Upgradation and Renovation of Nalukettu Rooms and Palace rooms at Bolgatty Palace and Island Resort Kochi_Civil ELectrical and ELV works

Dismantling wooden flooring including with underlay foam, trimming and joint sealant, but including stacking with in 50 metres lead: of any Thickness including leading 50 m and stacking the same as directed by the departmental office at site .Details of cost for 10 sqm

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling granite work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 20 mm and up to 40 mm

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 or leaner mix ( including equivalent design mix)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead:Of sectional area 40 square centimetres and above

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area beyond 3 sq. metres

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking with in 50 metres lead:Thickness above 25 mm upto 40 mm

Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

Dismantling and removing all sanitary and plumbing fittings of existing toilet such as wash basin, closet, taps, shower arms, health faucet, angle clock etc.removingcarefully stacking in convenient places pointed out by the engineer in charge for reuse including disposal of all debris outside KTDC premises and cutting and removing all projected parts of existing pipes and fittings etc.and making all the surfaces ready for fixing new fittings to wall tile etc.complete.

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL antitermite treatment (excluding the cost of chemical emulsion): Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement :2 coarse sand ) to the full depth of the hole:With Chlorpyriphos /Lindane E.C 20% with 1% concentration

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc.

Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Filling floors of bathrooms with cement sand mixture in the ratio 1:15, compacting, etc. complete

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

Providing and fixing white vitreous china flat back/half stall urinal of approved quality and make (Jaquar/Kohler equivalent) with automatic sensor flushing system, complete with spreader, CP brass flush pipes, inlet/outlet connections, and all fixing accessories, including cutting and making good of walls/floors as required and connection to waste pipe and water supply, all as per manufacturer?s specification and direction of Engineer-in-Charge. MODEL :- URS-WHT-13267S

Supplying and fixing Auto Closing Concealed Urinal Flush Valve with Wall Flange of make Jaquar or approved equivalent as per direction of engineer in charge. The rate includes all material cost, labour charge etc complete

Providing and fixing urinal division plate/partition of Jaquar or approved make as per direction of Engg-in-charge

Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineerin- Charge. External work32 mm nominal dia pipes.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x63 mm dia Reducer

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia 45 degree Elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in- Charge. External work40 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in- Charge. External work50 mm nominal dia pipes

Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 meters lead:With cement mortar 1:4 ( 1 cement : fine sand)

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Door Elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee

Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75x75x75 mm dia Door Tee

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints compete as per direction of Engineer in Charge. 40 mm dia 6 Kgf/cm2

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 10Kgf/cm2

Supplying and fixing approved make C.P. towel rail with necessary fixing materials Jaquar Make - ACN-1111SM

Supplying and fixing CP towel rack 600 mm long with out lower hangers but 3 hooks with stainless steel (Jaquar/ equivalent)) including cost, fixing charges etc complete (Model No: CAN 1181FHS)

Supplying and fixing in position Robe hook - double coat hook (model No. AKP- 35761P of Jaquar), including cutting & making good the walls ,cost and conveyance of all materials and labour charges for fixing etc. complete.(DAR-18.65 Based)

Supplying and fixing in position C.P. Cloth Liner Retractable of Jaquar make, including cutting & making good the walls ,cost and conveyance of all materials and labour charges for fixing etc. complete. (DAR-17.73.1 Based)

Supplying and fixing approved make C.P. towel ring with necessary fixing materials Basic cost = 480, Jaquar Make - ACN - 1121BN

Supplying, Installing, testing and commissioning approved make 15mm CP shower unit comprising of CP 15mm dia single lever divertor with CP spout, overhead shower set comprising of CP shower arm, rose etc.,complete with CP wall flanges. Jaquar/equivalent

Supplying and fixing Toilet Roll Holder (Jaquar/equivalent) of approved quality including cost, fixing charges etc complete

Providing and fixing Disabled-Friendly Wall Hung Wash Basin (Model DIS-WHT- 93801 or approved equivalent) of white vitreous china, size as per manufacturers design, with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including cutting and making good the walls wherever required. The rate shall include supply and fixing of a pair of 15 mm C.P. brass pillar taps, painting of fittings and brackets, labour, materials, testing and all accessories complete, as per direction of Engineer in- Charge. ( BASED ON 17.7.3)

Supplying, fixing, testing and commissioning approved make wash basin white colour fixed below counter with 32mm dia CP waste coupling, 32mm dia C.P.bottle trap with C.P. extension pipe, 1 No. 15mm dia C.P. angle cock 1 No. C.P. flexible inlet connection pipe G.I. expansion bolts etc., complete including jaquaar masin mixer silicon sealant Basic cost of wash basin = 2400 & Pillar Cock = 1750, Referred Model Jaquar Make wash basin - Code : LAS-WHT-91701

Supplying and fixing single lever wash basin mixer (JAQUAR) or equivalent of approved quality including cost, fixing charges etc complete (Model No:ARI-CHR- 39051B)

Providing & fixing of white colour ceramic Table top wash basin (made of Jaquar Designer model No. AIS-WHT- 101903 OR Kohler) complete as directed by KTDC. Bottle trap (Jaquar Model) 32mm size with 300 mm and 190mm long wall connection pipe and wall flange, Angle cock(KUB-35053F) ( 2Nos for hot & cold water), 450mm braided hose with nipple, nut, O-ring rubber washer suitable for basin mixer ( 2Nos for hot & cold water), including all accessories for fixing wash basin etc.complete (quality and brand as approved by the KTDC) . The rate includes cost and conveyance of all materials , all labour charges etc. complete (DAR-17.7.2 Based)

Supplying, fixing, testing and commissioning of Sensor Operated Wash Basin Faucet Jaquar Kubix Prime (Code: SNR-CHR-35019PM) or approved equivalent, battery operated, chrome plated, complete with sensor mechanism, battery pack, solenoid valve, aerator, and all standard fittings. The rate shall include supply of materials, labour, fixing accessories, connection to water supply, and testing complete as per direction of Engineer-in-Charge.

Supplying, fixing, testing and commissioning approved make wash basin (white colour fixed table top) with 32mm dia CP waste coupling, 32mm dia C.P.bottle trap with C.P. extension pipe, 1 No. 15mm dia C.P. angle cock 1 No. C.P. flexible inlet connection pipe G.I. expansion bolts etc., complete including jaquaar masin mixer silicon sealant Basic cost of wash basin = 2400 & Pillar Cock = 1750, Referred Model Jaquar Make wash basin - Code : JDS-WHM-25907N

Supplying and fixing Pillar Cock Chrome plated of make Jaquar (Range: Kubix Prime, Code: KUP-CHR-35021PM) or approved equivalent, including all necessary fittings, connection to basin, testing and commissioning complete as per direction of Engineer-in-Charge. The rate shall include cost of materials, labour, and making good any disturbances complete.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

Supplying and fixing Jaquar ACN-1135N Soap Dispenser with Glass Bottle etc. complete.

Providing and fixing wall mounting European water closet with seat cover (white colour) , size 350x360 x 535 mm model Jaguar-(Jaquar model Bowl, seat cover & Slim Concealed Cistern With Floor Mounting Frame, Installation Kit and Drain Pipe Connection Set for Wall Hung WC including Cotrol Plate Moon Design All Chrome or Equivalent of approved shape with 'P' trap, of removable soft matching seat cover with Auto closure, Fixing of the above closet with stainless steel rack bolt (seam bolt ) white cap etc. complete with supply of Brass Pan connectors, noise reduction gasket & necessary fasteners. Providing water & Soil connections to the closet, together with cutting and making good the walls and floors wherever required, quality and brand as approved by the KTDC, etc. complete. Providing & fixing WC Connection Socket with lip seal (Quality controlled in accordance with DIN 1389),including all acessosories and making good all damages and closing the bottom side of the closet using 6mm thick multiwood of required size with silicon sealant with no gaps and projection etc.complete.(quality and brand as approved by the KTDC) The rate includes cost and conveyance of all materials , all labour charges etc. complete.

Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Supplying, fixing, testing and commissioning of Differently Abled Rimless European Water Closet (Coupled WC) with Cistern, complete with UF soft close slim seat cover, hinges and fixing accessories, P-trap 180 mm, size 380 x 650 x 790 mm, white glazed finish, of make Jaquar (Model DIS-WHT-93951UF) or approved equivalent, as per direction of Engineer-in-Charge. The rate shall include all material costs, cistern, seat cover, labour, installation, fittings, connection to soil line, and testing complete in all respects.

Providing and fixing foldable wall-mounted shower seat of approved make and design, made of high-strength waterproof U-PVC/HDPE seat with anti-slip slats, mounted on heavy-duty SS 304/316 grade foldable brackets, including stainless steel anchor fasteners, fixing on concrete/brick wall, proper alignment, testing, and making good the surface complete as per direction of Engineer-in-Charge.

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing and fixing Tile/Marble Insert Type Floor Drain of size 150x150 mm, made of high-quality Stainless Steel Grade 304, suitable for bathroom, balcony, terrace, or floor areas. The drain shall be of tile insert type allowing floor tiles/marble to be inset flush for a concealed and seamless finish. The unit shall include an SS304 outer frame, removable tile tray, and outlet connection (typically 75 mm or 100 mm diameter), but without cockroach trap.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadeOld work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge. Second class teak wood 35 mm thick shutters

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Inserting float glass panes of nominal thickness 5 mm in prepared openings of new wooden door shutter, including careful fixing , minor finishing, and cleaning of glass surface, all complete as per the direction of Engineer-in-Charge.

Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge. Second class teak wood30 mm thick shutters

Providing and fixing glazed shutters for door, windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S. Pressed butt hinges bright finished of required size with necessary screws. Second class teak wood30 mm thick

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door including Door handle (Dorma TGDIH 600 x 32 S Grade 304 /equivalent), lock ( Xlc - 7058 Glass to Glass Lock One Key One Knob/ equivalent) and floor spring (Dorma BTS 75 90* W /D/equivalent) etc all complete as per direction of Engineer-in-charge.

Providing, fabricating and fixing sliding type cubicle partition for wash area using 8mm thick toughened glass panels with polished edges, including all necessary stainless steel (SS 304 grade) fittings and fixtures in chrome finish such as sliding rails, rollers, wall brackets, stoppers, handles, locks, guides and required accessories, complete as directed by the Engineer-in-Charge

Taking out and dismantling existing toilet cubicles including partitions, panels (laminate /ply/glass), aluminium/SS framing sections, doors, fixtures, and all fittings, carefully without causing damage to adjacent flooring, wall tiles, and plumbing lines. The dismantled materials shall be stacked or disposed of as directed by the Engineerin- Charge. The rate includes labour, tools & tackles, and all incidental charges complete.

Providing and laying factory-finished Pergo or approved equivalent brand Laminated Flooring 10mm Thickness of AC5 Grade with water resistance property using 35GSM Polyethylene Sheet and 2mm EPE Polyfoam as underlay, trimming and joint sealant, complete as per manufacturer’s specification and engineer-incharge&# 39;s instructions.

Providing and laying Full body vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS :15622, of approved make, in all colours and shades, laid on 20 mm thick cementmortar 1:4(1 cement : 4 coarse sand), excluding grouting the joints with white cement and matching pigments etc.(Payment for grouting of joints to be made separately), complete.Size of Tile 1200 x 600 mm.

Providing and laying vitrified Wall tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, using tile adhesive , including providing tile level Spacers of size 3mmetc. Size of Tile 1200x600 mm (Basic price of tile not less than Rs. 135/sft)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), excluding grouting the joints with white cement and matching pigments etc.(Payment for grouting of joints to be made separately), complete. Size of Tile 1200 x 600 mm.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 1200x600mm

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing 8 mm thick toughened glass for Glazed window shutter of approved brand and manufacture, all complete as per direction of Engineer-in-Charge (window frame, hinges, handles, locks, stoppers, and other fittings to be paid separately).

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shadeArea of slab upto 0.50 sqm.

Providing edge moulding to granite stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Marble work

Supply and fixing of Main Door Sensor Lock (Ozone or equalant brand). The rate shall be inclusive of cost of materials, labour charges etc., all complete. All the materials to be used on the work shall be approved by the Engineer-in-charge.

Supply of second class teak wood wardrobe as directed by the engineer in charge in sliding/opening doors per the design provided. Including rates of handles, aluminium channel for sliding door ,hanging rod ,finishing with two coats of melamine (glossy/matt finish) polish, all loading and unloading charges, all conveyance etc as Directed by Departmental Engineers.

Teak wood framed Wooden Bed side table of size 45x45x45cm or nearest size with double drawer and brass ornamental handles, locks and knob for all rooms duly finished of Teak wood frame as per the design provided. Wood surface shall be sanded smoothly with two coats of sealer applied and finished with two coats of polyurethane / melamine ( glossy/matt finish) in teak finish.

Supplying and fixing PVC floor trap of required specifications as per site conditions including charges for chipping floors and making good the floors after fixing the trap, etc. complete

Item: Providing and fixing wall-mounted stainless steel grab bar, 32 mm dia and 600 mm long, made from SS 304 grade tube, brushed finish, with concealed wall flanges fixed on tiled/concrete wall including drilling, alignment, and finishing the joint with white cement or epoxy grout, complete in all respects.

Providing and fixing wall-mounted foldable grab bar, suitable for elderly, pregnant women, or differently-abled persons. The grab bar shall be made of high-grade stainless steel (SS 304) with folding hinge mechanism, safety lock, and optional nylon anti-slip grip coating. Work includes all accessories, fixing with stainless steel anchor fasteners, and finishing, complete as per direction of Engineer-in-Charge.

Supplying and fixing the teak wood bed cot head board set with size of 3688 x 1200 mm or the nearest available size as per the design.including the rates of upholstery ,two coats of melamine (glossy/matt finish) polish, all loading and unloading charges, all conveyance, etc., as directed by Departmental Engineers.

PU(Single Pack Exterior Grade )Polish: Preparation of wood surface for polishing as<br> per the follwoing procedure:1. Filling the holes and screw marks in the wood surface using Wood filler and sandering the surface using 80 grade paper 2. Applying First coat Sanding Sealer 3. Filling the Joints using Filler Powder and sandering with 120 grade paper 4.Applying second coat Sanding Sealer and sandering with 220 grade paper Apply 2 coat single pack PU polish to obtain smooth surface.

Providing and fixing King Size Cot four poster cot & matress (1.93m x 2.03m)

Supplying and providing good quality cylindrical lock(KEYLESS) of approved make. The rate including all material cost labour charge etc completed.

Supplying chair size of 605 X 630 X 775 mm or nearest available size as per the design provided .Including the cost of all loading and unloading charges, conveyance, etc as Directed by Departmental Engineers.

Providing and placing traditional wooden slatted bench made of premium quality seasoned teak wood, placed at the foot of the bed, designed in classical Kerala /Nalukettu style with curved arms and turned legs.

Supplying and placing premium-quality 4-seater round dining Teak table set artificial marble top with suitable for restaurant use, comprising one solid hardwood (seasoned teak or equivalent) dining table of size approximately 900 mm × 900 mm × 750 mm height, with polished finish and chamfered edges, along with 4 matching ergonomically crafted dining chairs with contoured backrests and cushioned seats upholstered in high-grade leatherette or fabric, all finished with melamine/PU polish, complete as per approved design, including transportation, handling and installation at site.

Supplying and placing premium quality restaurant chair of approved make and design, constructed with solid teak wood frame, high-density foam cushioning (minimum 40 kg/m³), upholstered in stain-resistant fabric/leatherette of approved shade, with PU polish for wood parts. Chair to be ergonomically designed for comfort, with smooth edges, sturdy joints, and felt pads for floor protection, complete in all respects as directed by the Engineer-in-charge.

Supply and fixing Cushion Cover of 450 x 450mm same fabric of Curtain as directed by the Engineer in charge.

supplying and fixing brass ovel shaped number plate with lettering 125mm 3mm thickness as per approved pattern including cost of material and labour

" supplying of 40 x 40 cm small pillow using with recornfilling <br& gt;" <br>

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer heay type forr wooden shutter (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 900 mm), with necessary accessories and screws etc. complete as specified by the Engineer at site.

Mirror polishing on marble work/ granite work/stone work where ever required to give high gloss finish complete.

Supplying and placing premium single bed mattress of approximate size 1980 mm × 915 mm × 150 mm (6.5' × 3' × 6"), manufactured using multi-layered core construction comprising high-density rebonded foam (min. 40 density), a soft HR foam comfort layer, and a memory foam topper, enclosed in a quilted, breathable, anti-bacterial and fire-retardant fabric cover, with side ventilation mesh and edge reinforcement. The rate includes cost of all materials, handling, transport, unpacking and placing in position in rooms as directed by the Engineer-in-Charge.

Supply and fixing Bed Runner with Lining same as Curtain fabric as directed by the Engineer in charge.

Repairing and restoring existing wooden cots of all size including tightening or replacement of loose/damaged bolts, realignment of legs and frame, replacing missing/ broken wooden slats or plywood base with seasoned wood minor sanding and application of wood sealant or PU touchup as required, including materials, skilled labour, tools and repositioning at site as directed by the Engineer-in-Charge.

Taking out the existing wooden glass door and refixing the same after necessary repair works. The repair works including providing and fixing floor spring (Dorma BTS 75 90* W /D/equivalent) and Doorhandle(Dorma TGDIH 600 x 32 S Grade 304 /equivalent) matching to the existing holes, lock ( Xlc - 7058 Glass to Glass Lock One Key One Knob/ equivalent) and etc all complete as per direction of Engineer-incharge. Detailed cost for 5.32 sqm

Repairing and restoring existing wooden furniture Luggage Rack including tightening or replacement of loose/damaged bolts, realignment of legs and frame, replacing missing/broken wooden slats or plywood base with seasoned wood or marine plywood, minor sanding and application of wood sealant or PU touchup as required, including materials, skilled labour, tools and repositioning at site as directed by the Engineer-in-Charge.

Repairing and restoring existing wooden furniture ( study table)including tightening or replacement of loose/ damaged bolts, realignment of legs and frame, replacing missing/broken wooden slats or plywood base with seasoned wood or marine plywood, minor sanding and application of wood sealant or PU touchup as required, including materials, skilled labour, tools and repositioning at site as directed by the Engineer-in-Charge.

Repairing and reupholstering existing wooden or cushioned chair including tightening or replacement of fasteners, strengthening of joints, realignment of legs/backrest, replacement of broken slats if any, removal of old upholstery and fixing new highdensity foam (min. 32 density) cushion with premium fabric (min. ?300/sqm rate), stitching and tacking, polishing/touchup of exposed wood surface with melamine/PU coat, and repositioning in place, all complete including skilled labour, materials, transport and tools as directed by the Engineer-in-Charge.

Repairing and restoring existing wooden furniture Coffee table including tightening or replacement of loose/damaged bolts, realignment of legs and frame, replacing missing/ broken wooden slats or plywood base with seasoned wood or marine plywood, minor sanding and application of wood sealant or PU touchup as required, including materials, skilled labour, tools and repositioning at site as directed by the Engineer-in-Charge.

Taking out existing wooden door shutter, repair by cutting, and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Repairing and restoring existing teak wood wardrobe (single or double shutter), including removal of faulty shutters, replacement of damaged hinges, knobs, magnetic catches, tightening/replacement of fasteners, re-alignment of door panels, repair or replacement of internal shelves using seasoned wood or BWP-grade marine plywood, application of PU/melamine polish touch-up on exposed surfaces, cleaning and re-fixing at site ? all complete with labour, minor materials and tools, as directed by the Engineer-in-Charge.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured).

Supplying shear curtain fabric of approved make and design as per the directions of Engineer in charge. (Basic price shall not be less than Rs.250/m)

Stitching and fixing pleated shear curtains in to position using M-Track of Heavy duty aluminium section of approved design and size after dismantling the existing curtain rods. Rate including transportation, all material cost, stitching charges, labour charges, accessories etc. complete. (Rate excluding cost of Fabric)- length of M-track considered for payment purpose only.

Supplying main curtain fabric of approved make and design as per the directions of Engineer in charge. (Basic price should not be less than Rs.650/m)

Stitching and fixing in to position i-lite curtains using 304 grade SS tubes of 25mm dia with SS caps/finals, SS hooks, SS i-lite rings of approved design on both side hydraulically pressed in to fabric (including blackout) including transportation, all material cost, stitching charges, labour charges, accessories etc. complete. (Rate excluding cost of Fabric)- length of drapery rod considered for payment purpose only.

Supply and fixing of corean top buffet counter in Greenlam 19mm thick plywood and lamination including all cost conveyance and labour charges for making and fitting as directed by the partmental officer at site. size (2.40m * 0.75m)

Supply of Teak Wood Mini Bar Unit as per design including Wood surface shall be sanded smoothly and two coats of sealer applied and finished with two coats of polyurethane melamine (glossy/matt finish) polish, all loading and unloading charges, all conveyance etc as Directed by Departmental Engineers.

Item for providing and fixing a wooden roof truss including purlins, rafters, tie beams, ridge pieces, etc., suitable for traditional or Kerala-style architecture using hardwood like Anjili or equivalent seasoned timber.

Providing and fixing 0.30mm thick Aluminium Sheet on tiled roof using with nails including 150mm over laps, all cutting charges, all labour charges, all conveyance all leads and lifts etc. complete as per the Directions of Engineers at site. Details for 1.0m2 - 1.15 x 0.810kg/m2=0.932kg

Providing & fixing Poly carbonate solid sheet 4 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size (5.5x55mm) with EPDM seal complete upto any pitch in horizontal / vertical / curved surfaces, but excluding the cost of purlins, rafters, trusses and including cutting to size and shapes where ever required.

Providing and fixing roofing with 0.50mm thickness coloured galvanised iron Tiled profile sheets (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) . Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curvedsurfaces, excluding the cost of purlins, rafters and trusses and including cutting to sizeand shape wherever required.ng/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape where ever required

Supplying, fabricating, and fixing cast iron handrails, including balusters, rails, ornamental panels (if any), base plates, holdfasts, etc., made from standard cast iron sections of approved design and size, installed at staircases, balconies, or corridors.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

Engaging labour for carrying out miscellaneous works at site, including loading, unloading, shifting of materials, assisting in civil/plumbing works, site clearance, cleaning, and other allied works as directed by the Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

Painting with PU Enamel paint of approved brand and shade over a coat of PU sealer /primer on wooden surface (furniture, paneling, etc.) including surface preparation, two or more coats, complete as per engineer’s instructions.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

Cleaning of Mangalore tiles by carefully bringing them down from the roof, washing with water to remove dust, moss, algae, and other deposits, and carrying them back to the roof level for re-fixing in position as directed by the Engineer-in Charge. (Double Side)

MP roofing tile painting with Apex tile guard paint paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ).

Provision of single scaffolding (MS pipe type, non-cuplock) for executing elevation works such as painting, rectification, putty application, dismantling, and other associated works. Scaffolding erected to full height to enable safe access for workers. Includes verticals, horizontals, bracing members, base plates, and safe working platforms. The scaffolding is fixed firmly to ensure stability and safety during execution.

Supplying and fixing Hittich Built -in ironing board ( model no :360-468) as Directed by Departmental Engineers.

Supplying Arm Chair of 530 X 630 X 775 mm or nearest available size as per the design provided (Specification :Hardwood with teak wood finish. Cushion with jute material.) Including the cost of all loading and unloading charges, conveyance, etc as Directed by Departmental Engineers

Supply and fixing second class teak wood luggage rack of size 600 X 1000 X900 mm or nearest available size as per the design provided. Rate excluding cost of tandem slider of 400 mm. Including the rates of finishing with two coats of melamine (glossy/ matt finish) polish, all loading and unloading charges, all conveyance etc as Directed by Departmental Engineers.

Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Supply & Fixing of Bangalore Stone 60 x 60 cm (Box cut) of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge

Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the 'W' profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish.8 mm thick cement fibre board as per IS : 14862

Supplying & fixing teak wood circular mirror size of 670 mm dia or the nearest available size as per the design provided .Including the cost of the mirror and finished with two coats of melamine (glossy/matt finish) polish, all loading and unloading charges, conveyance, etc. as Directed by Departmental Engineers.

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

Supplying and filling of Quarry muck including all cost, conveyance laying in low lying and water logged areas with etc complete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement Mortar 1:6 (1 cement : 6 coarse sand)

12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

Supplying and fixing Cast Iron Manhole cover with frame and locking arrangements of size 600x600mm (Medium -Weight Not less than 65kg/each) including all conveyance, all labour charges etc. complete.

Providing MBBR Meda - Type Corrugated round type, white color Surface Area 500 m2/m3 MOC Virgiin Plastic/polypropylene Specific Gravity 0.90 –0.95 gms/cm3 Voidage > 98%

Supplying and fixing Aeration Grid CPVC 1? dia piping network provided with holes etc. complete including all conveyance

Supplying and fixing Pressure Sand Filter FRP With Media 0.45m Dia x 1.6m ht Make : Pentair/Canature including all conveyance etc. complete.

Supplying and fixing Activated Carbon Filter With Media FRP 0.45m Dia x 1.6m ht Make : entair/Canature etc. complete. including all conveyance.

Supplying and fixing Screen (SS) including all conveyance etc. complete

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge using Anjili/ Jack wood

Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:250x10 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

CCTV SURVEILLANCE SYSTEM AND Wi-Fi NETWORKING INSTALLATION WORKS

Supply of Optical Fibre Cable 6 Core Armoured.

Supply and installation of Optical Fiber Media Convertor Single Mode Single Fiber (Type A & B)

SSupply and installation of 16 Port Gigabit PoE Ethernet Switch rack mounted (with 2 normal uplink).

Supply and installation of 8 Port Gigabit PoE Ethernet Switch.

Supply and Laying of 25mm HDPE Pipe (Standard ISI ) with all accessories such as saddles etc and complete.

Supply, Installation, Testing and Commissioning of Wall mounted 6U Rack along with power sockets strips and all other require components & acceessories.

Supply and Laying of 25mm PVC conduits/casing capping, (Standard ISI medium) with all accessories such as saddles etc and complete.

Supply and Installation of Indoor 4 Megapixel High Definition IP Dome Camera of good quality & approved make with 2560 × 1440@30fps resolution,4 mm lens, minimum 30 m IR range, H.264 Compression, Video bit rate 32 Kbps~16Mbps,2.54cm rogressive scan CMOS,PoE (Power over Ethernet), 120db Wide Dynamic range, 3D Digital Noise Reduction,Dual stream, DC12V & PoE (802.3af), IP67 Weather Proof, day/night vision,Auto, scheduled Day/Night Switch,RoHS ompliance etc.

Supply and installation of 1Mtr Patch Cord.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Supply and installation of Wi-Fi Access Point (Wall Socket- Dual band, PoE supported)

Supply and installation of 24 Port Gigabit Poe Network Switch. (1 port sfp with module,1port ethernet uplink).

Supply and Installation Optical Fiber Cable 6 Core (SC connector) Splicing Charges with termination box.

Any other Item Not included above but required to complete the Job.

Electrification works

Supply and wiring points according to IS732-1989 using rigid PVC conduit of minimum size 20mm with specials conforming toIS9537 partIII1983 andwith suitable sizespecials conforming toIS3419-1988, fixing theconduit usingmetal saddles spacing notexceeding 50cmorconcealed suitably and with 1.00 sqmm FRLSPVC insulated stranded singlecore copperconductor cable 650V grade, including providingswitchboardmainandcontinuous earthing withNo.14SWG barecopper,requiredquantity ofcopper earth socket, brass boltand nutcrimping/ solderingetccomplete with suitable size modular type metal switch boxes,modular type front plates(white) etc.upto and including 6A modular type SP switches and making good the surface of wall,colourwashing etc.complete.All the terminations in the switchboards and DB'sshall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitableties,tiemountsetcasrequired.(RoHS compliant modular accessories).Singlecontrol light point without ceiling rose- Medium point

Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm FRLS PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity of copper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular type metal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. (RoHS compliant modular accessories).Single control light point without ceiling rose - Long point

Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm FRLS PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity of copper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular type metal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. (RoHS compliant modular accessories).Single control light point without ceiling rose - Short point

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.0 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.0 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.4 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (l00mmX75mm)

Supply and installation of 16 A electronic key tag including all accessories, key fob card on existing modular box and giving connection etc complete as required at site

Supply and providing modular type skirting light of good quality in the existing MS box and giving connection etc complete as required at site

Installation, Testing and commissioning of DND-MMR module (Both external and internal) on existing MS box and modular plate including giving connection etc complete as required at site

Supply of modular type DND-MMR indicators with bell push (1+1) Module of good quality and reputed make (Both external and internal)

Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connection etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - three phase double cover (IP 42/43)

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required-6 way (8+18) - three phase double cover (IP 42/43)

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame)

Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

Supply and providing heavy duty 'A' section neoprene gasket in the panel boardA' section neoprene beeding suitable for 1.60/ 2.00 mm sheet

Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

Supply and providing copper earth bus in the panel board

Earthing related works

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt) as required

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG)

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 swG)

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.00 mm copper conductor ( 8 SWG)

Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run 25 x 3 mm copper strip

Light fittings

Supply & providing of 4.8W/m LED strip light of IP20 grade including suitable driver for use on 230V AC supply including all accessories required for fixing etc. complete of good quality and approved make in the existing coves including twin twisted plastic wire for lead interconnection etc complete

Supply, conveyance and providing good quality LED linear profile lighting including concealed type aluminium profile with profile LED strip and required capacity Driver unit suitable for indoor application

Supply of 3W LED recessed ceiling fitting type light fittings of good quality and reputed make

Supply of 6W LED recessed ceiling fitting type Light fitting of good quality and reputed make

Supply of bed side wall lamp fitting of good quality and reputed make. (Model: PHILIPS striker wall model no: 581876)

Supply of 1200 mm size decorative type BLDC fan of good quality and approved make

Supply of pvc low noise 300mm dial400 RPM single phase Exhaust fan of good quality and reputed make

Appliances

Supply of 60 Litre or nearest higher capacity vapour compression type minifridge/minibar working on 240V 50HZ AC supply

Supply of push button telephone for guest rooms

Supply of wall mounting telephone for using on toilets

Supply of cordless type 1.0 Litre or nearest higher capacity kettle for guest rooms having stainless steel body inside, concealed heating element, auto cut off & dry boil protection and working on 230V 50Hz AC supply.

Supply of 43 inch size 4K Ultra HD Smart LED Television sets with hospitality features having the following minimum specifications. Resolution ; 3840 x 2160, Brightness ; 250 nits , USB port ; 1 No.(minimum), HDMI/Optical Component connectivity, Contrast Ratio; 4700:1, Viewing Angle (H/V) 178/178 Response Time ; 8 ms .The LED TV set shall have Built-in Wifi, Bluetooth support, Built-in speaker, PC/DVD component connectivity, remote control and Wall Bracket etc complete. The TV should display hotel logo on welcome screen Warranty:- 3 years full warranty and shall be complete as per manufacturer Specification.

Fire fighting

Supply, fixing, testing & commissioning of bulb type pendent sprinklers of rating 68 degree centigrade with required accessories.

Supply, Fixing, Testing and Commissioning of side wall quick response extended sprinkler including accessories

Supply, Installation, testing and commissioning of wall mounted type PA speaker with talk back unit housed in a MS box with all mounting accessories

Supply, Installation, Testing and commissioning of horn cum strobe rated at 82 dBA @ 3m for audible announciation and 75 cd flashing at 1 Hz for visual indication.

Supplying, installation, testing & commissioning of addressable type manual call box of ABS type in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning of addressable type smoke detector with built-in LED and mounting base complete with all connections etc. as required.

CABLING & WIRINGSupplying & laying of 2x1.5 sq mm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.speaker cable Four pair, 2-core, 1.5 sqmm

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Air Conditioning

Supply, testing and commissioning of VRV/VRF Indoor unit equipped with inbuilt microprocessor, synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, etc., suitable for operation on single phase 230 V &p1usmn; 10%,50Hz AC supply, complete, as required-2.0TR 4 way Cassette AC unit

Supply of 1.5 TR Concealed type ductable split AC unit suitable type variable refrigerant flow modular type indoor units with wireless remote compatible to above mentioned outdoor and comprising of all accessories as per the specifications of OEM. The indoor units shall be suitable for operation on 220 &p1usmn;10% volts, 50Hz + 3%, 1 phase AC power supply. The indoor unit shall be complete with pre filter & remote etc as per requirement

Installation, Testing and commissioning of the VRF outdoor units including position to the platform and providing ribbed rubber pad for vibration isolation, fixing, full charge of refrigerant gas, leak testing/pressure testing, giving all power/control/refrigerant connections etc and all required works as per standards etc complete as required at site. (Note- KTDC shall provide a required capacity three phase 4 wire outlet with copper earth within 5m radius of the machine with recommended capacity isolator. Cabling and earthing from the outlet and its termination in machine shall be under the scope of bidder

Installation, Testing and commissioning of the VRF indoor units of all mentioned capacity including fixing above the false ceiling with suitable supports, full charge of refrigerant gas, leak testing/ pressure testing, giving all power/contro1/refrigerant connections etc and all required works as per standards.etc complete as required at site. (Note- KTDC shall provide a required capacity single phase outlet with copper earth within 2m radius of the machine . Necessary wiring and earthing from the outlet and its termination in machine shall be under the scope of bidder )

Supply, Installation, Testing & Commissioning of hard drawn high pressure copper refrigerant piping of OEM recommended size suitable based on the capacity of machines, duly insulated with required thick closed cell elastomeric insulation in tubing form covering with FRP tape and supporting at suitable intervals and required wall opening and restoring the same as good. Entire refrigerant piping work shall be carried out in accordance with the prevailing standards.(No separate measurement will be taken for suction and discharge lines, one unit length measurement measures unit length of both suction and discharge lines)

Supply and Installation of good quality canvas connection

Supply & fixing of 10 mm thick open cell elastomeric nitrile rubber as acoustic insulation of density 140-180kg/m3 with adhesive as per the recommendation of manufacturer,longitudinal & transverse joints sealed with adhesive in neat & clean manner

Supply and installation of aluminium foil faced 9mm thick closed cell elastomeric nitrile rubber thermal insulation of exhibiting class"O" properties with density 45-55kg/m3. on supply air ducts with adhesive as per the recommendation of the manufacturer, longitudinal & transverse joints sealed with adhesive in neat & clean manner

Supply and Laying OEM recommended size control cable between indoor, outdoor and centralized control panel etc through PVC conduit clamped to the wall etc complete as required at site

Supply and Laying 32mm size PVC pipe in position for condensate drain water from indoor unit drain to the floor trap piping with 9mm thick nitrile rubber insulation and with U trap and all other necessary fittings like elbows, tees and reducers, clamping in proper interval etc. complete with required wall openings and making as good as same

Supply of Refnet joints of good qua|1ity and reputed make make