Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.0 CrAccepted-AOC | ₹1.0 Cr | L1 | Accepted-AOC accepted |
| 2 | L2₹1.0 Cr+₹1,453 (0.01%)Rejected-AOC 1ST FLOOR EMMAR GRANDE KANJIRAMPARA PO TRIVANDRUM 695 030 | THIRUVANANTHAPURAM | THIRUVANANTHAPURAM | KERALA | 695030 | ₹1.0 Cr+₹1,453 (0.01%) | L2 | Rejected-AOC accepted |
Tender Value
₹1.0 Cr
EMD Value
₹50,000
Closing Date
27 Jul 2022, 3:00 pmClosed
Executive Engineer
Electronics Division Thiruvananthapuram
Construction of Central Jail at Thavanur in Malappuram District - Electronics Works Phase 1(Balance Work)
2022_PWD_499404_1
15/EEELCSTSR/2022-23
Open Tender
Miscellaneous Works
Item Rate
90 days
Thavanoor
Please refer Tender documents.
7 documents required · 7 mandatory
₹5,520
₹50,000
5 Nov 2022
14 Jul 2022
29 Jul 2022
14 Jul 2022
27 Jul 2022
14 Jul 2022
Amount
CCTV Surveillance System
Supply, Installation, Testing and Commissioning (SITC) of 1080P HD Weather Proof (IP66) vandal proof Fixed 2.8 ONVIF IR Bullet onvif PoE camera with 128Gb surveillance grade SD card compatible with the camera for edge storage, include additional Weather shield for rain protection, including 3 years OEM on site warranty as per the specifications in Item No.2 of Specification chart including termination charge and charge for RJ45 connector Accepted make: Samsung, Mobotix, Milesight, Honeywell
Supply, Installation, Testing and Commissioning (SITC) of 1080P HD - PTZ Camera, Support PoE (optional), SD card, up to 256G, Optical Zoom min 20X or Better specification. including 3 years OEM on site warranty as per the specifications in Item No.3 of Specification chart. including termination charge and charge for RJ45 connector Accepted make: Samsung, Mobotix, Milesight, Honeywell
Supply, Installation, Testing and Commissioning (SITC) of 1080P HD Weather Proof (IP66) vandal proof, vari focal of 3.2-10mm motorized , ONVIF IR Dome PoE camera with 128Gb surveillance grade SD card compatible with the camera for edge storage including 3 years OEM on site warranty as per the specifications in Item No.1 of Specification chart including termination charge and charge for RJ45 connector Accepted make: Samsung, Mobotix, Milesight, Honeywell
Supply, Installation, Testing and Commissioning (SITC) of Network video recorder with 64 IP channels with N+1 Redundancy Fallover NVR with 8 HDD SATA Slot , Recording bandwidth Up to 300 Mbps., Etc or Better specification. including 3 years OEM on site warranty as per the specifications in Item No.4 of Specification chart. Accepted make: Samsung, Mobotix, Milesight, Honeywell
SITC of 8TB Surveillance Internal Hard Drive - 7200 RPM Class, SATA 6 GB/S, 256 MB Cache, 3.5" Make: Western Digital/Seagate/Samsung
SITC of 24-Port Gigabit PoE+ Smart Switch with 2 SFP Ports and Cloud Management system with 380 watts minimum power budjet and minimum specification of - 24-Port Gigabit with PoE+ and 2 dedicated Gigabit SFP fiber uplink ports, Layer 2 features, Non-blocking switching with 52Gbps, IPv6 management: IPv6 QoS, IPv6 ACL, IPv6 Multicast, and static and dynamic IPv6 address assignment, Etc or Better specification. Make: Netgear/Cisco/Juniper
SITC of Stackable Managed Switch with minimum specification of 24-port 10GBASE-X (SFP+) , 2-port 10GBASE-T (RJ45) (shared, back), 480Gbps non-blocking fabric across 24 ports, Out-of-band 1G Ethernet management port, USB /RJ45 /RS232 console ports and USB storage port, Full L3 feature set and non-stop forwarding (NSF) stacking, Switching Capacity - Up to 480 Gbps, CPU- 800 Mhz 1GB RAM 256MB Flash or more, VLANs - Static, Dynamic, Voice, MAC, GVRP/GMRP, Double, VLAN mode- Private VLANs, Etc or Better specification. Make: Netgear/Cisco/Juniper.
90.10.1.1 -Supply & Fixing the following types/ sizes of boxes along with modular base & cover plate for modular switches in surface/ recess including making good the damages, colour washing etc. as required (RoHS compliant ) 126mmx125mmx55mm (5” x4.9”x2.2”) 0.72kg(1.6lb) 1 or 2 module moulded plastic box on surface
Supply & Fixing of Galvanized L shape Bracket half meter for Fence Boundry Cameras specially designed Make: Tata/ Jindal/JSW
Supply & Fixing of Galvanized I shape hanging Bracket two and half meter for Cameras specially designed Make: Tata/ Jindal/JSW
SITC of Optical Fiber Transceiver with minimum specification of - Dual data-rate of 1.25Gbps/1.063Gbps operation, 1310nm FP laser and PIN photo detector for 20km transmission, Compliant with SFP MSA and SFF-8472 with duplex LC receptacle, Digital Diagnostic Monitoring - Internal Calibration or External Calibration, -0 to +70°C, RoHS. Make: Netgear/Syrotech/Cisco.
SITC of Optical Fiber Patch Cord, LC-LC, 50/125 Micron, LSZH Duplex, 03 Mtr Make: FINOSEL/AMP/MOLEX
SITC of Floor mount Cabinet, 42U FS 4xfans, Vertical organizer,wheels, FD Glass and Rear Double Doors 800x1000 for Core Data Center Make - Netrack/Rittal/Valrack.
SITC of Fiber Shelf, 1U PP 12 Adapter Duplex, 2 Tray Make: FINOSEL/AMP/MOLEX
SITC of Fiber Pigtail, LC- 50/125 Micron, LSZH, 1.5 Mtr Make: FINOSEL/AMP/MOLEX
SITC of 6 Way Power Distribution Unit , Universal Type Make: FINOSEL/MOLEX/AMP
SITC of Fiber Front Panel, For 600G2 Panel Type 12 Dplx SC, 600-24SC-DPLX-00 Make: FINOSEL/MOLEX/AMP
SITC of fiber optic Coupler Make: FINOSEL/AMP/MOLEX
SITC of Video Management Server Computer, Core i7-7700 8GB RAM 1TB HDD including all I/O Devices Make: Dell Optiplex 7050 MT
SITC of Surviellence Display Unit 4K Ultra HD LED Smart TV, Video wall compliant 50" or above Make: LG/SAMSUNG/PANASONIC
od34601/2020_2021 - SITC of 26-Port or above Gigabit Smart Managed Switch(24 Gigabit + 2 SFP) with 52Gbps forwarding capacity, 16K MAC Address Table, RoHS compliant. Rack mountable and having Lifetime warranty, Etc or Better specification. Make - Netgear/Cisco/Juniper.
od34609/2020_2021 - SITC of fully loaded 24 port cat-6 Patch Panels conforming to relevant standards for interconnecting of servers and nodes including termination charge at both ends. Make - Finosel/AMP/Molex.
od34615/2020_2021 - Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof Wall Mount 9U Rack for switches, Patch panels and accessories including cable manager(x2), AC Distribution box(x1), cooling fan(x2) and hardware mounting kit. Conforms to DIN41494. Make - Netrack/Rittal/Valrack
od34629/2020_2021 - SITC of CAT-6 , 2 meter Patch code for interconnecting information outlets and computers.4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, RoHS Compliant. Make - Finosel/AMP/Molex.
od34627/2020_2021 - SITC of CAT-6 , 1 meter Patch code for interconnecting Patch panel and Switch.4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, RoHS Compliant. Make - Finosel/AMP/Molex.
od34625/2020_2021 - SITC of CAT 6 RJ 45 modular Keystone jack in the existing front plates and giving necessary connections as required (RoHS) Make: AMP/Molex/Finosel
1.21.1 - Supplying and fixing of following sizes of medium class ivory color PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm
1.21.2 - Supplying and fixing of following sizes of medium class ivory color PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required-25 mm
1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required. 4 pair UTP CAT 6 MOLEX/AMP
EPABX and LED TV
Supply, installation and commissioning of Digital EPABX with the following minimum features: Trunk lines - 4, Extension capacity -Max 32, Printer interface, intercom, call transfer, Modem , Fax connectivity, incoming /outgoing call buffer, call back to last incoming caller, VIP call with distinctive ring patterns, Camp on-No Reply/Busy etc. including crone module and giving connection to all existing extension lines and co lines, future expansion capability up to 52 extensions. Make - Syntel Neos/NEC/Panasonic.
od30285/2020_2021 - SITC of push button telephone equipment featuring Caller ID, Ringer volume control, Tone/Pulse switchable , Ring indicator, flash/pause functions, last number redial, microphone mute etc. Make - Panasonic/Motorola/Betel.
od30287/2020_2021 - SITC of push button telephone equipment featuring Ringer volume control, Tone/Pulse switchable , Ring indicator, flash/pause functions, last number redial, microphone mute etc. Make - Panasonic/Motorola/Betel.
od30289/2020_2021 - SITC of CAT 6 RJ 11 modular Keystone jack in the existing front plates and giving necessary connections as required (RoHS). Make: AMP/Molex/Finosel
Supply and installation of 50 pair krone module with enclosure. Including giving connections to in and out cable pair already wired. Make: Molex/ADC KRONE
od30418/2020_2021 - SITC of full HD 43" LED Smart TV including 3 years OEM warranty having Android OS, built in WiFi, 1920x1080, 108cm(43), HDMIx2, USBx2, 16W Speaker output.
PA System at Auditorium
Supply and Installation of exceptional quality 1100 Watts Speaker box, with minimum Specification of - 2 x 15" Three way full rang Speakers with trapezoidal cabinet incorporates a 2-inch exit throught with high frequincy compression Driver, Frequency Response: 70 Hz-18kHz. Low & Mid Frequency - 1*15" (381mm) Diameter, Voice Coil - Diameter 1x 3" (77mm), Voice Coil Material - Copper, Magnet Material - Ferrite, Chassis Type - Cast Aluminum, Cone Surround - TSV, Former Material - Glass Fibre, Input Power Rating - 2*500 Watts Continuous. Pink Noise, 2*1000 Watts Program, 2*2000 Watts Peak, Bandpass Sensitivity - 96dB SPL (1W @ 1m), etc., Accepted model - POPE LD-215 or equivalant.
Supply and Installation of Class H Architecture 4000 W @ 4 ohms 2 Channel Power Amplifier with minimum Specification of - Frequency Response - ±0.1 dB from 20 Hz to 20 kHz at 1 watt, Phase Response - ±10 degrees from 10 Hz to 20 kHz at 1 watt, THD - 0.05%, Intermodulation Distortion - (IMD) <0.35% (60 Hz and 7 kHz at 4:1, from full rated output to -30dB), Signal-to-Noise Ratio - >105 dB A-weighted or 100 dB unweighted below rated power, 20 Hz - 20 kHz, CMRR - (20 Hz to 1 kHz) > 55 dB, typically > 70 dB, Crosstalk - > 80 dB (below rated power, 20 Hz to 1 kHz), Slew Rate - 80V/usec, Damping Factor - >2,000 from 10 Hz to 400 Hz, Input Sensitivity gain - 0.775 / 1 / 1.44 Volt, Output Circuitry - Class H Protection etc., Accepted model - POPE MAC-8202 or equivalant.
Supply and Installation of 2way bi-amplified Active Stage Monitor with 120 dB SPL, 400 Watts continuous, 1 x 15" Two way speaker, 200Watts Peak 1.35" HF driver, Frequency Response: 40 Hz-20kHz1.9 kHz Crossover Frequency. High Frequency - 1.35” Compression Driver, Voice Coil Diameter - 25 mm (1"), Magnet Material - Ferrite, Diaphragm Material - Titanium Low Frequency -1*15" (381 mm) Diameter Transducer, Voice Coil Diameter - 76 mm (35"), Box Construction - Weather Proof ABS Cabinet. Accepted model - POPE FP-215A or equivalant.
Supply and Installation of 12-Channel Mixing Console with minimum specification of Max. 6 Mic / 12 Line Inputs (6 mono + 3 stereo) / 1 Stereo Bus / 1 AUX (incl. FX), 1 Stereo Bus, 1 AUX (incl. FX), “D-PRE” mic preamps with an inverted Darlington circuit, 1-Knob compressors, High-grade effects: SPX with 24 programs, 24-bit / 192kHz 2in / 2out USB Audio functions, Works with the iPad (2 or later) through the Apple iPad Camera Connection Kit / Lightning to USB Camera Adapter, Includes Cubase AI DAW software download version, PAD switch on mono inputs, +48V phantom power, XLR balanced outputs. Accepted Make: YAMAHA MG 12XU or other brand having equivalent or better specifiction
Supply and installation of cardioid Microphone with 40Hz to 18000Hz frequency response . Accepted Model: Sennheiser e 835S or equivalent
Supply and Installation of Proffessional series Wireless Microphone System with Required cables clip and pouch Etc. Accepted Make: Studiomaster XR80HL or other brand having equivalent or better specifiction
Supply and installation of hyper cardioid Goose neck Microphone with base and power supply for porving phatom power.Accepted Model: studio Master Flex 4 or equivalent
Supply and laying of 10 Mtr high quality shielded XLR cable for connectin Miccrophones and Audio mixer.
Supply and laying of 2 Mtr high quality shielded XLR cable for inter connections in System Rack.
Supply and installation of complete steel/Aluminium constructed 27 U or higher system Rack with Acrylic Door, lock & Key, and Power Strip for placing all Equipments. Recomended Model - Netrack or Equalant.
Supply and Installation of Power Distribution Unit with required of PVC Insulated and Sheathed 650/1100 grade 3 core 4mm Copper conductor with 10 Numbers of German type 16 Amps Power socket and required accessories.
1.17.11 - Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 2.5 sq. mm
1.21.1 - Supplying and fixing of following sizes of medium class ivory color PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm
Supply and installation of Microphone Floor type stand with 12" Goosneck Height of 920-1500 mm. Accepted Make: AHUJA AFS201 or other brand having equivalent or better specifiction.
Supply and installation of wall/floor mount speaker stand 70kg cappacity for 1100Watts Speakers.
Supply and Fixing of good quality flight Cases strengthed with alluminium/steel structures for Monitor speakers.
Supply and Fixing of good quality flight Cases strengthed with alluminium/steel structures for keep Microphones and cables.
General Announcement System
90.15.3.1 Supply installation testing commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x12mm suitable for wind speed as per IS 875 Part III single arm bracket 0.5mt including connector foundation bolt 4 nos fixed in existing RCC foundation and junctions box etc.complete 5 Meters
90.16.2.2 Supply and laying of the following sizes of B class GI pipe laid 0.6 m below ground level including excavating trench of suitable size and refilling etc, as required.20 mm dia. G.I pipe ( medium class)
Supply and Installation of 480 watts Class H Circuitry 6 Zone Mixer Power Amplifiers, with minimum specification of 3 Mic, 2 Aux, Media Player, Bluetooth, 3 zone with on/off, 3 zone with volium knobs, Chim for publc Address, Priority control, Low & High Impedance speaker output,Frequency response: 50 – 20,000Hz (±3dB), Tone control(both Bass & Treble), 12/24V Output for broad cast emrgency annoucements, 70V/100V inputs and Outputs . Make: POPE PA-480ZM or Eqvt.
od30400/2020_2021 Supply, conveyance, installation, testing and giving connection of wall mounting 2 Way Speaker Box of 10 Watts rms , Power taps of 10W/5W on 70V/100V, frequency response 140 - 15000Hz Make: POPE/BOSCH/TOA
od30406/2020_2021 - SITC of High quality, heavy duty paging microphone having 50-1500 Hz frequency response, 500Ohm impedence and 2.2mV/Pa sensistivity with Strong, robust and stable base incorporates separate push swithces for momentary and locked use. It should have Strong flexible 10” gooseneck is securely fixed to the aluminium die-cast base. Make:POPE/BOSCH/TOA
Supply and Installtion of 8 channel Professional Splitter/mixer with individual mute and controllers. Make: Yamaha/Studiomaster
Supply and installation of 2 M Audio Signel extension cord used to connect between Amplifiers and Mixer unit.
Supply and installation of complete steel/Aluminium constructed 27 U or higher system Rack with Acrylic Door, lock & Key, and Power Strip for placing all Equipments. Make: Netrack or Eqvt.
Supply and Installation of Power Distribution Unit with required of PVC Insulated and Sheathed 650/1100 grade 3 core 4mm Copper conductor with 10 Numbers of German type 16 Amps Power socket and required accessories.
1.17.11 - Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 2.5 sq. mm
90.12.10.2 - Supply & laying of DWC pipes made out of HDPE conforming to IS 14930 Part II for mechanical rotection to underground power cables with all required accessories in ordinary soil 0.75m below ground level including excavation50/38 mm or nearest size
90.16.1.2 - Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG)
5.2 - Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required
Adtech Systems Limited
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .