SPECIAL REPAIRS TO KOQ 27 IN PHASE I AREA AND BLDG NO P 54 AT NAVAL STATION BHEEMUNIPATNAM PROVISION OF CERAMIC VITRIFIED TILES AND GRANITE IN SHIPS GALLEY AND OFFICE ENCLOSURE IN BOSUN STORE AND 02 NOS SPLIT TYPE AIR CONDITIONER UNITS OF CAPACITY

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Demolition of Unreinforced Cement Concrete in other than ground floors), beams, staircases, landing, chajjas and similar suspended work.

Taking down chowkats with shutter (without taking off shutters from the frame) exc. 1.50 Sqm and n.exc.4.00 Sqm each all as specified and directed.

Taking down plastering on brick or stone wall,etc including raking out joints,hacking for key,scrubbing down with water etc all as specified and directed.

Taking down shutter exc. 1.00 Sqm and n.exc.2.00 Sqm each all as specified and directed.

M&L for 10 mm thick rendering on brick work or concrete surfaces in cement mortar 1:6 complete all as specified and directed

M & L for Non skid/matt finish ceramic tiles 7 to 8 mm thick of size exc 0.11sqm but not exc 0.18sqm, as in floors etc.set and jointed in neat slurry and pointed in white or coloured cement to match for joint free over screed bed or bedding layer of mortar 15mm thick in CM 1:4.

M&L for Vitrified ceramic tiles 10mm thick (square or rectangular) of dark shade, polished,area of each tiles not exc 0.36Sqm, as in floors etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM (1:4).

M & L for Glazed ceramic tiles in vertical surface(skirting) 250 x450 or 300 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match for joint free over backing of 10 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces complete all as specified and as directed by the Engineer-in-charge.

M & L for Plain Cement concrete 25mm thick type B-1, 1:2:4 (using 20mm graded stone aggregate) as in sub base

M&L for PCC (1:2:4) Type B1, (using 20mm graded stone aggregates) as in coping.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required washers and similar small articles conforming to Fe-290 Gde-E-165

S & F 35mm thick flush shutters , solid core construction, with block board core and plywood face panels with both face is covered with deco rative face veneer with lipping/frame to match

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

S & F 75 mm Butt hinges, Medium weight, stainless steel.

S & F 100 mm Butt hinges, Medium weight, stainless steel.

S & F 125 mm Butt hinges, Medium weight, cold rolled mild steel.

S & F 100 mm stainless steel Handles .

S & F 125 mm stainless steel Handles .

S & F 200mm Aluminium anodised,barrel tower bolts of extruded section .

S & F Aluminium handles, cast type,anodised of size 125 mm

S & F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy

S & F 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete

S & F in repairs stainless steel pipe 25mm dia as in Curtain rod for Windows,doors opening etc complete all as specified and directed.

S & F Fancy type chromium plated knobs for fixing curtain rod complete all as specified and directed.

M & L for Anodised Powder coated(any tint) aluminium frame for doors,windows, ventilators,partitions with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thickness of powder coating 50 micron)

S&F anodised powder coated aluminium window shutters, Sliding type without sash bars, including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, Rollers, screws, anodised aluminium fittings such as suitable handle (1 No.) complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S & F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

S & F in repairs Powder coated Aluminium grill/Deco grill for Windows , Ventilators etc

S & F in repairs 15mm internal dia 3-layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S & F in repairs 20mm internal dia 3-layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S & F 25mm internal dia 3-layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylen random fittings fixed complete to walls, ceilings or in floors etc.

S & F in repairs Wash basins of size 550 x 400 over the counter type,Vitreous China including cutting for and pinning in ends of brackets/ or erecting stand/bolts including waste coupling. complete all as specified and as directed by the Engineer-in-charge.

S & F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, low level flushing cistern of 10 Liters capacity and Seat Cover)

S&F in repairs 25mm Globe or gate valve (PPR with steel ball) with iron wheel head,screwed both ends for iron pipe complete all as specified and as directed by the Engineer-in-charge.

Demolition and breaking up drain pipes of dia 100/75mm

S & F PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by the Engineer-in-charge.

S & F PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls

S & F 40/50mm dia PVC pipes for WHB/Sink waste pipes fixed to walls including fiitings and connecting to multiple floor trap.

S & F 4.00mm thick plain Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

S & F PVC (SWR) vent cowl 110mm complete all as specified and as directed by the Engineer-in-charge.

S & F 110mm dia PVC (SWR) bends any radius provided with accesss door complete all as specified and as directed by Engineer In Charge.

S & F 75mm PVC (SWR) multiple floor trap with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-charge.

S & F 75mm dia PVC (SWR) bends any radius provided with accesss door complete all as specified and as directed by Engineer In Charge.

S & F in repairs PVC (SWR) gully trap 110 mm, setting and jointing with solvent cement complete all as specified and as directed by the Engineer-in-charge.

S & F 110mm dia PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed by Engineer In Charge.

S&F in repairs 18/19mm thick plywood grade BWR type BB, fixed with screws to timber frame work.

M&L for Decorative laminate type I of surface finish ,colour and pattern as approved, 0.90mm thick.

S & F Solid PVC Door Frame of size 100mm x 60mm made out of 5mm WOOD GRAIN printed PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with printed sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

M&L for Vitrified parking/path tiles of 10mm thick,size 400x400mm / 300x300mm,set,jointed and pointed in neat cement slurry with grey cement 0and pigment as in floors over a screed bed of 15mm thick in CM(1:4)

S & F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet & 5mm thick x 15mm wide PVC sheed beading used insied Stiles and Rails and decorative PVC beading of 10mm x 10mm (90*) used instead of exposed portion of PVC sheet beading and the paneeling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S & F 150mm Aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-charge.

S & F Figured glass 4mm thick, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

S & F grating doom 125 mm dia with waste hole of PTMT (Min weight 40 gms)

S & F in repairs,15mm bore dia Pillar taps Fancy type,chromium plated, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F PVC flexible connections 15mm size with PTMT nuts of length 600mm

S & F in repairs Brass chromium plated shower rose 125mm size

S & F in repairs Stainless Steel tubular towel rail , 20mm dia, 60cm long between flanges

S & F in repairs Towel ring Round with round flange

S & F Toilet paper holder of Brass CP fixed to walls with chromium plated (CP) brass screws

S & F Soap dish chromium plated, fixed to plugs with chromium plated brass screws

S & F in repairs 15mm bore dia angle valves fancy type Chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S & F in repairs two way bib cock, CP, Fancy type of 15mm dia (Make : Jaguar Catalogue No : FON-40041 or its equivalent as approved by GE)

S & F in repairs Health Faucet for 15mm dia with 1.5m long easy flexible tube in Chrome finish and wall look

S & F in repairs 25mm internal dia PP-R Ball valves (brass insert) as per requirement of the site

Dismantling water tanks of capacity exc 500 but not exc 1000 Ltrs and removing to store

S & F 1000 litres Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed

S & F in repairs Brass CP mixer 15mm for mixing hot & cold water screwed down for iron pipe and fixed

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over wall care putty of 2mm thick over one coat of primer on walls complete all as specified and as directed by the Engineer-in-Charge.

M & L for complete removal of existing treatment on internal walls and applying two coats of Plastic Emulsion paint over wall care putty of 2mm thick over a coat of primer all as specified and directed

M & L for preparation of old painted surfaces of external walls and applying one coat of exterior Emulsion paint all as specified and directed

M & L for preparation of new wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel Paint over a coat of pink primer

M & L for preparation of old wooden Surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying one coat of Synthetic Enamel Paint

M & L for preparation of old ceiling surfaces and applying one coat of white wash all as specified and directed

Forming mortice holes exc 50cucm but not exc 100 cucm for balusters,newels,posts etc and grouting with cement mortar (1:2) after fixing.

M & L for Prelaminated particle board 18/19mm thick ,prelaminated both side with decorative choice lamination fixed with screws to aluminum frame work.

M & L for sheet glass 5.5 mm thick ,ordinary quality and glazing in aluminium frames ,in square exc 0.50 sqm in each pane, complete all as specified and as directed.

M&L for Door closer hydraulically regulated ,designation No:3,universal type,aluminium extruded section body,suitable for door shutters of 851 to 1000mm in width, complete all as specified and as directed.

M&L for washing ,rubbing down and stopping of distempered surfaces and applying two coats of distemper oil emulsion over one coat of primer etc complete all as specified.

M&L for Preparation of old steel Surfaces of any description, over 10cm in width or girth,not otherwise described, and aplying two coats of synthetic enamel paint.

M & L for complete removal and applying three coats of white wash on Ceiling

M&L for Roughening surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc.

M&L for Brushing neat cement slurry with 3.00kg of cement per Sqm

Removing excavated earth n.exc 50M and depositing where directed at a level not exc 1.50M above the starting point.

M & L for 75 mm thick Plain Cement concrete of type D2, 1:4:8 (using 40 mm graded stone aggregate) in sub base to flooring

M & L for Brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 complete all as specified and as directed.

M & L for Precast RCC (1:2:4) Type B1 as in shelves and similar articles ,set in CM(1:4) complete all as specified and as directed.

M & L for Mild steel TMT 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips

M&L for Granite 15 to 20mm thick,of any type (table rubbed and polished) in cooking platforms and the like,in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M & L for Non skid/matt finish ceramic tiles 7 to 8 mm thick of size exc 0.18sqm but not exc 0.38sqm, as in floors etc.set and jointed in neat slurry and pointed in white or coloured cement to match for joint free over screed bed or bedding layer of mortar 15mm thick in CM 1:4

M&L for Granite 15 to 20mm thick,of any type (table rubbed and polished)as in wall linings 12mm thick in CM(1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Dismantling plain or corrugated steel sheeting ,any gauge, thickness as in roof covering

Dismantling mild steel work of any description

Demolition of wall boards(fibre,pulp,insulation etc)any thickness including cover fillets and frame work

Demolition of brickwork built in cement mortar

Demolition of concrete in ground floors and pavings not exc 15cm thickness(below or above ground floor)

Demolition of chajjas ,shelves and similar suspended work of reinforced cement concrete.

Cutting opening through brick wall built in cement mortar for doors,window and other openings,or enlarging existing openings ,converting window into door opening,or cutting out defective brick work for underpinning,including providing,fixing and removing shoring,cleaning of bricks,removing surplus serviceable bricks,hardcore etc to store and rubbish not exc 50 mtrs

M&L for Forming jambs etc to openings in CM(1:4) including cutting,toothing,and properly bonding into old work ,also facing jointing and pointing to match existing work complete.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. Or for shafts, wells, cesspits, manholes, pier holes, etc. N exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil

M&L for plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius with built in CM 1:6

M&L for Reinforced Cement Concrete 1:1.5:3 Type A1 (Using 20mm graded granite stone aggregate) as in lintel , upto 1.50M clear span,including use and waste of form work etc complete all as specified.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item No 108 above but 5mm to 10mm dia as in stirrups,spacers and binders

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated soil exc. 250 m but n exc. 500 m and depositing where directed at a level n exc. 1.5 m above the starting point.

M & L for 100mm thick Boulder Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface

M & L for 75 mm thick Plain Cement concrete of type D2, 1:3:6 (using 40 mm graded stone aggregate) as in subbase

M&L for Anodised powder coated aluminium door shutters ,aluminium section weighing 0.55kg/m,including necessary joining cleats ,glazing clips,rubber neoprene packing,handles 02 Nos in each door,hinges,anodised aluminium snap beading ,screws etc complete all as specified.

S&F Frameless toughened glass door with sliding shutters(02 Nos) shutter 12mm thick ,factory toughened plain sheet glass , not exc 2.00 Sqm,using the stainless steel fittings of polished chrome finish ,in each shutter (satin stainless steel finish for handles) including cutting necessary holes and cutouts complete all as specified and as directed by Engr-in-charge.

S&F Sheet glass 4.8mm thick, ordinary quality and glazing with neoprene gasket in squares exc 0.50Sqm in each pane.

S&F Steel rolling shutter lath thickness 1.00mm,without ball bearing ,as specified including top cover ,anchoring rod,hasp and staple and one shop coat of primer ,errected in position as indicated ,complete ,gear operated with bevel gear box and crank handle.

M&L for Mild steel angles as in frame work for aluminium composite panel (ACP) cladding, including cutting tops to shape as required,necessary drilling,bolting or rivetting etc and similar work conforming to Fe 290 Grade E-165

M&L for Anodised aluminium frame work for aluminium composite panel (ACP) sheet cladding including joining cleats for fixing etc complete all as specified

Design,supply and fix at site of the tray panel screw type system with aluminium composite panel of approved colour on exterior walls, ACP soffits,copings,slab projections at all heights and elevation . The aluminium composite panel shall be 4mm thick consisting of 3mm thick thermoplastic core of antioxidant LDPE sandwitched between 2 skins of 0.5mm thick aluminium alloy sheet making a total panel thickness of 4mm . The external surface shall be finished with PVDF paint , all as specified and as directed by Engr-in-charge. ( Make: ALUCOBOND/ ALSTRONG/ EUROBOND or its equivalent as approved by GE)

Fabrication,errection and fixing only MS Pipes fixed independantly without connecting plates etc.(using retrieved material from item No.95 above)

Fabrication,errection and fixing only steel work in tubular trusses including special shaped washer etc complete using induction butt welded tubes conforming to IS 1161-1998 grade St 240 .(using retrieved material from item No.95 above)

Fabrication,errection and fixing only steel work in tubular trusses including special shaped washer etc complete using induction butt welded tubes conforming to IS 4923-1997 SHS.(using retrieved material from item No.95 above)

Fixing only prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick as in roof covering fixed with self tapping screws all as specified (using retrieved roofing sheets from item No.94 above)

M & L for Non skid/matt finish ceramic tiles 7 to 8 mm thick of size 600x 600 mm as in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match for joint free over screed bed or bedding layer of mortar 15mm thick in CM 1:4

M&L for 15 mm thick rendering on brick work or concrete surfaces in cement mortar 1:4 finished even and fair ,using integral water proofing compound without using extra cement complete all as specified and directed [Note: WPC will be measured and paid separately under relevant item]

Supply only integral water proofing compound

M&L for Preparation of new plastered wall surfaces and applying two coats of exterior emulsion paint over priming paint .

M&L for complete removal of existing treatment on wall and applying two coats of plastic emulsion paint over priming paint including applying 3mm thick wall care putty on walls.

M&L for Preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer

M&L for Preparation of old painted surfaces of steel of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint

M&L for complete removal of existing treatment on wall and applying two coats of exterior emulsion paint over priming paint including applying 3mm thick exterior wall care putty on walls.

Taking down carefully existing aluminium conductor point wiring (light / fan / socket or power point) complete, with all fittings such as switches, socket, regulator, ceiling rose, utility light fittings and lamp holders etc and removing materials from site and making good the disturbed surfaces of walls roof and floor etc as per existing specification complete all as specified and as directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and fan regulators etc. for reuse at site complete all as specified and as directed. (Note : To be measured only when found serviceable in all respects complete for reuse)

Material and labour for point wiring for one light controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn carefully through existing/new concealed conduit along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including new pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc including testing on completion complete including making good disturbed surface all as specified and as directed.

All as per Item No 135 above but for one fan point controlled by 1 one way switch and regulator all as specified and as directed.

All as per Item No 135 above but for one 3 pin switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per Item No 135 above but for one switch socket outlet, 5 Amp on same board with other switches all as specified and as directed

All as per Item No 135 above but for one16 Amp 3 & 5 pin switch socket outlet, independent with 4 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 4 sqmm and one single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 2.5 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 to the ends with taking down old unserviceable sub main wiring and making good disturbed surface complete all as specified and as directed. [NOTE: Two runs of 4 Sqmm, one run of 2.5 Sqmm and one run of PVC concealed conduit 25mm dia will be measured as one unit i.e RM]

Supply and fixing socket out let multipurpose 3 pin 15 amp and one 3 pin 5 amp controlled by and including one 15 amp switch all as specified and as directed.

Supply and fixing switch piano flush button single pole one way 5 amps all as specified and as directed

Fixing only switch flush button single pole one way 5 amp (Material obtained from item No 134 here in before) all as specified and as directed.

Supply and fixing switch socket outlet 5 pin 5 amp flush type with including switch all as specified and as directed

Fixing only switch socket outlet 5 amp flush type (Material obtained from item No 134 here in before ) all as specified and as directed.

Supply and fixing ceiling rose surface bakelite three terminals all as specified and as directed.

Fixing only ceiling rose surface bakelite three terminals (Material obtained from item No 134 here in before) all as specified and as directed.

Supply and fixing fan regulator electronic deluxe rotary step type all as specified and as directed.

Fixing only fan regulator any type all as specified and as directed. (Material obtained from item No 134 here in before)

Supply and fixing sheet metal enclosure for MCCB, DBs, phosphatised, Powder coated , Triple Pole and Neutral (TPN), suitable for 4 way, Double door 415 Volts all as specified and as directed .

Supply and fixing in proper position MCCB four pole of capacity 100 amps, 415 Volts 25kA breaking capacity all as specified and as directed.

Supply and fixing MCB Four Pole (FP) C curve 10kA breaking capacity of 63 amps, 415 Volts in proper position all as specified and as directed.

Supply and fixing MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed.

S&F in proper position MCB Double Pole of capacity up to 40 amps, 240 Volts c-series with 10kA breaking capacity all as specified and as directed.

Supply and fixing indoor luminare decorative batten for wall/ceiling mounting box type Extruded aluminium housing ,PC Diffuser,energy efficient saving LED BATTEN LIGHT 20W,230 V,50 HZ, slim integrated design easy install including twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed. [Make:CGCat Part no.CCS-100-20-65-HL2-DP-NWH or its equivalent as approved by GE]

S&F Recess Mounting luminaris LED downlighter of 36 W white in the shape of Square 2' x2' feet complete all as specified and as directed [Make :-CG cat no -CCR-127-36-57-SL-NWH or its equivalent as approved by GE]

Fixing only Recess Mounting luminaris LED downlighter of 36 W white in the shape of Square 2' x2' feet complete all as specified and as directed.(Material obtained from item No 134 here in before )

Supply and fixing on wall security LED light luminaire fitting 1X25 W and including cable for connection from celling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1m long bent to shape including bolt, nut,washer,clamp etc all as specified and as directed by the Engineer-in-charge.

Taking down carefully ceiling fan any sweep and any make after disconnecting the electrical connection, dismantling the blades and removing fan including blades for safe custody for reuse and re-assembling the fan complete and refixing the fan in same position including all electrical connection all as specified and as directed.

Material and labour for painting of ceiling fans complete of any sweep/make with one coat of first quality synthetic enamel paint of approved tint by spray including preparation of old painted surface and removing all dust, oil mark etc and filling cavaties with filler materials,and writing serial / MES number as specified (with paint of black colour with each letters/figures in Block of height n.exc 2 cm ) complete all as specified and as directed.

Supply and fixing Ceiling fan of 1200 mm sweep 5 STAR RATING with clamp and hook at proper position with taking down old ceiling fan and kept in MES Store yard with necessary acceseories etc.all as specified and as directed. [Make Havells model No : ES 40 or its equivalent as approved by GE]

Supply and fixing AC three phase static Electronic KWH energy meter of accuracy class 1.0, 240v, 50 Hz , with baclite LCD Display, of rating 10-60 A with transperent hinged type box with six month history of energy in KWH with taking down old meter and kept in MES Store yard with acccessories all as specified and as directed.

Supply and fixing of single pole and neutral enclosure of 20Amps, 240Volt with a two pin and earth plug and socket complete with one double pole MCB complete all as directed by Engr-in-charge.

M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground and connected to galvanized steel earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in electrical plate No 3 of SSR Pt I including necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick pre cast RCC (1:2:4) type B-1 cover slab including providing charcoal or coke and common salt with funnel and 20 mm bore galvanized iron watering pipe (light grade) wire mesh, lugs, complete in all respect GI earth wire protected by 15 mm bore (Medium grade) galvanized iron pipe and other end connected with main switch board all as specified and as directed

Supply and installed hi wall split AC units indoor / out door complete with cordless remote control unit and with in built air ioniser, working on Dual Rotor Inverter Technology and plasma filter for better indoor air quality with minimum 3 star rating and ISEER 3.2 of capacity 2 ton complete all as specified and directed by the Engr- in - charge

M&L for Voltage stabilizer for automatic operation single phase naturally air cooled indoor type & desigened for input variation between170 Volt to 275 Volts with out put voltage stabilizer to 230 volts with accuracy of +/- 2.5 % and capacity of 5 KVA complete all as specified and directed by the Engr- in - charge

Material and labour for concealed point wiring PVC insulated and unsheathed cable with 6.0 Sqmm FRLS copper conductor single core multi strand 1100 Volt drawn through PVC Conduit of suitable size and concealed metal box including 6.0 Sqmm earth wire copper insulated wire connected to common earth dolly for 6/16 A socket and AC power socket complete all as specified and directed by the Engineer -in- charge

S & F Single pole and neutral sheet metal enclosure with two pin and earth plug and socket 240 volts,50 HZ complete with one single pole MCB 20 Amps Complete all as specified and directed by the Engineer -in- charge

SWATHI CONSTRUCTIONS