GE AF/AMB-73/2021-22 IMPROVEMENT OF CERTAIN SERVANT QUARTERS OF OMQS AT RACE COURSE AREA AT AF STATION AMBALA

Amount

M&L for cutting bushes / plants on building surfaces upto roots and applying chemical glycphosate to stop further growth of the plant, etc. and grouting and filling the holes in CM 1:4 including all necessary T&P and disposing off the rubbish to a distance not exceedng 50m complete all as specified and as directed

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles and disposing off complete all as specified and as directed

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal of debris complete all as specified and as directed

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for keys, scubbing down with water, etc. including all necessary scaffolding as required and rubbishing off the premises, etc. complete all as specified and as directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and disposing off complete all as specified and as directed

Taking up or down 15mm bore steel water tubing and connections including disposing off, etc. complete all as specified and as directed

Taking up or down 20mm bore steel water tubing and connections including disposing off, etc. complete all as specified and as directed

Demolition of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part thereof) complete all as specified and as directed

Dismantling brick tiles or terracing tiles, single layer on roofs, sorting and stacking serviceable tiles and disposing off unserviceable tiles complete all as specified and as directed

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in cover slabs, removing debris from site and making good the disturbed surfaces / portions in existing specifications complete all as specified and as directed

Taking down chowkats or frames not exceeding 1.5sqm each with shutters (without taking off shutters from the frame) and disposing off

Taking down chowkats or frames exceeding 1.5sqm but not exceeding 4sqm each but with shutters (without taking off shutters from the frame) and disposing off

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) 75/100mm bore (internal dia) set in cement mortar and disposing off complete all as specified and as directed

M&L for 75mm thick plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate as in floors, plinth protection, pavings, etc. including making spike rolling to surfaces or making impressions of expanded metal whilst the concrete is green laid in alternate bays of 3m length and joints between bays filled with sealing compound grade-A complete all as specified and as directed

M&L for plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in coping, drain channels, golas, etc. complete all as specified and as directed

M&L for plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregates) as in padding to make good depressions, etc. complete all as specified and as directed

M&L for RCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in balcony, shelves, parapets, railing, chajjas, etc. and similar works over 1.5m span complete all as specified and as directed

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges for rought finished surfaces of concrete complete all as specified and as directed

M&L for brickwork with sub-class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:4) complete all as specified and as directed

M&L for brickwork with sub-class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed

M&L for mild steel TMT bars grade Fe-500D, 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L for MS framed works as in doors or gates of angle or other section with gusset plates, rails, braces, etc. drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-410-W grade E-250 quality-A complete all as specified and as directed

M&L for non-skid ceramic tiles, coloured, area of tile exceeding 0.11sqm but not exceeding 0.18sqm each, 7 to 8mm thick of superior quality in floors etc laid over 15mm thick screed bed in CM (1:6) (rate shall be included) set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match shade of tiles complete all as specified and as directed

M&L for coloured glazed designer ceramic tiles, of size 350x450mm x 6 to 7mm thick of superior quality fixed on vertical surfaces such as skirting / dado / risers of step, etc., fixed over backing coat of 10mm thick plaster in CM (1:4) (rate shall be included) set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles all as specified and as directed

M&L for rendering 15mm thick in cement mortar (1:4) on fair surfaces of PCC block / brick masonry wall / concrete surfaces, etc. finished fair and even without using extra cement complete all as specified and as directed

M&L for rendering 15mm thick in cement mortar (1:6) on fair surfaces of PCC block / brick masonry wall / concrete surfaces, etc. finished fair and even without using extra cement complete all as specified and as directed

M&L for rendering 15mm thick in cement mortar (1:4) on other side of lathing as in roofs finished even and smooth without using extra cement complete all as specified and as directed

M&L for rendering 5mm thick plaster, in cement mortar (1:3) on fair faces of concrete surfaces of soffits of slabs, ceilings, etc. finished even and smooth without using extra cement complete all as specified and as directed

S&F steel water tubing, 15mm bore, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for protection of electric clables complete all as specified and as directed

S&F steel water tubing, 20mm bore, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for protection of electric clables complete all as specified and as directed

S&F in repairs 20mm dia ball brass valves, high pressure, with polythene float and flynut, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed

S&F 20mm dia ball brass valves, high pressure, with polythene float and flynut, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed

S&F factory fabricated flush shutters, 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc and divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, sizes of members of shutters as specified in clause 8.20 9(b) of SSR Part-I, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., supplied and fitted to chowkats complete all as specified and as directed

S&F solid PVC door frame of size 50x47mm made out of 5mm thick plain / printed coloured PVC sheet (as approved) reinforced with MS square tube all as per specifications and drawing given in SSR Part-I 2009 all as per manufacturer's instructions and making good the disturbed surfaces complete all as specified and as directed

S&F factory made solid PVC moulded door shutter (with wood free EPS), 28 to 30mm thick (styles), with 2, 4, 6 raised panel design with 2mm thick moulded PVC sheet on the front and 2mm thick coloured PVC sheet (tint as approved) on back faces and fixing in frame at site all as shown in and specified in MES Schedule 2020 & 2009 complete all as specified and as directed

S&F steel window (box type) factory fabricated, double shutter (glazed and wire gauzed) with side hung shutters including pintle type hinges, steel handles fabricated type for each leaf duly welded, mild steel barrel tower bolts 150mm size (02Nos for each leaf) duly welded, with glazing bars dovetailed or welded including MS fillets, welding of guard bars with one shop coat of red oxide zinc chrome primer overall complete all as specified and as directed Notes: (i) Windows shall be fabricated as per CE Palam drawing No. TD-219 Sh 1/3 to 3/3 dated 02 Jan 2007 (updated up to date) and these drawings shall be referred at the O/o the GE (AF) Ambala (ii) Glazing, wire gauge, guard bars will be measured and paid separately under respective items herein (iii) Any other sundries, etc. as required at site shall be deemed to be included in the quoted rate (iv) For measurement purpose only area of opening shall be measured

S&F in repairs 20mm dia fancy type powder coated (tint as approved) mild steel of wall thickness 1mm (min) curtain rods / towel rails, etc. fixed with and including 2Nos. suitable powder coated brackets, holders with funnel at ends complete all as specified and as directed

S&F 100mm butt hinges, type B-21 of extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and as directed

S&F 300mm, MS ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed

S&F in repairs 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed

S&F in repairs aluminium alloy, anodised, sliding door bolt with hasp, length of bolt 250mm, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed

S&F in repairs 150mm long, extruded aluminium door handles, fabricated type with back plate 3mm thick, complete all as specified and as directed

S&F 3mm thick figured / pin headed glass, ordinary quality, area not exceeding 0.5sqm in each pane, cut to required size and shape to existing wooden shutters / MS windows / shutters, etc. with glazing clips, glass oil putty, etc including hacking out old broken glass (any thickness), cleaning hacked grooves, removing damaged putty, beads, etc complete all as specified and as directed

S&F 3mm thick sheet glass, ordinary quality, area not exceeding 0.5sqm in each pane, cut to required size and shape to existing wooden shutters / MS windows / shutters, etc. with glazing clips, glass oil putty, etc including hacking out old broken glass (any thickness), cleaning hacked grooves, removing damaged putty, beads, etc complete all as specified and as directed

S&F in repairs galvanised mild steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified and as directed

M&L for preparing of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint (tint as approved) over a coat of red oxide zinc chrome primer complete all as specified and as directed

M&L for preparing of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint (tint as approved) complete all as specified and as directed

M&L for preparing of new steel surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint (tint as approved) complete all as specified and as directed

M&L for preparing of new wood / wood based surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, tint as approved complete all as specified and as directed

M&L for preparing of new wood / wood based surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint, tint as approved complete all as specified and as directed

M&L for preparation of new masonry / concrete wall surfaces and applying two coats of oil emulsion distemper over a coat of wall primer including a coat of wall care putty 1mm thick including all necessary staging, etc. as required to work at heights, etc. complete all as specified and as directed

M&L for preparation of old masonry / concrete treated / untreated wall surfaces by scrapping with wire brush moulds, soot, efflorescence, grease, etc. removing nails, etc. and applying two coats of oil emulsion distemper over a coat of wall care putty 3mm thick including all necessary staging, etc. as required to work at heights, etc. complete all as specified and as directed

M&L preparation of new plastered / unplastered surfaces and applying two coats of white wash on ceilings, soffits, etc. complete all as specified and as directed

M&L preparation of old plastered / unplastered, treated / untreated surfaces and applying two coats of white wash on ceilings, soffits, etc. complete all as specified and as directed

M&L for preparing of new plastered or unplastered surfaces of walls and applying two coats of cement based paint (of approved tint) over a coat of alkali resistant wall primer complete all as specified and as directed

M&L preparation of old plastered / unplastered masonry / concrete surfaces of walls by scrapping old treatment, sooth, moss, grease, etc. brooming and washing clean and applying one coat of cement based paint complete all as specified and as directed

Supplying, hoisting, fixing and connecting up rotational moulded polythylene water storage tanks (cylindrical vertical with closed top), 500litres capacity, hoisted and fixed in position all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes, tank nipple, elbow, bend, unions, sockets, etc. complete all as specified and as directed

S&F in repairs 15mm dia bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed

S&F in repairs 15mm dia stop cocks / angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, fancy type, screwed both ends for iron pipe or for unions or for brass ferrule complete all as specified and as directed

S&F 15mm dia pillar taps, fancy type, cast copper alloy, with capstain heads, chromium plated, screwed down, high pressure, with or without lettered 'HOT'/'COLD', with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed

S&F in repairs 15mm PVC connections, 450mm long with brass couplings, PTMT nuts, etc. complete all as specified and as directed

S&F in repairs vitreous China squatting pan, Orissa pattern of size 580x440mm, white, with integral foot rests and 'P' or 'S' trap, connecting to flushing pipe and trap and making good to the disturbed surfaces in CM 1:3 with finishes to match with the existing complete all as specified and as directed

S&F in repairs wash hand basin, vitreous China, coloured, flat back type, of size 640x450mm, including CI brackets, cutting for and pinning in ends of brackets with coupling and including PVC connection 60cm key with brass union complete all as specified and as directed

S&F 10litres capacity PVC flushing tank, white / coloured, syphonic action type, low level, valveless, with PVC inlet ball valve, PVC flush pipe, float and suitable sized brackets including cutting of floor / wall and making good to the disturbed surfaces in CM 1:3 with finishes to match with the existing and taking down of old PVC flush tank and disposing off complete all as specified and as directed

S&F in repairs sink with drainage board overall size 915mmx460mm and bowl size 410x330x160mm, made of stainless steel 1mm thick for kitchen with plugs, washer and waste including in cement mortar to dwarf wall or including fixing cantilever brackets and connection union to pipe complete all as specified and as directed

S&F in repairs PVC (SWR) pipes, 110mm bore, single socketed in any length with rubber ring joints fixed on walls with suitable clamps, etc. complete all as specified and as directed

S&F in repairs PVC (SWR) pipes, 110mm bore, single socketed in any length with rubber ring joints laid in trenches / floors complete all as specified and as directed

S&F in repairs PVC (SWR) pipes, 75mm bore, single socketed in any length with rubber ring joints fixed on walls with suitable clamps, complete all as specified and as directed

S&F in repairs PVC (SWR) pipes, 75mm bore, single socketed in any length with rubber ring joints laid in trenches / floors complete all as specified and as directed

S&F in repairs PVC (SWR) bends any radius for 110mm bore pipe with oval access door complete all as specified and as directed

S&F in repairs PVC (SWR) bends any radius for 75mm bore pipe with oval access door complete all as specified and as directed

S&F in repairs 100mm dia mild steel chromium plated grating doom fixed on floor trap / nahani trap and fixing / jointing in CM 1:6 complete all as specified and as directed

M&L for Atactic Poly Propaneylene (APP) modified bituminous membrane, 3mm thick, weight not less than 3.6kg/sqm, reinforced with non-woven polyester fibre @160gm/sqm by torch method as per manufacturer's instructions complete all as specified and as directed Specifications for membrane: (i) Softening point 150oC minimum (ii) Cold flexibility (-)2oC minimum (iii) Single centre core non-woven polyester reinforcement of not less than 160gm/sqm (iv) Tensile strength of 650N/sqcm and 450N/sqcm in longitudinal and transverse directions respectively (v) Minimum elongation of >20% in both directions (vi) Dimensional stability of 1% maximum (vii) Water tightness / impermiable at 2kgf/sqcm (viii) Water absorption of not more than 1% on mass within 24hrs (ix) Overlaps of minimum 100mm on longitudinal direction and 150mm along transverse direction shall be maintained while laying

M&L for 40mm thick brick tiles laid over and including 15mm thick cement mortar screed in 1:6, jointed and grouted flush in cement mortar 1:3 in roofs complete all as specified and as directed

--ditto-- all as per serial item No. 76 hereinabove but except tiles complete all as specified and as directed Note: Serviceable brick /terracing tiles obtained under taking down hereinabove shall be reused in this item

Swami Enterprises

peeyush construction and engineering co