PROVN OF MEDICINE SHED AND TRAINING SHED NEAR VARIOUS BLDG OF 57 FMSD UNDER AGE B/R-II OF GE (A) NO. 2 JODHPUR

Excavation in Post holes each , not exceeding 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm , watering, and removing surplus soil to a dist n. exc 50 m and making good surface in any type of soil.

M&L, PCC (1:2:4) type B-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

S & F Rolled miled steel in Joist, channel, angle, or tee sections, fixed independently,including base plate, horizontal tube section with welding and required work for fixing etc. AFe- 290 (Gde E-165, all as directed by Engineer-in-Charge.

S&F Rolled mild steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. (Fe 410-w (Gde-E- 250 quality- A) incl painting one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication all as specified.

M&L for pre painted galvatume aluminium zinc GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering fixed with J or L hooks complete all as directed.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165

M&L prep of new steel surfaces & applying 02 coats of syn enamel paint over a coat of red oxide primer.

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m deep for foundation etc.and getting out in soft loose soil.

M&L PCC in foundations, filling and mass-concrete type D2 (1:4:8) using 40 mm graded stone aggregate

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified.

M&L Rendering 15 mm thick CM 1:4 on other then fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L Preparation of new plastered and appling two coats of cement based paint over a coat of primer complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers as specified and directed.

Removing excavated soil materials n.exc 50m and depositing where directed at a level, complete all as specified.

M&L for Cement concrete type D-2, 1:4:8 (40mm graded aggregate) 150 mm thick as in sub bse for floor etc.

M&L Cement concrete 1:2:4 type B1 using 20mm graded agg 50 mm thick for laying of floor etc complete all as specified and directed

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

S&F Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Dismantling of stone/ brick work masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work, serviceable stone aside for reuse and removing unserviceable material in low laying area complete all as specified and as directed.

M&L for squared rubble walling jodhpur type, brought upto course, well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

-ditto- all as per item 21 above but, except stone complete all as specified and as directed.

Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed.

M & L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated sheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces ) conduit of size 20 mm or med grade as required as site, totally concealed in walls / floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, all as specified, directed and shown on drgs for The rates of chase cutting on wall done concealed conduit and steel terminal boxes are included in the unit rates all as specified and directed by Engr-in-Charge for One light / exhaust fan point controlled by one no, 1-way, 5 Amps switch.

All as per item ser No 24 above but for one socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

S&F of Switch piano type, single pole, one way, 5 amps, 230 volts, complete all as specified and directed. Make : Havells (Rio) / Cona / SSK

S&F of Socket, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, complete all as specified and directed. Make : Havells (Reo) / GM / SSK

S&F of Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed. Make : Havells (Rio) / GM / SSK

S&F of surface and wall mounted LED tube light fitting 20W, 4 ft long, 220 Volts , extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver incl connecting to ceiling rose with three core twisted flexible copper cable of suitable size complete all as specified and directed by Engr-in-Charge.

S&F of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE 5 star rated with Brush Less Direct Current motor (BLDC).

S&F Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN DB 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Make : Schneider Elect / Legrand / C&S / Hager

S&F MCB, B Curve type, 10 kA, 40 to 63 Amp, SPN with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Hager

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Hager

Supply, laying, testing and commissioning of LT UG cable, XLPE insulated, PVC sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 10 sqmm 2 core, suitable for earthed system, laid in duct/trench/along pole/wall etc including nuts, bolts, washers, saddles & screws etc and making connection, complete all as directed. Note : 1. The cost of Al thimbles/lugs and cable gland etc is included in quoted rate and no extra payment will be made for it. 2. Excavation, earth work, sand cushioning and brick protection will be measured and paid separately under respective items.

M&L for factory made un-reinforced pre cast concrete cable protection cover LV class type - I with size 250mm x 150mm x 40mm laid across the cable (i.e. width of cover along the length of cable) for UG cable protection on the top of the sand cushioning, complete all as specified and directed by Engr-in-Charge.

M & L for fine dry river sand cushioning by laying 8cm thick layer below the cable for making soft bed and 15 cm above the cable and then punning down to its consolidated thickness of 18cm after the cable is laid all as specified in SSR Part I and as directed.

Supply and lay 40 mm bore galvanised steel tubing Light grade with all fittings and fixtures laid in trench or ceiling or laying in floors complete all as directed.

M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed.