ADDITION / ALTERATION OFJCOs AND OR MD ACCN AT MISSAMARI

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering and ridge complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridge complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and as directed.

S & F anodised aluminium snap grid frame work of size 605 mm x 605 mm for false ceiling including 4mm thick non-asbestos (E-board) fibre cement building board fixed to aluminium frame work with screws and applying two coats of oil bound distemper on one side of the board complete all as specified and driected.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top including taking down existing treatment complete all as specified and directed. (i) Screed bed or bedding layer 15 mm thick in CM 1:4 as in roof Slab including preparation of surface to receive screed bed. (ii) Applying one coat of cold bituminous primer 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces. (iii) APP based polymeric membrane 3mm thick, minimum weighing 3.5 Kg/sqm, reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied over bituminous primer as specified above by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction and sealing the joints with application of cold bitumen. (iv) Applying two coats of aluminum paint over the APP membrance .

Taking up or down GI tubing 15mm dia and fittings etc complete all as specified and directed.

Taking up or down GI tubing 20 dia and fittings etc complete all as specified and directed.

S&F GI tubing 15mm dia, medium grade with all fittings fixed complete to walls and ceiling or laid in floor complete all as specified and directed.

Fixing only 15mm GI tubes any grade, to walls and ceilings or laid in floors including fittings and making good the disturbed surface complete all as specified and directed. (Note: Old serviceable GI pipe shall be obtained from item No. 8, here-in-above)

S&F GI tubing 20mm, dia medium grade with all fittings fixed complete to walls, ceiling or laid in floor complete all as specified and directed.

Fixing only 20 mm GI tubes any grade, to walls and ceilings or laid in floors inlcuding fittings and making good the disturbed surface complete all as specified and directed. Note: Old serviceable GI pipe shall be obtained from item No. 9, here-in-above)

S & F in repair 15mm, bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S & F 15mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs, CP bib tap 15 mm bore, fancy type, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed.

S & F 15mm bore stop valve/Angular stop cock cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S & F in repair 15mm bore, stop valve/Angular stop cock, cast copper alloy fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F 20mm dia brass chromium plated tubular towel rail, D type, 60 cm long, fixed with bracket complete all as specified and directed.

S & F brass chromium plated shower rose, 125 mm, with or without swived joints any size including fixing to steel pipe or union complete all as specified and directed.

S&F brass chromium plated, Wall mixer 3 in 1, for mixing hot and cold water screwed down for iron pipe and fixed with connections with and including L bend for shower provision complete all as specified and directed.

S&F in repair stainless steel Grating doom, 100mm dia complete all as specified and directed.

S & F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks tripple layer (white) 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including wash out GI pipe 32mm of 450mm length with stopper complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160mm complete all as specified and directed.

S&F in repair kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160mm complete all as specified and directed.

S&F kitchen plate rack made of stainless steel sheet not less than 0.63mm thick of over all size 1050x750x250mm complete all as specified and as directed.

S & F in repair PVC valve less, syphonic action type, flushing cistern of capacity 10 litres, low level white with inlet, ball valve, float and handle including brackets and connection to pipes complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) 110mm dia junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repairs PVC (SWR) bend of any radius 110mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) bend of any radius 75 mm bore complete all as specified and directed.

S&F in repair 20mm dia Ball valve, high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms) complete all as specified and directed.

S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repair Harrison rails, mild steel, chromium plated with fixing brackets with knob, stops, rollers etc complete all as specified and directed.

S& F in repair Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, brass CP waste coupling 32mm dia, PVC flexible waste pipe and PVC connection 15mm size 600mm length with PTMT nuts,, including dispose off the broken WHB out of the premises complete all as specified and directed.

S&F Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, brass CP waste coupling 32mm dia, PVC flexible waste pipe and PVC connection 15mm size 600mm length with PTMT nuts complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

M&L in repair Vitreous china squatting pan of Orissa Pattern of size 580x440mm white integral foot rests and PVC 'P' or 'S' trap, fron or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC, and finishing the top surfaces to match with the existing flooring including dispose off old broken WC out of the premises complete all as specified and directed.

S & F in repair Wash down water closet pan (pedestal pattern), vitreous china, white, including PVC 'P' trap, seat cover, connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc, including dispose off the old broken WC out of the premises complete all as specified and directed.

S & F Bathroom Cabinet of hard thermosetting polymer of size 350x450 mm, fitted with superior quality distortion free, 4 mm thick mirror, complete all as specified and as directed.

Taking down chowkats or frame with shutter without taking off shutter from the frame, exc 1.50 sqm but not exc 4 sqm each & removing from site of work complete all as specified and directed.

Taking down chowkats or frame with shutter without taking off shutter from the frame not exc 1.50 sqm & removing from site of work complete all as specified and directed.

Taking down shutter exc 1 sqm but not exc 2 Sqm each complete all as specified and directed.

S & F 105x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S&F powder coated aluminium anodised frame (of size 44mmX34mm) for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc, complete all as specified and directed.

S&F powder coated aluminium anodised window/ventilator shutters side hung type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised powder coated aluminium snap beading, screws,75 mm long aluminium butt hinges-03 Nos on each shutter, hold fast, pegstays, handles etc complete all as specified and directed. (Note :- (i) Fixing of shutter with all powder coated fittings shall be as per manufactures instructions. (ii) Rate quoted is deemed to be inclusive of aluminium hardware as indicated, glazing clips, rubber packing, hinges, anodised aluminium snap on beading for fixing glass panes in frame, handles, locking arrangement but glass panes in frame shall be measured and paid seperately under respective Sch 'A' items.)

S & F 30mm thick, factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F 30 mm thick, 2nd class hard wood, glazed and skelton shutter open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified & directed.

S & F 2nd class HW, plain fillets, square, rectangular or triangular in section exc 13 Sqcm not exc 25 sq cm, clean swan, secured with nails or brads complete all as specified and directed.

S & F 25 mm thick factory made Flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F factory made, solid PVC door frame of size 50mm x 47mm, made out of 5mm plain colour PVC sheet, reinforced with MS square tube complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes all around . M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,complete all as specified and directed.

S & F 100mm size butt hinges cold rolled mild steel medium weight, ISI marked complete all as specified and directed.

S & F 150 mm size Aluminium anodised handles cast type,ISI marked complete all as specified and directed.

S&F 150mm long aluminium, anodized, barrel tower bolts of extruded section ISI marked complete all as specified and as directed.

S & F 250mm long Aluminium alloy, anodised sliding door bolt, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed with stainless steel wire staples complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded agg) as in plinth protection and finishing the surface even & smooth without using extra cement including joint filling with the bitumens filler bitumen complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out, in hard / dense soil complete all as specified and directed.

Removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M & L for hardcore of broken stone or boulders, gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified and directed.

M & L for 100mm thick PCC 1:2:4 type B-1, (using 20mm graded crushed stone aggregate) as in floor/hardstanding, finishing the surface even and smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. Note : All internal door shall be removed before fixing of tile and shall be re-fixing after completion to tiling work. (Taking down and refixing of door in its original position shall be measured and paid separately)

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed. Note : All internal door shall be removed before fixing of tile and shall be refixed after completion of tiling work.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.

M&L for Glazed ceramic colour tiles of size 450x350x 7mm / 350 x 250 x 7mm thick in vertical surface of wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete all as specified and directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.

All as per Item No.72 above but 600mm x 150mm as in skirting etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete all as specified and directed.

M&L for Marble of green shade or other than white and black, 18 to 20mm thick (table rubbed and polished) in steps, bathroom self, corner (including necessary cutting chasing) jambs,pillars, window cills, cocking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed

M & L for Machine cut kota stone slab flooring, 18-20 mm thick over 20 mm thick cement screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for Machine cut kota stone slab, 18-20 mm thick as in riser of steps, skirting, dado etc laid over 15 mm thick screed bed in CM 1:6 as jointed with grey cement slurry mixed with pigment to match the shade including rubbing & polishing complete all as specified and directed.

M & L for sunken floor treatment by roughning of sides and bottom of sunken floor by picking, sweeping clean and washing down with water to remove dust etc and 10 mm thick rendering in CM (1:4) on concrete surface(bottom sides of sunken floor) finished fair and even mixed with liquid water proofing compound conplast x 421IC mfd by M/S FOSROC chemicals India pvt ltd, priming coat of Nitro proof 100 and after drying of primer applied one coat of Nitro proof 120 mfd by M/S FOSROC chemicals India pvt ltd complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4, complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins arches pillars etc complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc. 6 mtr mean radius, built in CM(1:6), complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as directed

M & L for RCC 1:5:3 type A-1,(using 20mm graded crushed stone aggregate) as in slab supported on walls, beam and column in floors , roofs, landing deck slab etc complete all as specified and directed.

M & L for use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, for fair finished surfaces not exceeding 200mm thick complete all as specified and directed.

M&L for TMT Bars, 10 mm dia & over, cut to length, bent to shape required, including cranking, binding spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key scrubbing down with water etc including removal of rubbish material from the premises complete all as specified and directed..

M&L for rendering 20mm thick plaster in two layer in CM 1:4 mixed with water liquid proofing compound on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid separately.)

M&L for 15 mm thick plaster in CM 1:6 other than fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick plaster in CM 1:3 on fair faces of concrete surfaces of ceiling including finishing even & smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion complete all as specified and directed.

M&L for three coats of white wash on newly plastered surface of ceiling including necessary preparation of surfaces complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of ceiling including cornices, pilasters etc and applying one coat of white wash complete all as specified and directed.

M& L for complete removal of existing treatment by scrapping, wire brushing from walls and applying two coats of oil bound distemper including preparation of surfaces complete all as specified and directed.

M&L for applying a coat of 1.00 mm thick wall care putty as per manufacture's instruction complete all as specified and directed. (Note : The complete white wash/colour wash to be removed and shown to department before applying wall care putty and quater wise approval of Engg-in-Charge shall be taken for radiness of wall for wall care putty.)

M & L for preparation of newly plastered surface of walls and applying POP putty of 1 mm thickness over plastered surface to prepare the surface even & smooth and applying two or more coats 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre with UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M & L for complete removal of existing treatment and applying POP putty of 1 mm thickness over plastered surface to prepare the surface even & smooth and applying two or more coats 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre with UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M & L for Preparation of new wood and wooden based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over coat of pink primer complete all as specified and directed.

M &L Preparation of old wood and wooden based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps 30 mm (when open) complete all as specified and directed.

M& L for 18/19 mm thick Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on both faces fixed with screws to timber frame work complete all as specified and directed.

S&F magnetic PVC catcher for kitchen cup board complete all as specified and directed.

S& F 100mm long Aluminium handles, cast type, anodised complete all as specified and directed.

Excavating in post holes (or simlar holes) each n exc. 0.50 cucm getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers n exc. 25 cm watering & removing surplus soil to a distance n exc. 50 m and making good the disturbed surface complete all as specified and directed.

M& L for PCC (1:3:6) type B-2 using 40 mm graded crushed stone aggregated for fixing of Post etc complete all as specified and directed.

S&F rolled mild steel Steel work in tubular trusses, poles, purlins, etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS grade ST-240 complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and.or riveted or forged into spikes, framed gurad bars, barred iron doors and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S & F mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Fixing only in repair wash basins, vitreous china, any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

Fixing only in repair kitchen Sinks or laboratory with plugs, washers and wastes; including fixing cantilever brackets and connecting union to waste pipe complete all as specified and directed.

Taking down shutter from the frame, exc 1 sqm but n.exc 2 sqm and refixing the same after necessary repair and fixed in the same opening complete all as specified and directed

Supplying, laying and testing of 100 mm internal dia of double wall corrugated (DWC) high density polythylene pipe (HDPE) and stiffness class 8 (SN-8) with ISI marked (With CML No ) with and including all fittings & jointing materials for connection of inspection chamber/WC to first manhole of the sewage line complete all as specified and directed.

S&F sheet glass, tinted, 4mm thick, glazing in aluminium frames, area not exc. 0.50 sqm in each pane, complete all as specified and directed.

S&F frosted glass, 4mm thick, glazing in aluminium frames, area not exc. 0.50 sqm in each pane, complete all as specified and directed.

Disconnecting existing tanks of capacity exc 250 ltr but not exc 500 ltr, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position after cleaning and removing all scales and dirt etc from tanks and from mouths of circulating pipes etc complete all as specified and directed.

S & F 125x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,complete all as specified and directed.

Dismantling of timber fillet, rails, posts, rafter, purlins, etc. under 40 Sqcm in Section in Unframed Work, complete all as specified and directed.

M&L for cement concrete 1:3:6, type-C-0 (12.5mm graded stone aggrgate) as in filling in steel frame/roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down ceiling fan, exhaust fan after disconnecting of all electric connections inclding dismantling blades and removing fan and blades to store to keep it in safe custody for refixing complete all as specified and directed.

Taking down unserviceable sub main wiring of any size two single core including earth wire and PVC conduit/ casing capping and removing materials on site and making good the disturbed surfaces of walls etc complete all as specified and directed.

Taking up or down of old unserviceable under ground cable from trenches or from wall / pole of any descriptions after necessary disconnecting the same complete all as specified and directed.

Taking down carefully unserviceable distribution board / main switches / KWH meter of any capacity including wooden board and making good the disturbed surfaces of walls, etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified and directed.

M&L for point wiring for one light / fan point controlled by one way switch 5/6 amps complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above of size not less than 1.63mm duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be sone through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost complete all as specified and directed.

All as per item No 124 here-in-before but for one Bell/Buzzer point controlled by one bell switch.

All as per item No 124 here-in-before but one 3 pin socket oulet 5 amps, on same board.

All as per item No 124 here-in-before for one light point controlled by two 2-way switches.

All as per item No 124 here-in-before but one 3 pin socket oulet 5 amps, on independent board.

All as per item No 124 here-in-before but for one 3 pin 15 Amps power point on independent board with 2.5 Sqmm size FR-LS PVC insulated unsheathed multistranded copper conductor cable and with 2.5 Sqmm FR-LS PVC insulated unsheathed copper conductor as earth wire, complete all as specified and directed.

S&F switch piano flush type, 05/06 Amps single pole, one way 240 volts white in colour complete all as specified and directed.

S&F switch piano flush type single pole, two way 5 Amp white in colour (ISI marked) complete all as specified and directed.

S&F socket outlet 5 pin, 230 Volts (ISI marked) flush type white in colour complete all as specified and directed.

S&F Switch socket combination 2 in 1, 3 pin, 5 Amp 230 Volts (ISI marked) flush type white in colour complete all as specified and directed.

S & F switch piano in white colour, flush type, single pole, one way 15 Amp, 230 Volts complete all as specified and directed.

S&F socket in white colour 2 in 1, 3 pin, 15 Amp flush type universal 230 Volts complete all as specified and directed.

S&F ceiling rose white in colour, PVC/ polycarbonate, isolated body (ISI marked), three terminals, complete all as specified and directed.

S&F Lamp holder/angle holder white in colour, 30 volts, PVC/Ploycarbonate type insulated body with black / white plate suitable for batten fittings / angle fittings complete all as specified and directed.

S&F stepped type electronic fan regulator white in colour, flush type AC, 230 volts suitable for 1200/1400 mm sweep energy saving fans, ISI marked complete all as specified and as directed.

S&F modular bell push in white colour, 5 Amp, flush type complete all as specified and directed.

S&F Call Bell, Ding Dong in white colour AC, 230 Volts, single pole surface type complete all as specified and directed.

S&F Decorative wall light fittings & fixture polycarbonate, suitable for 10W LED Lamp complete all as specified and directed. Make- Philips , Model No. Comet Wall Light 30575 equivalent make of Havells / Surya.

S&F Bulk head light fittings, in die cast aluminium housing & frosted glass suitable for 1 x 8W CFL complete all as specified and directed. Model - STUD, LBHP-10-CDL of make Crompton or equivalent make of Havells / Surya.

S&F LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified and directed.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified and directed. (Make: Havells or equivalent make as approved by GE.)

S&F sheet steel enclouser, TPN distribution boards, double door factory made 3 phase 415 volts, 4 way IP - 43 protection, metal door, provided with 100 A insulated phase bus bars / neutral bars with sprouts / earth bars / sticking saddles / cement spill protector / colour coded interconnecting wire set / cable ties / blanking plates and circuit identification labels and provn for MCB TPN as incomer and SP MCB as outgoing complete all as specified and directed. (Note: MCBs shall be measured & paid seperately.)

S&F sheet metal enclosure for DBs, SPN 8 way, 240 Volts, 200 Amps rated busbar, double door complete all as specified and directed.

S & F MCB, TPN, 415 volts, 10 KA, 63 Amps, 'C' Curve complete all as specified and directed.

S & F MCB SP, 240 volts, 6 Amps, 10 kA, C-curve complete all as specified and directed.

S&F MCB SP, 240 volts, 20 Amps, 10 KA, C-Curve complete all as specified and directed.

S & F RCBD, Double Pole, 40 Amps 240/415 Volt, 10 kA, C-curve, complete all as specified and directed.

S & F Dummy (Blanking) Plate 18 mm complete all as specified and directed.

M&L for concealed sub-main wiring alongwith earth wire of size of 2 x 6.0 Sq. mm + 1 x 6.0 Sq. mm earth wire, ISI marked, FR-LS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring complete all as specified and directed. NOTE : Two runs of 6 sqmm conductor for main and one run of 6 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

M&L for earthing with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to depth not less than 2.25m below the ground level with top edge of earth plate at a depth not less than 1.5m below the ground level connected to galvanized iron wire 4mm dia earth lead by means of bolts & nuts,check nuts & washers made of galvanised steel, earth strip protected by and including PCC (1:2:4) type B1 precast RCC cover slab (M-15) reinforced with 8mm dia TMT bars 100mm center to center bothways including one handle made of 10 mm dia round bar, including necessary excavation and earthwork in any type of soil, 20 mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15 mm bore medium grade galvanized steel tubing for drawing earth lead GI wire protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 2009 and testing on completion complete including dismantling the existing unserviceable earthing complete all as specified and directed.

Supplying, laying, jointing and testing of 35 Sqmm 3.5 core XLPE insulated,sheathed,armoured,heavy duty. LT. 1100 volts grade cable with aluminium conductor laid in trenches/pipes, fixed to poles/walls taking out the old burnt out cables complete all as specified and directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth and getting out in soft/loose soil or hard/dense soil for taking up or laying of cable complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above starting point complete all as specified and directed. (Note: Earth obtained from cable trenches shall be removed)

M & L for sand cusioning to the full width of trenches for protection of cables including punning down complete all as specified and directed. (Note: Thickness of sand cushioning shall be measured after punning down.)

M & L for brick well burnt locally available sub class 'B' laid over sand cushioning to cable in trenches keeping width of brick parallel to the length of cable for cable protection complete all as specified and directed.

M & L for GI tube, 50 mm bore, light grade with all fittings laid in trenches/through wall / under road or floor/ support for hanging of ceiling fan etc complete all as specified and directed.

Hanging only serviceable ceiling fan/Exthaust Fan obtained from item no 120 here-in-before and connecting up including provision of cable from ceiling rose or connector to fan and provn of fan hook wherever necessary complete all as specified and directed.

Fixing only serviceable electronic meter of 5/10-60 any type and make obtained from item no 123, here-in-before and connecting the same to distribution board complete all as specified and directed.

Fixing only serviceable tubelight fitting of any type and make obtained from item no 119, here-in-before including above incl replacement of 2 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and directed.

Fixing only old serviceable MCB, SP obtained from item no 123, here-in-before of any size and suitable capacity complete all as specified and directed.

S & F security LED light, 25 watt with high performance, pressure die-cast alumnium alloy housing, polyester powder coated with high efficiency polycarbonate UV stabilised cover, tempered protective polycarbonate diffuser, integrated high efficiency electronic driver with lower THD (< 10%), IP 20, CRI >=80, Colour Temp (CCT)-5700 K, Lumen efficacy of LED>145 Lm/W. Electronic driver & surge suppressor, power factor 0.95, operating range - 140 to 270 V, 50 HZ fixed with suitable fixing arrangement complete including LEDs with certidication LM 79 for luminare LM 80 for LED source including all necessary internally pre-wired and connecting up with GI pipe Bracket of suitable length bend to required shape with flat iron clamps and bolts for fixing including 3 core flexible copper conductor cable of sutiable size, ceiling rose to terminal block complete all as specified and directed.

S&F star reated BLDC Exhaust Fan with louvers, (ABS plastic rust proof body & blade), 200 mm sweep, 1600 RPM, 800 CMH air delivery, operating voltage 140 V to 285 V, 16 Watts with automatic flaps and connecting up including provision of 3 core flexible multistranded copper conductor of dize 0.75 Sqmm form ceiling rose to fan complete all as specified & directed. Make : Atomberg or equivalent make of Bajaj, Havells.

S&F star rated BLDC Exhaust Fan with louvers, polypropylene body,150 mm sweep, 2000 RPM, 356 CMH air delivery, operating voltage 140 V to 285 V, 11 Watts with automatic flaps and connecting up including provision of 3 core flexible multistranded copper conductor of dize 0.75 Sqmm form ceiling rose to fan complete all as specified & directed. (Make : Atomberg or equivalent make of Bajaj, Havells,Usha.)

Supply, installation, testing and commissioning of electric water heater, storage vertical type, BEE 5 star rated, 25 ltr capacity 230 volts AC, 50 Hz comprising of high wattage heating element for instant heating, extra thick SS inner tank of superior 304 grade, rust & shock proof ABS outer body, non-ferrous pressure plate with & including provision of Pressure relief valve and grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated, sheathed, stranded copper conductor cable/flexible chord complete all as specified.

S & F 5 star rated BLDC ceiling fans AC 230 Volts single phase 1200 mm sweep complete with all accessories including MS Hook, Nuts, Bolts and washer for hanging arrangement complete all as specified and directed. (Make: Usha ,Model- Energia 32, 5 Star or equavalent make of Bajaj/Crompton.

Boring holes horizontally under Road without damaging the surface of Road of any type by using trenchesless technology (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. (NOTE: GI Pipe laid shall be measured and paid separately under appropriate Item.

M/s Miza Enterprises

RC Madan

M/S UTTAM SAHA

M/S K.K.TRADERS

FRIENDS CONSTRUCTION