to all floor level and curing complete including carriage of materials within all leads and lifts and other incidental.

Providing and laying pre-cast cement concrete block masonry in partion wall 10 cm ( ten centimeters ) thick with solid block of approved size including quoin block jamb block and closers etc. made of cement concrete 1: 3:6 ( one cement: three sand : six graded stone aggregate 20mm nominal size ) a plinth level in cement mortar 1:6 ( one cement: six sand) and curing complete in super structures above plinth level to floor all level including carriage of materials within all leads and lifts and other incidental.

Boulder filling dry hand packed tightly under floor including dressing complete as directed by the Engineer-in Charge including carriage of materials within all leads and lifts and other incidental charges.

Filling in plinth with sand under floor including watering, ramming ,consolidating and dressing complete as directed by the Engineer-in Charge including carriage of materials within all leads and lifts and other incidental charges..

Providing and fixing factory made I.S.I. marked NO. IS 1003 flush door shutters interior grade commercial type core of block board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains or cross bands and face Veneers on both faces of shutters 40mm ( forty millimeters) thick including black enameled Mild steel, butt hinges including carriage of materials within all leads and lifts.

Providing and fixing 19mm(Nineteen millimeters) thick commercial board water proof shutters for cupboard etcetera including nickel plated bright finished piano hinges with necessary screws complete including 6mm ( six millimeters ) thick hard wood edging to be finished with mica top as per direction of Engineer-in-charge including carriage of materials in all leads and lift s.

Providing and fixing cabinet work made of 19mm(Nineteen millimeters) thick water and termite proof commercial board including vertical partitions, shelve and shutters frame of first class hard wood and hard wood edging lifting 6mm ( six millimeters ) thick complete including top finished with 1mm (one millimeter ) thick mica lamination sheet of approved shade and 6mm ( six millimeters ) thick commercial ply back side complete including nickle plated bright finished piano hinges and carriage of materials in all leads and lift s.

Providing and fixing 40mm(forty millimeters) thick second class deodar wood paneled glazed or paneled and glazed shutters for doors, windows and clerestory windows including bright finished black enamelled iron butt hinges with necessary screws including carriage of materials in all leads and lifts. .

Providing and fixing 40mm(forty millimeters) thick second class deodar wood wire gauges shutters using galvanized M.S.wire gauge of I.S.gauge designation 85-G ( eighty five-G )with wire of dia 0.56mm (zero point five six millimeters)for doors, windows, and clerestory windows including bright finished black enamelled iron butt hinges with necessary screws including carriage of material in all leads and lifts. .

Providing and fixing anodized aluminum sliding doors bolts,(anodized transparent or dyed to required colour and shade with bolts and nuts/screws etc. complete including carriage of materials with in all leads and lifts a) 300 x 16mm (three hundred into sixteen)millimeter.

b) 250 x 16mm (two hundred fifty into sixteen)millimeter.

Providing and fixing anodized aluminum tower bolts, (Barrel type)anodized transparent or dyed to required colour and shade with bolts and nuts/screws etc. complete including carriage of materials with in all leads and lifts a) 200 x 10mm (two hundred into ten millimeter.)

Providing and fixing anodized aluminum tower bolts, (Barrel type)anodized transparent or dyed to required colour and shade with bolts and nuts/screws etc. complete including carriage of materials with in all leads and lifts a) 100 x 10mm (two hundred into ten millimeter.)

Providing and fixing 65x35 mm ( sixty five into thirty five millimeters) special quality bright finish brass cup boards locks or ward robe locks with six levers including necessary screws complete including carriage of materials with in all leads and lifts

Providing and fixing 100mm ( one hundred millimeters ) bright finish brass floor door stopper with rubber cushion and including necessary screws to suit shutters thickness complete including carriage of materials with in all leads and lifts

Providing and fixing 150mm ( one hundred fifty millimeters ) oxidized Mild steel double acting spring hinges with necessary screws complete including carriage of materials with in all leads and lifts

Providing and fixing 200mm ( two hundred millimeters ) oxidized Mild steel hooks and eves with necessary screws complete including carriage of materials with in all leads and lifts

Providing and fixing oxidized Mild steel fan catch with necessary screws complete including carriage of materials with in all leads and lifts

Providing and fixing 8mm ( eight millimeters ) thick cement bonded particles boards ceiling of approved quality on angle iron /t-section frame with butt jointing and nails ( frame work and cover fillets to be measured and paid separately )

Providing and fixing 12mm( twelve millimeter )thick and 150mm(one hundred fifty millimeter )wide first class deodar wood pelmet with 25mm(twenty five millimeter) dia meter wooden curtain rods and brackets including fixing 25x3mm(twenty five into three millimeter) Mild Steel flat 10 cm (ten centimeter ) long and plugs etc. complete with necessary screws including carriage of material within all leads and lifts.

Providing and fixing Mild steel plain grills of required patterns in angle iron frame of windows etc. with Mild steel flat square or rounded bars with bolts and nuts or by screws and welding with frame complete including carriage of materials within all leads and lifts.

Providing and laying automatic hydraulically compressed and polished pre-cast terrazzo tiles ISI marked No. IS-1237 of approved shade, 20mm ( twenty millimeters ) thick with marble chips of specified size laid in floors, treads of steps, and landing on a bed of 25mm ( twenty five millimeters ) average thickness of cement mortar 1 :3 ( one cement : three sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles ( wherever required including rubbing and polishing complete) with tiles of medium shade including carriage of materials with in all lead and lifts.

Providing and laying automatic hydraulically compressed and polished pre-cast terrazzo tiles of ISI marked No. IS-1237 of approved shade, 20mm (twenty millimeters ) thick with marble chips of specified size laid in skirting, risers of steps and dado upto any height laid on 10mm ( ten millimeters ) average thickness of cement plaster 1:3 ( one cement: three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles ( wherever required ) including rubbing and polishing complete)with tiles of medium shade up to all floors level including carriage of materials in all leads and lifts and other incidental.

White glazed tiles 6mm (six millimeters) thick in skirting, risers of steps and dado for all heights on 12mm (twelve millimeter) thick cement mortar 1:3 ( one cement; three sand) and jointed with white cement slurry complete up to all floor level including carriage of materials within all leads and lifts and other incidental charges.

Providing and laying 40mm(forty millimeters) thick Cement concrete flooring 1:2:4 (one cement; two sand; four graded stone aggregate 20mm (twenty millimeters) nominal size ) laid in one layer finished with a floating coat of neat cement upto all floor level and curing complete including carriage of materials with in all leads and lifts.

Providing and laying 15mm ( fifteen millimeters ) thick Cement plaster skirting or dado upto any height with cement mortar 1:3(one cement; three sand ) finished with a floating coat of neat cement including rounding of junction with floors and curing complete upto all floor level including carriage of materials within all leads and lifts.

Providing and laying 20mm(twenty millimeter) thick white makrana marble work ( table rubbed and polished) in flooring laid over 20mm ( twenty millimeters ) thick base in cement mortar 1:3 ( one cement : Three sand ) including jointing with cement mortart 1:2 (one cement: two marble dust ) with an admixture of pigment to match the shade of marble including carriage of materials within all leads and lifts.

Providing and fixing 0.60mm (zero point six zero millimeters) thick preprinted steel sheet in roofing with hot dipped zinc coated sheet with top coat of regulated modified polyster ( R N P ) organic coating of 20( twenty ) micron over 5 ( five ) micron primer coating to back coat of polyster of 5 ( five ) micron over 5 ( five ) micron primer coating including fixing with prepainted iron J or L hooks , bolts and nuts 6mm dia meter with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in- charge including carriage of materials within all leads and lifts..

Providing and fixing ridges or hips 60 cm (sixty centimeters)over all with 0.60mm (zero point sixty millimeters) thick prepainted steet sheet in roofing with hopt dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 ( twenty ) micron over 5 ( five ) micron primer coating + (plus ) back coat of polyster of 5 ( five ) micron over 5 ( five ) micron primer coating including fixing with prepainted iron J or L hooks , bolts and nuts 6mm dia and prepainted G I limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in- charge including carriage of materials within all leads and lifts.

Providing and fixing valleys 60cm (ninety centimeters) over all 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polster organic coating of back coat of polyster of 5 ( five ) mircon over 5 ( five ) micron primer coating including fixing with prepainted iron J or L hooks , bolts and nuts 6mm dia with prepainted G I limpet and bitumen washer complete with all acessoris as required as per the directions of Engineer in charge including carriage of materials within all leads and lifts.

Providing and fixing 0.63mm ( zero point six three millimeters ) thick plain galvanized iron sheet 15cm ( fifteen centimeters ) wide 45 cm ( forty five centimeters ) deep overall semi circular plain galvanized iron sheet gutter with iron bracket 40x3mm ( forty into three millimeters ) size bolts and nuts and washer etc. complete including making necessary connection with rain water pipe complete as per drawing and design including carriage of materials within all leads and lifts.

Providing and fixing on wall faces polyvinyl chloride ( D-plast) rain water pipes of working pressure not less than 4.5 kg. (four point five kilogram )/ square meter including filling the joints with approved adhesive complete in all respect in all heights including carriage of materials in all lead and lifts and other incidental charges.

Providing and fixing on wall face polyvinyl chlorate ( D-plast) rain water pipe pressures not less than 4.5 kg. / sqm ( four point five kilogram ) per square meter including filling the joints with approved adhesive complete in all respect in all heights including carriage of materials in all lead and lifts and other incidental charges. a)PVC plain bend 150mm ( one hundred fifty millimeters )

Providing and fixing on wall face polyvinyl chlorate ( D-plast) rain water pipe pressures not less than 4.5 kg. / sqm ( four point five kilogram ) per square meter including filling the joints with approved adhesive complete in all respect in all heights including carriage of materials in all lead and lifts and other incidental charges. b) PVC shoe 100mm ( one hundred millimeters

Providing and fixing Mild steel black paint sheet 1.66mm to 2mm ( one point six six millimeters to two millimeters ) thick in eaves boards/ facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge ( Base members of steel work shall be measured and paid separately) including carriage of materials within all leads and lifts.

Steel work welded in built up sections composed of beams, joist, channels, angles ,Tee- flats, with connecting plates or angle cleats etcetera as in trusses, and trussed purlins main and cross-beams, hips and jack rafters , purlins connecting to common rafter and the like in building including cutting, fixing ,lifting , hoisting and placing in position complete and applying a priming coat of red lead paint including carriage of materials within all leads and lifts. a) In trusses and trussed purlins in buildings.

Steel work welded in built up sections composed of beams, joist, channels, angles ,Tee- flats, with connecting plates or angle cleats etcetera as in trusses, and trussed purlins main and cross-beams, hips and jack rafters , purlins connecting to common rafter and the like in building including cutting, fixing ,lifting , hoisting and placing in position complete and applying a priming coat of red lead paint including carriage of materials within all leads and lifts. b) In gratings, framed guards bars ladders, railing brackets and the like ceiling frames etc.

Providing and fixing mild steel round holding down or anchor bolts with nuts and washers plates complete including carriage of materials with in all leads and lifts.

Providing and fixing steel glazed doors, windows and clerestory windows and ventilators of standard rolled steel section joints mitered and welded with 16x3.15mm (sixteen into three point one five millimeters)lugs 10 cm.(ten centimeters) long embedded in cement concrete blocks 15x10x10cm( fifteen into ten into ten centimeters ) size of 1: 3 : 6 ( one cement: three sand: six crushed/ graded, broken stone aggregate 20mm (twenty millimeters nominal size ) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required and iron fittings such as handles , tower bolts ad nuts including providing and fixing of glass panes with glazing clips and special metal sash putty of approved make complete including applying a priming coat of red lead paint as per drawing and design or and as per directions of Engineer- in-charge and carriage of materials with in all leads and lifts (a) Fixed steel windows.

Ventilator top hung

Providing and fixing double steel shutters windows side hung ( one glazed and other wire gauged ) including frame of channel ISLC- 75 ( seventy five ) flapped with mild steel flat 75x4mm ( seventy five into four millimeters ) and 50x4mm ( fifty into four millimeters ) in the opening of sides of channels to make multiframe and shutters of rolling steel Z-section and T-section and T-hinges ,handles with closing device and making provision of other window fixing where required with 16x3.15mm ( (sixteen into three point fifteen millimeters) lugs 10 cm.(ten centimeters) Long embedded in cement concrete 1: 3 : 6 ( one cement: three sand: six crushed/ graded, broken stone aggregate 20mm (twenty millimeters ) nominal size ) or with wooden plug and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required sand iron fittings including providing and fixing glass pans with glazing clips and special metal sesh putty of approved make for glazed shutters and metal beading with screws etc. and including fixing of wire gauge using galvanized M.S. wire gauge of IS gauge designation of 85-G ( eighty five- G ) with wire of 0.56mm ( zero point five six millimeters ) and wire mesh with M. S. flat 20x3mm ( twenty into three millimeters ) for beeding and screws and applying priming coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer- in-charge and carriage of materials in all lead and lifts and other incidental. Side hung window ( one glazed and other wire gauged )

Providing and fixing angle iron frames for cup board manufactured from M.S .angle iron section 25x25x5mm (Twenty five into twenty five into five millimeters) thickness including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 25x25mm (Twenty five into twenty five millimeters) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two point five millimeters) thick with provision for locking arrangement and shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer-in-charges including carriage of materials in all leads and lifts

Providing and fixing M.S. fan clamp type-I of 16mm ( sixteen millimeters) dia Mild steel bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of loop all as per standard design complete including carriage of materials in all lead and lifts.

Providing and fixing angle iron doors, windows, clerestory windows framed manufactured from steel iron section 40x40x6mm ( forty into forty into six millimeters) thickness including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 25x25mm (Twenty five into twenty five millimeters) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two point five millimeters) thick with provision for locking arrangement and shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer-in-charges including carriage of materials in all leads and lifts..

Providing and fixing standard steel angle iron door frame double rebate manufactured from M.S. angle section of 40x40x6mm ( forty into forty into six millimeters ) and M.S. flat 50x6mm ( fifty into six millimeters ) and M.S. flat 25x 6 mm ( twenty five into six millimeters ) combined together to make one frame as per drawing and designs including hinges, jamb, lock jamb, beed and if required angle thrashold of M.S. angle 50x25mm ( fifty into twenty five millimeters ) welded or rigidly fixed by mechanically means lugs with split end tails to each jamb including steel butt hinges 2.5mm ( two point five millimeters ) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved / steel primer after pretreatment of the surface as directed by Engineer-in- charge complete including carriage of materials within all leads and lifts

Providing and fixing railing for stair case having baluster 19x19mm ( nineteen into nineteen millimeters ) solid square bars with a clear height of 85cm ( eight five centimeters ) and 60cm ( sixty centimeters )center to center jointing in steps and welded with electric gas at top along with hand rail of hollow Mild steel rectangular pipe 60x40mm(sixty into forty millimeters ) ( ISG-16) vertical baluster welded or jointed with each other with two row of Mild steel flat 50x5mm ( fifty into five millimeters ) including applying a priming coat with steel primer and painting two or more coats with steel enamel paint other than white including carriage of materials within all leads and lifts.

Applying priming coat over new steel and other steel metal based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes , fine steel wood scrappers and sand papering complete with ready mixed priming paint brushing red lead, oxide / zinc oxide chrome including carriage of materials with in all leads and lifts.

Painting two or more coats(excluding priming coat ) on new steel and other metal surfaces under coat with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust, and other foreign matter, with enamel paint other than white including carriage of materials with in all leads and lifts.

Applying priming coat over new wood and wood based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting with ready mixed paint brushing wood primer pink including carriage of materials with in all leads and lifts

Painting two or more coats(excluding priming coat ) on wood and wood based surfaces with ready mixed paint of approved brand and manufacture of approved shade brushing to give an even shade including cleaning the surfaces of all dirt, dust, and other foreign matter, complete with ready mixed paint other than white including carriage of materials with in all leads and lifts.

Applying priming coat over new concrete / masonry/ asbestos cement / plastered surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matter complete and sand papering as required with ready mixed primer including carriage of materials with in all leads and lifts.

Applying Birla whitewall care putty over plastered surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matter sand papered smooth to give final finish to the surfaces complete including carriage of materials with in all leads and lifts.

Wall painting ( two or more coat ) with acrylic emulsion paint of approved brand and manufacture of approved shade for interior grade on undecorated concrete / stone / plastered wall surfaces to give an even shade including thoroughly brushing the surfaces free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for making the surfaces complete including carriage of materials with in all leads and lifts.

6mm (six millimeter)thick cement plaster to ceiling with cement mortar 1:3(one cement; three sand) upto all floor level and curing complete including carriage of materials in all lead and lifts upto floor level two level.

15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6(one cement; six sand) in single coat on rough side of brick/concrete/stone walls for interior plastering in heights / floor level including arises, internal rounded angles, chamfers and/ or rounded angles in all girth and finished even and smooth including carriage of materials with in all leads and lifts and other incidental charges.

15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6(one cement; six sand) in single coat on fair side of brick/concrete/stone walls for interior plastering in all heights floor level including arises, internal rounded angles chamfers and/ or rounded angles in all girth and finished even and smooth including carriage of materials with in all leads and lifts and other incidental charges.

15mm (fifteen millimeters) thick cement plaster with cement mortar 1:3(one cement; three sand) in single coat on fair side of brick/concrete/stone walls for interior plastering in all heights / floor level including arises, internal rounded angles chamfers and/ or rounded angles in all girth and finished even and smooth including carriage of materials with in all leads and lifts and other incidental charges.

White washing with lime on undecorated ceiling and / or sloping roofs ( two or more coats ) to give an even shade including thoroughly brooming the surface to remove all dirt, dust mortar drops and other foreign matter including carriage of materials with in all leads and lifts and other incidental charges.

White washing with lime on undecorated wall surfaces (two or more coats) to give an even shade including thoroughly brooming the surface to remove all dirt, dust, mortar drops and other foreign matter including papering the surface even and sand papered smooth and carriage of materials within all leads and lifts.

Distempering(two or more coats) with oil bound washer distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surfaces even and sand papered smooth including carriage of materials with in all lead and lifts.

Finishing wall with water proofing cement paint of approved brand and manufacture of required shade on undecorated wall surfaces ( two or more coats ) to give an even shade after thoroughly brushing the surface to remove all dirt, dust and remains of loose powdered materials upto all floor level including carriage of material within all leads and lifts.

Providing under layer for plinth protection of 75mm (seventy five millimeters) thick (unconsolidated) bed of dry brick/stone aggregate 40mm( forty millimeters) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground complete and carriage of materials with in all leads and lifts and other incidental charges.

Providing plinth protection 50mm( fifty millimeters) thick cement concrete 1:3:6 ( one cement; three sand; six graded stone aggregate 20mm(twenty millimeters) nominal size)and curing complete including finishing the top surface of concrete smooth and carriage of materials within all leads and lifts

Constructing 15x22 cm(fifteen into twenty two centimeter) U-shape open surface drains with square rubble stone masonry wall in cement mortar 1:6 ( one cement; six sand ) and inside plastering with cement plaster 1:3 (one cement; three sand) including earth work and laying 10 centimeter (Ten centimeters) cement concrete in 1:5:10(one cement; five sand; ten graded stone aggregate 40mm (forty millimeter nominal size) and 75cm(seventy five centimeter) cement concrete 1:2:4 (one cement, two sand; four graded stone aggregate 20mm (Twenty millimeter) nominal size at bottom joint of drain and finished with a floating coat of neat cement complete as per standard design including carriage of materials in all leads and lifts.

Providing and filling in bricks bats / stone aggregate in soak pit complete including carriage of materials in all leads and lifts.

Providing and laying in trenches ISI marked 20mm( twenty millimeters) nominal bore galvanized mild steel tubes ( medium grade ) tube fittings (Earth work in trenches to be measured and paid for separately) including carriage of materials with in all leads and lifts of materials.

Providing and fixing to wall ceiling and floor ISI marked galvanized mild steel tubes (medium grade) tube fittings and clamps including making good the wall, ceiling and floor in all heights / floors including carriage of materials within all leads and lifts. I) 20mm ( twenty millimeters) nominal bore.

Providing and fixing to wall ceiling and floor ISI marked galvanized mild steel tubes (medium grade) tube fittings and clamps including making good the wall, ceiling and floor in all heights / floors including carriage of materials within all leads and lifts. I) 15mm( fifteen millimeters) nominal bore.

Providing and laying in trenches ISI marked centrifugally cast (spun ) iron sockets spigot pipe class-A ( Earth work in trenches and jointing of pipe to be measured and paid separately ) complete including carriage of materials within all leads and lifts a) 100mm (one hundred millimeters) nominal diameter.

Providing and laying double socket C.I. bends ( medium class) complete including carriage of material within all leads and lifts and other incidentals. a) 100mm ( one hundred millimeter) nominal dia meter 90(ninety) degree

Providing and laying all sockets C.I. tees (medium class) complete including carriage of material within all leads and lifts. i) 100mmx 100mm.( One hundred millimeters into One hundred millimeters)nominal diameter

Providing and fixing sand cast / cast iron spun spigot and socket soil waste and ventilating pipe ( lead caulked joints to be measured and paid for separately ) complete including carriage of materials within all leads and lifts a) 75mm. ( seventy five millimeters)nominal diameter

Providing and fixing sand cast / cast iron spun spigot and socket soil waste and ventilating pipe ( lead caulked joints to be measured and paid for separately ) complete including carriage of materials within all leads and lifts a) 100mm. ( One hundred millimeters)nominal diameter

Providing and fixing cast iron holder bats including steel bolts to sand cast iron / cast (spun ) iron pipes embedded in and including cement concrete block 100 mm x 100 mm x 100mm ( one hundred millimeters into one hundred millimeters into one hundred millimeters ) of 1:2:4 ( one cement : 2 sand: 4 graded stone aggregate 20mm ( twenty millimeters ) nominal size ) mix including cast of ceiling holes and making good the wall complete as directed by the Engineer-in- charge including carriage of materials within all leads and lifts a) 75mm. ( seven ty five millimeters)nominal diameter size pipe.

Providing and fixing cast iron holder bats including steel bolts to sand cast iron / cast (spun ) iron pipes embedded in and including cement concrete block 100 mm x 100 mm x 100mm ( one hundred millimeters into one hundred millimeters into one hundred millimeters ) of 1:2:4 ( one cement : 2 sand: 4 graded stone aggregate 20mm ( twenty millimeters ) nominal size ) mix including cast of ceiling holes and making good the wall complete as directed by the Engineer-in- charge including carriage of materials within all leads and lifts b) 100mm (one hundred millimeters) nominal diameter. Size pipe.

Providing and fixing and cast iron/cast iron spun fittings and accessories bends of required degree(any radius) (a) with oval access door insertion rubber washer 2mm ( two millimeters) thick bolts and nuts complete including carriage of materials within all leads and lifts 75mm( seventy five millimeter ) nominal size dia meters.

Providing and fixing sand cast iron/cast iron spun fittings and accessories bends of required degree(any radius) including carriage of materials within all leads and lifts Plain bend 75mm( seventy five millimeter ) nominal size.

Providing and fixing sand cast iron/cast iron spun fittings and accessories bends of required degree(any radius) complete including carriage of materials within all leads and lifts :Plain bend :100mm( one hundred millimeter ) nominal size.

Providing and fixing 100mm ( one hundred milimeters ) dia meter cast iron cowl complete including carriage of materials within all leads and lifts and other incidental.

Providing and fixing Mild steel stay and clamps for sand cast iron / cast (spun )iron pipes complete including carriage of materials within all leads and lifts.. 100mm ( one hundred millimeters ) nominal size diameter.

Providing and fixing cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating without vent arm complete including cost of cutting hole and making good the wall and floors etcetera including carriage of materials with in all leads and lifts:- 75mm ( seventy five millimeter) nominal size diameter

Providing and fixing Orissa pattern vitreous china water closet squatting pan ( Indian type water closet pan) size 580mm(five hundred eighty millimeters)(earth work, bed concrete foot rest and trap to be measured and paid for separately) including carriage of materials within all leads and lifts and other incidental.

Providing and fixing 100mm(one hundred millimeters) size sand cast iron P or S trap for water closet (squatting pan) including jointing the trap with pan and soil pipe in cement mortar 1:1( one cement: one sand) complete including carriage of materials within all leads and lifts and other incidental.

Providing and fixing 10/12.50/15.00 (ten / twelve point five / fifteen ) liters capacity PVC(polyvinyl Chloride) low level flushing cistern with a pair of cast iron or mild steel brackets complete with fitting such as lead valve, less syphen 15mm (fifteen millimeters) nominal size brass ball valve with polythene float chromium plated brass handle, unions and couplings for connections with inlet, outlet and overflow pipe 40mm (forty millimeters) dia. chromium plated flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet ( over flow pipe to be measured and paid for separately ) including carriage of materials within all leads and lifts and other incidental charges.

Providing and fixing flat back 630x450mm( six hundred thirty into four hundred fifty millimeters) nominal size vitreous china wash basin with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fitting complete including carriage of materials within all leads and lifts and other incidental

Providing and fixing stainless steel wash basin 550x 400mm dia ( five hundred fifty into four hundred millimeter ) dia meter diamond and model coda No. WB-2116 complete with C.I or M.S. brackets painted white cutting holes, and making good the same and including carriage of materials within all leads and lifts and other incidental

Providing and fixing 650x450mm(Six hundred fifty into four hundred fifty millimeters) size dia mond model coda No. WB-2116 stainless steel kitchen sink with cast iron or mild steel brackets painted white including cutting holes in walls and making good the same but excluding fitting complete including carriage of materials with in all leads and lifts..

Providing and fixing 32mm (thirty two millimeters) diameter lead waste pipe for wash basin or sink complete with brass check nut including carriage of materials within all leads and lifts and other incidentals.

Providing and fixing cast iron grating for gully , floor or Nahni trap complete including carriage of materials with in all leads and lifts ..

Providing and fixing 600mm x 450mm (six hundred millimeters into four hundred fifty millimeters) be velled edge mirror of superior glass mounted on 6mm ( six millimeters) thick asbestos cement sheet or ply wood sheet and fixed to wooden plugs with chromium plated Brass screws and washers complete including carriage of materials within all leads and lifts and other incidental.

Providing and fixing 600x20mm.(six hundred into twenty millimeter) chromium plated brass towel rail complete with chromium plated brass brackets fixed to wooden plugs with chromium plated brass screws including carriage of materials within all leads and lifts and other incidental..

Providing and fixing chromium plated brass soap dish with chromium plated brass brackets fixed to wooden cleats with chromium plated brass screws complete including carriage of materials within all leads and lifts and other incidental.

Providing and fixing chromium plated brass bath shower rose 150mm dia ( one hundred fifty millimeter dia meter ) with 15mm ( fifteen millimeters ) or 20mm ( twenty millimeters ) inlet complete including carriage of materials within all leads and lifts and other incidental.

Providing and fixing 15mm (fifteen millimeters )diamete chromium plated brass bib tap with capstan head complete including carriage of materials within all leads and lifts and other incidental.

Providing and fixing15mm (fifteen millimeter)diameters chromium plated brass pillar tap with capstan head complete including carriage of materials with in all leads and lifts and other incidental.

Providing and fixing 15mm (fifteen millimeters) diameter brass stop cock with necessary fitting including carriage of materials within all leads and lifts.

Providing and fixing P.V.C. Connection pipe with brass unions 45cm (forty five centimeters) long and 15mm (fifteen millimeters) nominal bore including carriage of materials within all leads and lifts.

Providing and placing 500( five hundred ) liter capacity each P.V.C.(poly vinyl chloride) water storage tank cylindrical shape ( ISI marked / Treepal layer ) universal or equivalent make ) including providing and fixing 25mm (twenty five millimeters) nominal bore galvanized mild steel tube over flow pipes, inlet and out let with fitting of suitable size along with ball valve and floating valve and P.V.C.( poly vinyl chloride) cover with locking arrangement including providing suitable base pad and hoisting in all heights including carriage of materials within all leads and lifts

Providing lead caulked joints to sand cast/ cast iron spun pipe sand fitting including testing of joints complete and carriage of materials with in all leads and lifts :- a) 75mm dia ( seventy millimeter) nominal diameter.

Providing lead caulked joints to sand cast/ cast iron spun pipe sand fitting including testing of joints complete and carriage of materials with in all leads and lifts :- 100mm ( one hundred millimeter) nominal diameter.

Constructing manhole with reinforced cement concrete top slab in cement concrete 1:2:4 ( one cement; two sand; four graded / crushed stone aggregate 20mm ( twenty millimeters ) nominal size), foundation concrete 1:4:8 ( one cement : four sand: eight graded / crushed stone aggregate 40mm(forty millimeters) nominal size) in side plastering 15mm ( fifteen millimeters) thick with cement mortar 1:3 (one cement; three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 ( one cement ; two sand; four graded / crushed stone aggregate 20mm ( twenty millimeters ) nominal size) finished smooth complete including curing and testing a) inside size 800mmx800mm (eight hundred millimeters into eight hundred millimeters) and any depth including cast iron cover with frame (light duty single seal pattern-I ) 455 x 610mm( four hundred fifty five into six hundred ten millimeters) internal dimension total weight of cover and frame to be not less than 38 kg. ( thirty eight kilogramme ) (Weight of cover 23 kg. (twenty three kilogramme) and weight of frame 15 kg.)(fifteen kilogramme) with 300mm (three hundred millimeters ) thick walls of square rubble masonry coursed with hard stone of approved quality in cement mortar 1:3(one cement; three sand) complete including carriage of material within all leads and lifts and other incidentals

Bhiwani Singh

VIVEK MAHAJAN

amisha gupta

ABHINAV MAHAJAN

ANKIT MAHAJAN