PROVN OF CERTAIN SANCTIONED WORKS AT NORTH OF RAILWAY LINE UNDER GE MISAMARI

Amount

Surface dressing not exceeding 15cm deep in soft/loose soil, complete all as specified as directed.

Excavation over area n exc 1.5 m deep and getting out in soft/loose soil, complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 metre wide for foundation etc or for shafts, wells cesspits, manholes etc not exceeding 10 Sqm on plan and not exceeding 1.5 metre in depth and getting out in soft / loose soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point in soil, complete all as specified and directed.

Removing excavated material exc. 1.50 km but n exc 5 Km and depositing where directed at a level n exc. 1.5 m above the starting point in soil, complete all as specified and directed.

M&L Cement concrete (1:4:8) type D2 ( using 40 mm graded stone aggregate) as in foundations, filling and mass concrete,complete all as specified and directed.

M&L Cement concrete (1:2:4) type B2 ( using 40 mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection , finishing cement concrete surfaces even & smooth without using extra cement, complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in sub base, complete all as specified and as directed.

M&L for 100mm thick PCC (1:2:4) type B2 (using 40 mm graded stone aggregate) as in sub base, complete all as specified and as directed.

M&L for 150mm thick PCC (1:2:4) type B2 (using 40 mm graded stone aggregate) as in sub base, complete all as specified and as directed.

M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggreagte) as in coping, bed block etc, complete all as specified and directed

M&L for PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in hold fast complete all as specified and directed

M&L for Reinforced Cement Concrete M-25 ( using 20mm graded stone aggregate) in Foundations including Rafts, Footings, Foundation Beams; Plinth Beams; bases for Columns, etc. Basement Slabs, Under-reamed Piles and Mass Concrete, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Items.

M&L for Reinforced Cement Concrete M-25 ( using 20mm graded stone aggregate) in columns, pillars, piers, post and strut, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Items.

M&L for Reinforced Cement Concrete M-25 ( using 20mm graded stone aggregate) as in beams, cantilevers, Chajjas, bressummers, lintels, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Items.

M&L Pre-cast Reinforced Cement Concrete (1:2:4) type B1 ( using 20mm graded aggregate) providing, in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), cover slabs ( for manhole and drains) string courses, copings, kneelers, apex stones, pier caps, columns, posts,boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar 1:4 complete with joints to match complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks (1:3:6) type C-1, (using 20mm graded stone aggregate) set in cement mortar 1:4, exc 10cm in width, complete all as specified and directed.

M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, complete all as specified and as directed.

M&L for TMT Bars 5mm dia and over upto and including 10mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, complete all as specified and as directed.

Use waste of formwork to sides of Concrete Foundations, Footings, bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of foundation and plinth beams and similar work; Square, rectangular or polygonal, vertical or to batter, flat, rough finished surfaces of concrete, complete all as specified and as directed.

Use waste of formwork to sides of Pillars, Posts, Struts, Piers, Columns and stanchions, flat, rough finished surfaces of concrete, complete all as specified and as directed.

Use waste of formwork to sides & soffits of floor or roof beams lintels & similar works., complete all as specified and as directed.

M&L for burnt brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 all as specified and directed.

M&L brick work with sub class'B' bricks, straight or curved on plan exc 6m radius in half brick wall built in CM 1:4 complete all as directed.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) mixed with water profing compound complete all as directed. Note : Water profing compound shall be measured and paid separately under relevant item.

M&L for rendering 15mm thick in Cement Mortar 1:6 on other than fair faces of brick or concrete Surfaces , plastered surfaces finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for 20mm thick plaster on fair faces of brick work or concrete surface in cm (1:4) with wpc @2% by weight face of conc work to wall surface and the surface is finished even and smooth without using extra cement, complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately under relevant item.

M&L for 15mm thick rendering on fair faces of brick work or concrete surface in cm (1:4) with wpc @2% by weight face of concrete work to wall surface and the surface is finished even and smooth without using extra cement, complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately under relevant item.

Supply only integral water proofing compound

M&L for sand filling under floors/trenches for cable protection, spreading, levelling, warering and well rammed in layers n.exc 25 cm thick, complete all as specified and as directed.

M&L for Hardcore of broken stone or boulders of gauge exc. 63mm but not exc.100mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and rammed to a true Surface, complete all as specified and as directed.

M&L for 20 mm thick screed bed or bedding layer of cement mortar (1:4) for laying floor finishes,complete all as specified and as directed.

M&L for cement concrete prepolished chequered 30 cm x 30 cm & 25 mm thick set and jointed & pointed in neat cement slurry with grey cement and pigment in floors complete all as specified & directed.

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigment, complete all as specified and directed.

M&L for Non skid ceramic coloured jointless tiles 7 to 8mm thick (Square/ Rectangular) area of each tiles exceeding 0.11 Sqm but n.exc. 0.18 Sqm in floors etc. over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles complete all as specified and as directed.

M&L for glazed ceramic coloured tiles, glossy finished of size 350x450x7mm thick as in vertical surfaces such as skirting/dados and riser of stems, over and including including 10 mm thick rendering/backing coat in CM 1:4 and set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles, complete all as specified and as directed.

M&L Heavy duty (Dura stone) Coloured Ceramic Tiles 300x300x8-10mm thick, in Floors, set and jointed in Neat Cement Slurry and pointed in White Cement mixed with Pigment to match the colour of tiles over and including 15 mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

S&F facroty made Second class hard wood kiln seasoned and chemically pressure treated plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

S&F powder coated aluminium anodised frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc, complete all as specified and as directed.

S&F powder coated aluminium anodised window/ventilator shutter side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised powder coated aluminium snap beading screws,75 mm long aluminium butt hinges-03 Nos on each shutter, hold fast complete all as specified and as directed. Note :- (i) Fixing of shutter with all powder coated fittings shall be as per manufactures instruction. (ii) Rate quoted is deemed to be inclusive of aluminium hardware as indicated, glazing clips, rubber packing, hinges, anodised aluminium snap on beading for fixing glass panes in frame, handles, locking arrangement but glass panes in frame shall be measured and paid separately at supply only rates.

S&F anodised aluminium grill ( anodised trasparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC15 of approved design/pattern with approved standared section and fixed to the exising windows frame with CP brass/ stainless steel screws @ 200 mm centre to centre all complete as per requirments, complete all as specified and as directed.

S&F powder coated anodised aluminium door shutters aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips rubber neoprene packing anodised aluminium snap beading screws etc complete all as specified and as directed.

S&F for anodised Aluminium sliding window and ventiletor frame made up 62 mm x29.5 mm x1.5 mm thick aluminium section & shutter made up 38 mmx 20 mmx1.5 mm thick without sash bar alum section including all necessary joining cleats,hold fast ,rubber gasket anodised snap beading,anodised aluminium fittings,suitable aluminium handle and locking arrangment etc complete all as specified and as directed.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with aluminium beads in squares not exceeding 0.5 Sq. M in each pane, complete all as specified and as directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with aluminium beads in squares not exceeding 0.5 Sq. M in each pane, complete all as specified and as directed.

S&F aluminium wire cloth with 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium stapple, complete all as specified and directed.

S&F Factory made Solid PVC Door Frame of size 50x47 mm made out of 5.0 mm thick plain colour PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Factory made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Square Tube for Top and Bottom Rails, mild steel Frame shall be covered with heat moulded plain colour PVC 'C' Channel having PVC Sheet Strip 20 mm wide stuck inside with Solvent Cement for Styles and plain colour PVC Sheet for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail, Bottom Rail Panelling of plain colour PVC Sheet to be fitted in mild steel Frame welded/sealed to the Styles and Rails with suitable Sheet Beading and jointed together with Solvent Cement and fixing in the Frame at Site as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F for PVC ventilators frame work with multiple chamber hollow PVC section comprising of DWUF 405(40x46mm)(3 mm) pin headed glass using extruded PVC section having dia of 0.9x14.5mm EDPM gasket, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheetng 0.50mm thick of an colour having tensile strengthof 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F of pre-painted colour galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for Anodised aluminium/ GI snap grid power coated framed work of size main runner 39x24.70x0.80 mm, cross tee size 29.x24.70x0.80 mm, wall angle 22.2x22.2x0.65 mm and size of grid 605x605 mm for false ceiling with 4mm thick GI suspender complete all as specified and as directed.

M&L for 4mm thick Non Asbestos designed fibre cement building boards fixed or laid/inserted to timber/GI/ Aluminium framework with screw in ceiling flat or sloping, complete all as specified and as directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410-W(Gde-E-250) quality A, complete all as specified and as directed.

M&L for Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.conforming to Fe-410-W(Gde-E-250) quality A, complete all as specified and as directed.

M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges, large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; wind ties, hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

M&L for MS Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde-E-250) quality-B complete all as specified and as directed.

S&F mild 11 to 15 mm mm steel screw bolts with hexagonal or square heads at one end and screwed the other and screwed end to be fitted with washers, one nut,complete all as specified and as directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and as directed.

S&F 100mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and as directed.

S&F aluminium alloy 200mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified and as directed.

S&F 100mm MS butt hinges medium weight, complete all as specified and as directed.

S&F aluminium handle cast type anodised 150mm size, complete all as specified and as directed.

S&F aluminium handle cast type anodised 100mm size, complete all as specified and as directed.

S&F 15mm bore GI tubing, medium grade with all fitting and fixed to wall and ceiling or laid in floor, complete all as specified and as directed.

S&F 20mm bore GI tubing, medium grade with all fitting and fixed to wall and ceiling or laid in floor, complete all as specified and as directed.

S&F 25mm bore GI tubing, medium grade with all fitting and fixed to wall and ceiling or laid in floor, complete all as specified and as directed.

S&F 25 mm Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed, complete all as specified and as directed.

S&F 15mm bore bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule complete as directed and specified.

S&F 15 mm bore stop cock, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore of pipe fixed complete all as specified and directed.

S&F PVC connections pipe 15mm bore size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle/push flush type brackets etc complete all as specified and as directed.

S&F vitreous china squatting Orissa pattern Water closet, size 630x450 mm white, with 'P' or 'S' Trap, integral foot rests etc. complete including making good to floor, complete all as specified and as directed.

S&F 15 mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe and fixed , complete all as specified and directed.

S&F vitreous china wash hand basin, white size 550 x 400 mm incl bracket & waste coupling complete all as specified and as directed.

S&F 32mm bore dia Waste coupling of PTMT (half or full threaded) minium weight 45 gms), complete all as specified and as directed.

S&F 100mm dia PTMT grating, complete all as specified and as directed.

S&F 75 mm thick PVC (SWR pipes single socketed in any length with rubber ring joints laid in trenches or floors, complete all as specified and as directed.

M&L for 100 mm bore for cast iron Nahani trap with grating incl jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and as directed.

S&F PVC (SWR) 110 mm bore (dia) Soil, Waste and Ventilating Pipe, double Socketed, in any length with Rubber Ring Joints, fixed to walls or laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) 110 mm bore (dia) Bend any type any radius, and jointing with Solvent Cement , complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Vent Cowl, jointing with Solvent Cement and fixed, complete all as specified and as directed.

M&L for Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity (Cylindrical, Vertical with Closed Top), 3 layered, hoisted and fixed in Position all as specified in MES Schedule , complete all as specified and as directed.

S&F 20 mm dia ball valves, PTMT high pressure of epoxy coated Aluminium rod and high density plastic ball (200 gms) complete, screwed for iron pipes or brasas ferrule and fixed complete all as specified and as directed.

Supplying, laying and testing of 100 mm internal dia of double wall corrugaed (DWC) high density polythylene pipe (HDPE) and stiffness classes 8 (SN-8) with ISI marked (With CML No ) with and including all fittings & jointing materials for connection of inspection chamber/WC to first manhole of the sewage line complete all as specified and directed.

M&L Cutting into existing manholes of 150 mm dia for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required, complete all as specified and directed.

M&L 15 cm thick (compacted thickness) WBM in two layers (75mm thick in each layer), with coarse aggregates of grading 2( 63 to 40mm size) of grading basalt or tap stone spread, watered, rolled consolidated to gradient and camber required 8-12 tone power roller capacity complete all as specified and directed.

M&L for cement concrete work in pavement/ hard standing of flexural strength 40 kg/Squre centimeter in field using 400 kg of cement per cubic metre thickness of concrete 25cm or less, complete all as specified and directed.

M&L providing & fixing 150 micron thick polythene flim laid in floors complete all as specified and directed.

M&L finishing the concrete surface/pavement by brooming while concrete is in green,complete all as specified and directed.

M&L for forming 20 mm thick expansion joints 200mm deep filled with pre form bituminus filler and top 30 mm primed and sealed with sealing compound Grade A, complete all as specified and directed.

M&L for forming Contraction (Dummy) joints 50mm deep x 10mm wide, filled with sealing compound Grade A, complete all as specified and directed.

M&L for 12 mm thick pre laminated particle board, interior grade prelaminated one side with decorative choice lamination &other side balancing white lamination fixed in screws to timber frame work, complete all as specified and as directed.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and as directed

M&L for preparing new plastered surfaces of walls and applying two coats of Cement Base paint over a coat of primer, complete all as specified and as directed.

Preparation of new or previously untreated wood surfaces of any description, over 10 cm width or girth, not otherwise described appling one coat of pink primer over applying two coat of synthetic enamel paint, complete all as specified and as directed.

M&L for preparing new or previously untreated Steel and Iron Surfaces of any description, over. 10 Cm Width or Girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

Material & Labour for preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @2.20 litre/ 10 sqm over new surface over 1 mm thick wall care putty, complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting over 1 mm thick wall care putty on plastered surface incl preparatory to distempering, complete all as specified and directed

M&L for complete removal of old surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting over 1 mm thick wall care putty on old plastered/putty surface incl preparatory to distempering complete, all as specified and directed.

M & L for Point wiring with 1.5 Sq mm copper conductor single core FRLSH PVC insulated unsheathed 1100 Volts multistranded drawn through and including rigid PVC Casing Capping and its accessories of suitable size, high grade ISI marked in walls /roof and PVC boxes of suitable size including fixing/grouting sunken/ surface as per site requirement for mounting the switches / sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLSH PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for : One light point controlled by one, one way switch 5 Amps, complete all as specified and as directed.

All as per item No 105 above but One ceiling fan / exhaust fan point controlled by one , one way switch and regulator, complete all as specified and as directed.

All as per item No 105 above but One 3 point 5 Amps socket outlets point controlled by one switch on the same board, complete all as specified and as directed.

All as per item No 105 above but One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

All as per item No 105 above but t with two run of 2.5 sqmm multi stranded Single core copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with one run of FRLSH PVC 2.5 Sqmm multi standard insulated sheathed copper wire as earth continuity conductor along with wiring and connecting to the common earth dolly on independent board.

M&L Point Wiring with 1.5 Sqmm Copper Conductor single core PVC insulated Flame Retardant Low Smoke (FRLSH) Unsheathed 1100 Volt grade multi-stranded Cable drawn through and including Concealed Rigid PVC Conduit, medium grade, ISI marked of suitable size and its Accessories as required at Site, fixing on surface of Wall, Roof, mounted on Sunk Mild Steel Pressed Terminal Box 1.22 mm thick of suitable size duly painted with red oxide metal primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, etc. including PVC insulated and unsheathed Single Core multi-stranded Copper Conductor Cable of size 1.5 Sqmm (FRLSH) Green in Colour as Earth Continuity Conductor connected to Common Earth and Earth dolly for One Light Point controlled by One 1-Way Switch 5 Amp, complete all as specified and as directed.

All as per item No 110 above but for one Ceiling fan / Exhaust Fan point controlled by one, one way switch and regulator, complete all as specified and as directed.

All as per item No 110 above but One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board, complete all as specified and as directed.

S&F Switch piano flush type single pole one way 5 Amp, 230 Volts, complete all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 Amps complete all as specified and directed.

S&F Switch socket combination flush type multipurpose 2/3 pin 5 Amps two in one , 230 volts, complete all as specified and as directed.

S&F Switch socket combination 2 in 1, 3 pin, 15 Amp flush type universal, complete all as specified and as directed.

S&F ceilling rose three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm, complete all as specified and as directed.

S&F ceiling fan regulator step type, flush type heavy duty suitable to work on 230 Volt AC supply, complete all as specified and as directed.

S&F sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door with magnetic locking system,complete all as specified and as directed. Make : Model No. DBTPE004DD of L&T or equivalent in Schneider/Indo asian/Legrand.

S&F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 63 amps complete all as specified and directed. Make : Model No. BB40630C of L&T or equivalent in Schneider/Indo asian/Legrand.

S&F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, C-curve, complete all as specified and directed. Make: Model No. BB10060C,BB10100C,BB10160C of L&T or equivalent in Schinder/Legrand.

S&F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified. Make : Model No. DBSPN006D of L&T or equivalent in Legrand/Indo Asian.

S&F MCB Double Pole 20 Amps 240/415 Volt, confirms to IS/IEC 60898 Braeking Capacity of 10 kA, C-curve, complete all as specified and directed. Make : Cat No. BB20320B of L&T or equivalent in Schinder/Legrand.

S&F wall mounted LED 18 watts, Batten type T 8 light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including Ultra bright LED polycarbonate (T8) tube (Single side connection) 4' x 18 watts with G13 lamp holder complete all as specified and directed. Make: Model No. REGALBATTENT8UPTO1X18WDSBSWH of Havells or equivalent in CG/Surya for Batten Fitting. Make : Model No. PHOTONULTRAE2.01213T8SSTL18WLED865SPC of Havells or equivalent in CG/Surya for T8 Tubelight.

S&F Recess mounted Environmental friendly ,asthetically designed ,ultra modern 2X2 slim luminaire 36W with high brightness SMD LED as Light source,suitable for Armstrong /Grid ceiling , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including suitable LED Driver complete all as specified and directed. Make : Model No. STRATO 2X2 of Havells or equivalent in Crompton/Surya.

Supply & Laying well burnt brick, locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified and directed.

Supply & Laying LT heavy duty UG Cable of size 16 Sqmm 4 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed.

S&F GI Tubing, light grade of size 32mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clam as per site requirement etc complete all as specified and directed.

Supply & lay GI tubing, 40 mm dia, light grade in protection of cable at road crossing /hard standing/pole protection fixed with clamps as per site requirement etc complete all as specified and directed .

M&L for Sub main wiring 2 x 6 Sqmm multi-strand FRLSH PVC insulated copper conductor unsheathed cable including concealed conduit and continuous earth wire of FRLSH PVC insulated multi-strand copper conductor of size 6.0 sqmm. Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles, complete all as specified and directed.

S&F for single pole and neutral enclosure with a two pin and earth plug and socket complete with on one single pole MCB 20 Amp, 240 volts, complete all as specified and directed.

S&F 5 star rated BLDC ceiling fans AC 230 Volts single phase 1200 mm sweep complete with all accessories including MS Hook, Nuts, Bolts and washer for hanging arrangement complete all as specified and directed. Make : Model No. TECHNO AIR 5 Star of Usha or equivalent in Havells/Crompton

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 metre below the road surface) with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under relevant Item.

S&F lamp holder insulated body surface bakelite with back plate suitable for angle / batten fittings fixed with PVC round/square blocks complete all as specified and directed.

S&F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified and directed. Make : Cat No. LHLDEUEBML8Z010 of Havells or equivalent in CG/Polycab.

S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as specified and directed. Make : Model No. ENDURAPEARLSL25WLED757SASYTOPCMP of Havells or equivalent in CG/Polycab.

S&F heavy duty exhaust fan 300 mm sweep MS Body, 3 wing 1400 rpm, single phase 240volts copper wounds complete with all accessories as louvers shutters etc incl making connection through 3 core PVC copper wire run through flexible pipe. Single phase type, complete all as specified and directed.

Supply & Laying LT UG XLPE cable of size 2 core x 10 sq mm laid in trenches/ floors/ on wall/ service connections PVC insulated, sheathing and armoured 1100 volts grade with aluminium conductor with necessary end terminal/ cable gland as per site requirement including connecting to the main switches/ cut outs MCB/ MCCB with necessary lugs after cutting to required length of cable, complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode size 600x600x6.0mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised earth lead wire 4.0 mm dia means of bolts, nuts, check nuts and washers of galvanised steel and GI pipe light grade 20mm dia bore for watering funnel with wire mesh refilling with vegetable soil without bolders and stones, gravels and aggregate etc,and CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point or indicated including testing on completion, complete all as specified and directed. NOTES : The unit rate includes for protection pipe and GI wire 4mm dia from top of earth plate up to 5.00 meter above ground level.

S&F 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 40 mm Outer dia, ISI marked, SDR 7.4 and SDR 11 UV Stabalised and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and directed.

S&F 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 32mm Outer dia, ISI marked, SDR 7.4 and SDR 11 UV Stabalised and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed.

S&F PP-R Gate Valves (Brass Insert) 32mm outer dia and fixed, complete all specified and as directed.

S&F PP-R Gate Valves (Brass Insert) 50 mm outer dia and fixed, complete all specified and directed.

Making connection of PP-R distribution branch with PP-R main of 63 mm size by providing and fixing tee of 40 mm x 32 mm including cutting and making fusion joint etc, complete all as specified and directed.

Sunrise Enterprise

R D ENTERPRISE