SPECIAL REPAIR TO BLDG NO 03-T (FAMILY WARD) AT MH LANSDOWNE

Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:-

Area not exc 1.5 sqm each

Area exc 1.5 sqm but not exc 4 sqm each

Area exc 1.0 sqm and not exc 2.0 sqm each

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable and variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

65 mm x 100mm size

65 mm x 125mm size

M&L for 30 mm thick factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood owder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, acomplete all as specified and directed.

M&L for 30 mm thick molded WPC wire mesh factory made 1005 decorative type, moulded, panel door shutter prepare to receive Mesh, gauze etc (single or two panel Including wire mesh(confirming as per IS: 4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with wood grain texture and back side plain with density not less than 600kg/cum manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, termite proof, fire retardent and having screw holding capacity.complete all as specified and directed.

S&F MS butt hinge, medium weight, cold rolled and fixed of following size complete all as specified and directed:-

100 mm long

S&F 250 mm long anodised aluminium sliding door bolt (ISI marked) with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of following size complete all as specified and directed:-

S&F 150mm anodised aluminium handles cast type complete all as directed and specified

S&F 150 mm long anodised aluminium barrel tower bolts (ISI marked) of extruded section complete all as directed and specified

S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F including fabricating of aluminium colour powder coated having minimum thickness of powder coating 50 micron for door / window/ ventilator frame, shutters & partition including necessary joining cleats, glazing clips, aluminium snap beading having minimum wt 100gm/RM, rubber neoprene gasket, screws, dash fasteners, rawel plug for fixing of screw in wall or floor etc., aluminium sections as approved by GE complete all as specified and directed. Note : - (i) Builders Hardware shall measured and paid separately under respective item of Schedule 'A' . (ii) Only weight of aluminium section shall be measured and paid. No claim what so ever shall be entertained by the Govt on this account. (iii) Thickness of section shall not be more than 2mm. (iv) Window shall be fabricated as per requirement with provision for AC / Cooler openning.

S&F aluminium coloured powder coated door/ window (sliding type)/ventilator shutterswithout sash bar aluminium section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised aluminium snap beading screws etc complete all as specified and directed.

S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium Ventilator/window/ incl necessary cutting / moulding and chamferrring of edges for service window/counters complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or wire staples complete all as specified and as directed.

Supply and fix 7 mm thick aluminium coloured power coated grill of Deco Grill pattern DG 104, fixed in aluminium windows / ventilators, etc.including necessary aluminium channels in openings of windows / ventilators, complete all as specified and as directed.

Demolition of wall and ceiling boards ( fibre, pulp insulation etc.) or insulation boards/ slabs/ blankets of any thickness, including cover fillets complete all as specified and directed.

S&F false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm With Semi perforated 12mm thick micro tegular edged or 10 mm thick square edged of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

M&L E-boards, ceiling 4 mm thick with J framed work with main Tee of size 24 x 28.5mm made out of PGI sheet 0.3 mm thick double at web and single at flange and the flange coverd with powder coated sheet 0.25 mm thick and wall angle 24 x 24 x 5 mm powder coated for ceiling and the ceiling boards 60 cm X 60 cm X 4 mm thick, suspended with GI wire 2 mm dia and 2 m average lenght with adjustable hanging device complete including plugging in brick / stone walls with steen rawl plug @ 600 mm C/C and the ceiling boards shall be pressed to the ceiling tee with staple clips at all four sides and painted with two coats of oil bounds distemper after preparation of surfaces including making good all the disturbed portion complete all as specified & directed.

S&F 5mm thick Prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and as directed.

S& F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed. .

S&F in repairs for stainless steel non magnetic curtain rod of 25 mm dia with and including fixing brackets and decorative type knobs (as approved by AGE (I)/ GE )both side of each rod complete all as specified and directed. Note: - Measurement will be taken between end point of knobs.

S&F 18 mm thick with min density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour fixed with ss screws and solvent cement/ adhesive to make kitchen cabinet shutters including D Type handle & Piano hinge for fixing the shutter complete as per manufacturer’s instructions complete all as specified and directed

S&F continuous (piano) hinges, mild steel bright finish or electro galvanised width of flaps (when open) 30mm complete all as specified and directed.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for walling of random rubble masonary, uncoursed well bonded, bedded and solidly hearted, brought upto courses, built in cement mortar (1:6) complete all as specified and directed. Note :- Only quantity of PCC bond stone to be deducted from quantity of random rubble masonary.

Description same all as item No. 27 above but except stone complete all as specified and directed. Note :- Old retreived serviceable stone under demolition item shall be used.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surfacae not exceeding 40mm to face stone for Lime or sand stone and dressing of face beds and joints, as specified of random rubble walling, uncoursed or brought upto course complete all as specified and directed.

M&L for raised pointing in cement mortar (1:4) to random rubble masonary uncoursed or brought upto course complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises from MoD land complete all as specified and as directed.

M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8mm thick, as in dado etc including 10 mm thick rendering in CM (1:4), set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed. Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I)

M&L for non skid, joint free, coloured ceramic tiles 7-8mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15 mm thick screed bed in CM (1:6), area of each tiles shall be of following complete all as specified and directed :-

Area of each tile exc 0.06 Sqm but not exc 0.18 Sqm.

Area of each tile exc 0.18 sqm but not exc 0.36 sqm.

Area of each tile exc 0.36 sqm but not exc 0.72 sqm.

All as per Item No. 34.01 but 10 mm thick backing coat on fair faces of brick work in CM 1:4 in skirting complete all as specified and as directed.

All as per Item No. 34.02 but 10 mm thick backing coat on fair faces of brick work in CM 1:4 in skirting complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, WHB counter and like bedded over and including 20 mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 60 mm thick coloured rubber moulded glossy finish machine pressed precast concrete interlocking paver block, M-35 Grade with pre-polished, coloured/ laquar finish any shape and size, as approved confirming to IS 15658-2006 with and including over 50 mm thick stone dust/ sand cushining complete all as specified and directed.

M&L for 30cm x 30cm x 30 mm thick rubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed

M&L for mirror polished machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror finish polishing over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

M&L grinding & wax polishing to mirror finish to old kota stone slab flooring & steps, mixed with pigment to match the shade of slab complete all as specified and directed.

Demolition of PCC in ground floor and pavings not exc 15 cm thickness below or above ground level including removal of rubbish out side MOD land complete all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed.

M&L for 10 mm thick plastering on brick or concrete surface in CM (1:6) surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick plastering on other than fair faces of brick wall/concrete surfaces in CM (1:4), surface finished even and smooth without using extra cement mixed with WPC as per manufacturer's instruction complete all as specified and directed.

뤀က
♍⁌牰灥牡瑡潩景渠睥祬瀠慬瑳牥摥猠牵慦散漠⁦硅整湲污眠污祢愠灰楬慣楴湯漠⁦洱桴捩慷汬挠牡⁥異瑴⁹潴爠浥癯⁥桴⁥敤瑮愠摮琠慭敫琠敨猠牵慦散攠敶湡⁤浳潯桴戠⁹牧湩楤杮漠⁲畲扢湩⁧楷桴猠湡⁤慰数⁲湡⁤灡汰楹杮吠潷漠⁲潭敲挠慯獴漠⁦〱┰倠敲業浵愠牣汹捩攠畭獬潩慰湩⁴愠摮椠据畬楤杮瀠楲業杮挠慯⁴景攠瑸牥潩⁲牰浩牥愠灰楬摥

M&L for preparation of newly plastered surface of internal wall by application of 1mm thick wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer using roller all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge.

M&L preparation of old surface of External wall by application of 1mm thick wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying Two or more coats of 100% Premium acrylic emulsion paint and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm including water proofing compound (200ml/bag of cement) over one coat of putty (if required) complete all as directed. Note- Putty shall be measured and paid seperately.

Material & Labour for preparation of old surface of internal wall and applying two coats of oil emulsion distemper over putty (if required) make the surface even and smooth of all as specified and prescribed by manufacturer of paint and all as directed. Note- Putty shall be measured and paid seperately.

M&L for 1 mm thick Acrylic/WaterProofing Wall Putty & surface finished even and smooth with sand paper complete all as specified and directed

Dismantling of timber scantling such as in fillets, rails, runner, rafters, purlins etc under 40 sqcm in section as in un framed work complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F rolled mild steel section for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

Dismantling of timber scantling 40 sqcm and over in section, in any position as in framed work complete all as specified and as directed.

M&L for second class hard wood (sal) in timber scantling (clean sawn) as in framed work, roof truss etc complete all as specified and as directed.

S&F for 20 mm thick 2nd class hard wood boarding planed one side with butt joints and fixed with nails as in roofs, ceiling partition fascia, barge soffit etc (except flooring and skirting) including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed

M&L for two coats of synthetic enamel paint over a coat of pink primer including preparation of new wood or wooden base surface over 10cm width or grith complete all as specified and directed.

Demolition and breaking up drain pipes (PVC/ SGSW/ AC/ RCC pipe) of following bore of pipe, set in cement mortar complete all as specified and as directed:-

150 mm bore

110mm bore

75 mm bore

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

110 mm bore

75 mm bore

110 mm bore

75 mm bore

110 mm bore

S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic seat and cover, white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) including S trap 110 mm connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., complete all as specified and directed.

S&F vitreous china counter top wash hand basin, of size 490 x 400 x 145 mm excluding taps, waste pipe but including waste coupling complete all as specified and directed.

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe for IWC/EWC 32mm dia of make as approvrd by GE complete all as specified & directed.

S&F in repair PVC connection 15 mm size 450 mm long with PTMT nut complete all as specified and directed.

Taking up or down steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed :-

15mm bore

20mm bore

S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :-

15mm bore

20mm bore

S&F in repairs 15 mm bore bib taps, chromium plated, fancy type, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed .

S&F in repairs 15mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle or concealed screwed both ends for iron pipe or for unions complete all as specified and directed. Note for all CP item :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S&F in repair CP overhead shower 100 mm round/Square shape single flow (ABS body chromium plated with gray face plate) with rubit cleaning system fixed in 15mm bore of pipe complete all as specified and directed .

S&F 15mm dia brass CP wall mixer with provision for over head shower for mixing hot and cold water screwed down for iron pipe and fixed including taking down existing bib tap complete all as specified and directed.

S&F 15mm dia chromium plated central hole wash hand basin mixer without PWS with 450mm BRAIDED HOUSE hose screwed down high pressure screwed for iron pipe including taking down existing bib tap completed all as specified and directed .

S&F in repair chromium plated brass towel rail, 20mm dia, 60 cm long between flanges complete all as specified and directed.

S&F in repair stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx 330mmx160mm complete all as specified and directed.

150mm bore

150mm bore

Demolition of RCC n'exc 15cm thick (below or above grong level) including cutting of reinforcement to facilitate demolition complete all as specified and directed. Note : Reinforcement obtained from demolition will be considered credit Sch as scrap iron.

M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:4) including necessary fair finish formwork complete all as specified and directed.

M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in floor/ roof beam, cantilevers, lintel over 1.5m span complete all as specified and directed.

M&L for formwork for rough finish to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete and all as specified and directed.

M&L for PCC (1:3:6) Type C2 (40 mm graded aggregate) as in foundations, filling and mass-concrete complete all as specified and directed.

M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

Dismantling and taking down old unserviceable point wiring of any type (light, fan, socket, power etc) complete with fitting such as switches, sockets, ceiling roses, pendants, lamp holders, light fitting etc including CI/ pressed steel terminals, switch box and making good the disturbed surface of wall/ floor etc to match with the existing surfaces of wall/ floor complete all as specified and directed. Note :- (i) If the contractor fail to make good the disturbed surface of wall/ floor etc and do not match with the existing surface of wall/ floor to the entire satisfaction of Engr-in-Charge, a recovery of @ Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute, the decision of Accepting Officer will be final and binding. (ii) Old fittings/ fixtures / accessories like switches, sockets, lamp holders, regulators etc., if found in serviceable condition shall be removed carefully for reuse in the work or taking on charge. (iii) Only old unserviceable items will be considered in credit Sch.

M&L for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continuous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed rigid PVC conduit(ISI marked) ,duly cutting chases & concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) including metal flush box made of GI sheet and white cover with making good the disturbs surfaces of wall/floor/ceiling complete all as specified and directed for the following. Note: Flush box and cover plate should be of same make all as approved for switches/sockets.

One light/fan/bell point controlled by one No modular type switch 6 Amps single pole one way

One 3 pin 6 Amps socket outlet on same board controlled by one, one way 6 Amps modular switch.

One socket outlet 5/3 pin 6 Amps controlled by one modular switch on independent board.

Per point

S & F switch Modular single pole, one way 6 Amps , 1 module, 230 volts, 50 hz complete all as specified and directed.

S&F modular switch bell push button type, 1module, 6 Amp single pole complete all as specified and as directed.

Supply and fix Modular switch 1 way 16 Amps, 1 module, 230 volts, 50 Hz complete all as specified and directed.

Supply and fix Modular Socket outlet, 6A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed.

Supply and fix Modular Socket outlet, 16A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed.

S&F bell electric DING DONG type, AC, 230V single pole, 2module complete all as specified and as directed.

S&F fancy Lamp holder (with metal ring), insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fitting complete all as specified and as directed.

S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as speccified and directed

S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed

DB SPN, 8 way

DB SPN, 12 way

S&F MCB DB TPN 4 Way connecting & testing distribution board of sheet metal enclosures double door, 415 volts rated copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed

S&F MCB , SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F MCB, TPN, AC, 415 volts of 63 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F surface mounted LED luminiare, 10 watt 2 feet with all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed. Note: The firm has to give warranty for fitting including driver minimum for 2 years for any defects developed during the period.

S&F surface mounted LED luminiare, 20 watt 4 feetwith all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed. Note: The firm has to give warranty for fitting including driver minimum for 2 years for any defects developed during the period.

S&F LED bulb 10 watt (Cool day light) having colour temp 6500 K and lumen out put 950 suitable for B-22 type to fix on batten holder complete all as specified and directed.

S&F sub main wiring two single core 6 Sqmm PVC insulated, unsheathed, stranded copper conductor cable(FRLSH) 1100Volts grade drawn in & including rigid PVC Conduit 20 mm dia or more medium grade concealed in wall along with 6.00 Sqmm PVC insualted unsheathed copper conductor cable (FRLSH) as earth wire and wire connected with main earth dolly including cutting chases and making good disturbed portion complete all as specified and directed. Note : Two runs of phase, neutral wire and one run of earth wire and PVC conduit will be measured as one RM or one length.

S&F in repair Exhaust fan plastic body AC single phase 230 Volt of size 300 mm sweep complete with blade, Frame and louvers including making hole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed. Old Exhaust fan to be deposited in MES Store

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4mm GI Wire check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI strip upto 7.5 mtrs long with 15 mm dia medium grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI strip more than 7.5 mtrs will be measured and paid seperately under relevant items.

S&F earth continuity conductor or main earthing lead fixed to walls or to poles or any other indicated situation for loop earthing with using 4mm dia GI earth wire complete all as specified and directed.

S&F OFF load change over switch 415 V in sheet metal enclosure 4 pole of capacity 63 Amp complete all as specified and directed.

Please Enable Macros to View BoQ information