Budgeted work

Name Of Work :- A & A to Street Light on State Highway & Major District Road (MDR) of Devbhoomi Dwarka

Qty. Unit Description of Item Net Rate Per Amount

1 145.00 Mtrs Providing and erecting ISI mark Medium class RIGID PVC 24.24 Mtr.

. PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed (a)20 mm

2 145.00 Mtrs providing and erecting Mains with ISI marked, 1.5kV grade 70.70 Mtr.

. electrolyte multi stranded, annealed copper conductor

with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically

for control panel, relays, power switchgears, motor starters

& control wiring) with required size of copper lugs, nuts

and bolts if required. (e) One wire 6.00 sq. mm

3 2928.00 Mtrs Supplying and erecting Flexible PVC insulated multi strand 58.58 Mtr.

. multi core 1.1 kV grade ISI marked copper wires of

following size to be erected as directed. (e) 1.50 Sq.mm

core round PVC sheathed

4 366.00 Nos. Supplying and erecting LED street light / Flood light fittings 6695.29 Ea.

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate

optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Street Light (IP-

65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (v) 120 -

159 watts Cat. III

Qty. Unit Description of Item Net Rate Per Amount

5 7.00 Nos. Providing and erecting Approved make Four pole moulded 7469.25 Ea.

case circuit breaker having breaking capacity ICU of 25 KA.

at 415 V,having normal current rating up to 25 A to 100A.

with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 Hz. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III [Note:-1 Add Rs.

10% extra for housing/Encloser of MCCB for Item No 3-4-1

to 3-4-12 (The Enclosures should be used of same company

of MCCBs to be used)]

6 7.00 Rn. Providing and erecting busbar chamber confirming to IS- 4421.78 Rn.Mtr

Mtrs 375 fabricated from 16 G.M.S. sheet, dust & vermin proof

. having hinged door with rubber gasket and necessary

busbar supports with COPPER busbar having current

density not more than 1.6 Amp. / sq.mm (Rated current /

cross section area) duly wrapped with colour insulation

tape for phase sequence, three phase & neutral each

suitable for following current capacity with necessary

painting mounted on wall or pedestal frame of required

size with necessary connections. (A) Suitable for 63/100

7 366.00 Nos. providing and erecting Miniature circuit breaker single pole 297.95 Ea.

0.5A to 2A system and having breaking capacity 10 KA to

be erected in existing box. confirming to IS 8828/1996 with

ISI Mark Cat. III

8 22.00 Nos. Providing and erecting Sheet Steel powder coated MCB 355.52 Ea.

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing (a) single

door (IP-30) (i)4 way

9 22.00 Nos. Providing and erecting Approved make RCCBs conforming 3344.11 Ea.

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on 3 phase and neutral 415V,50Hz. having

characteristic of quick action & tripping with all advance

feature & do not incorporate any electronic component for

following Max. rating erected as directed. (iii) 63 Amps. FP

Qty. Unit Description of Item Net Rate Per Amount

10 14.50 Kgs Providing and erecting Annealed bare Copper wire 794.87 Kg.

11 29.00 Nos. Supplying & erecting earth pit of minimum bore 4591.46 Ea.

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with

high charge dissipation suitable for following type of

applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate

including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to

ensure the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B) Inner

chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to

retain moisture for long time Necessary test report must

be submitted by Agency. (a) For Electrical Installation up to

440V in normal soil Length of pipe - 1 Mtr Back filling

compound - 1 Nos Bag of 15 Kg.

12 15656.00 Mtrs Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI 168.67 Mtr.

. armoured cable multistrand / Solid Aluminium conductor

for 1.1 kV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (C) 4 core

13 3690.00 Mtrs Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI 184.83 Mtr.

. armoured cable multistrand Aluminium conductor for

kV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables (A) 4 core 16 Sq.

14 9397.00 Mtrs Making trench in soft soil of suitable width of 90 cm deep 55.55 Mtr.

. for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

15 4700.00 Mtrs Making trench in Hard Murrum / Tar Road of suitable 74.74 Mtr.

. width of 90 cm or required depth for laying any size of

cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

16 787.00 Mtrs Making trench in Hard Murrum / Tar Road of suitable 357.54 Mtr.

. width of 90 cm or required depth for laying any size of

cable or locating the fault all over the run and back filling

the same and making the surface as normal ground. (B) If

additional machinery like hammer driller or JCB use [Add]

Qty. Unit Description of Item Net Rate Per Amount

17 225.00 Mtrs Drilling the road without breaking the road surface 616.10 Mtr.

. (Asphalt) for laying of cable for feeding power supply by

making up to following size of holes at both ends complete.

(B) Up to 150 mm bore dia

18 206.00 Mtrs Providing & laying. R.C.C. Hume pipe for cable to be laid 90 226.24 Mtr.

. cm. below ground across the road crossing or on floor with

necessary material in an approved manner and making the

ground as per original. (F) 100 mm dia.

19 18962.00 Mtrs Providing & laying approved make Double walled 62.62 Mtr.

. corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable

(A)50 mm outer dia

20 22.00 Nos. Providing and, fixing heavy duty flange type brass cable 38.38 Ea.

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (C) 2 to 4 core 10 Sq. mm

21 51.00 Nos. Providing and, fixing heavy duty flange type brass cable 47.47 Ea.

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (D) 2 to 4 core 16 Sq. mm

22 88.00 Nos. Solder less crimping type Aluminium lugs conforming to IS 13.13 Ea.

suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (B) 10 Sq.mm

23 204.00 Nos. Solder less crimping type Aluminium lugs conforming to IS 15.15 Ea.

suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (C) 16/25 Sq.mm.

Qty. Unit Description of Item Net Rate Per Amount

24 198.00 Nos. Supply of approved make FRP Pole having following 18565.82 Ea.

specifications: FRP Light Pole made by CNC filament

winding machine using thermoset resin polyester/epoxy

resin system) having minimum 62% glass content. The pole

should be in one piece and tapered round in shape, having

smooth finish and should be totally free from corrosion as

well as non conductive & shock proof Pole should be

provided with FRP Anchor Base and it should be heavy

duty, or MS Material duly painted with Epoxy paint. Pole

should be flame retardant as per IS 6746. Resin used shall

be UV resistance and pigmented. A highly weather

resistant polyurethane coating shall be applied to the pole

after applying suitable primer system that ensures proper

adhesion of the paint. Minimum coating thickness shall be

80 to 100 micron. Deflection of the pole shall not exceed

more than 10% of the length of pole for the given load“

Pole should be generally made as per the dimensional

data, performance criteria and some interchangeability

features of poles as per standard ANSI C 136.20 latest

version or ASTM D 4923/01 including cable termination

box with necessary accessories .

The size of pole and type of installation with foundation as

per manufacturer details and site requirement are as

below . (1) Suitable for base plate mounting single arm

Bracket. [J] Overall length of 7 Mtr.Average Thickness:

7.5mm. Top/ Bottom OD Dia A/F 89/183 mm ± 2mm

approx. approx. Weight of Pole 40 kg approx. (Without

Base) Anchor Base (Size 300X300 & 18mm th.)

Qty. Unit Description of Item Net Rate Per Amount

25 84.00 Nos. Supply of approved make FRP Pole having following 19195.05 Ea.

specifications: FRP Light Pole made by CNC filament

winding machine using thermoset resin polyester/epoxy

resin system) having minimum 62% glass content. The pole

should be in one piece and tapered round in shape, having

smooth finish and should be totally free from corrosion as

well as non conductive & shock proof Pole should be

provided with FRP Anchor Base and it should be heavy

duty, or MS Material duly painted with Epoxy paint. Pole

should be flame retardant as per IS 6746. Resin used shall

be UV resistance and pigmented. A highly weather

resistant polyurethane coating shall be applied to the pole

after applying suitable primer system that ensures proper

adhesion of the paint. Minimum coating thickness shall be

80 to 100 micron. Deflection of the pole shall not exceed

more than 10% of the length of pole for the given load“

Pole should be generally made as per the dimensional

data, performance criteria and some interchangeability

features of poles as per standard ANSI C 136.20 latest

version or ASTM D 4923/01 including cable termination

box with necessary accessories .

The size of pole and type of installation with foundation as

per manufacturer details and site requirement are as

below . (2) Suitable for base plate mounting Double arm

Bracket. [E] Overall length of 7 Mtr. Average Thickness:

8mm. Top/ Bottom OD Dia A/F 114/183 mm ± 2mm

approx. approx. Weight of Pole 47 kg approx. (Without

Base) Anchor Base (Size 300X300 & 18mm th.)

26 198.00 Nos. Providing FRP arm bracket of having 2 sets of suitable 2934.05 Ea.

SS304 hardware for fixing the brackets & spread of

Mtr(Suitable for 89 to 114 mm pole top dia) (A) Single arm

27 84.00 Nos. Providing FRP arm bracket of having 2 sets of suitable 4524.80 Ea.

SS304 hardware for fixing the brackets & spread of

Mtr(Suitable for 89 to 114 mm pole top dia) (B) Double arm

Qty. Unit Description of Item Net Rate Per Amount

7.00 Nos. Supplying & erecting IP 55 grade following size section 16691.26 Ea.

pillar fabricated from joint less M.S. Sheet with angle iron

legs made from jointless M.S. Angle with cable clamps to

be buried in ground to have appropriate erection to work

uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side, with

internal and outside looking arrangement with lock and

keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos.

one is welded and other with nut and bolt for erecting

Bakelite sheet. Painting the Section Pillar inside and out

side with three tank powder coated paint. section pillar

roof should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of 1962 (A)

150 X 90 X 75 cm section pillar fabricated from 14 Gauge

MS Sheet with angle iron legs 95 cm long made from 40 X

40 X 6 mm thick MS angle.

29 7.00 Sq.M Supplying and erecting HYLAM sheet on existing angle iron 1541.26 Sq.

trs. frame.for following thickness (D) 8mm Mtr.

30 22.00 Nos. Supplying & erecting approved make IP 55 grade Company 17059.91 Ea.

fabricated Timer Panel of following capacity for switch On-

Off street lights on time scheduling basis made from 16G

CRCA sheet duly epoxy power painted inside and outside

with hinged doors and locking arrangement consisting of

suitable size of 4 Pole MCB and 4 pole contactor (cat-

III)with analog time switch, auto manual switch of same

make and suitable input and output Bakelite terminals

and with door earthing approved by Engineer in charge. (C)

Net Amount Put toTender Rs.

Note : This Estimate has been prepared as per new SOR which is exclusive of GST hence additional GST will be

paid to the agency as per existing guidlines.

Deputy Executive Engineer Executive Engineer

Electrical (R&B) Sub Division Electrical (R&B) Division

Jamnagar Rajkot