CA NO GE(N)AMB-26/2021-22 REPAIR TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING AND OTHER CONNECTED BLDG REPAIR WORKS IN JCO/OR MD-II ACCN OF AGE B/R-I OF GE (NORTH) AMBALA CANTT

Amount

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

M & L cutting chases ,pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the Engineer-in-Charge.

Supply & fixing pillar tap 15mm bore, cast copper alloy with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connections & flush pipes for WC as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern) including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC pipe and complete accessories as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing plastic water closet seat cover , white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 20mm bore cast copper alloy chromium plated stop valves , screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy angular type chromium plated stop valves with long shank and cup, screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy chromium plated bib tap fancy type long body, with butterfly handle screwed down, screwed for iron pipe or for brass ferrule as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minimum weight-210 gms) as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F 125 mm dia brass chromium plated shower rose swivel type with arms of standard length as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges as in repair complete all as specified and as directed by the Engineer-in-Charge

S & F as in repair 15mm bore cast copper alloy chromium plated stop valves, screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing grating doom 100 mm dia of PTMT (minimum weight 25 gms) as in repair complete all as specified and directed by Engineer-in-Charge.

S & F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F 15mm bore cast copper alloy chromium plated stop valves fancy type with long shank and cup (concealed type) screwed down, high pressure with butter fly handle scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

M & L for taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by the Engineer-in-Charge

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls etc complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls etc complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) bends of any radius diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC(SWR) bends of any radius, for 110mm bore pipes, with access doors, complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm bore PVC (SWR) branch pieces double (double Y) equal are unequal with access door complete all as specified and as directed by the Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed by the Engineer-in-Charge.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair jet spray brass chromium plated with flexible pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F 32 mm dia PVC waste pipe of standard length for wash hand basin / Kitchen sink etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

M & L taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 15mm thick in cement plaster 1:6 on any faces of brick work or concrete wall surfaces and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in charge.

M&L rendering 15mm thick in cement plaster 1:4 on any faces of brick work or concrete wall surfaces and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in charge.

M&L rendering 10 mm thick on fair faces of brick work or concrete ceiling or chajjas surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M & L preparing new plastered surfaces of wall and applying two coats of oil emulsion distemper with painting roller over a coat of primer over and including 2 to 3mm thick wall care putty white cement based in two or more coats to achieve smooth surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered surfaces of wall and applying two coats of cement based paint complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered/ unplastered surfaces of celing and applying three coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated plastered/ unplastered surfaces of celing and applying one coat of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

M & L preparing old decorated plastered surfaces of wall and applying two coats of oil emulsion distemper with painting roller over a coat of primer over and including 2 to 3mm thick wall care putty white cement based in two or more coats to achieve smooth surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated plastered/ unplastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

M&L rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated plastered/ unplastered surfaces of wall and applying/finishing walls with acrylic smooth exterior paint of required shade (two or more coats applied @ 1.67 ltr/10 sqm complete all as specified and as directed by the Engineer-in-Charge.

Resecuing without taking down chowkats or frames with shutters of any description area exc 1.5 sqm and not exc 4.00 sqm each and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge

S&F 150 mm long aluminium handle cast type anodised as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair butt hinges 100 mm long medium weight stainless steel and fixed complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

M & L sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge

S & F as in repair 100mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by the Engineer-in-Charge

M & L figured glass 3.0mm thick pin head type and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge

S&F as in repair galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair mild steel 150 mm ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area not exc 1.00 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc 1.5 sqm but not exc 4 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

M&L factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

M&L factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

S&F galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

M&L prepration of new wooden surface and apply two coats of synthetic enamel paint over a coat of pink primer on surface of any description , not otherwise described over 10cm width or girth complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair mild steel powder coated decorative finish curtain rod 20mm dia having wall thickness 1.60mm fixed with and including decorative brackets ,stop roller and glass at the end etc complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs, guard bars and painting etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 and TD-220 sheet 1/3 to 3/3 as applicable complete all as specified and as directed by Engineer in Charge. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill fabricated from 10mm square MS bar as shown on drgs. (iii) Glazing, wire mesh shall be measured and paid for separately.

S & F steel windows or ventilators, fixed type, with glazing bars including two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

M&L rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-410-W (Gde E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet ( all as per Godraj Pettern) with three way locking arrangement with brass lock with CP handle with duplicate key including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard fixed with necessary nuts, bolts and washers including embedded in PCC 1:2:4 (area of opening shall be measured) complete all as specified and as directed by the Engineer-in-Charge.

M&L 2nd class hard wood small fitting such a brackets of any type ,latch and hinge block , shaped door and window stops and the like including all necessary labours articles n. exc200 Cu cm each complete all as specified and as directed by the Engineer-in-Charge.

S & F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 290 Gde-E-165 complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new steel surface and applying two coats of synthetic enamel ordinary tint paint over a coat of red oxide primer on steel or iron surfaces of any description over 10cm in width or grith, not otherwise described complete all as specified and as directed by the Engineer-in-Charge.

S & F 100mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by the Engineer-in-Charge

M & L cutting into existing manholes for connecting new drain, making good to pipe 150 mm dia and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and as directed by the Engineer-in-Charge.

M & L for running welding in repairs, thickness of metal to be welded not exc 6mm, complete all as specified and as directed by the Engineer-in-Charge

S & F as in repair brass chromium plated hand health faucet with PVC pipe of standard length complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) of any description and in any position complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of existing sunken treatment PCC any thickness(below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

M & L 40mm dia (bore) GI Pipe, medium grade as in spout complete all as specified as directed by the Engineer-in-Charge.

M&L PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate as in filling in sunken floor, rounded or chamfered on edges complete all as specified.as directed by the Engineer-in-Charge.

M&L providing sunken floor water proofing treatment comprising of the following :- (a) Scrapping the surface with wire brush and cleaning with water and allow to dry. (b) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufactuers instructions. (c) 15 mm thick cement plaster in cement mortar 1:3 mixed with water proofing compound @ 2% by weight of cement or as per manufacturer instruction ( the corners will be made round in concave shape) and finished even and fair without using extra cement. (d) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufacturer instruction. (e) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm (f) Providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt using butane gas torch and sealing all joints. (g) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm.

M & L plain cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork for rough finished surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

M & L 25mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base, finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M &L 10mm thick coloured paver tiles (Endura Tiles) of size 300 x 300mm in floors etc set and jointed in neat cment slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in C.M 1 :4 ,complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

M&L Non-skid ceramic coloured tiles joint free 1st quality (square/rectangular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L glazed ceramic coloured tiles joint free 1st quality 7mm thick in vertical surfaces/skirtings/dados of size 450x350 mm or nearest size as required at site , set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L Non-skid ceramic coloured tiles joint free 1st quality (square/rectangular) 9 to 10 mm thick, area of each tile exc 0.18 sqm but not exc 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L Non-skid ceramic coloured tiles joint free 1st quality (square/rectangular) 9 to 10 mm thick, cut from area of each tile exc 0.18 sqm but not exc 0.36 sqm as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

S & F 150mm aluminium handles, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge.

S & F 150mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F stainless steel butt hinges 100 mm long medium weight complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 300 mm long aluminium alloy anodised sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section to door shutter complete all as specified and as directed by the Engineer-in-Charge.

M&L 18 mm thick prelaminated particale board, exterier grade (grade-1) confirming IS 14587, fixed with nails for kitchen cupboard and cabinet ,shelves for cupboard , frame with door if required including 3mm thick 2nd class hardwood leeping patti on cut edge of boards as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair kitchen plate rack of stainless steel sheet 1mm thickness size 900mm x 900mm x250mm and having weight not less than 8.00 Kg each complete all as specified and as directed by the Engineer-in-Charge.

S & F sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes; in-cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair complete all as specified and as directed by the Engineer-in-Charge

S & F as in repair waste coupling fittings 32mm dia of brass, chromium plated for glazed ware sink, basins etc. with long screwed shanks and fly nuts flange end bedded in red lead cement complete all as specified and as directed by the Engineer-in-Charge.

Cleaning of sewage line upto first man holes by any means and removing blockage of WC, EWC, Bathroom, floor trap of WHB/Kitchen pipe etc complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 250 ltr and not exc. 500 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 500 ltr and not exc. 1000 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

M & L 500 Litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight 210gms) complete all as specified and as directed by the Engineer-in-Charge. Note:- Tank shall be in white colour.

M & L 1000 Litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight 210gms) complete all as specified and as directed by the Engineer-in-Charge. Note:- Tank shall be in white colour.

M&L TMT mild steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

M & L providing PCC precast 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, precast cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weathering, throating etc and setting CM 1:4 complete with joints to match, complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Disconnecting existing tanks exceeding 250 ltr and not exceeding 500ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and as directed by the Engineer-in-Charge.

M&L cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity exc 250 litre and not exceeding 500 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- unit rate shall be included to make small fittings such as elbow, socket, reducer, tee, union etc complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of plain or corrugated asbestos cement sheet of any thickness incl Nainital or similar pattern coverings, complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having zinc coating 150 gm per Sqm (Az 150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150gm/Sqm (Az-150) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

S & F rubber strips 3 to 4 mm thick and 65 to 75 mm wide on bottom rail of door for covering gaps between door and floor to avoid entry of insects, dust etc and fixed with screws complete all as specified and as directed by the Engineer-in-Charge.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and removing the same to a distance exceeding 250mtr but not exceeding 500mtr, deposited where directed including cleaning the surfaces complete all as specified and as directed by the Engineer-in-Charge.

M & L preparing roof surfaces and applying water proofing treatment comprising of the following:- (a) Plastering 20 mm thick in cement mortar 1:4 using 100% coarse sand on roof including WPC @ 3% by weight of cement or as per manufacturer's instructions. (b) Applying a coat of bitumen primer conforming to IS-3384-1965oil bound bitumineous primer at the rate of 0.50 Liters/Sqm as per IS 3384-1986 on prepared surfaces. (c) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm (d) Providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt using butane gas torch and ceiling all joints with 100mm side lap & 150mm end lap. (e) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm. (f) Applying one coat of bitumineous aluminium paint @ 150grm per sqm. NOTE: The membrane shall be extended and inserted into the groove of size 50mm wide and 75mm deep, cut in to the parapet wall and sealed with cement plaster (1:3) mixed with WPC @ 3% by weight of cement and the cost of same is deemed to be included in the quoted rate.

Supply and fixing 300 mm long aluminium alloy anodised sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section to door shutter as in repair complete all as specified and as directed by the Engineer-in-Charge.

shiv const co

Sawhney Constructions

M/S SHANTI CONSTRUCTION

MAYANK ENTERPRISES

Karishan Kumar goel

M/s Kuljit singh bedi