CONSTRUCTION OF MULTI LEVEL CAR PARKING AT NAGAR NIGAM LAND RISHIKESH

Amount

PART-I CIVIL WORKS

Earth Work

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

Beyond 30 cm girth upto and including 60 cm girth

Beyond 60 cm girth upto and including 120 cm girth

Beyond 120 cm girth upto and including 240 cm girth

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m, as directed by Engineer-in-charge.

All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All types of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Concrete Work

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from naturalsources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for :

Foundations, footings, bases for columns

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Reinforced Cement Concrete

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached plasters, buttresses, Plinth and String courses etc

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Edges of slabs and breaks in floors and walls

Under 20 cms wide

Weather shade, Chajjas, corbels etc., including edges

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

Concrete of M25 grade with minimum cemnt concrete of 330kg/cum

Concrete of M40 grade with minimum cemnt concrete of 390kg/cum

All works above plinth level upto floor V level.

Concrete of M25 grade with minimum cemnt concrete of 330kg/cum

Concrete of M40 grade with minimum cemnt concrete of 390kg/cum

Extra for R.C.C./B.M.C. work above floor V level for each four or part there of.

masonary work

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and fixing of chicken/ fiber mess in AAC block and RCC joint as per instruction of engineer in charge

Half brick masonry with non modular fly ash bricks of class designation 10, conforming IS :12894, in super structure above plinth and upto floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Extra for exposed concrete surface of ramp slab soffit and side beam over basic item rate i/c cost of making grooves as per plan / elevation ( plan area shall be measured).

Cladding Work

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite stone slab colour black, Cherry/Ruby red

Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Wood Work & PVC Work

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)

Second class teak wood

35 mm thick shutters

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 9.120.1 30 mm thick plain PVC door shutters

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding

9.27 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 9.27.1 35 mm thick shutters 9.27.1.1 with ISI marked M.S. pressed butt hinges bright finished of required size

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).

18 mm thick

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof siliconsealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Steel Work

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover

Extra for providing mechanical device chain and crank operation for operating rolling shutters

Exceeding 10.00 sqm and upto 16.80 sqm in the area

Providing and fixing T-iron frames for doors of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel membersshall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :

4.0 mm thick glass panes

Providing and fixing factory made ISI marked steel glazed windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Flooring

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing glass strips in joints of terrazo/ cement concrete floors

40 mm wide and 4 mm thick

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Size of Tile 600x600 mm

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for pre finished nosing to tread of steps of granite / marble stone

Roofing

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and mixing integral crystalline admixture of PENETRON/ KRYTON/ XYPEX / SIKA / PIDILITE / FORSOC make for waterproofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc.. at the time of transporting of concrete into the drum of the ready-mix truck , using integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R- 2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and applying two component instant setting 100% solids spray applied hybrid polyurea waterproofing coating having excellent tensile strength of 15MPa and elongation of >400% (as per ASTM D 412), adhesion to concrete of 2MPa (as per ASTM D 4541), puncture resistance of 1000N (as per ASTM 154) and static crack bridging of up to 2mm (as per ASTM C 836) applied @1.5 kg/Sqm., cracks shall be repaired by cutting V groove in 25x25 mm size and filling the same with polymer modified mortar( 1:3 Cement Mortar having polymer @10% by weight of cement) at the corners above the mother slab for a length of 150mm horizontally and 150mm vertically.

Providing and applying an average 65 mm thick spray applied CFC free polyurethane foam of approved make on Terrace conforming to ASTM D 7425 with a core density of 45-50 kg /m3 (as per ASTM 1622), thermal conductivity of 0.023 W/m.k at 25°C mean temperature (as per ASTM C518/91), U-value of 0.33 W/m2 °k meeting the requirement of ECBC & GRIHA, tensile strength of >400 kPa (as per ASTM D 1623/78), compressive strength >300 kPa (as per ASTM D 1623-03), closed cell content having apparent VOI of 96-98% (as per ASTM D 2856) and fire resistance property confirming to Class B2 as per DIN 4102. Before applying polyurethane foam, cracks shall be repaired by cutting V groove in 25x25 mm size and filling the same with polymer modified mortar( 1:3 Cement Mortar having polymer @10% by weight of cement). Base coat of highly elastomeric two component instant setting 100% solids spray applied hybrid polyurea waterproofing coating having excellent tensile strength of 15 MPa and elongation of >400% (as per ASTM D 412), adhesion to concrete of 2 MPa (as per ASTM D 4541), puncture resistance of 1000N (as per ASTM 154) and static crack bridging of up to 2mm (as per ASTM C 836 applied at 1.5 kg/Sqm at the corners above the mother slab for a length of 150mm horizontally and 150mm vertically. Over the entire polyurethane foam, supplying and applying two component instant setting 100% solids spray applied hybrid polyurea waterproofing coating having excellent tensile strength of 15MPa and elongation of >400% (as per ASTM D 412), adhesion to concrete of 2MPa (as per ASTM D 4541), puncture resistance of 1000N (as per ASTM 154) and static crack bridging of up to 2mm (as per ASTM C 836) applied @1.5 kg/Sqm. 150 gsm Geotextile (non-woven polyester) over the entire membrane maintaining proper overlaps shall be applied. Make - MYK ARMENT, ARDEX ENDURA, SIKA, ALCHIMICA, PIDILITE

Finishing

12 mm cement plaster of mix

1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:

1:6 (1 cement: 6 coarse sand)

6 mm cement plaster of mix

1:3 (1 cement : 3 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand)

White washing with lime to give an even shade :

New work (three or more coats)

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Applying priming coat:

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :

15 mm wide and 15 mm deep groove

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification.

Two or more coats on new work

Aluminium Work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For Fixed Portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge

Powder coated minimum thickness 50 micron aluminium

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Water Proofing

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge.

d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Road Work

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with all lead and lift.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV ofASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as

Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

New Technologies and material

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately)

Non-Schedule Items - Civil

Polyurethane Flooring: 6mm Thick PU Floor Polyureathane Resin iron filled floor Screed System of MATT FINISH at 6.0mm Surface Preparation : Providing and roughening the smooth surface to provide the mechanical key for subsequent application, grinding all sharp edges to make them flush with the surface, making groove of 12mm X 12mm in size at approximately 100mm awayparallel from wall and adjacent to doorways, covering not more than 20 Smtr, cleaning the all floor area to make it free from all dirt, dust and other contaminants, etc and completeas per manufacturer's specifications. Scratch Coat: - Providing and installing APCOFLOR PU CRETE 4K XL at 1mm thick as scratchcoat using flat trowel by mixing all 4 components and colour pigment in mixing vessel using heavy duty slow speed drilling machine fixed with mixing paddle, etc and complete as per manufacturer's specification. Top coat: Supply and apply of APCOFLOR PU CRETE 4K XL Polyurethane Floor Topping on Concrete Floor. The floor concrete should be prepared with scarification or captive shot blasting process. The dust and debris to be removed by Industrial Vacuum Cleaner. Anchor Grooves to be cut of size 1.5 to 2 times the thickness of the floor topping. Along the perimeter of floor topping, around columns, open drains, along construction joints, cable trenches, etc., Open up all the cracks in to anchor grooves. Fill all the anchor grooves with APCOFLOR PU CRETE 4K XL Screed material. Provide a scratch coat of APCOFLOR PU CRETE 4K XL @ 2 to 2.25 kg per Sqm with groove filling, allowing to cure overnight. Complete the topping with APCOFLOR PU CRETE 4K XL @ 2 kg per Sqm/mm. Allow to cure for the necessary period as per Manufacturers Instructions.

Supply of 2 Level Stack Parking System with Hydraulic based Technology accommodating 2 Cars per module with car carrying capacity of 2000 kg on platform and Car Dimension of 5000 mm length x 2000 mm height (SUV) at Ground level, with average retrieval/parking time not more than 50 seconds. Power pack motor capacity of 1.5 KW, platform thickness 1.5MM, Entry plate and Side Member thickness 3MM. Manufacturing standard; all welding should be TUV certified. One power Pack connected to 5-7 Units Having following safety features as 1. Mechanical locks at every 100MM from Ground to platform level. 2. Platform arrangement with support structure. 3. Mechanical locks at every 100MM from Ground to platform level. 4. All Hydraulic/Electrical pipe will be covered with GI Channel pipe cover. 5. Hydraulic NRV value should be placed at ground level for easy manual rescue of cars. 6. Chain Magnet Cover plate on each unit. 7. Tyre stopper 8. Vairous Platform Width as per site conditation i.e. 2100MM to 2400MM 9. Pregalvanized item: Platform Side Member, Platform, Chain cover, Pipe cover 10 Sensor if required

Glass Reinforced Concrete (G.R.C) Screens/ Jali Providing and fixing Glass Reinforced Concrete (G.R.C) Screens/ Jali customized as per design, dimensions as per drawings in approved shade in overall thickness of 40mm, or inner design membrane between 30-35mm and borders 50mm, casted with layering technique Power Spray methodology have weight approximately between 3.75 -4.5 Kg per Sq. Ft. The screens casting shall take place with layering methodology using- Direct Power Spray machines. The screens shall be casted from 53 grade White Portland Cement manufactured by Fine graded, sieved Quartz & Silica Sand, reinforced with Alkali Resistant Glass Fiber manufactured between 4-5% by having Zirconia content at least 16%, Super Plasticizers and UV resistant Synthetic inorganic pigments should be used for pigmentation.

Providing signage viz display/name plate and like of required size made out of 20 guage thick stainless steel (304 grade) including engraved subject matter, message (Hindi/English and / or bilingual), symbols, borders and logo etc. The engraved letter, borders etc. to be furnished with paint etc. of reqyured colour scheme and the plate to be fixed to wooden/wall surface with 25mm long stainless steel spacer/stud all complete as per direction of Engineer in Charge.

Graffiti painting on wall as approved logo by high gloss acrylic colour before making logo, prepare the surface clean, fill POP in voids, apply 1mm white birla putty and primer including material, labour and T&P etc. all complete under instruction of Engineer-in-charge.

PART-II LANDSCAPE : HORTICULTURE & SOFTSCAPE

EARTHWORK

Uprooting rank vegetation and weeds by digging the area to a depth of 60cm removing all weeds and other growth with roots by forking re­peatedly, breaking clods,rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

Rough dressing the trenched ground including breaking clods as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

Supplying and stacking of good earth at site including royalty and carriage up to 5 km as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

TREES & SHRUBS

Digging of pit for trees in ordinary soil and refilling the same with the exca­vated earth mixed with manure or sludge flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (upto 0.6mX 0.6mx 0.6m) for trees etc. complete as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

Digging of pit for small plants /shrubs in ordinary soil and refilling the same with the exca­vated earth mixed with manure or sludge flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts etc. complete as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

Supplying and planting below mentioned best quality container- grown healthy trees of species as specified and with an average height and as age as mentioned as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge. All trees to be approved by Engineer-in-Charge before planting.

Neem of height 3m - 4m (3 to 4 years old) well developed with thick stem

Karanja of height 4m -5m (3 to 4 years old) well developed with thick stem

Akashmalli of height 3m - 4m (3 to 4 years old) well developed with thick stem

Amla of height 3m - 4m (3 to 4 years old) well developed with thick stem

Mango of height 4m -5m (3 to 4 years old) well developed with thick stem

Kochila of height 4m -5m (2 to 3 years old) well developed with thick stem

Champa (white,red, pink) of height 3m-4m (2 to 3 years old) well developed with thick stem

Baul of height 4m -5m (3 to 4 years old) well developed with thick stem

Ashoka of height 4m -5m (3 to 4 years old) well developed with thick stem

Arjun of height 3m-4m (2 to 3 years old) well developed with thick stem

Bahunia purpurea (kanchan) of height 4m-5m (3 to 4 years old) well developed with thick stem

Peepal/ Banyan Tree of height 4m -5m (3 to 4 years old) well developed with thick stem

Supplying and planting below mentioned best quality container- grown healthy shrubs/plants of species as specified and with an average height and as age as mentioned as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge. All trees to be approved by Engineer-in-Charge before planting.

Aparajita (black & height) of height up to 1 mtr (1 to 2 yrs) old

aswagandha of height up to 2 mtr (1 to 2 yrs) old

dhannantari of height up to 2 mtr (1 to 2 yrs old)

ganga siuli of height up to 2 mtr (1 to 2 yrs old)

kamini of height up to 1 mtr (1 to 2 yrs old)

mandar of height up to 1 mtr (1 to 2 yrs old)

rukunaa hatapochaa of height up to 1 mtr (1 to 2 yrs old)

sadabihari (red & white) of height up to 1 mtr (1 to 2 yrs old)

Jasmine of height up to 1 mtr (1 to 2 yrs old)

GROUND COVERS

Grassing with broad leaf grass (Axonopus compressus), free from weeds & having proper roots including earth filling, fertilizer, watering, labour charges, curation and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and filt for mowing including supplying good earth if needed as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

FERTILIZERS

Supply and applying of chemical fertilizer before or after as per requirement, as per Schedule of Rates,Analysis of Rates and Specifications (Horticulture & Landscaping) 2020 and direction of Engineer in Charge.

Urea / Ammonium Sulphate (30gm/M²)

Bone Meal (150gm/M²)

Potassium Sulphate or Murate of Potash (20gm/M²)

Provision of insecticides (10ml IN 10 ltr/M²)

PART-III PLUMBING

SUB-HEAD - I (FIXTURES)

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board

510x1040 mm bowl depth 250 mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 450x300 m

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder :

C.P. brass

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet

Sand cast iron S&S as per IS: 3989

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

150 mm diameter

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour.

Circular type

100 mm nominal dia

SUB-HEAD - I (SANITORY FIXTURES) NON DSR ITEMS

Providing and fixing white color vitreous wall mounted European low flow W.C. with concealed cistern with CP bolts, nuts, CI brackets, with ‘P’ or ‘S’ trap including seat cover, C.P. Fixtures, like bolts & rubber buffers etc. complete including with 15 mm dia CP connection pipe, Pan connector complete including cutting and making good the walls and floors wherever required. as approved by engineer in charge.

Providing and fixing white vitreous low flow wall mounted wash down water closet with seat cover with concealed Cistern for handicap people, with CP nuts & bolts, Pan connector including bracket, arm support of S.S Swing handicap grab bar - complete all respect. -as approved by engineer in charge.

Providing and fixing low flow 15mm bib cock with Brass threaded flange complete including cutting and making good the tiles wherever required bib cock shall be of approved make to compliance GRIHA rating.

Providing and fixing 15mm dia low flow S.S Single-lever high-neck basin mixer for wash basins and sinks of approved make including cutting and making good the tiles / marble wherever required make to compliance GRIHA rating.

Providing and fixing S.S Single leaver concealed diverter with chrome upper trim with spout wall flange complete in respects.

SUB-HEAD II (WATER SUPPLY)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

External work

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes

65 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc

External work

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

20 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

32 mm nominal bore

Horizontal

40 mm nominal bore

Horizontal

50 mm nominal bore

Horizontal

Vertical

65 mm nominal bore

Horizontal

80 mm nominal bore

Horizontal

Vertical

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required

80 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

SUB-HEAD III (DRAINAGE)

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

200 mm diameter S.W. pipe

250 mm diameter S.W. pipe

300 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

100x100 mm size P type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

200 mm diameter

250 mm diameter

300 mm diameter

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)

Extra for depth for manholes :

Size 90x80 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design

With 20x20 mm square bar

SUB-HEAD - III (DRAINAGE) NON DSR ITEMS

Providing and fixing UPVC(SWR) Type-B of size 110 mm x75x40 mm Multi Floor Trap along with 110 mm dia PVC pipe up to floor level and PVC grating of approved make with suitable jointing to ensure leak proof service as per instruction for laying & jointing recommended by the manufacturer and including cement concrete 1:2:4 under and around the multi floor trap where required up to floor level complete in all respects including cutting and making good the walls and floors etc. complete in all respect as per full satisfaction of the Engineer – in – Charge. ).

With 63 mm i/d outlet. ( 110 x 75 x 40)

Providing and fixing UPVC(SWR) Type-B of size 110 mm x 90 mm Nahani Trap along with 110 mm dia PVC pipe up to floor level and PVC grating of approved make with suitable jointing to ensure leak proof service as per instruction for laying & jointing recommended by the manufacturer and including cement concrete 1:2:4 under and around the Nahani trap where required up to floor level complete in all respects including cutting and making good the walls and floors etc. complete in all respect as per full satisfaction of the Engineer – in – Charge.

With 90 mm i/d outlet.

Providing and fixing Upvc 110mm P Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections

Providing and fixing end cap (door piece) of Upvc for cleaning.

with 110 OD

Providing, fixing and jointing UPVC (SWR) pipe in vertical and horizontal position Type-B for soil waste, rain water and vent or anti syphon age pipe of approved make including all fittings (plain or door) e.g. bends, junctions, cowls, offsets, access pieces jointing including fixing the pipe on the wall/ceiling with suitable clamps ,holder bat clamps and anchor fastener of approved design to Upvc (spun) pipe embedded, cement concrete block 10x10x 10 cm of 1:2:4 ( 1 cement: 4 coarse sand: 4 graded stone aggregate 20 mm nominal size), cutting holes in wall and floors, excavation, refilling and disposal of surplus earth where required and marked good complete etc. and as per direction of Engineer in Charge. Make - (Jain Plumbing or its equivelent price in prince/finolex).

160 mm dia

110 mm dia

50 mm dia

40 mm dia

SUB-HEAD - IV (WATER PUMPS & TREATMENT PLANT)

Water pumps

Providing, fixing, testing and commissioning of monoblock vertical in line type pump set with SS casing, SS impeller and SS shaft complete with suitable motor and cement concrete foundation. Motor to be suitable for 400/440 volts, 3 phase 2900 RPM.

Filter feed pumps (Common for MLCP & Staff quarter) Pump capacity - 1.5 lps Head - 20 m RPM - 2900

Domestic water transfer pumps (For staff quarter) Pump capacity - 1.0 lps Head - 35 m RPM - 2900

Providing, fixing, testing and commissioning of factory assembled skid mounted variable freqency drive hydropneumatic system comprising of following items. (For domestic water supply). MLCP

2 Nos. Vertical in line pumps complete in SS coupled with TEFC motor (1W+1S).

Pump capacity - 2.5 lps Head - 60 m RPM - 2900

1 No. 100 litres vessel with inter changeable butyl rubber membrane.

1 No. Variable speed drive Electric control panel with controller relays, sequence timer for alternate operation of pumps, electrical wiring, cabling from panel to pumps, level controller complete with all accessories as per manufacturer specifications.

Accessories like butterfly valves, NRV & Y-strainer on suction and butterfly valves & NRV on discharge, pressure gauge suction, discharge header and base frame etc., complete as required.

Hydropneumatic system as described above.

Providing, fixing, testing and commissioning of factory assembled skid mounted variable freqency drive hydropneumatic system comprising of following items. (For flushing water supply). MLCP

2 Nos. Vertical in line pumps complete in SS coupled with TEFC motor (1W+1S).

Pump capacity - 1.7 lps Head - 70 m RPM - 2900

1 No. 100 litres vessel with inter changeable butyl rubber membrane.

1 No. Variable speed drive Electric control panel with controller relays, sequence timer for alternate operation of pumps, electrical wiring, cabling from panel to pumps, level controller complete with all accessories as per manufacturer specifications.

Accessories like butterfly valves, NRV & Y-strainer on suction and butterfly valves & NRV on discharge, pressure gauge suction, discharge header and base frame etc., complete as required.

Hydropneumatic system as described above.

Providing, fixing, testing and commissioning non clog type mono block submersible drainage pumps with CI casing & CI impeller suitable for handling solids of 12 mm size

Capacity 4.0 lps & Head 12m (Pump room)

Providing, fixing, testing and commissioning of liquid level controller cum indicater comprising single SS 304 Probe stem of suitable length based on the height of the tank. The probe shall have 5 nos Magnetic Bi-stable sensors with 0-5000 ohms resistance to act as potentiometer. The Sensors to be actuated by a single actuating float to give analog output based on level at any stage. Float shall be provided with 4 Digit Red LED 7 segment display of 12.5 mm, to be connected with the Probe unit. The unit shall have High and Low alarm to be set according to requirement based on levels indicated.

For domestic Filter feed pumps.

To start domestic filter feed pumps at low water level in domestic treated water under ground tank and stop at high water level in treated water tank and stop at low water level in domestic raw water tank.

For domestic water transfer pumps (For Staff quarter)

To start pump at low water level in overhead tank and stop at high water level in overhead tank and low water level in under ground tank.

Providing, fixing, testing and commissioning of dust, damp and vermin proof, free floor standing factory built sheet steel enclosed nondrawout modular panel for pumps, fabricated out of suitable sized square tubular section and covered with 2mm thick CRCA sheet, hinged doors and partitions all 2mm thick , duly painted complete with earth bus, necessary metering protections & indications and mounted with the following including all inter connection etc. (Including earthing).(Pumps in pump room)

One No.63 amps TP incoming MCCB complete with the following:

Over voltage and under voltage tripping machanism for persistent voltage fluctations of more than ±10% of the rated voltage for more than 5 minutes. (1set)

Phase indicating lamps with toggle switches.

Indication lamps for ON/OFF/TRIP status of motors.

Aluminium bus bar of 100 amps for three phase and neutral.

Outgoing Feeders/Starters.

16 amps TPN MCB with DOL starter each suitable 1 HP for filter feed pumps (2 Nos).

16 amps TPN MCB with DOL starter each suitable for 1 HP for domestic water supply for staff quarter (2 Nos).

16 amps TPN MCB each suitable for 1.5 HP drainage pumps panel in pumproom (1 Set).

32 amps TPN MCB each suitable for 4 HP hydropneumatic pumps panel for domestic water supply (1 Set). (For domestic water supply)

16 amps TPN MCB each suitable for 3 HP hydropneumatic pumps panel for flushing water supply (1 Set). (For flushing water supply)

32 amps TPN MCB each suitable for 5 HP tubewell pumps panel (1 Set).

Rotary manual/auto/off switch. (4 Nos.)

Spares

16 amps TPN MCB - 2 Nos.

32 amps TPN MCB - 2 Nos.

Providing, fixing, testing and commissioning of dust, damp and vermin proof, wall mounted factory built sheet steel enclosed nondrawout modular panel for pumps, fabricated out of suitable sized square tubular section and covered with 2 mm thick CRCA sheet, hinged doors of 2 mm thick CRCA sheet, duly painted complete with earth bus, necessary metering protections & indications and mounted with the following including all inter connection etc. (Including earthing). (For starter panels of drainage pumps in pump room ).

32 amps incoming MCB (1 No.)

Phase indicating lights with toggle switches and shall be protected by 2 amps MCB's. (2 sets)

Ampere meter 96mm square panel type of appropriate range. (1 set)

16 amps outgoing MCB (2 Nos.)

Fully automatic DOL starters with push buttons indicating lights and overload relay each for drainage pump. (2 Nos.)

Single phasing preventors. (2 Nos.)

Rotary manual/auto/off switch. (2 Nos.)

Space of one liquid level controller

Providing, laying, jointing, testing, & commissioning the PVC insulated & sheathed FRLS (Flame Retardant Low Smoke) Armoured Cables of 1.1 K.V. Aluminium Conductor including supplying and making end termination with brass compression glands:

3 Core x 2.5 sq.mm

4 Core x 2.5 sq.mm

4 Core x 4 sq.mm

4 Core x 6 sq.mm

Providing, fixing, testing and commissioning following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150mm width x 50mm depth x 1.6 mm thickness.

B. WATER TREATMENT SYSTEM

Providing, fixing, testing and commissioning skid mounted vertical FRP Dual Media pressure filter complete with initial charge of filter media, face piping and valves accessories, painting, testing and commissioning complete.

For Domestic water supply Capacity 5400 lph Working pressure 2.5 kg./cm2 Flow velocity: 10m3/hr/m2 Design pressure 4 kg./cm2

Providing, fixing, testing and commissioning skid mounted vertical FRP Activated carbon filter complete with initial charge of filter media, face piping and valves accessories, painting, testing and commissioning complete.

For Domestic water supply Capacity 5400 lph. Working pressure 2.5 kg./cm2 Flow velocity: 10m3/hr/m2 Design pressure 4 kg./cm2

Providing, fixing, testing and commissioning of skid mounted FRP “Cation” ION Exchange water softener complete with initial charge of filter media, face piping, brine tank, valves & accessories, testing and commissioning complete.

For HVAC water supply system Capacity 5400 lph. Total hardness = (as per tubewell water at site) OBR = 40000 ltrs Working pressure 2.5 kg./cm2 Design pressure 4 kg./cm2

Providing, fixing, testing and commissioning bulk water meter with direct reading dial in KL, all internal parts and strainer in gun metal/brass.

40 mm dia for 5400 lph rate of flow for filter.

Providing, fixing, testing and commissioning direct reading rate of flow Rota Meter

40 mm dia for 5400 lph rate of flow for filter.

Providing, fixing, testing and commissioning gun metal dial type pressure gauge (150mm dia) of rating 0-10 kg./cm2 with gun metal isolating cock pig and connecting pipe.

Providing, fixing, testing and commissioning of chlorinator with metering pump mounted on HDPE white tank suitable for operation on 220 ± 5% single phase, 50 Hz AC supply, including cables from metering pump to control panel compete in all respects.

Suitable for flow rate of 5400 lph

C.SUCTION AND DELIVERY PIPES AND VALVES FOR WATER SUPPLY PUMPS

Providing, fixing, testing and commissioning Y-strainer with flanged ends with test prssure 21.09 kg/cm2.

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Part-IV FIRE FIGHTING

Hydrant Pump & Sprinkler pump

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered with anti vibration pads.

2850 lpm at 88 m Head

Hydrant Pump

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump)

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump)

Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

2850 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.

M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

180 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required

Suitable cement concrete foundation duly plastered

900 lpm at 35 m Head

450 lpm at 35 m Head

Fire Panel

SUB HEAD - II ( Hydrant, Sprinkler, Piping & Accessories)

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

200 mm. dia (wall thickness = 6.3 mm)

150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

250 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

65 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gun Metal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

3 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

100mm dia

150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

80 mm dia

100 mm dia

150 mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

SUB HEAD - II ( Hydrant, Sprinkler, Piping & Accessories) MR Items

Supplying and erecting M.S./CRCA cabinet for housing Floor Hydrant valve, hose pipe, hose reel and branch pipe (size 1000 x 736 x 736 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying, Installation, Testing and Commissioning of standard Fire Man's axe with heavy insulated rubber conforming to IS : 926

SUB HEAD - III (Fire Control Panels and Cabling) DSR ITEM

Incomings

Outgoings

Main Fire Pump

Jockey Pump

Diesel Engine Control

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3 X 70 sq. mm (35mm)

3½ X 240 sq. mm (62mm)

3 X 10 sq. mm (22mm)

SUB HEAD - III (Fire Control Panels and Cabling) MR ITEM

Supplying and Laying of XLPE insulated, PVC sheathed 1.1 KV grade armoured U.G. Cable of following sizes on surface/in existing cable tray suitably clamped as required.

31/2x 240 sq.mm.(aluminium conductor)

3 x 70 Sqmm(aluminium conductor)

3 x 10 Sq mm (Copper conductor)

2 x 2.5 Sq mm (Copper conductor)

Providing and fixing dust and vermin proof Motor Control Panel fabricated from 14 SWG MS sheet with stove enamelled paint and comprising of: (for Fire Booste pump).

One feeder of 63 ampere 4 Pole ELCB.

One fully automatic star delta starter with push buttons and indicating lights.

Three Neon Phase indicating lights on the incoming Main.

One Ampere meter 96mm square panel type of appropriate range.

Etched plastic identification plates for all switch gears.

Space for 32 ampere MCB.

All internal wiring should be colour coded from incoming main to switchgear, starters, meters, indicating lights.

Providing and fixing dust and vermin proof Motor Control Panel fabricated from 14 SWG MS sheet with stove enamelled paint and comprising of: (for Fire Booste pump).

One feeder of 32 ampere 4 Pole ELCB.

One fully automatic star delta starter with push buttons and indicating lights.

Three Neon Phase indicating lights on the incoming Main.

One Ampere meter 96mm square panel type of appropriate range.

Etched plastic identification plates for all switch gears.

Space for 32 ampere MCB.

All internal wiring should be colour coded from incoming main to switchgear, starters, meters, indicating lights.

SUB HEAD - IV MISCELLANEOUS SAFTY ITEMS

Providing and fixing CO2 type cylindrical shape fire extinguisher with fixing hangers, hose, brackets, screws to required size etc.complete as per IS:15683:2006 - wall mounted type. Capacity 4.5 Kg.

Providing and fixing fully charged ABC powder type (Mono-Ammonium Phosphate - MAP 90) portable fire extinguishers conforming to IS:15683, fixed to wall with brackets complete with initial charge. (Note: The cost for stand of fire extinguisher shall be included in this rate) Capacity 6 Kg.

Providing and fixing mechanical foam type (ISI marked) fire extinguishers consisting of welded M.S. cylindrical body squeeze lever discharge valve 30 cm long high pressure discharge hose, discharge nozzle suspension bracket as per IS:15683 marked finished externally with red enamel paint and fixed to wall with brackets complete with internal charger. Capacity 9 lit.

Providing, fixing, testing and commissioning reinforced Neoprene Flexible Pipe connectors with all accessories on all pumps delivery.

Suitable for 20 Kg/cm2

Providing, fixing, testing and commissioning of FM approved (If instructed by engineer in charge)Venturi type Flow meter of approved brand of manufacture, with accessories etc., complete.

100 mm dia

Providing, fixing, testing and commissioning fire retardent / extinguishing electrical insulated synthetic mat of 3mm thick ±10% conforming to latest BIS doc no.-ET-02(5440) meeting requirements of IS 3043 / IS 5216 (Part I, II & III), IS 8437 & IEC 479 suitable for all voltages not exceeding 3.3 KV AC supply and having minimum width of 1000mm ± 20mm and including supply of required quantity of adhsive / compound and fixing the same at site as per site requirement.

PART-V RAIN WATER HARVESTING

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete.

On concrete work

19.19 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

Circular shape 560 mm internal diameter

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer ‐in‐charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer‐ in‐charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

200 mm dia

PART-B ELECTRICAL,LV,SOLAR,HVAC,PARKING MAGAGEMENT SYSTEM

PART-I INTERNAL ELECTRICAL

Sub Head - I - Point Wiring

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. (AC/Geyser)

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Sub Head - II -Distribution Board

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 Way, Double Door

12 Way, Double Door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)

4 way (4+12), Double door

6 way (4+18), Double door

8 way (4+24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 amps (30mA)

63 amps (30mA)

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Sub Head - III - Supply And Installation of light Fixture

The rates shall include all components that may be required to make the supply and installation complete in all respects such as :

All lamps

Internal wiring between accessories

Earthing terminal

Complete provision for installation

Suitable length of GI down rod, hanger and connecting wires where called for.

Wires for connecting the fixtures to the point through connector block.

All metal blocks to serve as base of fixtures

Bonding with earth wires.

Drilling holes in supports wherever required

Fixing clamps, GI bolts and nuts, brass screws, saddles, rawl bolts and other fixing accessories as required.

All recessed type fixture shall be considered with suitable length of flexible G.I. conduit.

Testing of all fixtures & fans before and after installation.

Supply of lighting Fixturte

Supply of the following lighting fixtures with all fixing accessories etc. as required.

12W SURFACE MOUNTED LED DOWNLIGHTER Supply of suitable for general lighting surface downlighter made of Pressure die cast aluminium suitable for general lighting. Luminaire should have die cast heat sink with polycarbonate cover. The luminaire should have CRI > 80 and CCT of 4000/5700K, SDCM<3 as per ANSI Bin C78.377A. The luminaire shall be compliant with IP40 classification.The fixture should have a minimum system efficacy of 120 lumen/Watt and a minimum system lumen output of 1440 lumens and maximum system wattage of 12Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 45 deg C. The electronic driver used shall have a power factor >0.95@full load , THD <10%, Surge protection 2.5KV, Operating voltage range: 100-265V AC, Fixture should have class I indulation. The fixture should comply with the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Including 3 core 2.5 sq.mm FRLS PVC insulated and PVC sheathed copper conductor cable and earthing etc. upto suitable point complete as required. Dimensions: Ø118x64mm (±2mm), Weight should not be more than 0.40Kg. Approved Model: Wipro LD06-151MLC-XXSMG1 or equivalent in LT/Regent/Trilux

15W SURFACE MOUNTED LED DOWNLIGHTER Supply of suitable for general lighting surface downlighter made of Pressure die cast aluminium suitable for general lighting. Luminaire should have die cast heat sink with polycarbonate cover. The luminaire should have CRI > 80 and CCT of 4000/5700K, SDCM<3 as per ANSI Bin C78.377A. The luminaire shall be compliant with IP40 classification.The fixture should have a minimum system efficacy of 120 lumen/Watt and a minimum system lumen output of 1800 lumens and maximum system wattage of 15Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 45 deg C. The electronic driver used shall have a power factor >0.95@full load , THD <10%, Surge protection 2.5KV, Operating voltage range: 100-265V AC, Fixture should have class I indulation. The fixture should comply with the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Including 3 core 2.5 sq.mm FRLS PVC insulated and PVC sheathed copper conductor cable and earthing etc. upto suitable point complete as required. Dimensions: Ø152x71mm (±2mm), Weight should not be more than 0.45Kg. Approved Model: Wipro LD06-171MLC-XXSMG1 or equivalent in LT/Regent/Trilux

18W SURFACE MOUNTED LED DOWNLIGHTER Supply of suitable for general lighting surface downlighter made of Pressure die cast aluminium suitable for general lighting. Luminaire should have die cast heat sink with polycarbonate cover. The luminaire should have CRI > 80 and CCT of 4000/5700K, SDCM<3 as per ANSI Bin C78.377A. The luminaire shall be compliant with IP40 classification.The fixture should have a minimum system efficacy of 120 lumen/Watt and a minimum system lumen output of 2160 lumens and maximum system wattage of 18 Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 45 deg C. The electronic driver used shall have a power factor >0.95@full load , THD <10%, Surge protection 2.5KV, Operating voltage range: 100-265V AC, Fixture should have class I indulation. The fixture should comply with the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Including 3 core 2.5 sq.mm FRLS PVC insulated and PVC sheathed copper conductor cable and earthing etc. upto suitable point complete as required. Dimensions: Ø152x71mm (±2mm), Weight should not be more than 0.45Kg. Approved Model: Wipro LD06-221MLC-XXSMG1 or equivalent in LT/Regent/Trilux

2'x2' 36W RECESSED MOUNTED LED LIGHT Supply of 36W Recess mounted LED 2'x2' luminaire delivering an initial system lumen of 4680 lumens & the luminaire shall be with system efficacy ≥ 130lm/W. Housing: CRCA white powder coated white, Optics: HET polycarbonate, IP20 Protection. The operating CCT shall be 4000/5700K with CRI of ≥80, SDCM<3. The luminaire shall be BIS Registered with isolated type electronic driver in polycarbonate / metal enclosure with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.90, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be of same make and made in India for ease of repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 4KV with High and Low Input Voltage Cutoff protection. The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Dimension: 595 X 595 x 36 mm ± 2mm, Weight: 1.4Kg Approved Model: Wipro CRCO10R036HE40G4ML or equivalent in Regent/Trilux

20W SURFACE MOUNTED LED TUBE LIGHT Supply of 20 Watt 4 feet Surface / Suspended / Wall Mounted IP20 LED Batten with minimum luminaire system efficacy of 100 lm/w having a color temperature of 5700K and housing should made up of Aluminium Anodized Extruded with high efficiency Polycarbonate diffuser with intergrated driver, LEDs used are SMD, Life of LED 50000 burning Hrs. @L70 Lumen maintenance, CCT 5700K, CRI≥80, PF≥0.95 & THD<10%, an operating Voltage Range of 150 - 270 VAC. Minimum Internal Surge Protection 2.5KV. The fixture design should comply driver leakage current as per as per IEC 60598 along with BIS certification for LED Driver & Luminaire. Luminaire manufacture shall provide LM79 report from NABL accredited lab. Dimension: 1202 X 27.8 X 36.5mm, Weight: 0.30Kg. Approved Make: Wipro LL20-281-XXX-65AL1 or equivalent in Regent/Trilux/LT

20W WALL MOUNTED LED TUBE LIGHT Supply of 20 Watt 4 feet Surface / Suspended / Wall Mounted IP20 LED Batten with minimum luminaire system efficacy of 100 lm/w having a color temperature of 5700K and housing should made up of Aluminium Anodized Extruded with high efficiency Polycarbonate diffuser with intergrated driver, LEDs used are SMD, Life of LED 50000 burning Hrs. @L70 Lumen maintenance, CCT 5700K, CRI≥80, PF≥0.95 & THD<10%, an operating Voltage Range of 150 - 270 VAC. Minimum Internal Surge Protection 2.5KV. The fixture design should comply driver leakage current as per as per IEC 60598 along with BIS certification for LED Driver & Luminaire. Luminaire manufacture shall provide LM79 report from NABL accredited lab. Dimension: 1202 X 27.8 X 36.5mm, Weight: 0.30Kg. Approved Make: Wipro LL20-281-XXX-65AL1 or equivalent in Regent/Trilux/LT

LINEAR CHANNEL LIGHT Supply of 35±2mm width IP40 linear suspended standalone fitting made of Extruded Aluminium housing duly powder coated White (RAL9016) With High Efficiency prismatic diffuser. Fixture should have office compliance i.e UGR<19. Fixture should have minimum efficacy at System level (Not Chip Level) >100lumens/watt and a minimum system lumen output of 3000 (downlight) lumens and maximum system wattage of 30W. Luminaire should have Life of 50000hrs@L70B50 Lumen maintenance at 45deg C ambient temperature, CCT up to 4000/5700/6500K, IP40, IK02, CRI >80, PF >0.95, THD<10% at full load and an operating Voltage Range of 140 - 270 Internal Surge Protection 3KV. The fixture should comply with the parameters as per IS10322. The LED driver should comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Including 3 core 1.5 sq.mm. Dimension: 1200 X 35 X 72 ±2 mm, Weight: 1.4Kg Approved Make: Wipro LM04-401-MLCXXUPWX or equivalent in Trilux/Regent

DESIGNER LIGHT Supply of 460mm dia IP20 Pendent Mounted Ring LED with designer mesh type design on the sides. Fixture to be made of Aluminum housing in white finish with High Efficiency Translucence (HET) diffuser. LED Used shall be SMD type with Minimum system Lumens 2400 @30W & efficacy 80lm/W,Life of fixture : 50000 burning Hrs. @ L70 Lumen maintenance, CCT of 4000K (SDCM<=3), CRI Ra >=80, PF >0.95, THD<10% at full load, operating Voltage Range of 150-270 V AC. Minimum Internal Surge Protection 2.0KV. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate BIS approval. Approved Make: Wipro LM46-341-MLC-40-WH or equivalent in Regent/Philips

10W LED MIRROR LIGHT Supply of 2ft length, 10W LED Mirror luminaire wall mounted delivering minimum system lumen of 1100 lumens & the luminaire shall be with system efficacy 110 lm/W. The luminaire Housing shall be made of extruded aluminium & the diffuser shall be of PMMA/PC. The operating CCT shall be 4000/5700/6500K with CRI of ≥80, SDCM<5. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95. LED Life with L70 Criteria should be 50,000 hours. IP20 protection. The LED Driver shall be easily available in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2.5KV. The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Approved make: Wipro LL20-111XXX40AL1ML or equivalent in Regent/Trilux

BULK HEAD LIGHT Supply of 10W Wall mounted LED Bulkhead Light delivering minimum system lumen of 1000 lm & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing & Rim is Pressure Die Cast Aluminium, IP65, IK10, Optics: Polycarbonate Opal high transmissive Diffuser, Ambient temp 45deg C . The operating CCT shall be 4000/5700K with CRI of ≥80. The luminaire shall be BIS Registered with electronic driver with input voltage range of 140 to 280V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs luminaire Life with L70 Criteria. Shall have minimum surge protection of 2.5KV. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with Photo Biological Safety Standard. It should have Electrical class I insulation. Dimension: 183 X 113 X 65mm, Weight: 0.45Kg. Approved Make: Wipro LW07-141-XND-XX-G1 or equivalent in Trilux/LT/Regent

Ceiling Fan- 1200MM Al Blades, Aluminium Die Casted Top and Bottom with high quality copper motor RPM - 380, Air Delivery > 280 CMM

Exhaust Fan : 450 mm sweep Metal Body Copper motor

Installation of Lighting Fixtures

Installation, testing and commissioning of following pre-wired, LED fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Sub Head - IV- Cable Trays

Supplying and installing following size of perforated Hot Dipped,Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling/shaft with G.I. suspenders including G.I. bolts & nuts, etc. as required & approved by the Engineer Incharge. (Quantity shall be confirmed at site as per final layout/ route/ application etc. & to be executed accordingly.)

450 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

Sub Head -V - Data and TV points

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-11 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed steel / PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

TV antenna socket outlet

Telephone socket outlet

Socket for RJ 45 Jack for Cat - 6 Cable

Bell Push

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

Supply, erection, testing and commissioning of following tap off / splitter as per specification in 1.6mm thick CRCA sheet steel enclosure for CATV system.

4 way splitter box

Supplying and fixing of following sizes of Heavy duty class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Sub Head -VI- Ups

25kVA ( 3 Phase input & 3 Phase output) with 30 min backup

Supply, installation, testing & commissioning of UPS system comprising of 1 Nos. 5 kVA ( 1 Phase input & 1 Phase output) units . The UPS should be double conversion; online DSP Technology based IGBT Rectifier and inverter with 30 min backup. The UPS should have internally fitted with SNMP interface that will provide real time status information. The batteries should be sealed maintenance free The package shall include battery bank, stands, cables between UPS and battery bank, interconnecting links and related accessories as per specifications

5 kVA ( 1 Phase input & 1 Phase output) with 30 min backup

PART-II EXTERNAL ELECTRICAL

Sub-Head - I - HT Panel

HT VCB 3No's Panel Board

Supply,transporting,loading & testing (pre dispatch) of indoor type floor mounted metal clad, 11 KV VCB panel with 3No. VCBs(1 Incoming , 2 outgoings), totally enclosed & fully interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, motorised charged and electrical/manually operated (by default) breaker suitable for use on 11 KV, 3 Phase, 50Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated AL bus bars with PVC heat shrinkable sleeves of 630 Amps capacity suitable power pack of 24 volts D.C. breaker featured with mechanical ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 6 NO + 6 NC with computer compatible and equipped with following switchgears and accessories i/c connections suitable for 3 x 300 sq.mm. on incomer/outgoing breaker XLPE 11KV cable (cable entry from bottom as required per site)with suitable size cable end box, end termination with heat shrinkable jointing material, Electronic hooter suitable for 230 Volt operation etc. as required.(Note-Cost of end termination not included in this item),

Incomer

11 KV tripple pole vacuum circuit breaker horizontal draw out type horizontal isolation of rated current 630 Amps. 350 MVA and fitted with

Over current (50 to 200% adjustable),earth fault (20 to 80 % adjustable),Short circuit ,Master trip,T.C.S all micro processor based numerical relays with manually reset & LED indications for each function.

3 Number dual core, dual ratio current transformers 300/150/1-1 A class 5p10 for protection & class 0.5 for metering/indications having burden 5VA.

Epoxy cast resin,fixed type potential transformers of ratio 11 KV/ 110 volts,PT class 0.5 accuracy & 50VA burden with HT and LT fuses.PT must be drawout type and should not be mounted on the top of the panel.

Cable box suitable for 1No. three core 300 sqmm XLPE cables.

Following additional indicating lamps and push buttons for VCB

Indicating Lamps for the following;

Spring Charged-[Blue]

Trip Circuit Healthy-[White]

Push buttons for the followings,

Green for VCB ON

Red for VCB OFF.

Yellow for trip alarm cancellation.

Space heater with thermostat

Bus Bar

800A 3P Al. Bus Bar 11 KV,350 MVA, HT sleeved (PVC not applicable)

3 Nos. Outgoing Panel each with:-

Specifications shall be exactly similar to incoming panel except for the following:-

3 Number dual core, dual ratio current transformers 100/50/1-1A class 5p10 for protection & class 1.0 for metering/indications having burden 5VA.

Over current (50 to 200% adjustable),earth fault (20 to 80 % adjustable),Short circuit ,Master Triip,TCS all micro processor based numerical relays with manually reset & LED indications for each function.

Indicating Lights , Push buttons, Space heater with thermostat complete with all standard acessories for each outgoing.

Auxilaries protections for transformers

8 Way annunciator window -1No.

Recieving,installation,tecting and commissioning of power pack with 220 Volt AC input & 24Volt DC continuous output suitable for closing/ tripping/indication uitable for listed above, HT panel boards with 2 Nos. 12 Volts each maintenance free batteries of 26 AH (or as per manufacturer standards) each, charging unit, capacitor bank for emergency delivering for trip system complete with suitable capacity of Ammeter & Voltmeter i/c connections with 2.5 sq. mm FRLS insulated copper conductor cable etc. as required.- 1 job

HT Panel Described As Above

Sub-Head-II - Transformers

Supply, installation, testing and commissioning of 630kVA, 11/.433 volts Deta/Star, vector group DYN11, outdoor mounting, oil cooled, ONAN transformer with On Load Tap Changers (OLTC) having AVS relay and RTCC for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote manual operation of OLTC, suitable for incoming voltage variation of +5% to –15% in equal steps of 2.5 % to give a constant secondary voltagee. The transformer shall be provided with fittings, accessories, protection, first filing of oil etc. including Buchholz oil temperature alarm/trip protection in LV chamber complete as per specifications and as required. The transformer shall be provided with arrangement to terminate XLPE cable on HT side and to connect Aluminium Bus Duct /Cable on LT side, complete as required. The Transformers shall confirm to IS: 1180 Part-VI & IS 2026.The losses of the Transformer should be as per latest ECBC guideline.As per Latest IS:1180 & Transformer efficiency type -2.It should be compatible with IBMS in all respect .Necessary items as required to form part of transformer.

Sub-Head - III - H.T. CABLE LAYING & TERMINATIONS

(Cable Quantiities will be checked at site & got approved from Engineer In charege before procurement/ execution.)

H.T. Cable Laying & Terminations

(Cable Quantiities will be checked at site & got approved from Engineer In charege before procurement/ execution.)

Supplying, laying and fixing of the following sizes earthed amoured aluminium conductor XLPE power cable of 11 KV grade confirming to IS 7098(Part II) amended upto date of following sizes on existing cable tray as required.

3 x 240 Sq.mm

Supplying and making indoor cable end terminations with heat shrinkable jointing kit complete with all accessories including lux suitable for following size of 3 core XLPE AL conductor cable of 11 KV grade as required.

Sub Head - IV -Main LT Panels

NOTE: All panel shall be completely modular and compartmentalized with Form 4B Separation as per IEC 61439. The panel shall be free standing floor mounted type . The panel shall be TTA and shall be manufactured as per IEC 61439.

Main LT cum Synchronization panel (TTA PANEL)

Supply, installation, testing and commissioning of dust, damp and vermin proof cubicle free floor, indoor type factory built sheet steel enclosed modular bolted construction extendable MAIN LT PANEL CUM SYN. PANEL, suitable for operation on 415 ± 10% volts, 50 Hz AC 3 phase 4 wire supply system fabricated out of suitable sized square tubular section and covered with CRCA sheet steel of 2.5mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having extensible type TPN Aluminium bus bars of high conductivity, SMC bus bar supports, with bottom base channel of section not less than ISMC 75mm, fabrication shall be done in transportable sections, entire panel shall have a common G.I. earth bus bar to switch gears with required size of Alum. bus bars and inter-connection with solid copper conductor wires / aluminium strips, neutral links, including control wiring with 1.5 / 2.5sqmm. PVC insulated FRLS copper conductor Single Core cable, cable alleys, cable gland plates in two half, etc.

necessary metering protections & indications and mounted with the following switch gears as per drawing and technical specifications etc. complete as required. Incoming & outgoing bus ducts/ cables will be from bottom & top both sides as per site requirement. Proper heat dissipation system should be provided in the panel. Panel should have converter from Modbus to Ethernet for energy meters etc. complete as required.

Section- 1

Incomers:

1000 Amp. 4 Pole ACB - 1 set (For DG)

1000 Amp. 4 Pole ACB - 1 set (For Transformer supply)

Air Circuit Breaker Horizontal drawout type of fault breaking capacity 50KA (Ics=lcu=Icw) Electrical Draw Out Motorized operated, fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/ test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with Independent Electrical & manual spring closing mechanism, Microprocessor release (EMI & EMC certified) for over current, earth fault & short circuit protection, Shunt trip coil 24V D.C / 220V A.C, Breaker Control Switch - 16A, Test terminal block set, circuits as per standard practice, auxiliary contactors with contacts (minimum 4NO+4NC) for positive interlocking of the breakers, necessary interlocking with PLC auto controls etc. as required including following accessories and suitable to receive bus duct/cable connections.

Metering, indications and protections for each incomer:

a) LED indication lamps for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy etc with 2Amp control MCBs

b) Set of Digital flush type multifunction meters (with RS485 port) 0- 1000A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 1000/5 Amp ratio, 15 VA Class 0.5 metering.(for DG)

c) Set of Digital flush type multifunction meters (with RS485 port) 0- 1000A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 1000/5 Amp ratio, 15 VA Class 0.5 metering.(for transformer)

d) Under voltage/ Overvoltage with definite time relay & master trip relays - 1 set for Transformer incomer & Master trip relays - 1 set for DG incomer.

e) Suitable size & nos of CT's for all protection relays (class 5P10, 15VA) & APFC Relay (class 0.5, 15VA) as per drawings

f) Surge Protection Device of type 1+ 2 of 25KA.

Bus Bar :

TPN aluminium extensible type main bus bars of minimum of 1250 Amps. capacity & auxiliary Bus Bars of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50ka capacity.

Outgoings:

1 No. - 630 Amp. 35ka three pole microprocessor release, MDO ACB (Ics=lcu=Icw) with O/L, S/C & earth fault protection. (Capacitor)

2 Nos. - 315 Amp. 35ka FP microprocessor release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare)

3 Nos. - 200 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare)

3 Nos. - 160 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection.

5 Nos. - 100 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare)

Each outgoing breaker shall have the following accessories-

a) 1 No. - 96 sq.mm. flush pattern digital type multifunction meter (with RS485 port) showing V, A, PF, Hz, KW, KWH, KVAR, etc. with three nos. cast resin suitable rating of CT's, class 0.5 accuracy & 15 VA burden, protection MCB's etc.

b) LED indication lamps with 2Amp back up control MCB for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy, test terminal block set, circuits as per standard practice etc. as required for all ACB's.

c) Extended rotary operating mechanism, terminal extension spreaders, LED indication lamps with 2Amp control MCB for breaker 'ON/OFF' for all MCCB's.

Bus Coupler

1 No. 1000 Amps, 50 KA, 440 volt 4-P EDO ACB without release complete with following:

6 Nos. NO/NC contacts for remote opening & closing

Red/Green / Amber / ON/OFF / Trip indicating lamps with 2A SP MCB as backup protection.

Backup MCB and terminal blocks as required.

TNC Breaker Control switch

Required Operation / Interlocking with other incomers & Bus Coupler to be provided as per Interlocking / operation scheme indicated in Drawing No. - Operation / Interlocking shall be through micro PLC.

Section- 2

800 Amp. 4 Pole ACB - 1 set (For DG)

1000 Amp. 4 Pole ACB - 1 set (For Transformer supply)

Air Circuit Breaker Horizontal drawout type of fault breaking capacity 50KA (Ics=lcu=Icw) Electrical Draw Out Motorized operated, fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/ test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with Independent Electrical & manual spring closing mechanism, Microprocessor release (EMI & EMC certified) for over current, earth fault & short circuit protection, Shunt trip coil 24V D.C / 220V A.C, Breaker Control Switch - 16A, Test terminal block set, circuits as per standard practice, auxiliary contactors with contacts (minimum 4NO+4NC) for positive interlocking of the breakers, necessary interlocking with PLC auto controls etc. as required including following accessories and suitable to receive bus duct/cable connections.

Metering, indications and protections for each incomer:

a) LED indication lamps for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy etc with 2Amp control MCBs

b) Set of Digital flush type multifunction meters (with RS485 port) 0- 800A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 800/5 Amp ratio, 15 VA Class 0.5 metering.(for DG)

c) Set of Digital flush type multifunction meters (with RS485 port) 0- 2000A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 1000/5 Amp ratio, 15 VA Class 0.5 metering.(for transformer)

d) Under voltage/ Overvoltage with definite time relay & master trip relays - 1 set for Transformer incomer & Master trip relays - 1 set for DG incomer.

e) Suitable size & nos of CT's for all protection relays (class 5P10, 15VA) & APFC Relay (class 0.5, 15VA) as per drawings

f) Surge Protection Device of type 1+ 2 of 25KA.

Bus Bar :

TPN aluminium extensible type main bus bars of minimum of 1250 Amps. capacity & auxiliary Bus Bars of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50ka capacity.

Outgoings:

1 No. - 630 Amp. 35ka three pole microprocessor release, MDO ACB (Ics=lcu=Icw) with O/L, S/C & earth fault protection. (Capacitor)

2 Nos. - 315 Amp. 35ka FP microprocessor release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare)

2 Nos. - 200 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare)

3 Nos. - 160 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection.

1 Nos. - 125 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection.

4 Nos. - 100 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare)

1 Nos. - 63 Amp. 35ka FP thermal based release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare)

Each outgoing breaker shall have the following accessories-

a) 1 No. - 96 sq.mm. flush pattern digital type multifunction meter (with RS485 port) showing V, A, PF, Hz, KW, KWH, KVAR, etc. and three nos. cast resin suitable rating of CT's, class 0.5 accuracy & 15 VA burden, protection MCB's etc.

b) LED indication lamps with 2Amp back up control MCB for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy, test terminal block set, circuits as per standard practice etc. as required for all ACB's.

c) Extended rotary operating mechanism, terminal extension spreaders, LED indication lamps with 2Amp control MCB for breaker 'ON/OFF' for all MCCB's.

PLC BASED AUTO SYNCHRONISING, AUTO LOAD TRANSFER, AUTO LOAD SHARING, AUTO LOAD BALANCING PANEL HAVING FACILITY FOR 2 NO DG's (1Nos. 600KVA + 1Nos. 500KVA) & 2 TRANSFORMER (2nos. 630 kva each).

Design, manufacturing, testing at site, handling, assembling, installing in correct assigned position, effecting proper connections, testing and commissioning of PCC 3300/ PLC based Auto Synchronising panel.

1 No. analog Double voltmeter 0-500V, (144 sq.mm.)

1 No. Double frequency meter (415V/110V) (144 sq.mm.) reed type.

1 No. Synchroscope, 110 V (144 sq.mm.) Analog.

2 nos. 110 V AC dark lamps.

4 Nos. under voltage monitors.

1 No. synchronising switch

1 No. Manual/Auto switch.

Push buttons for Test, Accept, Reset, Fault Reset, Engine Start, Engine stop, ACB close, ACB Trip Emergency stop.

8 Nos. Joysticks for voltage raise/ lower and speed raise/ lower.

4 Nos. manual/ auto AMF toggle switch.

8Nos. 24V DC semaphone, 38 mm.

PLC Hardware as required and as per specifications.

Auxiliary relays as required and as per specifications.

1 No. check synchronising relay, 110 V AC 50 Hz.

230V AC/24V DC, 10A, stabilized power supply with voltage trimmer and maintenance free battery.

Annunciators as required and as per specifications.

16 Window annunciation panel (for each D.G. Set) for following indications/ alarms :

Set fails to start

Engine overheat.

Excitation failure.

High temperature

Low Lube oil pressure.

Over speed

Low fuel oil level

Cooling water flow failure

Breaker Trip

Generator fault.

DC control supply failure.

Voltage out of limits.

Spares.

Necessary interlocking/ controlling with PLC auto controls i/c PLC hardwares & software etc. complete as required.

Main LT cum Synchronization panel described as above & as per drawing.

Capacitor Panel - 215 KVAr

Supply, installation, testing and commissioning of dust, damp and vermin proof cubicle free floor, indoor type factory built sheet steel enclosed modular bolted construction extendable APFC panel comprising of 215KVAR with heavy duty capacitors units in a bank formation to achieve Automatic operation. suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire supply system fabricated out of Form 4b compartmentalized design and covered with CRCA sheet steel of 2mm thick for frame work and 1.6mm thick for doors/ covers, i/c cleaning & finishing complete with 9 tank process for powder coating in approved shade, TP Aluminium bus bars of high conductivity, DMC/SMC bus bar supports, with short circuit with stand capacity of 50KA for 1 sec., bottom base channel of section not less than ISMC 75mm, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of suitable size with 2 nos earth studs, including control wiring with 1.5sqmm. PVC insulated FRLS copper conductor Single Core cable for voltage & 2.5sq.mm for current circuits, danger notice plates, etc. necessary metering protections & indications and mounted with the following switch gears as per drawing and technical specifications etc. complete as required.

Incomer:

1 No. - 630 Amp. 50ka FP pole microprocessor release, MDO ACB (Ics=lcu=Icw) with O/L, S/C & modular earth fault protection.

Suitable cubicle size for cables in bus bar

1 Set of three phase R,Y,B indicating lamps along with 2A SP control MCB backup protection.

Control MCB'S, control terminals & wiring as required.

Required nos of summation CTs of suitable rating for interlocking with Transformer incomers

Automatic P.F.C.R. 7 stage with power factor meter & CT's for unbalanced load - 1 Set.

Busbar :

TP aluminium extensible type main bus bars of minimum of 800 Amps. capacity & auxiliary Bus Bars of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 35ka capacity.

Outgoings :- Control MCB/ MCCBs with capacitor banks:

125Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 50 KVAr, 415V (fixed) Heavy duty capacitor bank etc. - 1 set.

125Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 50 KVAr, 415V Heavy duty capacitor bank etc. - 2 set.

63Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 25 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 2 sets.

40Amp. TP MCCB '10ka' Thermal Magnetic release having O/L & S/C protection with 10 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 1 sets.

32Amp. TP MCB '10ka' Thermal Magnetic release having O/L & S/C protection with 5 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 1 sets.

Capacitor Panel as above

Automatic Fire Suppression System:

Supply, fixing, testing and commissioning of automatic Linear pneumatic tube detection based 3M Novec 1230 System for Electrical Panels (Linear pneumatic Heat Detection Tube Panel Protection System), consisting of the Mentioned components

5.0 LB Capacity 3M Novec-1230, DLP Assembly with automatic valve DOT Approved Cylinder, push in connector for tube, 5.0 LB 3M Novec 1230 Fluid, Mounting bracket, End of Line Adopter and low pressure switch for monitoring system activation

Providing Flexible Linear Pneumatic Heat Detection Tube (4/6mm Dia. Operated At 100 Degree Centigrade, Colour Code-Red) UL Listed For Automatic Fire Detection & Suppression System Made By Special Modified Polymide High Grade Quality complete with Slip-on Push-in Tube Fittings such as Straight Connector, Tee Connector, End of Line Plug as required

Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The control panel should have provision of integration with fire Alarm / SCAD/ BMS system.

Residence Building Panel

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 63 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 100 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

63A FP MCB '16kA' - 8nos. (2 No. Spare)

40A DP MCB '10kA' - 7nos. (1 No. Spare)

Panel describe as above

Stilt Floor Panel

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 160 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 100 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

100A FP MCCB '25kA' - 2nos. (1No. Spare)

63A FP MCB '16kA' - 5nos. (1No. Spare)

40A DP MCB '10kA' - 1No. Spare

Panel describe as above

Ground Floor Panel

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 315 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 400 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

100A FP MCCB '25kA' - 2nos. Spare

63A FP MCB '16kA' - 8nos. (1No. Spare)

40A DP MCB '10kA' - 1No. Spare

Panel describe as above

1st Floor Panel

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 200 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 315 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

63A FP MCCB '25kA' - 2nos. (1No. Spare)

63A FP MCB '16kA' - 5nos. (1No. Spare)

40A DP MCB '10kA' - 1No. Spare

Panel describe as above

2nd Floor Panel (2nd to 6th Typical)

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 160 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 100 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

63A FP MCCB '25kA' - 2nos. (1No. Spare)

63A FP MCB '16kA' - 5nos. (1No. Spare)

40A DP MCB '10kA' - 1No. Spare

Panel describe as above

Terrace Floor Panel

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 100 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 125 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

63A FP MCCB '25kA' - 2nos. (1No. Spare)

63A FP MCB '16kA' - 3nos. (1No. Spare)

40A DP MCB '10kA' - 1No. Spare

Panel describe as above

UPS PANEL

UPS Input Panel

Incoming:

1 No. of 100 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating Lamp with 2A SP MCB back-up.

Metering

Minimum 96 mm square pattern flush mounting digital type multi function meter for A, V readings, scaled suitably with required CT's.

1 Set of phase indicating lamp with 2Amps SP MCB back-up.

Bus Bars:

125 Amp.25 Ka, Al. Bus Bar

Outgoing:-

All outgoing feeders shall be provided with On indicating lamp with 2 A SP MCB protection.

100A FP MCCB - 4 Nos.

UPS Output Panel

Incoming:

3 No. of 100 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating Lamp with 2A SP MCB back-up.

Metering

Minimum 96 mm square pattern flush mounting digital type multi function meter for A, V readings, scaled suitably with required CT's.

1 Set of phase indicating lamp with 2Amps SP MCB back-up.

Bus Bars:

125 Amp.25 Ka, Al. Bus Bar

Outgoing:-

All outgoing feeders shall be provided with On indicating lamp with 2 A SP MCB protection.

63A FP MCCB - 1 Nos. spare

63A FP MCB - 5 Nos. (1nos. Spare)

40A DP MCB - 17 Nos. (1nos. Spare)

Panel Described as above.

Lift Panel (2nos. Lift)

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

i) 1 No. - 100 amps four pole MCCB (25 KA) with following accessories:

a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB

b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 100/ 5 Amp ratio, 15 VA Class 0.5 metering.

Bus Bar :

4P aluminium extensible type main bus bars of minimum of 125 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete.

Outgoings:

3 Nos. - 63 Amp. MCB four pole (10kA) (1 Nos. Spare)

3 Nos. - 40 Amp. MCB four pole (10kA) (1 Nos. Spare)

1 No. - 32 Amp. MCB DP (10kA) MCB

Each outgoing breaker shall have the following accessories-

a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's.

Lift Panel described as above

EV Car and Byke Charging Panel (Stilt Floor)

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 100 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 125 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

32A FP MCB '10kA' - 12nos. (1No. Spare)

25A DP MCB '10kA' - 13nos. (1No. Spare)

Panel describe as above

EV Car and Byke Charging Panel (1st Floor)

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 63 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 100 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

32A FP MCB '10kA' - 7nos. (1No. Spare)

Panel describe as above

EV Car and Byke Charging Panel (2nd Floor till Terrace)

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No. of 100 Amp 4P MCCB of 35 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up.

Bus Bars:

Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 125 amps, 35kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints.

Outgoing:

32A FP MCB '10kA' - 13nos. (1No. Spare)

Panel describe as above

Sub Head- V- LT Cables

Supply, laying, testing and commissioning of 1.1 kv grade XLPE insulated PVC sheathed steel armoured alluminium stranded conductor ISI marked LT Cables in trenches/ ducts/ through RCC pipes under roads/ on cable trays of following sizes, complete all as specified (as per CPWD specifications for External Electrical works), i/c clamping, dressing, earth work digging, sand filling, bricks protection, back filling etc. as required & approved by Engineer's Incharge. (Tagging to be provided with aluminium strips on both the ends as approved).

3½ core X 300 Sq.mm.

3½ core X 240 Sq.mm.

3½ core X 185 Sq.mm.

3½ core X 150 Sq.mm.

3½ core X 120 Sq.mm.

3½ core X 95 Sq.mm.

3½ core X 70 Sq.mm.

3½ core X 50 Sq.mm.

3½ core X 35 Sq.mm.

3 core X 10 Sq.mm

3 core X 6 Sq.mm

4 core X 25 Sq.mm

4 core X 16 Sq.mm

4 core X 10 Sq.mm

4 core X 6 Sq.mm

Supplying and making cable end termination with brass compression glands and aluminium lugs including inhibiting compound to be used in each lug, for the following XLPE aluminium conductor armoured cables of 1.1 KV grade etc, complete as required.

3 core X 6 Sq.mm

4 core X 6 Sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Sub Head - VI- Cable Tray

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

900 mm width X 62.5 mm depth X 2.0 mm thickness

Sub-Head - VII - Earthing

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing, laying, fixing, connecting and testing of undernoted sizes of copper strip/ GI strip/ wire from earth electrode to equipment loop and earthing system, in trenches, on surfaces, along pole or along M.S. support, etc. including excavation where required for laying the copper strip/ GI strip and filling back complete, conforming to relevant IS and all as specified.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Sub-Head - VIII - External Lighting

External Lighting Panel

Supply, assembly, erection, connecting, testing & commissioning of LT weather proof dust and vermin proof, outdoor feeder pillar, fabricated out of suitable sized angle iron and flats and covered with 3mm thick CRCA sheet steel including canopy, duly stove enamel painted, both sides (front and rear) openable with locking arrangement, rubber gasket cable glands, etc. Bakelite phase separators and bus bar supports including RCC 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) foundation, 450 mm deep and 150 mm above the ground. The feeder pillars shall be complete with 3 phase and neutral bus bars of capacities as described below and moulded case circuit breakers (MCCBs) with adjustable overload relay, copper FRLS control wiring with 1.5sq.mm, complete in all respects as per specifications as required.

INCOMING:-

63A 4P MCCB (25ka) with thermal magnetic release & rotary handle - 1no.

3 Phase and neutral (100%N) aluminium bus bars of 150/ 100 amps. Capacity.

OUTGOING:-

70 AMP. TP CONTACTOR WITH NO/ NC CONTACTS -1 set.

24 HOUR TIMER - 1 set.

25A 4P MCB (10ka) - 2 nos.

16A DP MCB (10ka) - 5 nos.

63A 4P MCB (10ka) - 3 no.

16 AMP. SWITCH & SOCKET - 1 no. with in the feeder pillar.

External Lighting Feeder Pillar as above

Supply of LED street light fitting not more than 100W having System Efficacy >120 lm/W, system output >=12000 Lumens, THD <10% @ full load, Power Factor >0.95 @ full load, power factor >0.9 @half load, SDCM<5, CRI >70, CCT 5700, L70B50 lifetime of 50,000hrs @ 35deg C ambient temperature. Full IP 66 ( with out Glue) protected single piece die cast aluminium housing having PC window with Impact resistance IK10. Luminaire operating voltage should lie between 150-300V AC. Luminiare should be suitable for Pole dia of 30-40mm. LED driver should be Potted & Encapsulated. Fixture should have BIS compliance. Driver shall have 6KV Surge protection and 10KV should be housed inside the Luminiare ( Bolted one). Ambient temp range: 0deg to 45deg C. It will be connected with 3C 1.0sq.mm,0.5m-flying cable for interface to Mains. It should meet all international Quality standards IEC60598. Similar to Wipro LR08-112-XXX-57-ML

Supply, Installation, Testing and Commissioning of 9.0 Mtr. long G.I. Octagonal with Single arm, pole shall be fabricated with following dia pipes 155 mm x 3.0 mm (Bottom) and 70 mm x 3.0 mm (top) with a bottom plate of size 260x260x16mm having necessary gusset plate etc. with 1 Nos. 1.0 Mtr. long arm as per light fixture or proper provision to mount 1 nos. street light fixtures, including Concrete Foundation of size 350 x 350 x 1000 mm in precast RCC block with 4 nos. "J" hook (Bolt) of 24 mm dia and length 750 mm. complete with Nut & washer. The foundation shall be completes with all respect including finishing and Earthing is required. as per specification including excavation, wiring with 3Cx2.5 sq.mm copper wire from the integral control box to street light fixture with four number 20A copper bus bar along with supports of suitable size, 1 no 10A MCB, neutral link & connection to the lamp through the pole, connection to the integral control box through the concrete foundation with suitable size G.I. Pipes & painting with two coats of primer & two coats of enamel paint as required. Make: Wipro

Supply of LED Post Top with a system lumen output of 4500 lumens and a minimum system efficacy of >100 lm/W. The luminaire shall have a rated system lifetime of >50,000 burning hours at L70. The luminaire should have a color temperature of 4000K/5700K and CRI > 70. The luminaire shall meet IP66 and IK07 with THD < 10% at full load and PF > 0.95. The total power consumption should not exceed 45W (including driver). Surge Protection of 4KV is provided. The driver and fixture should be BIS approved. The fixture should comply with the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Dimension: Ø336 X 370mm & Weight including all accessories should not be more than 2.2Kg. Similar to Wipro LP09-501-XXX-57-ML

SITC of 4.0 mtr Al step tubular pole, Pole should have Anti rust coating & should be PU Painted, 4 nos of foundation nut & bolt(16mm dia & 600 mm long with templates) with a base plate of 250mmx250mm, Base Plate thickness- 15 mm. Pole Thickness-3.0mm. Pole Base OD up to 1 mtr -1.2 mtr of 102mm dia, then 6 mm OD Pole should have a din rail for MCB mounting provision with Bakelite sheet and 32 mm Electrical Connector with Bubble sheet Packing suitable for BOQ complete as required. Make: Wipro

Supply of LED based Spike light, housing made up of pressure die cast aluminum Alloy with effective thermal management,sturdiness and embossed brand name/logo name of manufacturer and optics made of surface mount reflector with toughened. The fixture should have a minimum system efficacy of 80lumen/Watt and a minimum system lumen output of 640 lumens and maximum system wattage of 8 Watts.The fixture shall have a CRI of minimum 80 and beam angle: 50-55deg. The fixture shall be designed for a system life of 50,000 hours @70% lumen maintenance. Ingress Protection of IP67 (lamp and gear Compartment) and Mechanical Impact Resistance Rating of IK >=07, CCT: 2700K. The fixture driver should have an operating voltage range of 100-270 V, surge protection of >=3KV, PF >0.9, THD<10% & Driver efficacy >80% @full load and rated voltage. Ambient temp range: 0deg to 45deg C. The Drivers should be a potted driver not a printed circuit board without casing, mounted inside the luminaire. The fixture should comply with the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL . LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Dimension: Ø115 X 158 X 93mm & Weight including all accessories should not be more than 1.5Kg. Similar to Wipro LF05-600-055-27-ML

Supply of LED based bollard, housing made up of extruded aluminium,sturdy and embossed brand name/logo name of manufacturer and optics made of PC diffuser. The fixture should have a minimum system efficacy of 80lumen/Watt and a minimum system lumen output of 880 lumens and maximum system wattage of 11Watts.The fixture shall have a CRI of minimum 80. The fixture shall be designed for a system life of 50,000 hours @70% lumen maintenance. Ingress Protection of IP65 (lamp and gear Compartment) and Mechanical Impact Resistance Rating of IK >=08, CCT: 4000K. The fixture driver should have an operating voltage range of 100-270 V, surge protection of >=3KV, PF >0.9, THD<10% & Driver efficacy >80% @full load and rated voltage. Ambient temp range: 0deg to 45deg C. The Drivers should be a potted driver not a printed circuit board without casing, mounted inside the luminaire. The fixture should comply with the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL . LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Height: 800mm & Weight including all accessories should not be more than 0.95Kg. Similar to Wipro LB16-131-X40-08-X5

Supplying and drawing following sizes of PVC insulated PVC sheathed copper conductor unarmoured multicore cable in the existing poles and bracket from cable termination connector to the fitting i/c providing suitable copper lugs connections etc. as reqd.

3 core 1.5 sq.mm.

Supply of following size of 1.1KV grade multicore aluminium conductor XLPE insulated and PVC sheathed armoured cable in existing trenches/ hume pipe/in ground as per IS : 7098:1988 with upto date amendments.

4c x 16 sq.mm

4c x 10 sq.mm

3c x 6 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 core X 16 Sq.mm

4 core X 10 Sq.mm

3 X 6 sq. mm (19mm)

Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Sub-Head -IX :- Miscellaneous

Supply and fixing in position 1000mm wide checkered rubber matting of 11KV grade as per electricity rules,with thickness not less than 12mm.

Supply and fixing in position the best quality L.T. Danger Notice plate of 200mm x 150mm,made of mild steel atleast 2mm thick and vitreous enamelled, white on both sides and with inscription in signal red colour on front side written in English & Hindi as required.

Supply and fixing in position the best quality H.T. Danger Notice plate of 250mm x 200mm made of mild steel atleast 2mm thick and vitreous enamelled, white on both sides and with inscription in signal red colour on front side written in English & Hindi as required.

Supply and fixing in position the approved shock treatment / restoration charts written in Hindi and English duly framed in teak wood frame and covered with 2.8mm glass as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

6C X 1.5 sqmm

Supplying and fixing of fire buckets 5 Nos.in each set of approved quality, red painted from outside and white from inside conforming to IS : 2546/1974 with additional handle at the bottom, filled with fine sand and fixed on an angle iron frame as per the requirement of local authorities.

Supplying and fixing of MS pedestal stand suitable for supporting four buckets as required.

Supplying and fixing First Aid Box of 18 S.W.G. M.S sheet,painted as approved & prescribed by Indian Red Cross Society & as per attached specifications.

Supplying and fixing of caution Boards of 16 S.W.G. , M.S. sheet of 300 mm x 150mm size, duly painted & having "MAN ON LINE' & "DO NOT SWITCH ON' written in Red complete with hanging arrangement as required.

Supply and fixing in position the approved single line diagram framed in 1000 x 800 mm size glass framed and installed in main switch room.

Supply of tool kit with 1 pair,11KV rubber hand gloves of aproved make.

Supply and fixing of Insecticuters for Kitchen.

Installation of Air Curtain

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required

100 mm dia pipe

150 mm dia pipe

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

100 mm dia ID

150 mm dia ID

300 mm dia pipe

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required

90 mm dia (OD-90 mm & ID-76 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

160 mm dia (OD-160 mm & ID-135 mm nominal)

200 mm dia (OD-200 mm & ID-175 mm nominal)

PART-III D.G SET

Sub-Head - I - DG Set

650KVA DG

Supply, transporting, loading, unloading, erecting, testing and commissionig etc. of Silent Type Diesel Generating Set of 650KVA, 3 phase & neutral, 50 c/s. 415 A.C. rating, comprising of following Diesel Engine, Alternator, Sound Attenuated Acoustic Enclosure, including necessary RCC foundation for errection including earth work as required and with other associated accessories:

Diesel Engine

Diesel engine 4 stroke Rwater cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 50 Degree C, 50%RH & at 1000 Meter MSL and conforming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for one hour included in 12 hours of continuous operation. The engine will be fitted complete with all the required accessories

Engine mounted Instrument Panel fitted with and having digital display for following:

Start-Stop switch with push button

Water temperature indication

Lubrication Oil pressure indication

Battery charging indication

RPM indication

Over speed indication

Engine Hours indication

Digital electronic governor/digital voltage regulator

Battery monitoring system & weak battery warning

Digital metering for current, voltage, PF, KWH, KVA

Alternator protection for under/over voltage, under/over frequency, reverse power, over current.

Alternator:

Alternator rated at 600KVA, 415 volts at 1500 RPM, 3 phase 50 HZ, AC supply with 0.8 lagging power factor at 50 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty self excited and self-regulated through AVR conforming to IS :4722/BS 2613 suitable for tropical condition and ambient temperature at 50 Degree C and as per manufacturer's standard specifications with class-H insulation.

Auto Start/Auto load management should be through controller type 3300 or approved equipment.

with suitable Breaker

Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary PCC block of 1:1.5:3 ratio of cement concrete of depth of 300 mm with suitable reinforcement which shall be installed on existing hard concrete floor and vibration isolation arrangement as per recommendation of manufacturer.

Exhaust System:

Dry exhaust manifold of suitable dia, welded blank MS pipe confirming to IS:3589 cut to required lengths (max. 2 mtrs) and installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with 50mm thick mineral wool/Rockwool, wire mesh and aluminium cladding 0.8 mm thick etc. as required as per specifications with hospital exhaust silencer.

Starting System:

24V DC Starting system comprising of starter motors: Voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (2 Nos. of 180 Amp. Hour capacity maintenance free ) as required as per specifications.

Fuel Tank:

Daily service fuel tank of 990 liters capacity fabricated out of 3 mm thick MS sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS Class C pipe of suitable dia complete with valves, level indication, flow switch with potential free contacts for giving signal to existing BMS system and accessories as required as per specifications.

D.G Set Describe as above

500KVA DG

Supply, transporting, loading, unloading, erecting, testing and commissionig etc. of Silent Type Diesel Generating Set of 500KVA, 3 phase & neutral, 50 c/s. 415 A.C. rating, comprising of following Diesel Engine, Alternator, Sound Attenuated Acoustic Enclosure, including necessary RCC foundation for errection including earth work as required and with other associated accessories:

Diesel Engine

Diesel engine 4 stroke Rwater cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 50 Degree C, 50%RH & at 1000 Meter MSL and conforming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for one hour included in 12 hours of continuous operation. The engine will be fitted complete with all the required accessories

Engine mounted Instrument Panel fitted with and having digital display for following:

Start-Stop switch with push button

Water temperature indication

Lubrication Oil pressure indication

Battery charging indication

RPM indication

Over speed indication

Engine Hours indication

Digital electronic governor/digital voltage regulator

Battery monitoring system & weak battery warning

Digital metering for current, voltage, PF, KWH, KVA

Alternator protection for under/over voltage, under/over frequency, reverse power, over current.

Alternator:

Alternator rated at 500KVA, 415 volts at 1500 RPM, 3 phase 50 HZ, AC supply with 0.8 lagging power factor at 50 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty self excited and self-regulated through AVR conforming to IS :4722/BS 2613 suitable for tropical condition and ambient temperature at 50 Degree C and as per manufacturer's standard specifications with class-H insulation.

Auto Start/Auto load management should be through controller type 3300 or approved equipment.

with suitable Breaker

Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary PCC block of 1:1.5:3 ratio of cement concrete of depth of 300 mm with suitable reinforcement which shall be installed on existing hard concrete floor and vibration isolation arrangement as per recommendation of manufacturer.

Exhaust System:

Dry exhaust manifold of suitable dia, welded blank MS pipe confirming to IS:3589 cut to required lengths (max. 2 mtrs) and installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with 50mm thick mineral wool/Rockwool, wire mesh and aluminium cladding 0.8 mm thick etc. as required as per specifications with hospital exhaust silencer.

Starting System:

24V DC Starting system comprising of starter motors: Voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (2 Nos. of 180 Amp. Hour capacity maintenance free ) as required as per specifications.

Fuel Tank:

Daily service fuel tank of 990 liters capacity fabricated out of 3 mm thick MS sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS Class C pipe of suitable dia complete with valves, level indication, flow switch with potential free contacts for giving signal to existing BMS system and accessories as required as per specifications.

D.G Set Describe as above

INSTALLATION OF D. G. SET :

Receiving, unloading, shifting, assembling, placing at foundation, installation, testing and commissioning of DG Sets as mentioned in subhead I. The item rate shall include the cost of initial fill of lube oil ( First fill of Lube oil only)

600 kVA with acoustic enclosure as described above complete in all respect.

500 kVA with acoustic enclosure as described above complete in all respect.

The item rate shall include the cost of diesel for 8 Hrs. Testing at project site.

Sub-Head-II: D.G. Set Associated Works: Low Side Work

Exhaust

Exhaust Piping Work :

Design, manufacture, supply, erection, testing & commissioning of B Class DG exhaust piping of following size suitable for above mention DG sets including Anti vibration mounting arrangement ,Structural load support, Steel bracket including foundation ,foundation bolts to avoid any load and stress on turbo charger/exhaust pipe , supports for maintenance . This structure shall be designed as per prevaling indian standard for earthquake , wind velocity, gravity loads,temperature loads at site. Item Include welding, cutting and fixing of require acessories , 2 layers of anti-coating primer with 2 layers of silver paint etc whereever require .exhauts piping work include the insulation of silencer & exhaust pipe with rain trap to avoid rain water entry in pipe & inspection spout at suitable location.The grade of pipe/class should be suitable to relevant latest applicable code in addition to technical specifcation & CPCB. These are the minimum requirements , work should be completed in line requirements of DG manufacturer recommendation as per site requirement ,Complete in all resepct as :- .

Supply, erection, testing and commissioning of MS exhaust piping horizontal run as per IS 3589& 1239 of following sizes with welding joint including bends, MS pipe, clamps, dash fastener, nuts, bolts etc. with insulation by applying MAS-17 adhesive then a layer of minimum 75 mm thick rockwool (150Kg/Cub Mtr.) covered with 24 SWG aluminium sheet claddings etc. complete as required and as per specifications.

200 mm dia NB (4.85mm Thickness)

Supply, erection, testing and commissioning of MS exhaust piping vertical run as per IS 3589& 1239 of following sizes with welding joint including bends, MS pipe, clamps, dash fastener, nuts, bolts etc. with insulation by applying MAS-17 adhesive then first layer of insulation 25mm thick ceramic fibre wool (96Kg/Cub. Mtr.) & second layer minimum 100mm thick rockwool(150Kg/Cub Mtr.) covered with 24 SWG aluminium sheet claddings etc. complete as required and as per specifications.

200 mm dia NB (4.85mm Thickness)

Supply & Fixing of SS expansion joints for horizontal/ vertical exhaust pipes as required at site:

150mm exhaust SS Bellow

Supply, erection, testing and commissioning of insulation by applying MAS-17 adhesive then layer of minimum 100mm thick rockwool(150Kg/Cub Mtr.) covered with 24 SWG aluminium sheet claddings etc. complete as required on silencer and as per specifications. Note : Silencer shall be part of standard supply with DG Set.

For 600 KVA DG Set

For 500 KVA DG Set

APPROVAL OF STATUTORY AUTHORITY: Preparation of drawings/documents in required sets to be submitted to statutory authority, obtaining approval/permission of electrical installation for operation of DG Sets as standby source, including Liasioning with Electrical Inspector/Local Supply Authority/Pollution Control Board etc. complete as required.

PART-V - LIGHTNING ARRESTER

Air Termination Network

Supply of single spike air terminals of 10 mm dia. & 1000 mm length as required and as per site conditions. The air terminal shall be manufactured with aluminium & shall be as per IEC 62561-2. The air terminal shall be fixed with clamping arrangement (MV Clamp) Make: JMV

Supply of single spike air terminals of 10/16 mm dia. & 2000 mm length as required and as per site conditions. The air terminal shall be manufactured with aluminium & shall be as per IEC 62561-2. The air terminal shall be fixed with base plate arrangement. Make: JMV

Roof Conductor for Parapet & Mesh: Supply of 8 mm dia aluminium round conductor for air termination network at parapet and for making mesh at terrace level and shall meet the requirement of IEC 62561-2. Make: JMV

Supply of Parapet Conductor holder for holding of 8 mm dia. round conductor (for RCC roof). The conductor holder shall be mounted on plastic base support and shall meet the requirements of IEC 62561-4.It should be installed at every 1 mtr. Make: JMV NOTE-Holder can be Change as per Site Condition

Supply of Mesh Conductor holder for holding of 8 mm dia. round conductor (for RCC roof). The conductor holder shall be fixed on plastic support weighed by concrete block. It shall meet the requirements of IEC 62561-4 and should be installed at every 1 mtr. Make: JMV

Bridging cable: Supply of 16sq.mm. copper cable along with lugs, having 500mm length & as per IEC 62561-1 so as to connect air termination rod with any metallic structure on the roof. Make: JMV

Supply of Universal Connector for making straight, Tee & Cross joint of 8 mm Aluminium Conductor to 8 mm dia Aluminium conductor on parapet wall, roof and vertical facade of masonery / glass / metallic work. Make: JMV

Down Conductor

Supply of 8 mm dia aluminium round conductor for Down conductors to be installed on vertical wall, façade of masonary / glass / metalic work. It shall meet the requirements of IEC 62561-2. Make: JMV

Supply of Down Conductor holder for holding of 8 mm dia. round conductor (for RCC roof). The conductor holder shall be mounted on plastic base support and shall meet the requirements of IEC 62561-4.It should be installed at every 1 mtr. Make: JMV

Supply of Test Clamp to disconnect the 8mm down conductor from the earth termination network 8mm dia CBS Conductor for regular checks of the earth termination resistance value. (with enclosure). It shall meet the requirements of IEC 62561-2. Make: JMV

Supply of Expansion piece made of 8mm dia. Aluminium & as per IEC 62561-2 along with suitable connecting accessory. It shall be installed at every 20 mtr to maintain the flexibility to the conductor due to heat.

Supply of Lightning Strike counter Model: JMV 7D for counting the number of lightning strikes without any power supply. The Counter should be mounted on the Down Conductor. The Lightning Counter should be IP 68 rated enclosure suitable for external application.

Earth Termination Network

Supply of Earthing termination made of copper-bonded rod of 10 feet length,14.2 mm dia. (Minimum copper bonding shall be 0.25mm) as per IS 3043, IEEE-80, NBC 2016 along with 25 kg Earth enhancement material with resistivity of 0.12 ohm-mtr, and complying IEC 62561-7 and Pit Cover complying IEC 62561-5 and as per specification and other applicable codes.

Supply of 8 mm CBS Conductor laid at below the ground, as Required and as per specification and code of practice with Tee, L and Straight joint. Make: JMV

PART-V F.A.P.A

Sub Head - I- Fire Alarm System

Intelligent Fire Alarm System

10 Loop Panel

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Multi-Criteria Sensor (Smoke+Heat+CO) Features, Low profile - only 2" high, Simple and reliable device addressing, Supports 16 operational modes, Automatic compensation for sensor contamination , Built in Fire test feature, Two built-in power/alarm LEDs, programmable non-polling LEDs, Non-directional Smoke chamber, Vandal resistant security locking feature, 10 years CO sensor life span, Approved by LPCB.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supply, Installation, Testing & Commissioning of Analogue Addressable Single Input Monitor Module. which Includes a single monitored input, flying leads for easy installation. Electronically addressed, Approved by LPCB & Vds..

Supply, installing, testing and commissioning of Addressable Relay Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The Add Analogue Addressable Single Output Module . which Includes a single output, flying leads for easy installation. Electronically addressed, Approved by LPCB & Vds

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required

Supplying, installation, testing & commissioning of addressable phone control module complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supply, Installation, Testing and Commissioning of Addressable exit signage visible from 20 mtrs. with integral ba.Lery capacity of 2 hrs. and bicoloured LED status indicator.

One way/Two Way Exit Signage

Sub Head - II- Public Address System

Public Address System

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

speaker cable Single pair, 2-core, 1.5 sqmm

speaker cable Two pair, 2-core, 1.5 sqmm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia.

25mm dia.

Supply of Amplifier of 250 watts Output, Class D Type - Low Heat dissipation, Integrated with Main /Slave Consoles - with 2U Enclosure 19" Rack Mountable

Supplying, installation, testing & commissioning of 12URacks should be manufactured out of steel sheet punched, formed, welded and powder coated,Rack should have 100% assured compatibility with all equipment’s conforming to DIN 41494 (General Industrial Standard for equipment’s) or Equivalent EIA /ISO / EN Standard Rack should have 2 No Adjustable, 19” verticals with Punched 9mm Square Hole and Universal 12.7mm-15.875mm-15.875mm alternating hole pattern offering greater mounting flexibility and maximizes usable mounting space The Racks should be 550mm in width and 600 in depth for Network application Approved Make : Netrack /Rittal/APC

Sub Head - III- Cctv

Supply, Installation, Testing and Commissioning of IP based CCTV system for building security comprising of PTZ /fixed camera cabling ,recording display system and hard ware software support -for indoor only (Rates applicable on total plinth level area.)

For External surveillance (rate applicable on total plot area minus plinth area at grounf floor )

Note : Rate includes peripheral ip Based PTZ camera beside indoor camera at reception ,orridores,lift lobby etc wiring up to CCTV room and setting up monnitoring unit/units as required it will cover in sides office room /labs special video wall etc.

Sub Head - IV- Wi-Fi System

Supply, Installation, Testing & Commissioning of the Microservices based WLAN Architecture. The indoor AP should have radios to support 2.4Ghz and 5 Ghz band in a 4X4:4 Mu-MIMO configuration with support for 802.11 a/b/g/n/ac. The AP should have internal Omni Antennas and should support vBLE and RF optimization. It should also support way finding and asset tracking via bluetooth.Should support Artificial Intelligence platform, WIPS/WIDS to detct Rogue APs and the facility to terminate connevction to the Rogue APs.Plenum rated and support for UL 60950-1 CAN/CSAC22.2 No. 60950-1, FCC Part 15.247, 15.407, 15.107, and 15.109 RSS247 ICES003

Sub Head - V Access Control System

Supply, Installation, Testing and Commissiong of the followings :

Supply ,Installation ,Testing & Commissioning of 2 Door 2 reader access control panel with onboard 32 Bit RISC ARM CPU, 8MB flash memory, shall support up to 100000 card user, 400000 event transactions, TCP/IP, the panel should have inbuilt 4 GB SD memory card to take mirror image of device configuration. data shall support standard Wiegand readers, Access Control panel should have MODBUS connectivity to integrate the panel with BMS (Building Management System), with metal enclosure & inbuilt power supply, facility of din-rail mounting should available. capable to integrate with IP/CCTV & NVR for access event alerts, Inbuilt door interlocking facility, SNMP alerts facility, Low battery and AC fail alert facility & reader Tamper detection alert facility should available.

Power Supply- Supply, Installation , testing and commissioning of 12 V SMPS DC Power Supply Unit, highly regulated and spikes free terminal voltage and heavy sourcing current for regulated terminal voltage.

Supply & Installation of Cloud Compatible enterprise level Web based Modular Access Management and Time Attendance software with SQL Database and support up to desired number of users. Single GUI Plateform with complete modular software with provision to integrate with different application ie; Access Control, VMS, Alarm Management, etc. Employee Self Service - login module for Employee/HOD/MANAGER where they can view their attendance; they can apply for leave/manual punch/tour entry/outdoor entry though internet with their login ID & password. Same way manager can online approve all application sent by employee. Comprehensive Email and SMS module for to send various SMS & Email on the base of different events in Access Control & Time Attendance system. It should support Multi company, multi location, multi department, multi login with different rights, muti hierarchy of employee, Should support maker & checker facility - the local administrator should able to add the users but he should not able to authenticate/approve the User, Approval right of theadded user should be with main Administrator. Dedicated output reports for Payroll integration, Duress Authentications, Email & SMS can be sent on every configured event ie; Leave Application/approval, Manaual Punch Application/Approval,Outdoor Application/Approval, Tour Application/Approval, Condone Application/Approval . Holiday restriction (Reader Wise), Device Configuration – Push/Pull, Dual Authentications, Easy Employee tracking as outdoor Employee Attendance should marked with their GPS Location, Employee can mark Offline attendance (If No Network) through Android Mobile App.

Supply ,Installation ,Testing & Commissioning of Mifare smart Card Reader Technical Specs.

Read Range -4-9 cms

Data Read CSN/Sector

Type Smart Card (Mifare Classic)

Transmit Frequency 13.56 MHz

Card (Transponder ) Mifare® Series (ISO14443-A)

Card Read Time 0.1 Sec

Output Interface Wiegand Format (32 Bits)

LED Indicator Bi Color LED

Power supply 12V DC @ 100mA

Material Abs Plastic

Card should be read in1 sec

A Wiegand output that easily interfaces with most existing Wiegand protocol access control panels.

Compact and Elegant. Easily installed on walls and doors.

Supply ,Installation ,Testing & Commissioning of Mifare Smart Card Contactless transmission of data and supply energy (No battery needed), Operating Distance: Upto 100mm (Depending on Antenna Geometry), Operating Frequency: 13.56 MHZ. Fast Data Transfer: 106 Kbit/s High Data Integrity: 16 Bit CRC, parity, bit coding, bit counting. 1 Kbyte, organized in 16 sectors with 4 blocks of 16bytes each (one block consists of 16 byte), User definable access conditions for each memory block. Data retention of 10 years. Mutual three pass authentication (ISO/IEC DIS9798-2), Data encryption on RF-Channel with replay attack protection. Individual set of two keys per sector (per application) to support multi-application with key hierarchy. Unique serial number for each device. Transport key protects access to EEPROM on chip delivery.

Supply ,Installation ,Testing & Commissioning of Electromagnetic Lock 1200 lbs, double leaf, LED Status Display,

Supply, Installation, testing and commissioning of UTP 4 pair 23 AWG CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. Cable 305 mtr per Box. Blue/Orange/White/Green in colour conforming to the following standards like ANSI EIA/TIA 568.2-D, EN50173, IEC 11801 3rd ED, frequency tested upto 400Mhz with Third Party Certificate etc. Cable Dia 6.1 ± 0.3, Cross-member (+) fluted Spine/isolator for uniform separation for all pairs.

Supply and Laying of 8 Core x 1.0 sq mm multi strand, copper, unarmoured shielded Cable as per specification (between the every card readers & the access controllers)

Supply ,Installation ,Testing & Commissioning of U/L Clamp made of aluminium anodised for EM Lock.

Supply , Installation , Testing and commissioning of Exit push button as required.

Supply & laying of Supply and drawing of 2 C X 1.5 Sq mm multi stranded twisted unshielded FRLS Copper cable for Access control system.

Supply and Fixing of 25 mm dia MS Conduit.

Sub Head - VI- Data and Network System

Supplying, installation, testing & commissioning of 42U Rack should have 100% assured compatibility with all equipment’s conforming to DIN 41494 (General Industrial Standard for equipment’s) or Equivalent EIA /ISO / EN Standard,should be 357mm-2068mm in height with 600 and 800 width for Server and Network application. And 1000mm in Depth,Rack unit supported by casters should support a static load of at least 350Kgs and by plinth/Levelers should support a static load of at least 750Kgs,should have Front Glass Door or Flat Perforated Door and Metal Door or Dual Perforated Door,should have Rear Flat Perforated Door and Metal Door or Dual Perforated Door at Rear,Rack should have 2 no’s of removable side panels with slam latch for fast access to cabling and equipment,should have 6U-42U usable Space,should have 4 no’s adjustable, 19” verticals with punched 9mm square hole and Universal 12.7mm-15.875mm-15.875mm alternating hole pattern offers greater mounting flexibility, with Numbered U positions,should include ganging kits for coupling racks,should be manufactured by ISO9001:2015, ISO14001:2004 & OHSAS18001:2007 Certified company and should have proper EHS Policy,must be UL Certified,RoHS Compliance,must certify that the products are Comply DIN41494 and Equivalent EIA/ISO/EN /CEA Standard,rack should comply minimum of IP 20 rating for protection against touch, ingress of foreign bodies and ingress of water should both protect the user from mechanical hazards and generally meet the requirements for a mechanical enclosure (stability, mechanical strength, aperture sizes, etc.) as defined in IEC 60950 Third Edition. Approved Make (Netrack/Rittal/Emerson)

Supplying, installation, testing & commissioning of 15U Racks should be manufactured out of steel sheet punched, formed, welded and powder coated,Rack should have 100% assured compatibility with all equipment’s conforming to DIN 41494 (General Industrial Standard for equipment’s) or Equivalent EIA /ISO / EN Standard Rack should have 2 No Adjustable, 19” verticals with Punched 9mm Square Hole and Universal 12.7mm-15.875mm-15.875mm alternating hole pattern offering greater mounting flexibility and maximizes usable mounting space The Racks should be 550mm in width and 600 in depth for Network application.Approved Make (Netrack/Rittal/Emerson)

Supplying, installation, testing & commissioning of 6 core OS1/OS2 - loose tube outdoor/corrugated steel tape with Unitube construction Crush Resistance 2000N with 8.5 mm Diameter and confirming to IEC/EN 60793-2-50 class B1.3 ITU G.652.D EN 50 173-1:2007 ISO/IEC 11801:2002 ISO/IEC 24702:2006 Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, Testing and Commissioning of 19" slide-in modular optic drawers with galvanised steel accommodates up to 4 fibre optic units, 4 cables, accommodates up to 12 LC connectors. Should meet EN50173 and ISO/IEC 11801 operating specifications Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, Testing and Commissioning of 19" slide-in modular optic drawers with galvanised steel accommodates up to 4 fibre optic units, 4 cables, accommodates up to 24 LC connectors. Should meet EN50173 and ISO/IEC 11801 operating specifications Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, Testing and Commissioning of Single Mode OS1/OS2 LC-LC Duplex Fiber Patch Cord - 3 mtrs. Conform to IEC 61754-4,61300-3-4,61300-3-34,61300-3-6,61300-2-1/2/4/5 EIA-TIA, G.657.A2 and Telecordia performances requirements Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, testing and commissioning of UTP 4 pair 23 AWG LSZH CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 305 mtr per Box. Blue/Orange/White/Green in colour conforming to the following standards like ANSI EIA/TIA 568.2-D, IEC 60332-1, IEC 60754-1, ASTM 2843. Frequency tested upto 400Mhz with Third Party Certificate etc. Cable Dia 6.0 ± 0.3, Cross-member (+) fluted Spine/isolator for uniform separation for all pairs. Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, testing and commissioning of 24 port Cat 6 19" Modular Toolless Patch Panel (loaded) enable all possible combinations of the various types of cable (UTP, FTP, SFTP) mounted on the same panel by using various toolless connector blocks/modules. Have a metal structure enabling them to be durably fixed to the uprights of the 19” chassis and assuring automatic grounding between toolless RJ-45 connectors, the panel, and the 19” uprights of the enclosure. Include rear cable support with plastic cable guides to hold cable without need for cable ties. Include quick mounting system to mount the panel into the 19” rails without use of cage-nuts. These may be used to secure the connections of wifi access points, IP cameras, servers, or other critical devices. Front Removal IO's option for maintenance and trouble shooting with 6 Different Colours Labels for Labelling & Identification of Individual Ports. Tested and guaranteed under dual circuit IEEE PoE++ more than 90W for up to 2500 on-load connections / disconnections. Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, testing and commissioning of Cat6 Tool less Information outlet for Data & Voice. Cat6 U/UTP RJ45 socket with built in crimping mechanism with capability of retermination without refreshing the wires. Toolless RJ45 Information outlet with insertion cycle (in & out) upto 2500 times (I/O) along with front side Label holder and transparent shutter. The Information Outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3bt standard for POE++ application Approved Make (Panduit/Siemon/Legrand)

Supplying, installation, testing & commissioning of Face Plate : Flush & surface mount. Polycarbonate Hi-Grade Plastic FR Grade with ABS underplate & CRCA metal fram & UV Resistant 850 degree C/ Glow Wire Test. The face plate should be compatible for Cat5e, Cat6 range of RJ45 and different types of AV connectors.The face plate Size should be of minimum 86x86mm with backbox Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, Testing and Commissioning of RJ-45 Connector

Supply, Installation, Testing and Commissioning of CAT6 UTP 24 AWG LSZH Patch Cord - 1 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like Smoke density: Series IEC 61034 / IEC 61034-2, EN 61034-2, IEC 60754/IEC 60754-2, EN 60754-2, IEC 60332-1/60332-1-2, UL VW-1 with tensile strength >50N, Number of Insertion upto 2500 Duty Cycle Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, Testing and Commissioning of CAT6 UTP 24 AWG LSZH Patch Cord - 2 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like Smoke density: Series IEC 61034 / IEC 61034-2, EN 61034-2, IEC 60754/IEC 60754-2, EN 60754-2, IEC 60332-1/60332-1-2, UL VW-1 with tensile strength >50N, Number of Insertion upto 2500 Duty Cycle Approved Make (Panduit/Siemon/Legrand)

Supply, Installation, Testing and Commissioning of 25MM PVC Pipe Approved Make (YGP/Powerflow/Precision)

Supply, Installation, Testing and Commissioning of 25MM HDPE Pipe Apporved make (Varni/YGP/Precision)

Supply, Installation, Testing and Commissioning of 32MM Flexible Pipe

Supply, Installation, Testing and Commissioning of 50MM Flexible Pipe

Supply, Installation, Testing and Commissioning of 100X50 mm Trunking

Supply, Installation, Testing and Commissioning of 24 x 25G SFP+ Switch with additional 8 x 25G SFP+ Ports, All 24 port should support Mgig with 10G/25G Ports, should have internal redundant power supply, should have dedicated stacking port, should support advanced features like static routing, RIP, PIM, OSPF, VRRP, PBR, QoS, Switch shall have provision to upgrade advance features VXLAN and VRFs. Switch’s Operating System should be tested under Common Criteria Certification. and complying to details technical specs in attached sheet Approved Make - Extreme/Cisco/Juniper/Aruba

Supply, Installation, Testing and Commissioning of 24 x 10/100/1000 Base-T Switch with additional 4 x 10G SFP+ Ports, should have internal redundant power supply, shall have minimum 128 Gbps of switching fabric and 95 Mpps of forwarding rate, must have dedicated slot for modular stacking-support for minimum 80 Gbps of stacking throughput with 8 switch in single stack, should support advanced features static routing, RIP, PIM, OSPF, VRRP, PBR and QoS features from Day1, Switch’s Operating System should be tested for EAL 2/NDPP or above under Common Criteria Certification. and complying to details technical specs in attached sheet Approved Make - Extreme/Cisco/Juniper/Aruba

Supply, Installation, Testing and Commissioning of 24 x 10/100/1000 Base-T PoE+ Switch with additional 4 x 10G SFP+ Ports, switch should provide PoE power budget of 370W with option of providing up to 740W, should have internal redundant power supply, shall have minimum 128 Gbps of switching fabric and 95 Mpps of forwarding rate, must have dedicated slot for modular stacking-support for minimum 80 Gbps of stacking throughput with 8 switch in single stack, should support advanced features static routing, RIP, PIM, OSPF, VRRP, PBR and QoS features from Day1, Switch’s Operating System should be tested for EAL 2/NDPP or above under Common Criteria Certification. and complying to details technical specs in attached sheet Approved Make - Extreme/Cisco/Juniper/Aruba

Supply, Installation, Testing and Commissioning of 2.4GHz & 5.0GHz Dual Band 802.11ax Wave2 Access Points with 4x4 MU-MIMO, 4 Spatial Streams. Must Support data rate up to 5gbps.; AP should be upgradable to Integrated Bluetooth radio; AP should have 1 Gigabit port, 1 Management Console Port with License Approved Make - Extreme/Cisco/Juniper/Aruba

Supply, Installation, Testing and Commissioning of Wireless Access Point Solutions : Supply, Installation, Testing & Commissioning of Wireless Controller scalable up to 500 Access Points in future by adding license. The controller should support at least 10000 clients including future scalability. The Controller should have application visibility, multiple SSID support,802.11ac Wave 1 and Wave 2 and 802.11ax support. Centralized, Distributed and Mesh deployment support. The controller should support Digital Network Architecture and SD Access. Approved Make - Extreme/Cisco/Juniper/Aruba

Supply, Installation, Testing and Commissioning of Maximum distance of up to 10 km Hot-pluggable Single-mode fiber 10GBASE-LX/LR/SR Duplex Fiber module with LC connector Approved Make - Extreme/Cisco/Juniper/Aruba

SUB HEAD- VI- SOLAR PANEL

Solar Panels

Supplying, installation, testing and commissioning of Solar Panels: MonoPerc Half cut cells, (144 cells), having 72 cells configuration with wattage ranging from 525W to 555W High fill factor for improved energy conversion efficiency Cell sorted by power and current to minimize mismatch losses in the field Electroluminescence tested for micro cracks Highly reliable IP68 rated junction box MC4/MC4 compatible cable connectors Torsion and corrosion resistant with anodized aluminium frame Unique back sheet design for high resistance to moisture ingress Enhanced reliability through use of distinctive encapsulant and back sheet Ultra- soft interconnect with stress relief for enhanced reliability Optimized edge clearance for high quality rugged design.

Supplying, installation, testing and commissioning of Solar Inverters: 80KW On-Grid 3 Phase 415V IP 65 MPPT, with Inbuilt SPD Complete with 7 Years material.

Sub Head - II- Mechanical Items

Supply & installation of Aluminium MonoRail/ Strud Channel on Shed; with FRP 310mm Walkway for Service , Hardware SS 304 grade spring nuts,washer,nutbolts complte as required to fix or as instructed by the engineer in chage.

Sub Head - III - Elecrtical Items

Supply installation testing ad commisioning of

ACDB LT Panels - (Ratings as per SLD, IP 65) RMS System with 5 year portal subscription+ Zero Export DC Cables: 4 sq.mm, 1C Copper Solar cable, Type I AC Cable (Inverter to ACDB): 50 sqmm 4C Copper- AC Cable (ACDB to LT Panels): 185 sq.mm, 3.5C All Arm. 20 mtrs ESE Lighting Arrestor: 107 Mtr range, 5 mtr Mask + Accessories Chemical Earthing- GI Electrode 2mts, 250 micron CPRI Tested GI Strip - 3Run 25X6mm with Saddle & Insulator

Supply installation testing ad commisioning of

MC4 connecters (+/-) ive, Cable Thimbles, Glands, Ferules, UV & SS Cable Ties, Danger Singages, Fire Extuinguiser Dressing Material - 1" DWC with bends, Steel Corrogated UPVC flexible 25/32mm GI Cable Tray 200X75X1.2mm with cover and accessories Plumbing System with CPVC Pipelines nozzles and 1HP Motor-1Nos

PART-VIII PARKING MANAGEMENT SYSTEM

Sub hed -I Supply, Installation, Testing, Commissioning of - Smart Parking Managemnt solution

Supply Installation Testing Commissioning of- Outdoor type electromechanical Boom Barrier • Barrier Gate Up to 3 Mtr (1 Sec) Electronic control board and power supply • Corrosion resistant cabinet MS Powder coating • Opening/closing Time 1 sec • 100% Duty Cycle • MTBF -10 million Life Cycle • Manual release • With following specifications. • Machine core with compression spring, effectively avoids the accidents caused by spring breaking • Die-casting aluminium alloy motor, precision and good at thermal radiating • Motor cooling fan, solving the problem of heat-protection • Double safety limit switches (photo electricity limit switch/motor memory sensor) • Reversing on obstacle • Auto-closing • Support the externa INFRARER PHTOCELL for anti-bumping and human safety function (Optional) • Support the external and internal VEHICLE LOOP DETECTOR (Optional) • Traffic light interface • Wire control (switch signal)/ Remote control (418MHZ) 12. RS485 communication module (optional) • Running Time 1 Sec • Max Boom Length 3 Meters, Boom Type (Straight Telescopic) • Boom Dimension 45*80 MM (octagonal) • Motor Torque 600 NM • Duty Cycle 100% • Voltage 220V -/+ 10%, 110V -/+ 10% • Frequency 50/60 HZ • Motor Voltage 220 V • Power 100 W • Working Temperature 0 C to 65 C • Protection Grade IP 54 • Corrosion resistance Cabinet • With Push Button and all required accessorise Approved make- Parknsecure/impark/Swarco/Parkilio

Supply Installation Testing Commissioning of- EPC enabled READER for four wheeler with Protocol ISO 18000-6B, EPC Class 1 Gen2 (ISO18000-6C) • Protection Grade IP 66 (Ideal For Application In Harsh Environment) • Work Frequency Standard ISM 865-868MHz (Europe), 902~928MHz (USA) • 865-867MHz (India) • Frequency Hopping FH S OR Fixed Frequency Transmission (Supports RSSI) • Power Output 0 – 30 dBm (adjustable) • Antenna Built-in 9dBi Circular Antenna • Interface Rs232, RS485, Wiegand 26/34 ( TCP/IP & Wi-Fi) • External Antenna One External Antennae Port. (Optional) • Module IMPINJ R2000 Module • Relay 2 Nos Built-In Relays • Operating Mode Answer, Active, Trigger • Read Range 12– 15m. • Write Range 0 – 6m • Reading Clue Buzzer / LED • Input Power 100-240V, DC 9V – 24V POE (Power Over Ethernet) • Power Consumption 4.5W • Operation Temp -25°C ~ +60°C • Storage Temp -25°C ~ +80°C • Humidity 10 – 95 % C Approved make- Parknsecure/impark/Swarco/Parkilio

Supply Installation Testing Commissioning of- ANPR- Integrated design, IP67 with long range access ANPR camera & with inbuilt OCR AI for four Wheeler only, with VAM Software with ANPR software licence each lane-Designed to cater to the needs of facilities where parking is allocated to Authorized vehicles or detect visitor number plate • Integrated with entrance automation, equipment such as Boom Barriers • ACS Controllers, Readers • ANPR, LD, Reader etc. Designed with high-performance CMOS image sensor and independently-developed processor, capable of reading and extracting detailed vehicle information day and night. Intelligent deep learning algorithm allows recognition of vehicle license plate, and vehicle brand, model, logo, and colour. The camera is extensively applied to vehicle capture and recognition of community road, parking lot, and other entrance and exit surveillance scenarios. • High-quality image Industry-specific GS-CMOS image sensor with high sensitivity, high SNR and excellent WDR provides lifelike images in all weathers • Complete intelligence High-performance CPU processor helps extract and analyse information of motor and non-motor vehicles in real-time, providing vehicle feature details for business decision-making. • High-level protection Integrated design with low power consumption, built-in lightning protection module, and IP67 protection grade, suitable for various harsh environments. • GS-CMOS image sensor · • Video compression standards: H.265/H.264M/H.264H/H.264B/MJPEG • Multiple ports various signal, data and communication ports, capable of connecting to external devices such as barrier. • Easy installation Built-in LED illuminator and motorized vari-focal lens, providing ease of installation and commissioning • Technical Specification:- Illuminator 6 white light illuminators (brightness adjustable) • Image Sensor 1/1.8'' CMOS • Image Resolution 1920 × 1080 (OSD black strip excluded) • Video Resolution Main stream: 1080P (1920 × 1080) / 720P (1280 × 720) Sub stream: 720P (1280 × 720) / D1 (704 × 576, 704 × 480) / CIF (352 × 288, 352 × 240) • Video Frame Rate PAL: Main stream (1280 × 960@25fps, 1280 × 720@25fps), sub stream: (1280 × 720@25fps, 704 × 576@25fps, 352 × 288@25fps) NTSC: Main stream (1280 × 960@30fps, 1280 × 720@30fps), sub stream (1280 × 720@30fps, 704 × 408@30fps, 352 × 240@30fps) • Bit Rate H.264B: 20Kbps–32768Kbps H.264M: 20Kbps–32768Kbps H.264H: 20Kbps–32768Kbps H.265: 20Kbps–32768Kbps MJPEG: 59Kbps–65536Kbps • Video Encoding H.264B/H.264M/H.264H/H.265/MJPEG • Image Encoding JPEG • Noise Reduction 3DNR • White Balance Full auto; auto colour temperature range; customized colour temperature • Electronic Shutter 1/50–1/10000, auto or manual • Wide Dynamic Range 96db • Edge Enhancement Yes • Exposure Mode Full auto; customized auto; customized • Iris Auto iris (W:1.3–T:2.3) • Function: Trigger Mode Video detection; I/O coil; video detection and I/O coil • Shutter Single shutter • Storage 1 built-in TF card port. Kingston 16G, 32G and 64G; 16G, 32G and 64G; SanDisk 16G, 32G and 64G • Image Tampering Prevention Yes. Video/picture can be checked through watermark and verification • Max Illumination Distance 25m (82.02ft) • Alarm Event Alarm in the case of no storage card, not enough storage space, storage card error, network disconnection, IP conflict, and illegal access • Security Mode Authorized username and password, MAC address binding, HTTPS encryption, IEEE 802.1x, and network access control • OSD Overlay Supports overlay of time, address (position of channel), lane(number/ direction), plate (number and colour), vehicle (speed, colour, type) • ANR (Automatic Network Replenishment) Yes. Platform/FTP • Auto Register Yes • Intelligence- Vehicle Detection Vehicle capture rate ≥99% • Vehicle Recognition Supports recognizing vehicle type, vehicle logo, vehicle colour, license plate, and vehicle without plate. Vehicle recognition rate ≥90% • Video Metadata- Intelligent Track Frame Intelligent frame display. Supports displaying vehicle plate and vehicle path • Ports:- Module lens • 1 Analog Output - 1 Ethernet Port 1 100/1000M Ethernet port (RJ45) • 1 RS-485 port • 2 I/O Port opt coupler input (switch quantity) • Alarm Input 1, opt coupler input (switch quantity) • Alarm Output 2-channel relay output, connecting to devices such as barrier • Audio Input 1-channel RCA port • Audio Output 1-channel RCA port • Power Output 12V DC±10% voltage output, ≤1A current output • General: Power Supply 12V DC, 24V AC, PoE • Power Consumption < 20W • Working Temperature −30°C to +65°C (−22°F to +149 °F) • Working Humidity 10%–90% (no condensation) • Housing Metal and plastic • Protection Grade IP67

Supply Installation Testing Commissioning of- PCB Based VAM controller, 64-Bit Soc @ 1.4Ghz processor or Fanless 5th generation Intel® Core i3 up to 2.7GHz Dual-Core Four-Thread processor or 26 bit Wiegand controller with On board Memory with Polycarbonate or MS Enclosure and PSU and relay board

Supply Installation Testing Commissioning of- MS Pole with branding BOX and L arm

Supply Installation Testing Commissioning of- Status LED display Alpha numeric 2x1 p10 module Parking availability display board Led Colour Red Led Type Oval Outdoor water proof Led Pitch 10 mm vertical 10 mm Horizontal Character Height each line 6 inch in each line visible from 100 ft Language English / Numeric Message Changing By wired Lan connectivity Power supply 230vac +-10% 50 Hz • Communication –Serial port/ TCP-IP/ LAN 220V AC ± 15% Operating temperature range: -10ºC to +70ºC Material: High heat ABS blend MS PU Body with mounting clamp

Supply Installation Testing Commissioning of Server withProcessor- Up to one Intel® Xeon® E 2224G with up to 4 cores per processor • Memory: IMM Speed Up to 2666 MT/s, Memory Type UDIMM, Memory Module Slots-4 DDR4 slots, Maximum RAM-UDIMM 16GB • Storage-Front Bays-One 3.5"" 1TB SATA SSD by default; up to 3 x 3.5"" SATA HDDs • Storage Controllers-Software RAID Intel® VROC 6.x • Security-Cryptographically signed firmware, Secure Boot, Intel® SGX (Software Guard Extensions), TPM 2.0 • Management: Embedded / At-the-Server, Intel AMT 12.0 • Power Supplies-Bronze 300W • Ports: Network options:1 x 1GbE • Front ports:2 x USB 2.0, 1 x USB 3.1, 1 x USB 3.1 • Rear ports: 2 x PS2, 2 x Display ports, 1 x Serial,1 x Audio, 2 x USB 2.0, 4 x USB 3.1 • Slots-PCIe, 1 X Gen3 slot (x16), 2 X Gen3 slot (x4), 1 X PCI • Form Factor: Mini tower • Win Server 2019 "

Supply Installation Testing Commissioning of Hand held POS Device with PMS POS app, Connectivity Wi-Fi & 4G 5 Inch colour Display Multiple Communications High speed Thermal printer Contactless/ NFC Quad- core Cortex A7 processor Smart Droid based on Android Memory 1GB ROM, 8 GB ROM Display 5.0-inch colour display, 1280x720 pixels resolution 2 Mp Rear Camera with Flash 2 inch high speed thermal printer , paper roll: 58mmX40mm Contactless card reader 1x Sim + 2 x SAM card slots Communications: 4G/5G/ Bluetooth/ BLE/Wi-Fi Speaker for Audio Battery: 7.4 V 2000 mAh, rechargeable Li-ion battery Adopter: input 100-240V AC , 50/60 Hz: output : 5.0V DC, 2.0A 1x Micro USB2.0, 1x DC Jack, 1x Micro-SD Peripheral Ports Charging Base: 1x DC 3.5mm Port (POGO), 1x LED Power indicator .Multi-Function Docking Base- Scanner window, 2x type- A HOST USB 2.0, 1x RJ45 (Serial port), 1x RJ45 (LAN), 1x DC 3.5mm port (POGO), 1x led indicator, 1x LED communicator indicator (SIM and Subscription in client scope) Hand Held Machines applications should have option to collect tariff fee through Cash, UPI, CC,DC with Complete in all respect with all required accessories- The job includes the cost of all the petty material etc. With 1 years onsite warranty

Supply Installation Testing Commissioning of Handheld Fastag RFID Reader with Fastag PMS POS App , FasTag- Handheld for Fastag payment- Fastag RFID Reader with Android rugged mobile computer with powerful processor, 8000mAh battery and superb UHF Fastag RFID Reader. Equipped with Impinj Indy R2000, linearly or circularly polarized antenna. It can read FasTag from long distance .Android 8.1 Operating System or Android 11.0 Operating System Android 8.1; Soti Mobi Control, SafeUEM supported CPU Cortex-A53 2.5 GHz Octa-core RAM+ROM 3 GB + 32 GB Expansion Supports up to 128 GB Micro SD card WLAN IEEE802.11 a/b/g/n/ac, 2.4G/5G dual-band, internal antenna Bluetooth v2.1+EDR, 3.0+HS, v4.1+HS GNSS GPS/AGPS, GLONASS, BeiDou; internal antenna WWAN 2G: 850/900/1800/1900 MHz 3G: B1,B2,B4,B5,B8 4G: B1,B2,B3,B4,B5,B7,B8,B12,B17,B20,B25,B40,B66 Dimensions 164.2 x 80.0 x 24.3 mm / 6.46 x 3.15 x 0.96 in. Weight 654 g / 23.07 oz Display 5.2'' IPS FHD 1920 x 1080 Touch Panel Corning Gorilla Glass, multi-touch panel, gloves and wet hands supported Power Li-ion, rechargeable, 8000 mAh Standby: over 500 hours Continuous use: over 12 hours (depending on user environment) Charging time: 3-4 hours (with standard adaptor and USB cable) • Expansion Slot 1 slot for SIM card, 1 slot for SIM or TF card Interfaces USB 2.0 Type-C, OTG, Type-C headphones supported • Audio Speaker, 2 microphones • Keypad 4 front keys, 1 power key, 2 scan keys, 1 multifunctional key • Sensors Gravity sensor, light sensor, proximity sensor User Environment Operating Temp. -4 o F to 122 o F / -20 o C to 50 o C • Storage Temp. -40 o F to 158 o F / -40 o C to 70 o C Humidity 5% RH - 95% RH non condensing Drop Specification Multiple 1.5 m / 4.9 ft. drops (at least 20 times) to the concrete across the operating temperature range Tumble Specification 1000 x 0.5 m / 1.64 ft. falls at room temperature Sealing IP65 per IEC sealing specifications ESD ±15 KV air discharge, ±6 KV conductive discharge Camera 13 MP Autofocus with flas Frequency 865-868 MHz / 920-925 MHz / 902-928 MHz Protocol EPC C1 GEN2 / ISO18000-6C Antenna Circular polarization (4dBi), linear polarization(1.8dBi) Power 1 W (30 dBm, +5 dBm to +30 dBm adjustable) 2 W R/W range Up to 15 m (circular polarization, open outdoors, Impinj MR6 tag); up to 7 m (linear polarization, open outdoors) Fastest Read Rate 900+ tags/sec (circular polarization)• Barcode Scanning (Optional) NFC Frequency 13.56 MHz Protocol ISO14443A/B, ISO15693, NFC-IP1, NFC-IP2, etc. Chips M1 card (S50, S70), CPU card, NFC tags, etc. Range 2-4 cm Accessories Standard AC Adaptor, USB Cable, etc. Optional Cradle, Holster, etc. with Complete in all respect with all required accessories- The job includes the cost of all the petty material etc. With 1 years onsite warranty

Supply Installation Testing Commissioning of- Touchless Ticket Dispenser TVM Should be Touchless ticketing system along with an inbuilt QR reader, RF Proximity reader, Push button, Touchless hand wave button, DIC, and SOS (VOIP Optional) and with a 7” display and indicator LED. with an inbuilt controller, router, and power supply with a side opening, also it can be integrated with PMS application through Push/Pull data technology Robust and efficient ticket dispensing mechanism centralized control and processing of all car park-related transactions Maintenance of accounting and administration protocols Revenue control functions that prevent attempts of customer and staff theft or leakage from the system Revenue and Yield Management functions to analyze trends and create financial reports – resulting in a greater revenue return to our clients Management of operational procedures such as staff attendance and daily reports Modular reporting format to suit the owner’s needs and return meaningful tailored information Management and tracking of car park records – simplifying end-of-day/ month reporting Ticket format -Digit-coded serial numbers 16-24 digits (Alphanumeric) It can print predefined content with Date, Time, Vehicle No (Through ANPR) Lane No, Plaza ID, project Name, QR Code, 1D/2D Barcode. Configurable content available with software Dispensing & Access Method-Touchless with Hand wave, Push Button, Proximity Card, QR Code and TFT Control Program -Python, C#, Dot Net Printer-Printing Method – Direct Line Thermal Printing Speed – 160 mm/sec max Resolution – 203 dpi Number Dots a align – 448 Dots Paper width – 60 mm Auto Cutter – Guillotine type Sensor – Yes Cutter - Yes Ticketing Speed -25 tickets/min (Depending upon the other parking system speed) Ticket Dispensing capacity -Up to 4000 (Depending up on GSM of paper) Type of Ticket-70-150 GSM Ticket Length/Width-Width 60 mm, Length can be adjustable Display-18 cm, 7” LCD (Capacitive Touchscreen –optional) Res. – 800 x 480 Display interface – HDMI, USB. Backlight control to lower power consumption Touchless Switch- No Touch sensor diffused detection with non-touch infrared sensor and with 2 LED colours. Free from contagious disease spread 2 LED indicators for sensor stand-by or approached sensor Detection range – 0.1-10 cm Out contact – NO/NC/COM Push Button (Secondary Ticket vending option)- Out contact – NO/NC/COM Barcode/QR Reader-Barcode/QR Reader with 1D/2D reading capacity. With features CMOS sensor, Infrared sensor, Visual feedback, and Dual interface. Image Sensor – 800 x 800 COMS, Illumination – White LED Depth of field – EAN 13: 0-190 mm Depth of field Code 39: 40-210mm Depth of field Code 128: 0-185mm Depth of field QR: 0-130mm Min Print Contrast: 25% Scan Angle roll: 360° Scan Angle Pitch: +- 40 Scan Angle Skew: +- 40 Field of view Horizontal: 74° Field of view Vertical: 74° Scan Modes: Sense Mode, Continuous Mode Scan Window: 50mm x 50mm 1D: All major 1D and 2D symbologies, including PDF 417, data matrix, QR code, micro QR code, etc. Interface: RS 232 USB Notification: Beep, LED indicator DIC (Optional)-Driver Image Capturing: 2MP camera SOS (Optional)-VoIP SIP module intercom with forward speaker, input call button Video Intercom (Optional) 2MP camera with noise separation Low Illumination with IR supplement, true WDR communication port TCP/IP. Trigger IO based FOV: Horizontal - 130°, Vertical – 78° Resolution: 1920 x 1080 p Proximity Reader-Proximity Card Reader Frequency:125KHz, ASK Output Interface: Wiegand 26 Bits, Clock-and-Data Read Range: Up to 5cm Support: Tags EM4100, TK4100, JH4101, EM4101 Configuration: CSN Control Panel-Relay circuitry up to 16 relays can be sugar cube) Opto Driven Digital Isolated inputs 12 Third-Party Wifi Router Placement on the PCB Indicator LED with Pull up down resistors 3 no’s Onboard AC input with output to drive to SMPS via a rocker switch Onboard provision to accept 12 v and 5 v dc from SMPS Onboard 9 v regulator for the reader's power Input and output terminals are using RMC connector Power Inputs and outputs are with terminal blocks with a pitch of 5 mm Processor-Processor: 1.4GHz 64-bit quad-core processor or Intel chipset industrial PC Dual-band wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and Power-over-Ethernet support Broadcom BCM2837B0, Cortex-A53 64-bit SoC @ 1.4GHz Memory: 1GB LPDDR2 SDRAM Connectivity: 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLE Gigabit Ethernet over USB 2.0 (maximum throughput 300Mbps) 4 × USB 2.0 ports Access: Extended 40-pin GPIO header Video & sound: 1 × full size HDMI MIPI DSI display port MIPI CSI camera port 4 pole stereo output and composite video port Multimedia: H.264, MPEG-4 decode (1080p30); H.264 encode (1080p30); OpenGL ES 1.1, 2.0 graphics SD card support: Micro SD format for loading operating system and data storage Input power: 5V/2.5A DC via micro USB connector 5V DC Vehicle Detection-Through a presence loop or photo sensor to trigger the system, The ticket can be issued by waving hand over the Touchless button or by Pushing the button Protection -IP54 (For outdoor use shade recommended) Temperature: -10°C to 50 °C Humidity: Control through inbuilt Fan Dimensions-W 457 x H 1538 x D 466 Electrical Protection-Yes with circuit breaker Housing-Powder quoted CR Sheet, Colour – Light grey with Dark Grey front Maintenance & Paper Loading-Left side opening with lock Integration-Boom Barrier, External Controller, ANPR, etc. Duty Cycle-100% Power Supply -220-240 +/- 10% VAC, 50 Hz Connectivity-TCP/IP, LAN Offline Operation-Yes (But data need to push at the server end once get LAN connection is restored for reporting purpose) Remote Access-Yes Dispensing Program-Yes, Prebuilt as well as per site requirement Temperature-0°C - 55°C Storage-20°C -75°C Humidity-< 90% RH Language-English or On demand Country of Origin-India Certificates-CE, FCC, ISO with Complete in all respect with all required software modules- The job includes the cost of all the petty material etc. With 1 years onsite warranty

Supply Installation Testing Commissioning of- Manned Point of Sale Including POS kiosk with 19" display ,Fanless Industrial grade CPU with Integrated 5th generation Intel® Core i3 up to 2.7GHz Dual-Core Four-Thread processor with 2 GbE LAN, Thermal printer , QR reader, User fare display, Custom Keyboard, Mouse, Electric Drawer with POS and Barrier Integration. Cashier Terminal for payment on foot or from vehicle at exit or at any central location. It can process all types of transactions and accept all means of payment. It should also allow printing of all types of QR tickets. Manages all types of transactions: Hourly parking: payment for regular or lost ticket. Pass-cards: payment for subscriptions and renewals, parking overstay payment. Conference and event tickets: sale, parking overstay payment. Sale of vouchers and prepaid cards (in time or money, usable at entry/exit or as means of payment). Various payment methods: cash, prepaid cards, credit and debit cards, UPI. The Cashier Terminal should includes the following features: (Porta Cabin in client scope) Barcode/QR Reader-Barcode/QR Reader with 1D/2D reading capacity. With features CMOS sensor, Infrared sensor, Visual feedback, and Dual interface. Image Sensor – 800 x 800 COMS, Illumination – White LED Depth of field – EAN 13: 0-190 mm Depth of field Code 39: 40-210mm Depth of field Code 128: 0-185mm Depth of field QR: 0-130mm Min Print Contrast: 25% Scan Angle roll: 360° Scan Angle Pitch: +- 40 Scan Angle Skew: +- 40 Field of view Horizontal: 74° Field of view Vertical: 74° Scan Modes: Sense Mode, Continuous Mode Scan Window: 50mm x 50mm 1D: All major 1D and 2D symbologies, including PDF 417, data matrix, QR code, micro QR code, etc. Interface: RS 232 USB Notification: Beep, LED indicator Printer-Printing Method – Direct Line Thermal Printing Speed – 160 mm/sec max Resolution – 203 dpi Number Dots a align – 448 Dots Paper width – 60 mm Auto Cutter – Guillotine type Sensor – Yes Cutter - Yes Electrical Cash drawer Customer fee and date/time display Flat screen monitor 19" Customized Keyboard, Mouse Dynamic QR for UPI payments kiosk Proximity Reader-Proximity Card Reader Frequency:125KHz, ASK Output Interface: Wiegand 26 Bits, Clock-and-Data Read Range: Up to 5cm Support: Tags EM4100, TK4100, JH4101, EM4101 Configuration: CSN Change facility should be available in cash drawer Monthly Card Renewal, membership, pass Reading & management of discount tickets Receipt issue and Report generation On line with central server Processor-Processor: 1.4GHz 64-bit quad-core processor or Intel chipset industrial PC Dual-band wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and Power-over-Ethernet support Broadcom BCM2837B0, Cortex-A53 64-bit SoC @ 1.4GHz Memory: 1GB LPDDR2 SDRAM Connectivity: 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLE Gigabit Ethernet over USB 2.0 (maximum throughput 300Mbps) 4 × USB 2.0 ports Access: Extended 40-pin GPIO header Video & sound: 1 × full size HDMI MIPI DSI display port MIPI CSI camera port 4 pole stereo output and composite video port Multimedia: H.264, MPEG-4 decode (1080p30); H.264 encode (1080p30); OpenGL ES 1.1, 2.0 graphics SD card support: Micro SD format for loading operating system and data storage Input power: 5V/2.5A DC via micro USB connector 5V DC Connectivity-TCP/IP, LAN Offline Operation-Yes (But data need to push at the server end once get LAN connection is restored for reporting purpose) Remote Access-Yes Temperature-0°C - 55°C Storage-20°C -75°C Humidity-< 90% RH Language-English or On demand Country of Origin-India Certificates-CE, FCC, ISO with Complete in all respect with all required software modules- The job includes the cost of all the petty material etc. With 1 years onsite warranty

Supply Installation Testing Commissioning of- Software for ANPR acknowledgement and validation with 97% accuracy Functional Specification of Application Software for ANPR The system should automatically detected approaching vehicle at the installed location by means of Inductive loops/ IR Sensor. On detection of Vehicle approach, the system would active the license plate image capture cameras in real time The system shall perform OCR (Optical Character Recognition) of the License plate Character (English alpha Numeric characters in standard fonts) The system shall store image of Vehicle and license plate and enter the license plate number OCR into OEM specified database along with date timestamp and site location details. System should be able to detect and recognize the alpha numeric License plate in all standard font and formats of all type of vehicles The system should have option to identify license plates according to the Black/white listed categories by authorized personnel. Multitenant based Visitor management Module Can classify Vehicle type through colour of number plate CMOS image sensor and processor ALGORITHM for in-depth extraction and analysis of vehicle information 24/7 Embraces deep learning algorithm for accurate recognition of vehicles license plate, and vehicle model, vehicle logo, vehicle series, vehicle colour, and more with Complete in all respect with all required accessories- The job includes the cost of all the petty material etc. With 1 years onsite warranty

One Time Charges for fast tag system integrations with NETC & NPCI which include One Time Charges For fast Tag System Integrations with NETC & NPCI (National Payments Corporation of India) which includes facility like- Real time transaction processing. Customers can link their FASTag to their existing savings /current account/Credit Card or to a prepaid account. For opening a prepaid account it is not mandatory to have an existing relationship with the issuer bank FASTag facilitates electronic payments at the parking plaza while the vehicle is in motion. An instant SMS notification of the transaction sent to the customer. Customer can recharge FASTag account online through issuing member banks portal using UPI/ Card/ NEFT/ RTGS /Net Banking OR BBPS. And fast tag databased access licence and integration with NECT &NCPI (MDR @3%+GST extra and deducted from each transection by BNAK/ NPCI/ Service provider

Supply Installation Testing Commissioning of Road Speed Breaker

1 GBPS internet cooncetion monthly basis

Parking Information System

Supply Installation Testing Commissioning of PIS Server withProcessor- Up to one Intel® Xeon® E 2224G with up to 4 cores per processor • Memory: IMM Speed Up to 2666 MT/s, Memory Type UDIMM, Memory Module Slots-4 DDR4 slots, Maximum RAM-UDIMM 16GB • Storage-Front Bays-One 3.5"" 1TB SATA SSD by default; up to 3 x 3.5"" SATA HDDs • Storage Controllers-Software RAID Intel® VROC 6.x • Security-Cryptographically signed firmware, Secure Boot, Intel® SGX (Software Guard Extensions), TPM 2.0 • Management: Embedded / At-the-Server, Intel AMT 12.0 • Power Supplies-Bronze 300W • Ports: Network options:1 x 1GbE • Front ports:2 x USB 2.0, 1 x USB 3.1, 1 x USB 3.1 • Rear ports: 2 x PS2, 2 x Display ports, 1 x Serial,1 x Audio, 2 x USB 2.0, 4 x USB 3.1 • Slots-PCIe, 1 X Gen3 slot (x16), 2 X Gen3 slot (x4), 1 X PCI • Form Factor: Mini tower • Win Server 2019

Supply Installation Testing Commissioning of- PIS Software with Software application interface like A program menu allows easy access to all function pages To manage, and monitor the Parking Information system via a graphic interface of the entire parking facility layout

Supply Installation Testing Commissioning of- 1 Row 4 Digit Dis play Red P10 module (TCP-IP/RS485) (indoor with roof hanging mount) ❑ Work Temp: -10° C – 55° C ❑ Multi- Color LED Matrix Display unit ❑ Voltage rating: 230 Vac, 50 Hz ❑ Currentrating: 1A, 5A ❑ Communication frequency: 9600 ❑ Luminance: 1000cd/m2 ❑ Dot matrix: 320x 120 mm ❑ LED Color: R/G/B Super bright. ❑ Communication: RS232/RS485/TCP/IPOptional ❑ Frequency: 50 – 60 Hz ❑ Cabinet Color : Black ❑ Visibility-40-50 Mtr ❑ Baud: 4800 bps/9600 ❑ Customize as persite requirement

Supply Installation Testing Commissioning of- Main Outdoor display at entry Gate with 7X1 P10 module RGB Main Display (Outdoor at main Gate with Pole mount) Multi Row InformationDisplay ❑ Work Temp: -10° C – 55° C ❑ Multi- Color LED Matrix Display unit ❑ Voltage rating: 230 Vac, 50 Hz ❑ Currentrating: 1A, 5A ❑ Communication frequency: 9600 ❑ Luminance: 1000cd/m2 ❑ Dot matrix: 320x 120 mm ❑ LED Color: R/G/B Super bright. ❑ Communication: RS232/RS485/TCP/IPOptional ❑ Frequency: 50 – 60 Hz ❑ Cabinet Color : Black ❑ Visibility-40-50 Mtr ❑ Baud: 4800 bps/9600 ❑ Customize as persite requirement

Supply Installation Testing Commissioning of- Counting Controller- Parking Counting Controller with 4 Relay/4DI Modbus/SNMP/MQTT Ethernet Remote I/O is a versatile device designed for efficient and remote management of parking systems. Equipped with 6 channels of relay output and 2 channels of digital input (counter), it enables seamless integration with various parking equipment and sensors. ❑ IMulti-Protocol Support: Supporting MQTT (TLS), SNMP, Modbus TCP, RESTful API, and ASCII protocols, it ensures compatibility with a wide range of existing network infrastructures and IoT platforms, facilitating seamless integration and communication. ❑ Advanced Logic Control: Featuring GCL (Graphical Control Language), it enables the creation and execution of basic logic control rules, allowing for customized automation and response actions based on specific parking scenarios or events. ❑ Peer-to-Peer Mapping: With its peer-to-peer function, the device can map I/O statuses between multiple controllers, facilitating synchronized operations and enhanced system redundancy in larger parking facilities. ❑ Robust Construction: Built to withstand harsh environmental conditions, the device offers an operating temperature range of -10 to55 °C (-40 to 158 °F) and boasts 2 isolation voltage, ensuring reliable performance in challenging outdoor environments.

Cable and conduit

Supply Installation Testing Commissioning of- CAT6 Twisted Pair A Cable

Supply Installation Testing Commissioning of-3 core 1.5 Sqmm Power cable

Supply Installation Testing Commissioning of- 25 mm MPVC Conduit-25mm PVC Heavy Duty

Supply Installation Testing Commissioning of- OFC cable 6 core

Supply Installation Testing Commissioning of- 8 T+2SFP port Switch

Supply Installation Testing Commissioning of- LIU 6 port loaded

Supply Installation Testing Commissioning of-OFC Patch coard

Supply Installation Testing Commissioning of- Cat 6 patch cord

Supply Installation Testing Commissioning of- SFP 1G

Supply Installation Testing Commissioning of- 10 Sfp+4T port SFP L3 switch

Supply Installation Testing Commissioning of-LIU 12 port loaded

Supply Installation Testing Commissioning of-OFC Patch coard

Supply Installation Testing Commissioning of-Cat 6 patch cord

Supply Installation Testing Commissioning of-SFP 1G

Supply Installation Testing Commissioning of-Enclosure outdoor with Fan and PSU

Supply Installation Testing Commissioning of 32 U floor Mounted rack 32U FLOOR STANDING RACKS Usable Height : 30 U Actual Width / Usable Width : 600 mm / 19" Actual Depth / Usable Depth: 800 mm / 425 mm(max) Door : Rear steel door fitted on hinges With locking arrangement and having opening at >140 degree. Front : Glass Door fitted on hinges with locking arrangement Material Used for Fabrication CRCA steel sheet Bend Test (3 times) 45 Thickness of Material 1.2 mm for Racks , 2mm for Vertical equipment angles Powder Coating Coat Thickness =80-90 Microns Coating Shade-Cabinet=Light Grey Steel Door/Glass trims=Light Grey/Dark Grey Other Features Fixed Side panels - 02 Nos Top & Bottom cable entry provision at rear Heavy duty Castors for easy movement - 01 set ( 2 with brakes and 02 without brakes) 19” wide adjustable mounting rails utilizing full width Standards Rack conforms to DIN 41494 & IEC 297 standard

SUB HEAD -II Parking Guidance System

Supply Installation Testing Commissioning of- PGS Software with Software application interface like A program menu allows easy access to all function pages To manage, and monitor the guidance system via a graphic interface of the entire parking facility layout

Supply Installation Testing Commissioning of- Directional LED Information Panel - Three digits to show available parking spaces and an arrow for direction. ❑ Brightness 2000 MCD ❑ Communication:RS232/RS485/TCP/IP/PGS ❑ Cabinet Color : Black ❑ Visibility 50 mtr ❑ LED Color: Red /Green Super bright. ❑ Display the empty parking spaces in the form of figure and arrow, ❑ MS profile and organic glass panel casing ❑ Green indication and distinguishable. ❑ Lamp bead type 6-8 seconds SMD LED lamp bead ❑ Operating AC 110 ~ 240V ❑ Power ≤10W (one direction) ❑ Temperature -10°C ~ +55°C ❑ Humidity ≤90% RH ❑ Luminance 339 LUX

Supply Installation Testing Commissioning of-Ultrasonic Sensor With LED, Combi ultrasonic sensors and LED lamp indicators into one device. Each parking space requires one ultrasonic combi sensor LED installed in front of the parking space. (Red & Green Color By Default other Color on request) ❑ Detection Range adjustment 2.5 m to 3 ❑ Installation location - Above front of the parking slot ❑ Horizontal – 1. 0~0.5m, Vertical- 2~3m ❑ Operating voltage - DC 10~28V (Rated 24V) ❑ Power consumption - <1W ❑ Working temperature -10°C ~ +55°C , humidity-up to 70%RH ❑ Appearancematerial- Grey ABS engineering plastics ❑ Communicationmode - RS485 ❑ Communicationmode - 2 RJ45 ports ❑ Communication distance - ≤300m ❑ Power supply distance - ≤150m ❑ Response time of the detector-After parking - 2s~10s ❑ Type of the indicator light -Red and green two-tone high-light LED ❑ Ranging error- 2cm ❑ Detection accuracy - >99.9% ❑ Communication frequency: 9600

Supply Installation Testing Commissioning of- Zone controller - One Zone controller can connect up to 30 ultrasonic sensor LEDs. It gathers and forwards vacancy information from all the detectors to the Central Control Unit, and also forwards commands from the Central Control Unit to the LED information panels connected to it for displaying proper vacant information. ❑ Zone controller to receive data from 30 to 50 Sensor depending upon distance ❑ 32-bit ARM processor ❑ Remotely upgraded to always satisfy the user's requirements. ❑ CAN BUS communication interface ❑ Two-way RS485 communication interface ❑ Industrial design for strict tests of static, lightning stroke,surge and group pulse ❑ Devices is designed with the short circuit transposition and misconnection protection ❑ Working temperature -10°C~ +55°C ❑ Communicationmode 1-circuit CAN / 2-circuitRS485 ❑ Casingmaterial-Mild Steel Powder Coated Black ❑ Communication distance CAN: ≤1000m (RVSP 2*1.0, RS485: ≤300m ❑ Single-circuit node capacity 15-25 Sensors and LED ❑ Power consumption ≤2W

Supply Installation Testing Commissioning of- Floor Control Unit - One parking floor requires one Floor Control Unit. . The Floor Control Unit gathers and forwards information from Zone Controllers to the Central parking guidance server for management operation. It can also provide vacancy information to additional level or area vacancy LED display boards connected. Controllers should use RS485/TCP/IP, Can BUS hybrid communicationmechanismto solve the Problem of long-distance communication, the expansion of network nodes, group managementissues. ❑ The Node/Floor Controller to collect all parking information in floor and uploading the related collected information code to the Central Controller. I It is used to connect Zone and Central Controllers. BUS communicationmechanism ❑ 32-bit ARM processor ❑ Floor Controller can be remotely upgraded ❑ overvoltage protection ❑ Groupingmanagement of the Zone Controller ❑ Optimal management of network communication and complete protocol conversion and data grouping processing between centralized and Zone Controllers. ❑ Casingmaterial Mild Steel Powder Coated Black ❑ Working temperature -10°C ~ +55°C ❑ Operating voltage AC 110 ~ 240V ❑ Communicationmode 2 CAN-BUS ❑ Communication distance ≤1000m (RVSP 2*1.0) ❑ Power consumption ≤100W

Supply Installation Testing Commissioning of- Central Control Unit -One parking facility requires one Central Control Unit. It can connect up to 15 floor Controllers at the maximum. The Central Control Unit gathers and forwards information from Floor Controllers to the PGS parking guidance server for management operation. It can also provide vacancy information to additional level or area vacancy LED display boards connected. Controllers should use RS485/TCP/IP, Can BUS hybrid communicationmechanismto solve the Problem of long-distance communication, the expansion of network nodes, group managementissues. ❑ Floor Controller can be remotely upgraded ❑ overvoltage protection ❑ Optimal management of network communication andncomplete protocol conversion and data grouping processing between centralized and Zone Controllers. ❑ Casingmaterial Mild Steel Powder Coated Black ❑ Working temperature -10°C ~ +55°C ❑ Operating voltage AC 110 ~ 240V ❑ Communicationmode 2 CAN-BUS ❑ Communication distance ≤1000m (RVSP 2*1.0) ❑ Power consumption ≤100W

Supply Installation Testing Commissioning of- 4 core 1 Sqmm Power cable

Supply Installation Testing Commissioning of- 25 mm MS Conduit-25mm

PART-C FURNITURE ESTIMATE

Sub Head-I Furniture MLCP

LOUNGE CHAIR - FEEDING ROOM Cafe Chair Overall Size 480W x 490D x 780H . . Base Seat & Back Made Of Moulded PP Structure Supported ( Single Piece Moulded Seat & Back Shell ) . Understructure Base Of Chair Round SS Pipe Structure Fixed Type . Understructure Base Fixed Type 19mm Dia SS Round Pipe 1.2mm Thick . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 780 & Depth 490mm . 440W x 410D Base Seat Moulded With PP Structure & 440W x 390H Back Seat Moulded With PP Structure . Height From Seat To Ground 420mm . All SS Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . Assembly Shell Affixed On MS Frame With Help Of Screw . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

SINGLE SIZE BED-PIONEER - 03 Overall Size 1981L x 940W x 810H1 x 600H2 . Bed Used Upper Top 12mm Commercial Plyboard . Bed Made Of Prime Quality CRCA Rectangular , Square & Round Metal Pipe Powder Coated Finish With Approved Shade . Bed Main Leg Made Of 38mm Dia 1.2mm Thick Round Metal Pipe Duly Powder Coated . Main Structure Supported To 19mm Dia Round Metal Pipe 1.2mm Thick Powder Coated . Bed Two Side Supported 50x25 Metal Rectangular Pipe 1.2mm Thick Powder Coated . Other Two Side Supported To 40 x 20 Rectangular Metal Pipe 1.2mm Thick Powder Coated . Under Ply Supported To Be 25 x25 Square Metal Pipe 1.2mm Thick Powder Coated . 25 x 25 x 3mm Thick MS Angle Supported To Ply Board . Bed Structure Pipe 19mm Dia. Welded To 38mm Dia. Metal Round Pipe . No Sharp Edges Of Pipe Ends . Height From Ground To bed 450mm High . Legs Of The Bed Hard Rubber Shoes . All Metallic Panels Screw With Nut & Bolt . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Thickness Of Coating (40 – 50) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for hostel FURNITURE range for ergonomic design.

Table Type - 1 (3M X 0.09M) Overall Size:-3000WX900DX750Hmm, Table Top 25+18mm Thick PLPB Board , All Wooden Panels Finish With 2mm PVC Edge banded , Top Supported Under structure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board , Modesty Panel Prime Quality 18mm Thick 600mm High PLPB Board Supported To Top, Top supported under Box design with three drawer pedestal on one side and on another side two number of sliding drawer , All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment , All Wooden Panels Prime Quality Board With ISI Marked.(Design as per reference image).

Table Type - 2 (3M X 0.09M) Overall Size:-3000WX900DX750Hmm, Table Top 18+18mm Thick PLPB Board , All Wooden Panels Finish With 2mm PVC Edge banded , Top Supported Under structure Of Table Gable - End Made Of Prime Quality 25mm Thick PLPB Board , Modesty Panel Prime Quality 18mm Thick 600mm High PLPB Board Supported To Top, Side cabinet Top to be made up of 25mm thick PLPB with 2mm thick PVC edge bending ,Side cabinet below top with 2-number of drawer and one number of openable shutter , Side cabinet under structure made up of 18mm thick PLPB with PVC edge bending , Side cabinet back panel to be made up of 9mm thick PLPB , Skirting made up of 18mm thick PLPB with 2mm thick PVC edge bending, All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment , All Wooden Panels Prime Quality Board With ISI Marked.(Design as per reference image)

Table Type - 3 (2.3M X 075M) Ebony main table (Size: L: 2300 x W: 750 x H: 770 mm) Tops are made of 45 mm effect with full compact half moon T molding with Melamine finish in Rosewood. Melamine finish provides water, heat & scratch resistant. Sides are made of 25 mm with full compact PVC edging with Melamine finish in Rosewood. Fronts are made of 25 mm with full compact PVC edging with Melamine finish in Rosewood. Melamine finish provides water, heat & scratch resistant. Metal Frame for side panel ensure strength & durability for aesthetics look. Adjustable leg for table ensure comforts and convenience . Grommet for desktop wire management to avoid cramped desks and messy wring. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table Type - 4 (2M X 0.75M) Ebony main table (Size: L: 2000 x W: 750 x H: 770 mm) Tops are made of 45 mm effect with full compact half moon T molding with Melamine finish in Rosewood. Melamine finish provides water, heat & scratch resistant. Sides are made of 25 mm with full compact PVC edging with Melamine finish in Rosewood. Fronts are made of 25 mm with full compact PVC edging with Melamine finish in Rosewood. Melamine finish provides water, heat & scratch resistant. Metal Frame for side panel ensure strength & durability for aesthetics look. Adjustable leg for table ensure comforts and convenience . Grommet for desktop wire management to avoid cramped desks and messy wring. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table Type - 4 (1.8M X 0.75M) Office Table Top 25mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade . Riva SeriesTable Size 1800W x 750D x 750mm . Fixed Pedestal Size 400W x 450D x 640H . Side Storage Size 1050W x 500D x 700H . Table Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board , Fixed Drawer Top 18mm Thick Wooden Board With 0.8 mm Thick Edgebanded . Mobile Drawer Used Sliding Telescopic Channel With All Fittings & Shutter Used C - Frame Handles . Fixed Drawer Move On Twin Wheel Casters 50mm Dia . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted . Side Storage Top 25mm Thick Top With 2mm Thick Edgebanded . 18mm Thick Wooden Shelve & Divider . Storage Front Facia 18mm Thick PLPB Sliding Shutter . 50mm High Wooden Panel Skirting Provided in Side Storage . 7mm High Pvc Bofurs Screw With Gable - end & Side Storage . All Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Office Table Top 25mm Thick Wooden Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade . Table Size 1800W x 900D x 750mm . Mobile Pedestal Size 400W x 450D x 640H . Side Storage Size 1050W x 500D x 700H . Table Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Mobile Drawer Top 18mm Thick Wooden Board With 0.8mm Thick Edgebanded One Side Ducknose Postform . Mobile Drawer Used Sliding Telescopic Channel With All Fittings & Shutter Used C - Frame Handles . Mobile Drawer Move On Twin Wheel Casters 50mm Dia . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted . Side Storage Top 25mm Thick Ducknose 25 mm thick With 2mm Thick Edgebanded . 18mm Thick Wooden Shelve & Divider . Storage Front Facia 18mm Thick PLPB Sliding Shutter . 50mm High Wooden Panel Skirting Provided in Side Storage . 7mm High Pvc Bofurs Screw With Gable - end & Side Storage . All Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table top made to the shape as per design and having overall size of 1400WX600DX70m , under structure made of 18mm thick plywood with 0.6mm Mica pated , modesty panel made of 25mm thick , Table fixed with bottom edge beading as per requirement , Modesty Panel of Main table shall be finished with matching veneer 3±4mm of approved grains and colour with design as per engineer in charge , Side pedestal Main Table shall be sliding drawers made of 12 mm ply sides and bottom , 18 mm front and within 18mm BB boxing etc complete , Drawers provided for Main table shall be fixed with sliding channels handles locks etc complete , All visible surfaces of side to be finished with PU polish All internal and underneath surfaces of table shall also be finished with PU polish , All edge beading nails screws adhesives etc complete , all wooden surfaces shall be finished with PU polish.

Table 900m dia 750mm ht. , 18mm thick PLPB Top, crome plated frame structure. Table Top 18 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . Understructure Made Of Prime Quality 1.6 mm Thick frame. Understructure round pipe of crome platedl, Pipe 50 x 50mm With 1.6 mm Thick All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table Top 25mm Thick PLPB Board ( OSL ) With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . All Over Size Of Table 2100W x 1000D x 750H . Understructure Made Of Prime Quality CRCA 50 x 50mm Square Metal Pipe Duly Powder Coated . Understructure CRCA Metal Pipe 50 X 50mm With 1.6 mm Thick Four Side Welded With Vertically Metal Pipe . Legs Of The Table Hard Rubber Shoes . Understructure CRCA Square Metal Pipe 50 x 50mm With 1.6 mm Thick All Side Welded With Vertically & Horizontally Metal Pipe powder coated All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table 1200m dia 750mm ht. , 18mm thick PLPB Top, crome plated frame structure. Table Top 18 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . Understructure Made Of Prime Quality 1.6 mm Thick frame. Understructure round pipe of crome platedl, Pipe 50 x 50mm With 1.6 mm Thick All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table Top 25mm Thick PLPB Board ( OSL ) With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . All Over Size Of Table 2400W x 1050D x 750H . Understructure Made Of Prime Quality CRCA 50 x 50mm Square Metal Pipe Duly Powder Coated . Understructure CRCA Metal Pipe 50 X 50mm With 1.6 mm Thick Four Side Welded With Vertically Metal Pipe . Legs Of The Table Hard Rubber Shoes . Understructure CRCA Square Metal Pipe 50 x 50mm With 1.6 mm Thick All Side Welded With Vertically & Horizontally Metal Pipe powder coated All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table Top 25mm Thick PLPB Board ( OSL ) With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . All Over Size Of Table 2400W x 1050D x 750H . Understructure Made Of Prime Quality CRCA 50 x 50mm Square Metal Pipe Duly Powder Coated . Understructure CRCA Metal Pipe 50 X 50mm With 1.6 mm Thick Four Side Welded With Vertically Metal Pipe . Legs Of The Table Hard Rubber Shoes . Understructure CRCA Square Metal Pipe 50 x 50mm With 1.6 mm Thick All Side Welded With Vertically & Horizontally Metal Pipe powder coated All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Conference Table Top 43 mm Thick (25mm Top + 18mm Batten) PLPB Board as Per Approved Laminate Shade. Understructure Top Supported 75X25mm Prime Quality Steel Frame Leg moulded With 18mm Thick PLPB Board. Modesty Panel 18mm Thick 450 mm High PLPB Board Supported To Top. Conference Table Top Size 3000W X 1200D In 18mm Thick PLPB Board. Provided Wire Management For Conference Table Top Flushed With Flapper. Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Conference Table Top Divided Into Two Parts. All Wooden Panels, Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment. All Wooden Panels Cleaning Corner Knitted Finish. Legs Of The Table having Hard Rubber Shoes. Metal Flapper Size 400W X 120D Duly Powder Coated. All Wooden Top , Legs & modesty Panels Assembled & Dismental Any Places Easily. Metal Leg 75x25mm Shall be Neatly Jointed Together With 18mm Thick PLPB Board Accurrately Matching Sides Avoiding Any Gaps. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Conference Table Top 43 mm Thick (25mm Top + 18mm Batten) PLPB Board as Per Approved Laminate Shade. Understructure Top Supported 75X25mm Prime Quality Steel Frame Leg moulded With 18mm Thick PLPB Board. Modesty Panel 18mm Thick 450 mm High PLPB Board Supported To Top. Conference Table Top Size 6500W X 1300D In 18mm Thick PLPB Board. Provided Wire Management For Conference Table Top Flushed With Flapper. Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Conference Table Top Divided Into Two Parts. All Wooden Panels, Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment. All Wooden Panels Cleaning Corner Knitted Finish. Legs Of The Table having Hard Rubber Shoes. Metal Flapper Size 400W X 120D Duly Powder Coated. All Wooden Top , Legs & modesty Panels Assembled & Dismental Any Places Easily. Metal Leg 75x25mm Shall be Neatly Jointed Together With 18mm Thick PLPB Board Accurrately Matching Sides Avoiding Any Gaps. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Top Designed With 18 mm Thick Commercial Board Affixed With 0.6mm Mica. Overall Size 4500W x 1200D x 750H. Modesty Panel Having Affixed With Veneer Pressed With Polish. Wire Manager of Dia 50 mm Should Be Provided On Top For Fixing The Mic. All Edge And Structure Finished With Proper Color Combination Matched To Laminated Shade. Legs Of The Podium Hard Rubber Shoes. Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Conference Table Top 43 mm Thick (25mm Top + 18mm Batten) PLPB Board as Per Approved Laminate Shade. Understructure Top Supported 75X25mm Prime Quality Steel Frame Leg moulded With 18mm Thick PLPB Board. Modesty Panel 18mm Thick 450 mm High PLPB Board Supported To Top. Conference Table Top Size 3000W X 1200D In 18mm Thick PLPB Board. Provided Wire Management For Conference Table Top Flushed With Flapper. Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Conference Table Top Divided Into Two Parts. All Wooden Panels, Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment. All Wooden Panels Cleaning Corner Knitted Finish. Legs Of The Table having Hard Rubber Shoes. Metal Flapper Size 400W X 120D Duly Powder Coated. All Wooden Top , Legs & modesty Panels Assembled & Dismental Any Places Easily. Metal Leg 75x25mm Shall be Neatly Jointed Together With 18mm Thick PLPB Board Accurrately Matching Sides Avoiding Any Gaps. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Top Designed With 18 mm Thick Commercial Board Affixed With 0.6mm Mica. Overall Size 6500W x 1300D x 750H. Modesty Panel Having Affixed With Veneer Pressed With Polish. Wire Manager of Dia 50 mm Should Be Provided On Top For Fixing The Mic. All Edge And Structure Finished With Proper Color Combination Matched To Laminated Shade. Legs Of The Podium Hard Rubber Shoes. Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table size- 2300x600x750 Top to be made up of ISI mark 25 mm thick pre laminated Particle Board finished with 2 mm thick PVC edging applied on Through Feed Edging Machine UNDERSTRUCTURE- The under structure to be made up of CRCA, legs shall be of pipe of size 50x50mm and 40x40 cross member for support and stability finished with powder coating. Race way – CRCA raceway for carrying electrical and data wiring are provided below the table top with provision for fixing switches. Each cluster to be provided with wire riser from floor to wire raceway. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for LAB FURNITURE range for ergonomic design.

Table 900m dia 750mm ht. , 18mm thick PLPB Top, crome plated frame structure. Table Top 18 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . Understructure Made Of Prime Quality 1.6 mm Thick frame. Understructure round pipe of crome platedl, Pipe 50 x 50mm With 1.6 mm Thick All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Cafe Table Top 25mm Thick PLPB Board (OSL ) With 0.8mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade . Overall Size 900 Dia X750H . Table Top Dia 600 mm . Understructure SS Round Pipe . Base Supported 4 Prone . 2mm Sheet Top Supported Plate Under The Table Top . Wooden Panels Cleaning Corner Knitted Finish . Top Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Overall Size:-2000WX750DX750H mm, Top to be made up of 43mm thick PLPB with 2mm thick PVC edge bending, Side Cabinate Storage wih Top Size:-1050WX450DX750mm, Pedestal and storage top to be made up of 25mm thick PLPB with 2mm thick PVC edge bending, Under structure to be made up of 18mm thick PLPB with PVC edge bending, Main table modesty to be made up of 18mm thick PLPB with PVC edge bending with on front side aluminium strip as per reference image, below table top under three drawer fixed pedestal with one number of lock and three number of S.S handle ,ERU storage having three number of openable shutter and open space as per reference image, All Wooden Panels Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment , All Wooden Panels Prime Quality Board With ISI Marked.

LINEAR WORKSTATION IN 60MM THK PANEL BASED SYSTEM. SIZE - 1500 X 600 (1200H)-1500 X1200 WITH --R/W--WITH S/B,18 MM THK PLPB LEG ,TOP-25MM TH PLPB-1500 X 600 lipped,3 DRAWER UNIT IN PLPB-400 X 450 X 680,KEY BOARD TREY,CPU TROLLEY

LINEAR WORKSTATION IN 60MM THK PANEL BASED SYSTEM. SIZE - 1500 X 600 (1200H)-1500 X1200 WITH --R/W--WITH S/B,18 MM THK PLPB LEG ,TOP-25MM TH PLPB-1500 X 600 lipped,3 DRAWER UNIT IN PLPB-400 X 450 X 680,KEY BOARD TREY,CPU TROLLEY

Supplying & Fixing of METHODEX make Alice CenterTable size 700x700x450mm as per drawing & specification and directed by Engineer-in-Charge. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design.

Supplying & Fixing of METHODEX make Alice CenterTable size 1000x600x450mm as per drawing & specification and directed by Engineer-in-Charge. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design.

Supplying & Fixing of METHODEX make Bloom CenterTable size 1800x600x450mm as per drawing & specification and directed by Engineer-in-Charge. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design.

Supplying & Fixing of METHODEX make Alice CenterTable size 900x900x450mm as per drawing & specification and directed by Engineer-in-Charge. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design.

Table 600m dia 750mm ht. , 18mm thick PLPB Top, crome plated frame structure. Table Top 18 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . Understructure Made Of Prime Quality 1.6 mm Thick frame. Understructure round pipe of crome platedl, Pipe 50 x 50mm With 1.6 mm Thick All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Cafe Table Top 25mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade . Wooden Round Top Dia 450. Base Plate SS Dia 380 mm With 8 mm Thickness. 3mm Sheet Top Supported Plate Under The Table Top Screw With Round Wooden Panel Cleaning Corners Knittted Finished. Plate Supported Round Pipe 60mm Dia & 16 Guage. Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Table Top Rectangular Type Made Of Prime Quality 19mm Thick Commercial Board Affix With 3mm Veneer At Top . Table Top Size 500W X 500D in 19mm Thick Commercial Board . Wooden Leg Size 430mm Height. Understructure Top Supported Frame & Leg Made Of Prime Quality Solid Wood. Commercial Board Use Prime Quality With ISI Marked. All Wooden Panels Cleaning Corner Knitted Finish. Wooden Panel Joint Leg To Leg Supported To Top. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design.

Reception table 2100 X 750 X 750/1200 MM. Providing & Fixing Table made out of 18mm thick ply finished with 1 laminate (are over exposed surface) . Table shall have pedestal .units with drawers & shutter below made in 18 mm thk Comm.plywood ISI grade, finished with 1 mm thk. . The table is supported on base made of 18 thk Comm.plywood ISI grade finished with 1 mm thk mica laminate . Table shall have linning in internal exposed surfaces of drawers and Storage Cabinets in approved colour laminate of 1.0 mm thick mica of approved Shade,colour & Make. Provision for two receway trays & foot rest shall be made. Drawers are to be fitted with Telescopic Channels ,Unit will also have cable manager for wires & cables. The rate shall include all necessary hardware like 75mm.long Brass/S.S.hinges/Albihari Hinges, catchers, handels,drawer Telescopic channels, locks of approved quality . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Reception table 2100 X 750 X 750/1200 MM. Providing & Fixing Table made out of 18mm thick ply finished with 1 laminate (are over exposed surface) . Table shall have pedestal .units with drawers & shutter below made in 18 mm thk Comm.plywood ISI grade, finished with 1 mm thk. . The table is supported on base made of 18 thk Comm.plywood ISI grade finished with 1 mm thk mica laminate . Table shall have linning in internal exposed surfaces of drawers and Storage Cabinets in approved colour laminate of 1.0 mm thick mica of approved Shade,colour & Make. Provision for two receway trays & foot rest shall be made. Drawers are to be fitted with Telescopic Channels ,Unit will also have cable manager for wires & cables. The rate shall include all necessary hardware like 75mm.long Brass/S.S.hinges/Albihari Hinges, catchers, handels,drawer Telescopic channels, locks of approved quality . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

High Profile Revolving High Back Chair Made Of Good Quality Products Of MSPL Standard Models . Overall Size 1310H x 650D . Seat Plywood Made Of 15mm Hot Pressed Supported . Upholstery PVC Structure Moulded With Prime Quality Leatherite . PHA ( Gas-Lift ) 85mm ( TDC 152mm & BDC 67 ) . Understructure Base Revolving Pedestal Chrome Plated Steel Base With PP Hub Cap . Machanism Torsion Bar Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 1310 & min Depth 650 . 510W x 510D Base Seat 120mm Thick Moulded With PU Foam , D - 45 kg/m3 , H - 20 & 520W x 720H Back Seat 100mm Thick Moulded With PU Foam , D - 45 kg/m3 , H - 20 . Base Seat Shell NA . Back Seat Shell NA . L - Patta NA . Beading Finish NA . 465/605 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest Soft Cushioning On Fixed Chrome Plated Base . Arm Rest Height From Seat 205mm . Height From Seat To Ground 550mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 650mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia .

Visitor Chair Made Of Good Quality Products Of MSPL Standard Models . Overall Size 840H x 580D . Seat & Back Plywood Made Of 12mm Hot Pressed Supported . Understructure Base Of Chair Metal Structure Fixed Type . Seat & Back Are Firmly Connected To The Base Frame Metal Structure . Chair Max Height 840mm . Upholstery , PHA & Machanism NA . 480W x 450D Base Seat 80mm Thick Moulded With PU Foam , D - 45 kg/m3 , H - 20 & 510W x 460H Back Seat 80mm Thick Moulded With PU Foam , D - 45 kg/m3 , H - 20 . 465/558 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Base Seat Shell ABS Cover At Underside . Back Seat Shell ABS Cover At Back Side . L - Patta Mild Steel . Beading Finish With NA . Arm Rest Height From Seat 190mm . Height From Seat To Ground 480mm . Understructure Metal Frame Structure Made Of 25mm Round Metal Pipe 2mm thick Duly Powder Coated . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Thickness Of Coating (40 – 50) Micron.

Medium back revolving chair,Fabric back with adjustable lumber support, PU moulded foam with fabric upholestry seat, PU Padded adjustable armrest, Nylon base & Nylon Wheels, Synchro tilt mechanism with upright position locking. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Medium back revolving chair,Fabric back with adjustable lumber support, PU moulded foam with fabric upholestry seat, PU Padded adjustable armrest, Nylon base & Nylon Wheels, Synchro tilt mechanism with upright position locking. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Medium back revolving chair,Fabric back with adjustable lumber support, PU moulded foam with fabric upholestry seat, PU Padded adjustable armrest, Nylon base & Nylon Wheels, Synchro tilt mechanism with upright position locking. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Medium back revolving chair,Fabric back with adjustable lumber support, PU moulded foam with fabric upholestry seat, PU Padded adjustable armrest, Nylon base & Nylon Wheels, Synchro tilt mechanism with upright position locking. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Cafe Chair Overall Size 450W x 510D x 880H . Seat & Back Plywood Made Of 12mm Hot Pressed Having Radius At Bend Supported . Understructure Base Of Chair Chrome Plated Round ERW Tube Structure Fixed Type . Upholstery Structure Prime Quality 12mm Bend Ply . Understructure Base Fixed Type 19mm Dia Round ERW Pipe 1.2mm Thick Chrome Finished . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 880 . 415W x 400D Base Seat 12mm Thick Ply & 420W x 460H Back Seat 12mm Thick Ply . Height From Seat To Ground 470mm . All Chrome Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

High Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed Back Pipe Structure . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric Mesh . PHA ( Gas-Lift ) 85mm (TDC 152mm & BDC 67) . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking Fixed Back & Back Tilts . Tilt Adjustment Can Be Operated In Seating Position . Chair Max Height 1100 &715D . 490W x 470D Base Seat 65mm Thick Moulded With PU Foam D - 42kg/m3 & 470W x 580H 25mm Thick Back Seat Pipe Structure Moulded Fabric Mesh . 440/585 Arm Rest Adjustable Type PU . Arm Rest Height From Seat Min - 185mm & Max - 250 . Base Seat Shell NA . Back Seat Shell Pipe Structure . L - Patta Mild Steel . Beading Finish NA . Height From Seat To Ground 500mm . Understructure Base Steel Inserted PP Base With PP Hub . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . Pedestral Pitch Centre Dia 715mm With C. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Visitor Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed Back Pipe Structure . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric Mesh . Understructure Base Of Chair Metal Structure Fixed Type . Seat & Back Are Firmly Connected To The Base Frame Metal Structure . Chair Max Height 860mm x 590D . PHA & Machanism NA . 490W x 460D Base Seat 65mm Thick Moulded With PU Foam , D - 45 kg/m3 , H - 20 & 480W x 420H Back Seat 25mm Thick Moulded With Pipe Structure Moulded Fabric Mesh . 445/590 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Base Seat Shell NA . Back Seat Shell Pipe Structure . L - Patta NA . Beading Finish NA . 445/590 Arm Rest Adjustable Type PU . Arm Rest Height From Seat Min - 175mm & Max - 235 . Height From Seat To Ground 470mm . Understructure All Metal Frame Structure Made Of 25mm Round Metal Pipe 2mm thick Duly Powder Coated . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Thickness Of Coating (40 – 50) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Medium Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat & Back Plywood Made Of 12mm Hot Pressed Supported . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric Mesh . PHA ( Gas-Lift ) 105mm ( TDC 171mm & BDC 66 ) . Understructure Base Revolving Pedestal Chorme Plated Steel Base With PP Hub Cap . Machanism Torsion Bar Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 1125 & min Depth 715 . 490W x 480D Base Seat 60mm Thick Moulded With PU Foam , D - 45 kg/m3 , H - 18 & 460W x 560H Back Seat 15mm Thick Moulded With Pipe Structure . Back , Seat Shell NA & L - Patta Mild Steel . Beading Finish With NA . 460/630 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest Height From Seat Min 205mm & Max 265mm . Arm Rest Made Of P.U + LBkt . Height From Seat To Ground 480mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 715mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Metal powder coated frame three seater sofa-L-3CH ADV.

Revolving chair, Seat 15mm Hot pressed plywood with PU molded foam with Fabric Upholstery, Back 12mm Hot Pressed plywood with PU molded foam with Fabric upholstery connected with metal plate from seat, PU padded Adjustable Armrest, Push Back Mechanism with Upright position locking, 100mm Class 4 Gaslift with cover, Metal Powder coated base with Nylon wheels. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Three Seater Sofa-MS SOFA-505-3

Two Seater Sofa-MS SOFA-505-2

Single Seater Sofa-MS SOFA-505-1

Two Seater Sofa-MS SOFA-505-5

Cafe Chair Overall Size 480W x 490D x 780H . . Base Seat & Back Made Of Moulded PP Structure Supported ( Single Piece Moulded Seat & Back Shell ) . Understructure Base Of Chair Round SS Pipe Structure Fixed Type . Understructure Base Fixed Type 19mm Dia SS Round Pipe 1.2mm Thick . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 780 & Depth 490mm . 440W x 410D Base Seat Moulded With PP Structure & 440W x 390H Back Seat Moulded With PP Structure . Height From Seat To Ground 420mm . All SS Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . Assembly Shell Affixed On MS Frame With Help Of Screw . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Metal powder coated frame three seater sofa with Moulded seat & back- L-3CH ADV. UP

Metal powder coated frame three seater sofa with Moulded seat & back- L-3CH ADV. UP

Metal powder coated frame three seater sofa with Moulded seat & back- L-3CH ADV. UP

Bean Bag in leathe finish

Table 450m dia 750mm ht. , 18mm thick PLPB Top, crome plated frame structure. Table Top 18 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . Understructure Made Of Prime Quality 1.6 mm Thick frame. Understructure round pipe of crome platedl, Pipe 50 x 50mm With 1.6 mm Thick All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Table Top Designed With 25 mm PLPB . Top Size 3000W x 600D. Understructure Leg Designed With combination of 50x50 and 40X40mm Square CRCA 16 Guage Thick Duly powder Coated . Legs Of The Table Hard Rubber Shoes. Wooden Panels Prime Quality Board With ISI Marked . MIG Welding All - Around The Weld Joints Using Inert Gas (Argon.) The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

STORAGES WITH 25MM LIPPED TOPS 18MM U/S AND 9MM PLPB BACK- W X 450 D X 1050 H WITH SWING SHUTTERS Top 18mm Thick 2mm Edgebanded Finished Approved Laminate Shade , All Storage Body Made Of 18mm Thick PLPB Board With 2mm Thick PVC Edgebanded Finish of Approved Laminate Shade , Shutter Used Metallic Hinges With All Fittings , All Storage Screw With Minifix Provided Locks & Handles , All Wooden Panels , Shelve & Shutters Fix Joints With Minifix Dowels & Other Fitting Equipment , Wooden Panels Cleaning Corner Knitted Finish , All Wooden Panels Prime Quality Board With ISI Marked , Overhead Provided One No Of Shelve of 18mm Thick PLPB Board.

MODULAR STORAGE TYPE 1 (7.7M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 2 (3.51M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 3 (2.87M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 4 (1.57M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 5 (3.4M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 6 (1.75M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 7 (1.91M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 7 (6.94M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 7 (2.03M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 7 (2M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 7 (6.25M X 0.45M X 1.05M)

MODULAR STORAGE TYPE 7 (4.22M X 0.40M X 1.05M)

MODULAR STORAGE TYPE 7 (8.25M X 0.60M X 1.05M)

MODULAR STORAGE TYPE 7 (1.57M X 0.75M X 1.05M)

MODULAR STORAGE TYPE 7 (0.78M X 0.75M X 1.05M)

Cafe Table Top 1200x750mm Designed With 25 mm Thick PLPB Board 2mm Thick PVC Edgebanded Finish Approved Laminate Shade . Cafe Table Top Two Side Side Postform & Other Two Side Flat Edgebanded. Understructure Leg Designed With 25mm Dia CRCA Round Metal Pipe 18 Gauge Thick 40 - 50 Microns Powder Coated . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Cafe Chair Overall Size 480W x 490D x 780H . . Base Seat & Back Made Of Moulded PP Structure Supported ( Single Piece Moulded Seat & Back Shell ) . Understructure Base Of Chair Round SS Pipe Structure Fixed Type . Understructure Base Fixed Type 19mm Dia SS Round Pipe 1.2mm Thick . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 780 & Depth 490mm . 440W x 410D Base Seat Moulded With PP Structure & 440W x 390H Back Seat Moulded With PP Structure . Height From Seat To Ground 420mm . All SS Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . Assembly Shell Affixed On MS Frame With Help Of Screw . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Cafe Table Top 25 mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Size 900W x 600D X25H . Base Rectangular Ms Sheet Size 380 x 380 With 8 mm Thick. Vertically 60x60 Square Pipe. 3 mm Thick Top Supporting Plate Under The Table Top. Base Supported MS Sheet . Wooden Panels Cleaning Corner Knitted Finish . Top Panels Prime Quality Board With ISI Marked . All metal components will be duly powder coated. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Supply of FOOSBALL TABLE

Supply of SNOOKER TABLE

Sub Head-II Furniture Staff Quarter

Providing wooden Queen size bed as approved by architect/Engineer-in-charge for staff quarter. (Overall Size 2000L x 1520W x 900H1 x 500H)

Side Table Top Square Type Made Of Prime Quality 19mm Thick Commercial Board Affix With 3mm Veneer At Top . Table Top Size 500W X 500D in 19mm Thick Commercial Board . Wooden Leg Size 450mm Height. Understructure Top Supported Frame & Leg Made Of Prime Quality Solid Wood. Commercial Board Use Prime Quality With ISI Marked. All Wooden Panels Cleaning Corner Knitted Finish. Wooden Panel Joint Leg To Leg Supported To Top. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STAFF QUARTER FURNITURE range for ergonomic design.

STUDY TABLE SIZE - 1200 X 600 (1200H) WITH S/B,18 MM THK LEG ,TOP-25MM TH PLPB-1500 X 600 lipped,3 DRAWER UNIT IN PLPB-400 X 450 X 680

Study table chair Size 450W x 510D x 880H. Seat & Back Plywood Made Of 12mm Hot Pressed Having Radius At Bend Supported . Understructure Base Of Chair Chrome Plated Round ERW Tube Structure Fixed Type . Upholstery Structure Prime Quality 12mm Bend Ply . Understructure Base Fixed Type 19mm Dia Round ERW Pipe 1.2mm Thick Chrome Finished . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 880 . 415W x 400D Base Seat 12mm Thick Ply & 420W x 460H Back Seat 12mm Thick Ply . Height From Seat To Ground 470mm . All Chrome Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Dining table set with 4 seating Product Dimensions Table: Length 45 Inch x Width 34 Inch x Height 30 Inch | Chair: Length 17 Inch x Width 17 Inch x Height 35 Inch. Material : Made By Solid Sheesham Wood , Table Top - Solid Sheesham Wood | Chair - Solid Sheesham Wood |

Two Seater Sofa MS-SOFA-505-2

Single Seater Sofa-MS SOFA-505-1

Table 900m dia 750mm ht. , 18mm thick PLPB Top, crome plated frame structure. Table Top 18 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade . Understructure Made Of Prime Quality 1.6 mm Thick frame. Understructure round pipe of crome platedl, Pipe 50 x 50mm With 1.6 mm Thick All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Supplying & Fixing of METHODEX make Alice CenterTable size 700x700x450mm as per drawing & specification and directed by Engineer-in-Charge. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for SERVANT HOUSE FURNITURE range for ergonomic design.

Sub-Head - I - Lift

16Passanger Lifts

Supply, Installation, Testing & Commissioning of 16Passanger Lift without machine room lift having contract speed of 1.5Meter per second serving different floors in the lift shaft of size 1800 x 2600 as per detailed specifications and as under complete with all the equipment and accessories.

Speed - 1.5Meter per second

Floors - Ground+7th Floor

Travel - 28 Meter (approx.)

Stop & Opening - 8 Stop & 8 Opening (all opening be on same side)

Controller- A.C. variable voltage and variable frequency.

Automatic Rescue Device (ARD) compete with dry maintenance free batteries as required.

Power: 415 Volts+10%, 3 Phase 4 wire 50 Hz AC system.

Car Enclosure: Stainless steel scratch proof (Moon Rock/ Honeycomb/ Hairline Finish) on all sides.

Type of Doors:

Car: Power operated, central opening, horizontal sliding stainless steel scratch proof (Moon Rock/ Honeycomb/ Hairline Finish)

Landing doors: Power operated, central opening, horizontal sliding Stainless steel scratch proof of approved shade.

A hand rail not less than 600mm long at 900mm above floor level to be fixed adjacent to control panel in the lift car.

Voice announcement system in the car to announce the position of the elevator in the hoist way as the car passes or stops at floor served by the elevator.

a) Combined luminous Hall Button and Digital Hall position indicator.

b) Battery operated Alarm Bell and Emergency Light

c) Firemen Switch

d) Infra- red Door Curtain - Full screen.

e) Integral full height car operating panel with luminous buttons with additional brail inscriptions, Digital car position indicator with Direction arrows, with overload warning indicator.

Flooring: Decorative flooring as per manufacturer's standards.

Ceiling: SS ceiling with LED lamp and fan.

Dome camera for surveillance

Passenger Lift Describe as above

13 Passanger Lifts

Supply, Installation, Testing & Commissioning of 13Passanger Lift without machine room lift having contract speed of 1.5Meter per second serving different floors in the lift shaft of size 2600x2500 as per detailed specifications and as under complete with all the equipment and accessories.

i) Speed - 1.5Meter per second

ii) Floors - Ground+7th Floor

iii) Travel - 28 Meter (approx.)

iv) Stop & Opening - 8 Stop & 8 Opening (all opening be on same side)

v) Controller- A.C. variable voltage and variable frequency.

vi) Automatic Rescue Device (ARD) compete with dry maintenance free batteries as

required.

attendant)

viii) Power: 415 Volts+10%, 3 Phase 4 wire 50 Hz AC system.

ix) Car Enclosure: Stainless steel scratch proof (Moon Rock/ Honeycomb/ Hairline

Finish) on all sides.

x) Type of Doors:

a) Car: Power operated, central opening, horizontal sliding stainless steel scratch

proof (Moon Rock/ Honeycomb/ Hairline Finish)

b) Landing doors: Power operated, central opening, horizontal sliding Stainless steel

scratch proof of approved shade.

xi) A hand rail not less than 600mm long at 900mm above floor level to be fixed

adjacent to control panel in the lift car.

xii) Voice announcement system in the car to announce the position of the elevator in

the hoist way as the car passes or stops at floor served by the elevator.

xiii) a) Combined luminous Hall Button and Digital Hall position indicator.

b) Battery operated Alarm Bell and Emergency Light

c) Firemen Switch

d) Infra- red Door Curtain - Full screen.

e) Integral full height car operating panel with luminous buttons with additional

brail inscriptions, Digital car position indicator with Direction arrows, with overload

warning indicator.

xiv) Flooring: Decorative flooring as per manufacturer's standards.

xv) Ceiling: SS ceiling with LED lamp and fan.

xvi) Dome camera for surveillance

Passenger Lift Describe as above

Car Lifts

Supply, Installation, Testing & Commissioning of Car Lift without machine room lift

having contract speed of 0.5 Meter per second serving different floors in the lift shaft

of size 6550x4010 as per detailed specifications and as under complete with all the

equipment and accessories.

i) Speed - 0.5 Meter per second

ii) Floors - Ground+7th Floor

iii) Travel - 28 Meter (approx.)

iv) Stop & Opening - 8 Stop & 8 Opening (all opening be on same side)

v) Controller- A.C. variable voltage and variable frequency.

vi) Automatic Rescue Device (ARD) compete with dry maintenance free batteries as

required.

attendant)

viii) Power: 415 Volts+10%, 3 Phase 4 wire 50 Hz AC system.

ix) Car Enclosure: Stainless steel scratch proof (Moon Rock/ Honeycomb/ Hairline

Finish) on all sides.

x) Type of Doors:

a) Car: Power operated, central opening, horizontal sliding stainless steel scratch

proof (Moon Rock/ Honeycomb/ Hairline Finish)

b) Landing doors: Power operated, central opening, horizontal sliding Stainless steel

scratch proof of approved shade.

xi) A hand rail not less than 600mm long at 900mm above floor level to be fixed

adjacent to control panel in the lift car.

xii) Voice announcement system in the car to announce the position of the elevator in

the hoist way as the car passes or stops at floor served by the elevator.

xiii) a) Combined luminous Hall Button and Digital Hall position indicator.

b) Battery operated Alarm Bell and Emergency Light

c) Firemen Switch

d) Infra- red Door Curtain - Full screen.

e) Integral full height car operating panel with luminous buttons with additional

brail inscriptions, Digital car position indicator with Direction arrows, with overload

warning indicator.

xiv) Flooring: Decorative flooring as per manufacturer's standards.

xv) Ceiling: SS ceiling with LED lamp and fan.

xvi) Dome camera for surveillance

Car Lift Describe as above

Designing, fabricating, testing, providing and fixing Ventilated Clay/Terracotta Tiles Façade system of 'UNISTONE', 'CLAYTON' or Equivalent Make in approved shade, pattern, design, texture, finish, and size of 295-400 mm X 95-100 mm in thickness of 15-20mm. The clay panels/tiles shall have Flexural Strength /Modulus of rupture average ≥ 30 N /mm2 in accordance to IS 15622:2017 E ≤ 0,08 PERCENT (GROUP B IA) (CLAUSE 6) with breaking strength ≥ 1000 N in accordance to IS 5622:2017 Part 6. The panels should have water absorption percentage by mass should be ≤ 1 % in accordance to S 15622:2017 E ≤ 0,08 PERCENT (GROUP B IA) Part 2. (CLAUSE 6) The surface scratch hardness value i.e., Moh’s scale should be Minimum 6 in accordance to IS 13630 Part 13. The clay panels should have inherent properties of being resistant to stains and chemicals. The material should be Class I material in terms of reaction to fire in accordance to EN 13501‐1 / ASTM E136. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones and duly approved and vetted by the structural consultant. The cladding panels shall be fixed on to existing cured plastered surface substrate wall treated with one or two coats of primer with appropriate Mild Steel (M.S.) rectangular/square hollow section vertical member’s framework of 50mm X 50mm or 30mm x 60mm (4.0mm thick) Mild Steel (M.S.) Substructure which shall be spaced out in accordance to the dimensions of the panel with minimum spacing of 600mm. The vertical MS framework shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns) of required size with stainless steel grade 304, M10 full threaded anchor fasteners with nylon sleeve 100mm long (for brick work) and M8 expansion anchor fasteners 75mm long for concrete surface, spacing of brackets to be based on a structural/ static calculation.

Designing, fabricating, providing, erecting and fixing ‘UNISTONE’ or equivalent non-combustible, SOLID SHEET ALUMINIUM FIN WITH MS FRAME WORK INSIDE i.e. using 6063 / T6 allow grade of M/s Jindal, Global, Nalco, Hindalco or equivalent in 1.8-2 mm (±0.3) thickness in approved size and shape and in RAL Shade in Matt Finish as approval. The RAL Shade in Matt finish on aluminium profile shall be achieved using Super Durable Polyurethane coating of specific gravity 1.6 (+/- 0.4) manufactured by M/s Jotun, AkzoNobel, Asian or equivalent under controlled conditions of heat cured for 10mins at 200 degrees’ Celsius object temperature on 4 stage PT chromated substrate to result in adhesion as per ASTM D 3359 up to average 65 micron of base coat for exterior conditions to meet or exceed qualicoat/AAMA 620 specification and warranted for UV resistance for a period of 25 years. The entire fixing system shall be designed & structurally vetted in accordance to the wind load for the location of the project and the complete system including all fixtures, screws, fasteners and all other aligned accessories, as required shall be corrosion free. The, SOLID SHEET ALUMINIUM Fin shall be fixed on the Square MS Hollow sections of 60x60x5mm / 65x65x5mm / 70x70x5mm sub frame (Red oxide Primer & Painted) along with MS Base Plate & MS Angle. MS Galvanized fasteners of M/s Trutrek, Hilti or equivalent to be used to fixed the MS Frame. The work shall be carried out as per specification, drawings and complete for all heights and levels as per direction of the Engineer-in-Charge. Note: Scaffolding wherever required to be paid separately.

Providing & Fixing High Impact and moisture, oil and UV Light resistant Heavy Duty Rubber Angled Corner Guard as per the approval from Architect for columns at parking area size W100x100mm, H1000mm & 10mm thickness. Colour and finish: Black in a uniform quality and free of any foreign substance with yellow or White Reflective Stickers Body Material: Modified Thermoplastics (100% Recycled Polymer Rubberized) Fixing: Fixed on the wall & corner of columns with six 2" Screws. Contractor to provide minimum of 5 years warranty certificate from the original manufacturer against any material and manufacturing defects. Make and Model - Frontier Polymer FCG-100D or Equivalent

Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Providing and applying hot applied thermoplastic road marking material with glass beads extremely high skid resistance 2.5mm thick with primer coat (tack coat) for binding on cement concrete road/paver blocks surface. All labour materials with special aggregates etc, as specified in B.S. part-I & II 1989 and carrying out the marking on any road on center line and other lane marking continuous for intermittent 10cm, 15 cm or 20cm width and also pedestrian crossings stripes as well as spraying further quality of glass beads of type II uniformly into a mono layer on to the hot paint line in quick succession of the paint spraying operation @ 250gms per sq.mt. area as directed and as per B.S./M.O.S.T. specification in white/yellow colour.as per the approval of Architect and drawings complete for all levels and all heights as per the direction of Engineer-in-Charge.

Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer- in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipment's and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge.

Supply and application of Polyurethane based, UV resistant, chemical resistant high abrasive resistant semi viscous liquid with 2 component material in 4:1 ratio Line marker coating shall be apply over and above of traffic coating using roller / brush. - Pedestrian pathway Arrows 150 to 200 wide / thick- Sizes and shape as per drawings, including executing in straight or curved path. (RAL 9003, Signal White - or as per mockup)

Glass Reinforced Concrete (G.R.C) Screens/ Jali Providing and fixing Glass Reinforced Concrete (G.R.C) Screens/ Jali customized as per design, dimensions as per drawings in approved shade in overall thickness of 40mm, or inner design membrane between 30-35mm and borders 50mm, casted with layering technique Power Spray methodology have weight approximately between 3.75 -4.5 Kg per Sq. Ft. The screens casting shall take place with layering methodology using- Direct Power Spray machines. The screens shall be casted from 53 grade White Portland Cement manufactured by Fine graded, sieved Quartz & Silica Sand, reinforced with Alkali Resistant Glass Fiber manufactured between 4-5% by having Zirconia content at least 16%, Super Plasticizers and UV resistant Synthetic inorganic pigments should be used for pigmentation.

DC EV CHARGER 60 KW As per Bharat EV Specification Connectors: CCS2 Dual Gun AC input voltage: AC 380V±15% AC input frequency: 45-65Hz DC output voltage: 150 VDC – 1000 VDC DC output current: 0-133 Amp Authorization: RFID, App, VIN IP55/IK10 *1 year’s warranty *5m cable *Ethernet *OCPP 1.6J *7-inch LCD screen/LED light

Cable Specification for DC Charger (60 kw):- Cu-LT Panel to EV Charger 4 Core 25 Sqmm Cu Un armoured

Supply Installation Testing Commissioning of- Main Outdoor display at entry Gate with 7X1 P10 module RGB Main Display (Outdoor at main Gate with Pole mount) Multi Row InformationDisplay ❑ Work Temp: -10° C – 55° C ❑ Multi- Color LED Matrix Display unit ❑ Voltage rating: 230 Vac, 50 Hz ❑ Currentrating: 1A, 5A ❑ Communication frequency: 9600 ❑ Luminance: 1000cd/m2 ❑ Dot matrix: 320x 120 mm ❑ LED Color: R/G/B Super bright. ❑ Communication: RS232/RS485/TCP/IPOptional ❑ Frequency: 50 – 60 Hz ❑ Cabinet Color : Black ❑ Visibility-40-50 Mtr ❑ Baud: 4800 bps/9600 ❑ Customize as persite requirement

Supply Installation Testing Commissioning of-Ultrasonic Sensor With LED, Combi ultrasonic sensors and LED lamp indicators into one device. Each parking space requires one ultrasonic combi sensor LED installed in front of the parking space. (Red & Green Color By Default other Color on request) ❑ Detection Range adjustment 2.5 m to 3 ❑ Installation location - Above front of the parking slot ❑ Horizontal – 1. 0~0.5m, Vertical- 2~3m ❑ Operating voltage - DC 10~28V (Rated 24V) ❑ Power consumption - <1W ❑ Working temperature -10°C ~ +55°C , humidity-up to 70%RH ❑ Appearancematerial- Grey ABS engineering plastics ❑ Communicationmode - RS485 ❑ Communicationmode - 2 RJ45 ports ❑ Communication distance - ≤300m ❑ Power supply distance - ≤150m ❑ Response time of the detector-After parking - 2s~10s ❑ Type of the indicator light -Red and green two-tone high-light LED ❑ Ranging error- 2cm ❑ Detection accuracy - >99.9% ❑ Communication frequency: 9600

M/S Shiv Kumar Agarwal (BID ID -336745)