GE/KHU-38/2025-26 SPL REPAIR TO BLDG NO T-6 AND T-9 AT KHUMBATHANG UNDER GE KHUMBATHANG

Amount

Dismantling, wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets.

Taking down cement plaster on brick or concrete wall etc including racking out joints hocking for key scrubbing down with water etc.

Dismantling timber in fillets, rails, posts, rafters, purlins etc under 40 Sq cm in section in any position unframed work complete.

Demolition of brick work or stone/ boulder/PCC block masonry, built in cement mortar including all quoins, pillars etc.complete all as specified

Dismantling of Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling Dismantling wrought iron or mild steel work of any description n complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n exc 15 cm thickness (below or above ground level)

M & L 25 mm thk cement conc. Type B-0 1:2:4 (12.5mm graded crushed stone aggregate) as in sub base to floor complete.

M&L 100 mm thick Cement concrete type D-2 1:4:8 using 40mm graded stone aggregate as in sub base all as specified and directed.

M&L for 75mm thick, cement concrete, type C-2, 1:3:6 (20 mm graded stone aggregate) as in floors & pavings, plinth protection, path, etc. finishing top surface even and Smooth with using extra cement all as specified.

M&L for chequered cement concrete tiles 20cm x 20cm x 20-25mm thick, including 15mm thick screed bed in CM 1:6 set, jointed and pointed in neat cement slurry and filling of joints with grey pigment cement and pigmants in floors complete all as specified and directed.

M&L for .Pre-cast cement concrete block masonry type C-1 1:3:6 (using 16mm graded stone aggregate) with solid blocks exc. 10 cm in width and setting in mortar 1:6 , complete all as specified and directed.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engr-In-Charge

M&L for RCC type B1 1;2;4 using 20mm graded aggregate for Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and inshelves and the like complete all as specified.

M&L for Formwork to soffits/sides of suspended slabs such as roof slabs, floor slabs,beams, landings,chajjas and similar work;(side not exceeding 200mm thick) (Horizontal or sloping)complete all as specified

M&L for18 to 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, platforms and like over and including in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade all as specified.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situation

M&L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. FE 410-W(Gde -E-250) quality A.

M&L for cement concrete in foundation,filling and mass concrete type D2 1:4:8(using 40mm graded aggregate)complete all as specified and directed.

M&L second class soft wood, plain fillets, square or rectangular in section of area exc 13 and n exc 25 Sqcm, clean sawn, secured with nails or brads.

M&L second class soft wood, plain fillets, square or rectangular in section of area exc 6 and n exc 13 Sqcm, clean sawn, secured with nails or brads.

M&L second class soft wood, plain fillets, square or rectangular in section of area n exc 3 Sqcm, clean sawn, secured with nails or brads.

M&L 9mm thick, prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work as in ceiling.

M&L 12 mm thick, prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work as in walls.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

M&L for non skid ceramic tiles 7 to 8 mm thick area of each tiles exc 0.11 sqm but n.exc 0.18 sqm (coloured tiles) in floor, set & jointed in neat cement slurry, pointed,in white or coloured cement to match, over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles coloured (350 x 250 x 7/450x350/300x450x7 to 8mm thick) on walls, set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 10mm thick on fair faces with CM (1:4) complete all as specified and directed.

M&L for Virified Ceramic coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors over and including 15mm thick screed bed in CM 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Dismantling of stone slabs of any description or thickness in floors and approns etc, laid ,bedded and pointed in any mortar all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick over&including 15mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete .

M&L for rendering 10mm thick plaster in cm (1:6\) on fair faces of brick work or concrete surfaces including finishing even & smooth without using extra cement.

M&L for rendering 15mm thick plaster in cm (1:4) on other then fair faces of brick work or concrete surfaces including finishing even & fair without using extra cement.

M&L preparation of newly plastered surfaces and applying two coats of oil bound distemper on surfaces of walls over 1 mm thick wall care putty including preparation of surfaces complete all as specified and as directed by Engineer-In-Charge.

M&L for preparation of New plastered surface and applying two coat Cement base paint on wall complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutter from frame ) n exc 1.50Sqm each.

Taking down chowkats or frame with shutters ( without taking off shutter from frame ) 1.50Sqm and n exc 4.0 Sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but n.exc 2sqm each complete all as specified and directed.

S&F 2nd class HW plain solid straight chowkhats/frame wrought framed rebated on the solid, rounded or chamferred put together with glue pinned at joints complete all as specified and directed.

S&F Flush shutters, 40mm thicksolid core construction, with block board core and plywood face panels, commercial type on both sides all as specified.

Hacking out old broken glass (any thickness size quality or description) from wooden pane glazed with putty or fixed with wooden bends complete all as specified and directed.

S&F 5 mm thick, sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane.

S & F brass barrel tower bolts,stove enamelled black with bright bolt and fixed (150mm length of bolt)

S & F brass sliding door bolts,plate type,stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate and fixed.(250mm length of bolt)

S & F butt hinges heavy weight cold rolled brass and fixed (100mm)

S & F brass handles, (150mm) complete all as specified.

S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L preparing old painted steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified & directed by the Engr-in-Charge.

M&L preparing new or previously untreated iron surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint over a coat of red oxide primer all as specified & directed by the Engr-in-Charge.

S&F in repair 25 mm dia stainless steel curtain rods including end cap/ brackets,stops,rollers latest design etc and taking down old pipe complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down steel tubing and connections 15mm bore of pipe, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down steel tubing and connections 20mm bore of pipe, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix steel water tubing 15 mm bore medium grade galvanized with all fittings such as bends, tees, nipples, elbows, reducers, etc, fixed complete to walls and ceilings or laid in floors all as specified and directed.

All as per item above but 20mm dia

Supply and fix solid PVC door frame of size 50 mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification complete all as specified and as directed by the Engineer-in-Charge

S&F Factory made PVC moulded door shutter with particle board core,28 to 30mm thick(stIles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm prelam colour PVC sheet on back face supplying and fixing in frame at site as per specification and specified by Engr-In-charge

Supply and fix in repair vitreous china ware counter top wash hand basin 410mm x 365 mm x185mm size incl waste fitting as per manufacturers specification complete and making good all connections in repairs complete all as directed by the Engr-in-Charge. Make: Parryware cat part No C0462 or equivalent as spproved by GE

S&F 32mm Dia PVC waste pipe for sinks or wash basines etc,. in repairs complete all as directed by the Engr-in-Charge.

S&F in repair 15 mm bore high neck piller cocks fancy type,cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts. Make : Parryware cat part No T4264A1 or equivalent as approved by GE

S&F repair Bib taps long body cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm dia and fixed Make:Parryware or equivalent as approved by GE

S&F 15mm bore angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair. Make:Parryware or equivalent as approved by GE

Supply and fix PVC connection15 mm bore LDPE pipe 45cm long with brass nuts and washers on both ends all as in repairs specified and directed.

S&F in repairs rim less syphonic vaccume western floor mounted water closet pan (Single piece suit),of size 740x350x660mm white incl seat cover as per manufacturers specification complete all as specified and directed. Make:Parryware cat part No:C8901/C8902 or equivalent as approved by GE

S&F in repair Towel Rack 600mm long 20mm dia,D type cromium plated, fixed with and including Chromium plated brass screws and wooden/plastic cleats. and fixed in repairs all as specified and directed. Make:Parryware cat part No T6008A1 or equivalent as approved by GE

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet galss shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long

S &F 75 mm dia PVC (SWR) floor trap plain with grating doom with or without hole as directed including jointing to waste pipe fixed in solvent cement or cement concrete 1:2:4 type B1 all as specified and directed.

Demolition/Dismantling of drain pipes any type at any position complete all as specified and directed.

S &F 75mm bore PVC(SWR) Pipes single socketed in any length with rubber ring joints laid in trenches or in floor all as specified and directed.

S &F 110mm bore PVC(SWR) Pipes sinle socketed in any length with rubber ring joints laid in trenches or in floor all as specified and directed.

S &F 75mm bore PVC(SWR) bend all as specified and directed.

S &F110mm bore PVC(SWR) bend all as specified and directed.

E/M PART

Taking down carefully copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surface etc.

Material and labour for point wiring with 1.5 sqmm cable FRLS PVC insulated, unsheathed copper multistranded conductor, 1100 V grade of size 1.5 sqmm including necessary termination board 1.5 Sqmm PVC insulated unsheathed FRLS copper conductor as earthing and connected to common earthing with PVC heavy duty casing caping/PVC conduit ISI marked as rquired at site along with all accessories and making good the disturbed surfaces of wall/ ceiling etc for the following : -

One light point/ one fan point/ Bell Point controlled by one switch

One 3 pin socket outlet, 5 Amp independent

Supply switch piano flush type single pole one way 5 Amps all as specified

Supply switch socket combination multi purpose, 5 amp all as specified

S & Fin repair Ceiling rose 3 plates flush type 6 Amps,250 volts AC ISI marked

All as per item No 2 above but for point wiring for power point with 2.5 Sqmm FRLS PVC insulated unsheathed copper cable 1100 Volt grade drawn through and including PVC casing caping heavy duty ISI marked /heavy duty conduit ISI marked as required at site alongwith accessories with 2.5 Sq mm FRLS PVC insulated unsheathed copper conductor cable as earthing and connected to common earth all as specified.

S & F switch socket combination switch socket outlet 3 pin, 16 amp flush type

S&F wall mounted LED light fitting 1x20 watts AC decorative box type with driver holder including LED tube light , energy efficient type 4 feet long including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose.

Supply and fix sheet metal enclosure SPN DB 02 way,single phase 240 volts double door with 200 amp rated bus bar complete all as directed.

S&F LED security light fitting 35 watts 230 volts AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F LED luminaire 600mmx600mm 35/36 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver , holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete

S & F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified.

S&F sheet metal enclosures distribution boards,double door 4 way three phase 415 volts MCCB,ISOLATOR&MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a) MCCB 4 Pole 100 AMPS AC 415 V 10 KA=01 NO as incoming & outgoing MCB SP-12 No 40 AMP (Note :- (i)The DB shall be of VTPN series (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(1v) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly.

Supply and fix sheet metal enclosure SPN DB 08 way,single phase 240 volts double door with 200 amp rated bus bar complete all as directed.

Supply and fix for Circuit breaker single pole, 5 to 32 Amp 240 volt C curve 10 KA, IP 20 complete all as specified and directed incl taking down old one.

M&L for Circuit breaker single pole & neutral 240 volt C curve 10 KA 40 to 63 Amps capacity IP 20 complete all as specified and directed incl taking down old one.

Suply and fix envirnmental friendly aesthetically designed ,decorative New Innova LED Neo swivel Focus light 6 W. Aesthetically designed lens based accent light 6000 K for crisp light output. for low ceiling height application. (Make :- Havells/ Bajaj/CG)

Supply and fix Bed Side Light LED 3 Watt complete all as specified and directed. Make : Philips/ CG/ Havells

Supply and fix decorative fancy Wall Light LED 9 Watt complete all as specified and directed. Make : Philips/ CG/ Havells

S&F two single core 2.5 sqmm for sub Main wiring with copper conductor multistranded PVC insulated and unsheathed 1100 Volts grade in and including PVC casing capping with fixing accessories including one run of 2.5 Sq mm copper conductor. (Note - Two runs of 2.5 Sq mm cable, one run of 2.5 Sq mm earth cable and one run of PVC casing Capping shall be measured as one running meter.)

S&F two single core 6.0 sq mm for Sub Main wiring with copper conductor multistranded PVC insulated and unsheathed 1100 Volts grade in and including PVC casing capping/ pvc conduit with fixing accessories including one run of 6 Sq mm copper conductor. (Note - Two runs of 6 Sq mm cable, one run of 6 Sq mm earth cable and one run of PVC casing Capping shall be measured as one running meter.)

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth and getting it out for laying of cable / pole etc in hard/dense soil all as specified.

Returning, filling in, including spreading, leveling watering, and well ramming in layers not exc 25 cm in hard/dense soil all as directed.

Removing excavated material n.exc 50m and depositing where directed at a level exc. 1.5 cm above the starting point all as directed.

M&L for stone dust sand cushioning to UG cable laid in trenches all as specified and directed.

Supplying and laying unreinforced precast concrete cable cover, class HV, type 1 flat of size 250mm x150mm x 40mm placed perpendicular of the cable complete.

Supply laying and testing cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables heavy duty 1100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core.

Supply laying and testing cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables heavy duty 1100 volts grade with stranded aluminium conductor of size 16 sqmm 2.0 core.

Material and labour earthing complete with galvanized steel earth plate 60 cm x 60cm x 6.0mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less less than 1.5 mtr filled around with 15 cm thick alternate layers of charcoal dust and salt and connected to earth lead wire 4mm dia (8 SWG) by means of bolt, nut and check nuts and washers of galvanized iron or steel and thimble and other ends of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm bore and watering pipe 20mm dia light grade with funnel and wire mesh, pcc 1:3:6 type C-1 in chambers RCC 1:2:4 type B-1 in pit cover reinforced with 8 mm dia deformed bars 15cm center to center both ways all as directed by Engr-In-Charge, complete all as shown in electric plate No 3 of MES SSR Part I

Dedcuct Credit for Demolished/Dismantled material Rs (-) 41171.00 (Minus) as listed in Schedule 'A' Sec-II (Credit Schedule) Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'.

KASHMIR FAIR DEAL SERVICES (BID ID -3318107)

M/S TRADE LINK (BID ID -3315814)

M/S Haji Hadi (BID ID -3319276)