Dalabar, Maheshmunda and adjoining villages Rural Water Supply Scheme under D.W. and S. Division Jamtara on turnkey basis.

Amount

WATER TREATMENT PLANT

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and necessary equipment for designing & construction of Unconventional WTP of 1.90 MLD capacity. With all complete job. (Please refer to Section 5,Sl. 2.3 of SBD)

Elevated Service Reservoir

At Kumardaha Village (Zone - 1) Capacity 2.90 Lakh Litres, Staging height - 18 m

At Chital Kanali Village (Zone - 2) Capacity 2.20 Lakh Litres, Staging height - 18 m

Intake Well With Pump House 5.00 M dia

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand construction of R.C.C Intake well with Pump house all complete job. (Please refer to Section 5,Sl. 2.1 of SBD)

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, outlet, intake well etc. as per designed section in all kind of soil including moorum soil, soil mixed with kankar, pebbles & boulders upto 300m size & disposal of the same ( beyond 50 m away from the edge of the trenches) with initial lead of 150 M & initial lift of 1.50M as per specification & direction of E/I.

Initial Lift

1st Lift

2nd Lift

3rd Lift

4th Lift

5th Lift

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, outlet, intake well etc. as per designed section in hard rock where blasting is needed & stacking properly in approved stack size in approved stack yard (beyond 50m from the edge of the trenches in the country side) with initial lead of 150 m & initial lift of 1.50m as per specification & direction of E/I (Excavated hard rock size should not be more than 150 lb.)

5th Lift 5.50 to 6.50 M

6th Lift 6.50 to 6.75 M

Providing P.C.C M-150 with in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 ) including , screening ,shuttering ,mixing cement concrete in mixture and placing in position vibrating striking curing taxes and royality all complete as per building specification and direction of E/I.

Providing and laying in situ cement concrete of trap / granite / quartzite / gneiss metal for RCC work in foundation like raft , grillage , strip foundation and footing of RCC columns and steel stanchions including normal dewatering , plywood from work bully / steel propups compaction , finishing and curing etc. complete . (By weigh batching and mix design for M-25 and M-30 only . (excluding M.S or Tor) For RCC Foundation (Intake Well base slab) Grade M30 (Using Concrete Mixture)

Providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quality for RCC work as per detailed drawing and designs or as directed by Engineer - in- charge including normal dewatering centering plywood form work , bully/steeel prop-ups compaction finishing the formed surfaces with CM 1 : 3 of sufficint minimum thickness if special finish is to be provided and curing etc. complete . (By weigh batching and mix design for M-25 and M-30 only . (excluding M.S or tor reinforcement ) for RCC M-300 grade (Vertical walls)

Providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quality for RCC work as per detailed drawing and designs or as directed by Engineer - in- charge including normal dewatering centering plywood form work bully /steel prop-ups , compection finishing the formed surface with CM1:3 of sufficient minimum thickness if special finish is to be provided and curing etc. complete ((By weigh batching and mix design for M-25 and M-30 only . (excluding M.S or tor reinforcement ) for RCC M25 grade Beam

Providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quality for RCC work as per detailed drawing and designs or as directed by Engineer - in- charge including normal dewatering centering plywood form work bully /steel prop-ups , compection finishing the formed surface with CM1:3 of sufficient minimum thickness if special finish is to be provided and curing etc. complete ((By weigh batching and mix design for M-25 and M-30 only . (excluding M.S or tor reinforcement )

Providing RCC M 250 with nominal mix in columns with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of FM, 2.5 to 3 including shuttering, mixing cement concrete in mixer and placing in position, vibration, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete job as per specification and direction of E/I.

Providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quality for RCC work as per detailed drawing and designs or as directed by Engineer - in- charge including normal dewatering centering plywood form work bully /steel prop-ups , compection finishing the formed surface with CM1:3 of sufficient minimum thickness if special finish is to be provided and curing etc. complete ((By weigh batching and mix design for M-25 and M-30 only . (excluding M.S or tor reinforcement ) for RCC M25 grade Beam

Providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quality for RCC work as per detailed drawing and designs or as directed by Engineer - in- charge including normal dewatering centering plywood form work bully /steel prop-ups , compection finishing the formed surface with CM1:3 of sufficient minimum thickness if special finish is to be provided and curing etc. complete ((By weigh batching and mix design for M-25 and M-30 only . (excluding M.S or tor reinforcement )

Providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quality for RCC work as per detailed drawing and designs or as directed by Engineer - in- charge including normal dewatering centering plywood form work bully /steel prop-ups , compection finishing the formed surface with CM1:3 of sufficient minimum thickness if special finish is to be provided and curing etc. complete ((By weigh batching and mix design for M-25 and M-30 only . (excluding M.S or tor reinforcement ) for RCC M25 grade Beam

Providing suttering

Providing TMT reinforcement (TOR steel) 12 mm as per approved design drawing , removal of rust cutting , bending, binding including supplying annealed wire placing MS rods in position all complete job as per specification and direction of E/I. (1% of Total RCC Quantity)

Providing designation 75A brick work in CM 1:6 in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, costs of screening, materials, scaffolding, racking out joints to 15 mm depth curing, taxes and royalty all complete as per building specification & direction of E/I.

Supplying fitting and fixing full glazed steel Supplying fitting and fixing fully glazed steel door window or ventilators standard rolled Z and mullion section and sizes as per I.S.-1038 joints met and welded with 100 x 16 x 3 mm MS lugs fixed in cement concrete (1:2:4) blocks 15 x 10 x 10 cm size including cost of oxidized iron fitting with hinges, handle per steps, catch springs 3mmv thick plain glass panes with Aluminium beads and inner frame fixed with lugs of 20 mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint, carriage to work site hoisting and placing in position in all storey and taxes all complete as per building specification and direction of E/I.

Supplying,fitting & fixing M.S grill gate with M.S. grills made of 20 X 6 mm M.S flats or 16 mm. M.S. square bars fitted on 25 X 25 X 6 mm. (When steel is not supplied by the department)

Supplying & fixing rolling shutters of approved make, made of required sixe M.S.laths interlocking together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside & outside locking with push & pull operation complete includeing cost of providing & fixing necessary 27.5 cm long wire springs grade No.2 & M.S. top cover of required thickness for rolling shutter.

Providing and fixing ball bearing for rolling shutter.

Providing 12 mm thick cement plaster (1:4) for inside & cut safe surface of p/H with clean coarse sand of P M 15 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6 mm thick cement plaster (1:4) in ceiling of P/H & Intake well with clean coarse BCD 5.7.6 sand of FM 1.5 including screening, curing with all leads and lift of water , scaffolding taxes and royalty all complete as per building specification and direction of E/I

Providing 19 mm water proof cement plaster (1:3) with clean coarse sand of FM 1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I.

Provide two coat of snowcem of approved shade & make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding, curing & taxes all complete as per building specification & direction of E/I.

Provide two coat of snowcem of approved shade & make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding, curing & taxes all complete as per building specification & direction of E/I.

Providing structural steel work in single stanchion composed of Rolled Steel Joist , channel etc. with caps, bases, mild steel plates, angles, brackets, cleats, gusset plates, anchor bplts etc. as per detailed design amd drawing or as directed by Engineer-in-charge.

ISMB 600 X 210 mm

ISMB 200 X 100 mm

ANGLE 100 X 110 X 12 mm

Labour for fabricating, erecting, hoisting & fixing in position structural steel work in RS joist, channel, angle, tee, flat, plate, latice member, built up compound section in column, girder, staircase, of truss including cost of gusset plates, holding down bolts, anchor plates at all height & depths, bolting welding ( machining wherever necessary) with applying a priming coat of red lead paint all complete as per approved drawing building specification and direction of E/I.

Providing and fixing GI pipe railing having 1.0 M height consisting 50x50x6 mm thick MS angles as verticals at 1.5 m c/c and additional posts at every corner with 3 rows of 25 mm dia GI pipes of medium class veriety as horizontal and painting 3 coats of oil paint over one coat of anticorrosive paint at approved colour and shade including cost of all labour, transporting bends to curved shape etc. complete

Providing and fixing MS sluice gates in position as per dtailed drawing and specification including cost of all materials, labour, operating pedestal, connecting rod, painting with three coats of anti-corrosive paint, etc. complete as directed by Engineer-in-charge.

Providing and fixing in position C.I. /M.S. rose pieces in intake wells including cost of all materials and labour, painting with three coats of anti-corrosive oil paint, etc.complete as directed by Engineer-in-charge.

Providing and Fixing in Position of 20 mm dia M.S. bar Step with proper anchorage, etc. and providing and applying 3coats of ant- corrosive paint , etc. complete as directed by Engineer in charge.

Providing C.I cover with frame for man hole of size 600 mm X 450 mm (wt.39 kg)

Supplying equipment and labour for back filling the excavated earth around steining well all complete as per specification and direction of E/I.

Carriage of material from divisional store are kiln side or quality side to work including contractor profit loading ,unloading transportation are complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Bricks 6 KM lead

Stone/Stone Chips 11 KM lead

Gangway 50 M long and 3.0M wide

Earthwork in excavation of foundation trenches of toe wall, spillway , head regulator, outlet , intake well etc. as per designed section in all kind of soil including moorum soil , soil mixed with kankar, pebbles and boulders upto 300 mm size and disposal of the same (beyond 50m away from the edge of the trenches) with initial lead of 150m and initial lift of 1.5m as per specification and direction of E/I.

Initial Lift

1st Lift

2nd Lift

3rd Lift

4th Lift

5th Lift

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, outlet, intake well etc. as per designed section in hard rock where blasting is needed & stacking properly in approved stack size in approved stack yard (beyond 50m from the edge of the trenches in the country side) with initial lead of 150 m & initial lift of 1.50m as per specification & direction of E/I (Excavated hard rock size should not be more than 150 lb.)

5th Lift

6th Lift

Providing P.C.C.M-150 in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating,striking,curing taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying in situ Cement concrete of trap/ granite/ quartzite / gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, plywood form work, bully/steel propups, compaction, finishing and curing, etc, complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S. or Tor In RCC M-250).

Providing and laying in situ Cement concrete of trap/ granite/ quartzite/ gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, plywood form work, bully/steel propups, compaction, finishing and curing, etc, complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S. or Tor In RCC M-250).

Providing and casting in situ Cement concrete of trap/granite/quartzite/ gneiss metal for RCC work as per detailed drawing and designs or as directed by Engineer in Charge including normal dewatering, plywood form work, bully/steel propups, compaction, finishing and curing, etc, complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S. or Tor In RCC M-250) For Bracings

Providing R.C.C. M-200 with nominal mix of (1:1.5:3) in beam of all types with approved quality of stone chips 20 mm to 6 mm. size graded and clean coarse sand of F.M. 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement), taxes and royalty all complete, as per building specification and direction of E/I.

Providing R.C.C.M- 200 with nominal mix of (1:1.5:3) in roof slab with approved quality of stone ships 20 mm to 6 mm. size graded and clean coarse sand of F.M. 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement), taxes and royalty all complete, as per building specification and direction of E/I.

Providing tor steel reinforcement of 10 mm, 12 mm & 16 mm. dia dia bar as per approved design and drawing excluding carriage of bar to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per Specification and direction of E/I. (TMT Fe-500 only valid for SAIL & TATA Steel)

Providing 12 mm thick cement plaster (1:4) with approved quality of sand of requisite F.M. (2.5 to 3.0) washed and screened including curing, scaffolding wherever required and its removal royalty and all taxes etc. complete as per Specification and direction of E/I.

Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification & direction of E/I.

Providing & Fixing G.I.Pipe Railing having 1.0 m height consisting 50x50x6 mm thick M.S.Angles as verticals at 1.5 m c/c and additional poles at every corner with three rows of 25 mm dia G.I.pipes of medium class variety as horizontal & painting three coats of oil paint over 1 coat of anticorrosive paint of approved colour & shade including cost of all labour, transporting bends to urved shape etc. complete.

Providing two coat of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, Scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit, loading, unloading, transportation, etc. all complete.

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Mechanical & Electrical Work at Intake well

Supply, installation, testing and commisssioning of vertical turbine pumpsets with allied equipment as under (Please refer to Section 5,Sl. 2.4 of SBD)

Vertical Turbine Pump (As pe IS 1710) [make: Kirloskar/Jyoti/ Worthington/ Mather & Platt], capable of discharging - 74088 LPH, 75 M. mounted on common base plate and coupled with TEFC & IE 3, squirrel cage induction motor, rating of motor 15% more BHP than that of pump, operating on 1500 rpm, 415V, 50Hz [make:Kirloskar/ABB/ Jyoti/Crompton Greaves/BHEL] pressure gauge, required size of sluice valve and non-return valve, standard fittings etc. including construction of MS Common Header and delivery header, jointing it with Suction and Delivery line by providing required MS/CI pipes, flanges,reducer and specials, nuts bolts, packings etc. all complete as per the requirement, standards and instruction of E/I.(Contrator will again have to check the design of motor,pump & he will to get it approved by the Deptt.)

Discharge - 21.77 LPS and Head - 86 m (1W+1S)

Cable: Power wiring with required 120 Sq mm, 3.5 core, 1.1KV grade, armoured cable, Standard Aluminium conductor, XLPE/PVC insulated cable from Transformer to Stablizer & Panel (MCP) including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Cable: Power wiring with 3 core, 1.1KV grade, Unarmoured cable, Standard Copper conductor, XLPE/PVC insulated cable from Panel (MCP) to Motors & Staters including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Earthing: Earthing with copper earth plate including accessories and providing masanory enclosure with cover plate having locking arrangement and watering pipe of 2.7 m long etc. with charcoal / coke and salt as required conforming IS:3043.

Starter: Supplying, installation, testing & commissioning of assembled Fully Automatic Star Delta starter, in a provided cubical panel to operate induction motor with no volt coil, over load relay and ON/OFF push buttons, with necessary material and connected to supply, etc. all complete.

1) 50 HP Motor

Crane: Providing, erecting triple spur gear type Chain Pulley Block suitable for 3 Tonne capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. With travelling trolly

1) 100 KVA Oil Cooled

Tansformer Installation: Cost of construction of DP structure with different type of MS channels, M.S. angles, brackets, insulators, AB Switch, three set of horn gap fuse, DO fuse and lightening arrester, nut bolts, fabrication work required for the job, cost of earthing of transformer (Two nos., one no. for neutral and one for body) with all required material labours, cost of providing disc & pin insulator for HV and LV side of the transformer, testing of dielectric strength of transformer oil etc. for transmission of power. All complete job as per I.E. rules and specification of Jharkhand state electricity board. (100 KVA (11/.433 KV) Including DP Structure)

Lighting: Providing internal and external lighting by doing wiring and installing lumenaries e.g. suitable Wattage of LED light fittings in pump house, gangway, etc. all complete as per requirement at Pump house area.

Safety Items: Supplying, Installation and erecting of Fire extinguisher, Lightening Arrestor, emergency light, First aid box, insulation gloves & shoes, tools & tackles, rubber matting, instruction manual, etc. as per requirement and Indian standards at Pump house.

(Mechanical & Electrical Part at WTP)

Suply, installation, testing and commisssioning of horizontal casing centrifugal pumpsets with alied equipment as (Please refer to Section 5,Sl. 2.5 of SBD)

Horizontal Split Casing / Multistage Centrifugal Pump as per IS 5120 [make: Kirloskar/Jyoti/ Worthington/ Mather & Platt], capable of discharging required amount of water. mounted on common base plate and coupled with TEFC & IE 3, Eff1, squirrel cage induction motor, rating of motor 20% more BHP than that of pump, operating on 1500 rpm, 415V, 50Hz [make:Kirloskar/ABB/ Jyoti/Crompton Greaves/BHEL] pressure gauge, required size of sluice valve and non-return valve, standard fittings etc. including construction of MS Suction and delivery header, jointing it with Suction and Delivery line by providing required MS/CI pipes, flanges,reducer and specials, nuts bolts, packings etc. all complete as per the requirement, standards and instruction of E/I.(Contrator will again have to check the design of motor,pump & he will to get it approved by the Deptt.)

Discharge - 21.77 LPS and Head - 46 m (1W+1S)

Cable: Power wiring with required 120 Sq mm, 3.5 core, 1.1KV grade, armoured cable, Standard Aluminium conductor, XLPE/PVC insulated cable from Transformer to Stablizer & Panel (MCP) including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Cable: Power wiring with 3 core, 1.1KV grade, Unarmoured cable, Standard Copper conductor, XLPE/PVC insulated cable from Panel (MCP) to Motors & Staters including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Earthing: Earthing with copper earth plate including accessories and providing masanory enclosure with cover plate having locking arrangement and watering pipe of 2.7 m long etc. with charcoal / coke and salt as required conforming IS:3043.

Starter: Supplying, installation, testing & commissioning of assembled Fully Automatic Star Delta starter, in a provided cubical panel to operate induction motor with no volt coil, over load relay and ON/OFF push buttons, with necessary material and connected to supply, etc. all complete.

1) 25 HP Motor

Crane: Providing, erecting triple spur gear type Chain Pulley Block suitable for 3 Tonne capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. With travelling trolly

1) 60 KVA Oil Cooled

Tansformer Installation: Cost of construction of DP structure with different type of MS channels, M.S. angles, brackets, insulators, AB Switch, three set of horn gap fuse, DO fuse and lightening arrester, nut bolts, fabrication work required for the job, cost of earthing of transformer (Two nos., one no. for neutral and one for body) with all required material labours, cost of providing disc & pin insulator for HV and LV side of the transformer, testing of dielectric strength of transformer oil etc. for transmission of power. All complete job as per I.E. rules and specification of Jharkhand state electricity board. 100 KVA transformer with DP structure

Safety Items: Supplying, Installation and erecting of Fire extinguisher, Lightening Arrestor, emergency light, First aid box, insulation gloves & shoes, tools & tackles, rubber matting, instruction manual, etc. as per requirement and Indian standards at Pump house.

Raw Water Rising main.

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Raw & clear water Rising Main (Please refer to Section 5,Sl. 3.0 of SBD)

Earthwork in excavation (as per I.S. 3114/1965 for laying of different type and sizes of pipe so as to give one meter avarage cover over the socket of pipes with disposal of excavated with in initial lead and lift as per specification and direction of engineer-in charge.

Earthwork in excavation in ordinary rock or soft rock (Where blasting is not needed) (vide type of soil item -C) with initial lead of 10M, and lift of 1.5M. including dressing making the sides in proper profile profile and dressing the bed in proper grade etc. all complete as per specification & direction of E/I . Initial lead 10 m & lift 1.50 m.

Providing and supplying ISI mark centrifugally cast (spun) ductile Iron pipes of 100 mm and above all diameter for water works with sockets and spigot ends confirming to IS 8329/2000 in standared working lengths of 4.5, 5.5 and 6.0 M for classification K-7 and K-9 suitable for push on joints (rubber gasket D jointing) with cement mortar lining inside the pipes with outsides zinc and bituminious coating rate are ex-factory including transportation, taxes and duties contractor profit and over head charges etc. 10% Contracters profit added and Rates Are For Jharkhand .

1) 200 mm Dia. DI K-9

Providing and supplying D.I. specials and fitting with sealing rubber gasket of SBR complete with cast iron follower gland and M.S nutbolt coated or otherwise protected from rusting and suitable for DI pipes includingcost of labour, materials, and transportation to stores/ site, loading and unloading including all taxes etc. complete as per IS-9523. Cost of specials = 2% of pipeline cost

100 - 300 mm Dia.

Supplying labours, tools and tackles, lubricant etc. for laying and jointing C.I.S/S tyton pipes (class LA) trenches supplying rubber gasket (Rubber gasket confirming to I.S.S.-5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete (Pipe to be supplied departmentally free of cost and laying of pipes is to be done as per I.S.S. 3114-1985) as per design, specification and direction of E/I.

1) 200 mm Dia. DI K-9

Supplying labours, tools and tackles for testing of laid CI pressure pipe upto 60 m head of water all complete as per specification and direction of E/I. (Water to be supplied free of cost departmently)

1) 200 mm Dia. DI K-9

Labour charge for one cutting of C.I/ D.I and specials including suppying supplying, necessary tools and plants ,chipping or filling the surface finish as per specification and direction of E/I.

1) 200 mm Dia. DI K-9

Supplying double flanged sluice valve confirming for IS 2906/14846 including warn gear arrengements as per test pressure stainless steel splindle /caps etc. complete (Sluice and scour valve) PN1.6 without by pass arrengement

200 mm Dia

Supplying labour and tools for fixing C.I. sluice valve in trenches with pair of C.I. Tail piece including making laed caulked joints and flanged joint as per I.S.S. specification including supplying all jointing material (pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S. 6587-1972 and nuts and bolt confirming to I.S.S. 1364-1983) including drilling holes in flanges if required as per specification and direction of E/I.

200 mm Dia (Sluice valve+NR valve)

Providing and supplying ISI mark CI D/F reflux valves (non-return valves) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete.Reflux valves as per I.S.5312 Part I (1984)

200 mm Dia

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete. Kinetic Air valve flanged type. PN-1.6

1) 25 mm dia.

Lowering & laying and fixing in proper alignment and position all types of CI air valve as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing etc. complete. (for all class of valves)

1) 25 mm dia.

Providing and constructing B.B. masonary valve chamber with 15mm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B masonery in CM 1:5 proportion precast RCC frame & cover, etc. complete as per directed by Engineer-in-charge.Wall thickness : 0.23 M for depth of 1.20M and 0.35 M for balance depth exceeding 1.20 M

ii) 1.20 x 0.9 m, depth 1.50M with cover.

Providing P.C.C. M-150 with nominal mix of (1:3:6) in foundation with approved quality stone metal (20 mm to 6 mm Size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of Engineer -in charge

A) Thrust block

For 1) 200 mm Dia. DI K-9 Pipe

Earthwork in backfilling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-charge.

Clear Water Rising main.

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Raw & clear water Rising Main (Please refer to Section 5,Sl. 3.0 of SBD)

Earthwork in excavation (as per I.S. 3114/1965 for laying of different type and sizes of pipe so as to give one meter avarage cover over the socket of pipes with disposal of excavated with in initial lead and lift as per specification and direction of engineer-in charge.

Earthwork in excavation in ordinary rock or soft rock (Where blasting is not needed) (vide type of soil item -C) with initial lead of 10M, and lift of 1.5M. including dressing making the sides in proper profile profile and dressing the bed in proper grade etc. all complete as per specification & direction of E/I . (initial lead 10 m & lift 1.50 m)

Providing and supplying ISI mark centrifugally cast (spun) ductile Iron pipes of 100 mm and above all diameter for water works with sockets and spigot ends confirming to IS 8329/2000 in standared working lengths of 4.5, 5.5 and 6.0 M for classification K-7 and K-9 suitable for push on joints (rubber gasket D jointing) with cement mortar lining inside the pipes with outsides zinc and bituminious coating .The rates are F.D.R Jharkhand

1) 150 mm Dia. DI K-9

2) 200 mm Dia. DI K-9

Providing and supplying D.I. specials and fitting with sealing rubber gasket of SBR complete with cast iron follower gland and M.S nutbolt coated or otherwise protected from rusting and suitable for DI pipes includingcost of labour, materials, and transportation to stores/ site, loading and unloading including all taxes etc. complete as per IS-9523.

100 - 300 mm Dia.

Supplying labours, tools and tackles, lubricant etc. for laying and jointing C.I.S/S tyton pipes (class LA) trenches supplying rubber gasket (Rubber gasket confirming to I.S.S.-5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete (Pipe to be supplied departmentally free of cost and laying of pipes is to be done as per I.S.S. 3114-1985) as per design, specification and direction of E/I.

1) 150 mm Dia. DI K-9

2) 200 mm Dia. DI K-9

Supplying labours, tools and tackles for testing of laid CI pressure pipe upto 60 m head of water all complete as per specification and direction of E/I. (Water to be supplied free of cost departmently)

1) 150 mm Dia. DI K-9

2) 200 mm Dia. DI K-9

Labour charge for one cutting of C.I/ D.I and specials including suppying supplying, necessary tools and plants ,chipping or filling the surface finish as per specification and direction of E/I.

1) 150 mm Dia. DI K-9

2) 200 mm Dia. DI K-9

Supplying double flanged sluice valve confirming for IS 2906/14846 including warn gear arrengements as per test pressure stainless steel splindle /caps etc. complete (Sluice and scour valve) PN1.6 without by pass arrengement

150 mm Dia

200 mm Dia

Supplying labour and tools for fixing C.I. sluice valve in trenches with pair of C.I. Tail piece including making laed caulked joints and flanged joint as per I.S.S. specification including supplying all jointing material (pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S. 6587-1972 and nuts and bolt confirming to I.S.S. 1364-1983) including drilling holes in flanges if required as per specification and direction of E/I.

150 mm Dia

200 mm Dia

Providing and supplying ISI mark CI D/F reflux valves (non-return valves) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete.Reflux valves as per I.S.5312 Part I (1984) PN 1.6

150 mm Dia

200 mm Dia

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete. Kinetic Air valve flanged type. PN-1.6

1) 25 mm dia.

Lowering & laying and fixing in proper alignment and position all types of CI air valve as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing etc. complete. (for all class of valves)

1) 50 mm dia.

Bulk Meter - Providing, installing and giving satisfactory field testing of bulk water meter, horizontal inferential multijet type with magnetic drive and dry dial suitable for ambient 50º C Temperature duly sealed against tampering complete with flanges at both ends and conforming to class B as per ISO 4064 along with manufacturer's test certificate and guarantee certificate, including cost of all materials and labour etc with OIML. MID certification for Abroad meter and FCRI for India including 36 months guarantee etc complete.

a) Removable mechanism type Bulk water meter as per ISO 4064

200 mm dia.

150 mm dia.

Providing and constructing B.B. masonary valve chamber with 15mm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B masonery in CM 1:5 proportion precast RCC frame & cover, etc. complete as per directed by Engineer-in-charge.Wall thickness : 0.23 M for depth of 1.20M and 0.35 M for balance depth exceeding 1.20 M

ii) 1.20 x 0.9 m, depth 1.50M with cover.

Providing P.C.C. M-150 with nominal mix of (1:3:6) in foundation with approved quality stone metal (20 mm to 6 mm Size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of Engineer -in charge

A) Thrust block

For 1) 150 mm Dia. DI K-9 Pipe

For 2) 200 mm Dia. DI K-9 Pipe

Earthwork in backfilling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-charge ( Refilling )

DISTRIBUTION MAIN

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labour, materials, equipment to procure and laying of DI class K-7 pipes with Cement Mortar Lining for distribution main (Please refer to Section 5,Sl. 3.0 of SBD)

Earthwork in excavation (as per I.S. 3114/1965 for laying of different type and sizes of pipe so as to give one meter average cover over the socket of pipes with disposal of excavated with in initial lead and lift as per specification and direction of engineer-in charge.

Earthwork in excavation in ordinary rock or soft rock (Where blasting is not needed) (vide type of soil item -C) with initial lead of 10M, and lift of 1.5M. including dressing making the sides in proper profile profile and dressing the bed in proper grade etc. all complete as per specification & direction of E/I .

Supplying labours , tools tackles ,lubricant etc for laying and jointing DI / C.I.S/S tyton pipes (class LA)in trenches without supplying rubbber gasket and making gasket joints including providing night guard , barrier and red light to safe guard against accident all complete ( Pipe to be supplied depatmentally free of cost and laying of pipes is to be done as per (I.S.S 3114-1985) as per design , specification and direction of E/I.

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

Supplying labours, tools and tackles for testing of laid CI or U.P.V.C. OR H.D.P.E. OR A.C. pressure pipe upto 60m head of water all complete as per specification and direction of E/I.

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

Labour charge for one cutting of C.I/ D.I and specials including suppying supplying, necessary tools and plants ,chipping or filling the surface finish as per specification and direction of E/I.

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

Supplying labour and tools for fixing C.I. sluice valve in trenches with pair of C.I. Tail piece including making laed caulked joints and flanged joint as per I.S.S. specification including supplying all jointing material (pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S. 6587-1972 and nuts and bolt confirming to I.S.S. 1364-1983) including drilling holes in flanges if required as per specification and direction of E/I.

100 mm dia

150 mm dia

200 mm dia

Providing and constructing B.B. masonary valve chamber with 15cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B masonery in CM 1:6 proportion precast RCC frame & cover, etc. complete as per directed by Engineer-in-charge.Wall thickness : 0.25 M for depth of 1.20M and 0.35 M for balance depth exceeding 1.20 M

i) 1.20 X 0.90m, depth 1.5M with cover.

Cutting the road as well as restoring the same as per specifications and as directed by Engineer incharge

Pucca Road (Except black top only taken out material to be used) 30%

Cutting the road as well as restoring the same as per specifications and as directed by Engineer incharge

Waterbound Macadam road (taken out material will be used) for cutting as per requirement 20% of the restoring work

Dismantaling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15 meter lead and disposal of unservisible materials with all leads complete as per direction of E/I

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of store chips 20 mm-6 mm size graded and clean coarsed sand of FM 2.5 to 3.0 including screeing shuttering mixing cement concrete in mixer and placing in position vibrating striking curing taxes and royalty alll complete as per building specification and direction of E/I

Earthwork in backfilling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-charge (Refilling )

Providing and supplying ISI mark centrifugally cast (spun) ductile Iron pipes of 100 mm and above all diameter for water works with sockets and spigot ends confirming to IS 8329/2000 in standard working lengths of 4.5, 5.5 and 6.0 M for classification K-7 and K-9 suitable for push on joints (rubber gasket D jointing) with cement mortar lining inside the pipes with outsides zinc and bituminous coating rate are ex-factory excluding transportation, taxes and duties contractor profit and over head charges etc. 10% CP Added. For Distribution System

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

Providing and supplying D.I. specials and fitting with sealing rubber gasket of SBR complete with cast iron follower gland and MS nut bolt coated or otherwise protected from rusting and suitable for DI pipes including ED, CST, all taxes etc. complete as per IS-9523. (Cost of specials = 5% of pipeline cost)

100 - 300 mm Dia.

Providing double flange sluice valve confirming for IS-2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all taxes transportation complete. (Sluice and scour valve ) Without by pass arrangement PN-1 with ED

100 mm dia

150 mm dia

200 mm dia

Twin Type Staff Quarter - 1 Unit (Please refer to Section 5,Sl. 2.7 of SBD)

E/W in Excavation in foundation trenches in ordinary soil (Vide classification of soil Item -A) & disposal of excavatd earth obtained to a distance up to 50 M including all lift leveling ramming the foundation trenches removing root of trees scrubs all complete as per approved design.

Providing ,coarse clean sand in filling in foudation trenches /in Plinth including ramming & watering in layers not exceeding 150 mm thick with all leads lift including cost of all materilas ,labour , royalty & taxes all complete as per building specification & direction Of E/I

Providing designation 75 A one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I

Providing P.C.C M-100 in nominal mix of (1:3:6) in foundation with appoved quantity of stone metal (50 mm 25 mm dia size)graded & clean coarse sand of F.M 2.5 to 3 including screening , shuttering , mixing cement concrete in mixer & placing in position , vibrating , striking , curing taxes & royalty all complete as per building specification & direction of E/I

Providing designation 75 A brick work in C.M. (1:6) in foundation 7 Plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including Providing 10 mm thick mortar joints ,Cost of screening , materials , Scaffolding , raking out joints to 15 mm depth curing , taxes & royalty all complete as per building specification & direction of E/I

Providing 25 mm thick damp proof coarse with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips of 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to3 including screening , shuttering mixing cement concrete in mixer with 5% cico or any other approved water proffing compound and placing in position , vibrating , striing , curing , taxes & royalty all complete as per building specification & direction of E/I

Providing designation 75 A brick work in C.M (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing10 mm thick motar joints ,cost of screening , materials, scaffolding,raking out joints to 15 mm depth curing , taxes & royalty all complete as per building specification & direction of E/I

Providing R.C.C M-150 with nominal mix of (1:2:4) in lintel level with approved quality of stone chips 20 mm to 6mm size graded & clean coarse sand of F.M 2.5 to including screening , centring, shuttering and mixing cement concrete in mixer & placing in position vibrating striking curing (but excluding the cost of reinforcement ) taxes & royalty all complete as per building specification of (E/I.

Centering and Shuttering

Providing average 63 mm thick R.C.C M -150 with nominal mix (1:2:4) chajja in shelves with approved quality of stone chips 20 mm to 6 mm size graded & clean coarse sand of F.M 2.5 to 3 including making drip course in concrete , screening , centering shuttering & mixing cement concrete in mixer & placing in position vibrating ,striking ,6 mm cement plaster (1:4) in celling & sides of chajja with sand of F.M 1.5, Curing ( But excluding the cost of reinforcement ) taxes and royalty all complete as per building specification of E/I

Centering and Shuttering

Door & Windows

Shelves

Providing R.C.C M-150 with nominal mix of (1:2:4) in roof slab with approved quality of stone chips 20 mm to 6 mm size Graded & Clean coarse sand F.M 2.5 to including making drip course in cocrete , screening , concreting , shuttering , centring mixing cement concrete in mixer & placing in position , vibrating ,striking, curing (but excluding the cost of reinforcement) taxes & royalty all complete as per building Specification & direction of the E/I

Centering and Shuttering

Supplying fitting & fixing good quality ,well dressed & well seasoned sal wood work in choukhat in doors , windows , skylights , fan light and C/W celestial windows openings , including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls & lintels all complete as per building specification & direction of E/I

Supplying fitting and fixing 250X20X6 mm L-type M.S Clamp properly fish tailed .including making holes and setting the same in 375 X125X75 mm cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and diection of E/I @6 for each door & 4 for each window Total Quantity -(2X3X6+2X4X4)=68 nos

Supplying all materials , labours and fitting & fixing 38 mm (1.5) thick good quality seasoned sal wood battened shutter ledged & braced in door and windows with oxidized iron fitting such as hingles ,sliding door bolts , tower bolts , handles or ings hooks and eye , cleats , sand block as per schedule , taxes & royalty all complete as per building specification & direction of Engineer -in- charge

Supplying , fittings & fixing M.S /Gril made of 20X6 mm M.S flat as per approved design & drawing properly fabricated with joints continous filllet welded and finshed smooth , carriage of grill to work site hoisting as per the building specification and direction of E/I ( where materials is not supplied by the Deptt .)

Providing 25 mm thick pre cast R.C.C M-150 with nominal mix of (1:2:4) in jali with approved quality to stone chips of 6mm nominal size and clean coarse sand of FM 2.5 to 3 with 1.6 mm thick M.S wire as per approved design and drawing and placing the same in position true to plumb and level and properly grouted with cement mortar (1:3) including cost of curing , Scaffolding and finishing all complete as per building specification and direction E/I

Providing and fixing fan hook of 16 mm dia M.S bar 1 meter long bent to reqired size and shape placed in position and fixing in R.C.C slab/beam at the time of casting all complete as per building specification of E/I where material is not supplied by cheet

Supplying , fitting and Fixing M.S Grill gate made of 20X 6 mm M.S or 16 mm M.S raurbar Flat fitted on 25 mm X 25 mm X 6mm M.S angle frame of size 60X60X6 as per approved design including cost of fabrication & drawing , properly fabricated with joints continuous fillet welded & finished smooth, providing necessary locking arrangements with Haskell & dummy duly fixed in C.C (1:2:4) blocks of reuired size applying a priming red lead paints over steel works , taxes , carriage of grill to work site , asper the building specification & direction of E/I ( where materials is not supplied by the Dept)

Providing 6 mm thick cement plaster (1:4) in celling with approved quality of clean coarse sand of F.M 1.5 including screening , curing with all leads & lifts of water , scaffolding , taxes & royalty all complete as per building specification & direction of E/I

Providing 12 mm thick cement plaster (1:6) with approved quality of clean coarse sand of F.M 1.5 including screening .Curing with all leads & lifts of water , Scaffolding , taxes 7 royalty all complete as per building specification & direction of E/I.

Providing cement 1:3 (12mm ) plaster with cement mortar (1:3) using clean coarse sand finishing with neat punning a dado 6" (150 mm) high a side room and out side wall upto plinth level includng screening , curing with all leads & lifts of water , scaffolding , taxes and royalty all complete as per building specification & direction of E/I

Filling in foudation trenches & Plinth in layers not exceeding 150 mm thick well watered ,rammed ,fully compacted & fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 m & lift of 1.5 m all complete as per building specification & direction of E/I ( Mode of measurement compacted volume)

Providing 25 mm thick . First class patent stone flooring (1:2:4) with stone chips in two layers ,bottom layer 19 mm thick (1:2:4) with 12 mm to 6 mm size graded stone chips and top layer 6 mm thick (1:2) with 6 mm down stone chips in pannels including cost of curing , finishing the surface smooth by rubbing with carborandum stone taxes & royalty with all complete as per building specification & direction of E/I

Providing designation 75 A one brick on edge flooring in C.M (1:4) with top surface flush pointed in CM (1:4) approved quality of clean coarse sand of F.M 2 to 2.5 including the cost of screening ,raking out joints to 15 mm depth , curing taxes,royalty all complete as per building specification and direction (E/I)

Providing all materials , labours & doing two coat snowcem with approved quality of lime over the new surface including the cost of cleaning surface thoroughly and removing the scales of smoke & ash marks with jhama rubbing ,scaffolding washing of floor sand taxes all complete as per building specification and direction of E/I

Providing all materials,labours & doing 2 (two ) Coat colour washing over a coat of white washing over new surface with approved quality of lime & Colour over the new surface including the cost of clening surface thoroughly and removing the scales of smoke & ash marks with jhama rubbing , scaffolding washing of floor sand taxes all complete as per building specification and direction of E/I

Providing two coats of painting with readymix paint synthetic enamel paint over a coat of primer of approved shad and make over new wooden surface after cleaning, removing dirt scales ,smokes,grease and sand papering including cost of scaffolding and taxes all complete as per building specification & direction of E/I

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning , removing rust ,dirt ,scales ,smokes and grease and cleaning the surface thouroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I

Providing 2(two) coats of Paniting with ready mixed paints of approved shade & make over steel surafce including cleaning the surface thouroughly , scaffolding & taxes all complete as per building specification & direction of E/I

Providing 10 mm (TMT) Fe 500 TOR for steel reinforced as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire with cost of wore removal of rust placing the rods in position all complete as per building specification and direction of E/I

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit, loading, unloading, transportation, etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Bricks 6 KM lead

Stone/Stone Chips 11 KM lead

Water Supply Sanitation Installation (Plumbing work)

Supplying and laying GI pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes in size and threading ends where necessary including carriage of materials up to work site etc. all complete as per specification and direction of E/I.

i) 25mm GI. Pipe.

ii) 15 mm GI. Pipe.

Supplying materials and labours for fixing GI Pipes with red lead paints and yarn with screwed and sockted joints on wall, celling and floor including supplying of wall hooks of pipe clamp, wooden plugs, cutting pipe to size and threading ends where necessary all complete as per specification and direction of E/I.

i) 15 mm GI. Pipe

Supplying, fitting and fixing of GM ferrule of approved make in DI/CI main including drilling and tapping CI/DI main etc. all complete as per specification and direction of E/I.

Supplying and fixing GI fittings of approved make all complete as per direction of E/I.

(a) Elbow 15 mm dia

(b) Tee plane 15mm dia

(c) Nipple 15mm dia.

(d) Union Socket 25mm dia

(e) Union Socket 15mm dia

(f) Brass bib cock 15mm dia

(g) C.I stop cock 15mm dia

(h) C.I. stop cock 25mm dia

(i) Reducing Socket 25x15mm

(j) Tee 25x25x15mm dia

Supplying, fitting and fixing vitreous white glazed earthen were I W C of parry Hindustan or any other I.S.S approved make with 100 mm HCI ‘P’ trap, 15 Liters CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings C.I. or C.C brackets, 32 mm, alkathene /PVC telescopic flush pipe about 2 mtrs. long with one brass coupling and clamps, GI chain and pull including supplying and fixing a pair of vitreous white glazed earthen were footrest to be fixed in floor, 15 mm .CI body brass spindle, stop cock of weight not less than 50 grams, 15 mm. PVC connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. (510mm.long with 12.5 Liter low level PVC System).

SEPTIC TANK and SOAK PIT

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-B) and disposal of excavated earth as obtained to a distance up to 50 m including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one Brick flat soling, joints filled with local sand including cost of watering, tax, royalty all complete as per building specification and direction of E/I.

Providing P.C.C M150 with nominal mix of (1:2:4) in foundation with approved stone chips 20mm to 6mm size well graded and clean course sand of FM-2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, Vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing water proof cement plaster (1:3) with clean course sand of F.M- 1.5mm with 5% cico or any other approved water proofing compound including taxes and royalty all complete as per building specification and directions of E/I.

(a) 19 mm thick

(b) 12 mm thick

Providing designation 75A bricks work in C.M. in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints, cost of screening materials racking out joints to 15 mm. depth, curing taxes and royalty all complete as per building specification and direction of E/I.

(a) B/W in C.M (1:4)

(b) B/W 75-B in (1:6) for Soak pit

(c) Brick work in dry masonry for soak pit.

Providing pre cast R.C.C. M-150 with nominal mix of (1:2:4) slab of desired size with approved quality of stone chips and clean coarse sand of FM 2.5 to 3 including curing, shuttering, carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement), taxes and royalty etc. all complete as per building specification and direction of E/I.

Providing for reinforcement as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per Specification and direction of E/I.

10 mm dia

Supplying fitting and fixing H.C.I. Pipe/ H.C.I. fitting of Approved make confirming to I.S.S 1729 including supplying nails and bobbins lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.

(a) 100mm dia H.C.I. Tee.

(b) 100mm dia H.C.I. Band

(c) 50mm dia H.C.I. Cowel

(d) 50mm dia H.C.I. Vent pipe

(e) 100mm H.C.I. Pipe

Supplying materials and labours and fixing 20mm dia M.S bar steps in wall of 0.3 m interval and staggered in (1:2:4) cement concrete including scaffolding and curing etc. all complete as per specification and direction of E/I.

Supplying all materials, labours, tools and tackles and 100mm dia R.C.C hume pipe and laying jointing, testing, earth work including carriage of materials etc. all complete.

Supplying 50mm size brick bats and filling in soak pit including carriage and labours etc. all complete as per direction of E/I.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475 mm G.I. Cover With frame ( Weight not less than 36 Kg.) along with earth work in excavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I

Carriages of materials

(a) Brick –6 KM lead

(b) Sand -36 KM lead

(c) Stone chips -11 KM lead

(d) Steel 10 KM

(d) Cement- 10 KM lead

Electrical Works

Point wiring in PVC conduit with modular type switch wiring for light point /fan point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for twin control light point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit with two way modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for light /power plug point with 2 x 4 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with one no 4 sqmm FR PVC insulated copper conductor single core cable for loop earthing etc as required

Copper sub main wiring in PVC conduit Wiring for sub main wiring with PVC insulated copper conductor single core in surface/recessed PVC conduit as required

2 x 1.5 sqmm + 1 x 1.5 sqmm earth wiring

2 x 2.5 sqmm + 1 x 2.5 sqmm earth wiring

Supplying and fixing following way three pole and neutral sheet MCB distribution board 415 volts on surface/recessed complete with tinned copper bush bars ,neutral link, earth bar, din bar, detachable gland plate inter connection phosphatised and power painted including earthing etc as required (but with out mcb / rccb / Isolator) (4 +12 ) double door horizontal type

Supplying and fixing 5 amp to 32 amp, rating 240 volts, B series miniature circuit breaker of single poles in existing MCB DB complete with connecting ,testing, and commissioning etc as required

Earthing with G.I. earth pipe 4.5 M long 40mm dia including accessories and providing masonry enclosure with copper plate having locking arrangement and watering pipe etc with charcoal ,salt all complete as per electrical rule

Supplying ,fitting and fixing following sizes of PVC conduct along with accessories in surface / races including cutting the wall and making good the same in case of recessed conduit as required

PVC con 20 mm PVC pipe

PVC con 25 mm PVC pipe

Installation commissioning and testing Ceiling Fan

Carriage of ceiling fan and regulator

Supplying ,fitting and fixing 5 amp ceiling rose on the existing junction

Supplying ,fitting and fixing breas batten/ angle holder including connection etc.

Supplying ,fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 3 pin 5/6 amp modular type switch, connection, painting etc as required.

Supplying ,fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 6 pin 5/6 amp and 15/16 amp socket outlet and 15/16 amp modular type switch, connection, painting etc as required.

Supplying and drawing co-axial T.V. cable RG-06 grade 0.7 nn solid copper conductor PE insulated seilded with fine tinned cover braid and protected with PVC sheath in the existing surface / recessed steel/ PVC conduit as required.

Supplying and fixing modular switch / socket on the existing modular plate and switch box including connection but excluding modular plate etc,as required. TV antenna socket out put

Supplying ,fitting and fixing modular base and cover plate on existing modular metal boxes etc as required.

Cost of Earthing with G.I. earth pipe 4.5 M long 40mm dia G.I.Pipe 600mm x 600mm x 6mm thick copper earth plate, and 8 SWG copper wire including cost of making 1.2x1.2x3m deep pit and filling with charcoal ,salt all complete as per electrical rule

Compound Wall/ Boundry Wall for WTP. (509.20 M Long)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority Construction of Compound wall. etc. all complete job.(Please refer to Section 5,Sl. 2.9 of SBD)

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item A) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering and Shuttering

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering and Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in stiffeners with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Centering and Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering and Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at lintel level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering and Shuttering

Providing designation 75 A brick work in CM (1:6) in super structure with approved quality of clean coarse sand of FM 2 to 2.5 including, providing 10mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of FM 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification & direction of E/I. Qnty. Same as Item no.13

Providing Tor steel reinforcement of 10 mm ,12 mm , &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site , cutting ,bending and binding with annealed wire with cost of wire ,removal of rust , Placing the rods in position all complete as per building specification and direction of E/I

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I

Carriage of materials from divisional store or kiln site or quarry site to work site including contractor's profit, loading, unloading, transportation etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Bricks 6 KM lead

Gate - 3 nos.

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item A) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering and Shuttering

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering and Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in column with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Centering and Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering and Shuttering

Providing Tor steel reinforcement of 10 mm ,12 mm , &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site , cutting ,bending and binding with annealed wire with cost of wire ,removal of rust , Placing the rods in position all complete as per building specification and direction of E/I

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I

Supplying fitting & Fixing M.S. grill gate with M.S. grills made 20x6mm M.S. flat or 16mm M.S. square bars fitted 25x25x6 mm M.S. angle frame of size 60x60x6 mm including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C (1:2:4) blocks of required size, applying a priming red lead paint over steel work , taxes all complete as per drawing specification and direction of E/I.

Providing two coat of painting with ready mixed paint of approved shade and make over steel surface

Carriage of materials from divisional store or kiln site or quarry site to work site including contractor's profit, loading, unloading, transportation etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Bricks 6 KM lead

Infilltration Gallery

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, outlet, intake well etc. as per designed section in all kind of soil including moorum soil, soil mixed with kankar, pebbles & boulders upto 300m size & disposal of the same (beyond 50 m away from the edge of the trenches) with initial lead of 150 M & initial lift of 1.50M as per specification & direction of E/I.

Initial lift

1st lift

2nd lift

Providing and supplying ISI mark centrifugally cast (spun) ductile Iron pipes of 100 mm and above all diameter for water works with sockets and spigot ends confirming to IS 8329/2000 in standard working lengths of 4.5, 5.5 and 6.0 M for classification K-7 and K-9 suitable for push on joints (rubber gasket D jointing) with cement mortar lining inside the pipes with outsides zinc and bituminous coating rate are ex-factory excluding transportation, taxes and duties contractor profit and over head charges etc.

Header pipe - 250 mm Dia DI - K9 Pipe

Supplying labours, tools and tackles, lubricant etc. for laying and jointing C.I.S/S tyton pipes (class LA) trenches supplying rubber gasket (Rubber gasket confirming to I.S.S.-5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete (Pipe to be supplied departmentally free of cost and laying of pipes is to be done as per I.S.S. 3114-1985) as per design, specification and direction of E/I.

Header pipe - 250 mm Dia DI - K9 Pipe

Providing, lowering, laying and placing in position, shrouding material for porous pipe gallery / slotted pipe gallery / trench gallery with all leads and lifts involved including transportation of materials to site of works, screening and washing of materials and placing in position with given section, etc. complete as directed by Engineer-in-charge.

(7 pipes of 8 m length)

40 mm pabbles

Design and Supply of V - wire screen laterals Suitable for Infiltration Gallery as per site condition and detail provided end connection suitable flange.

Dia - 06 inch (150 mm)

Providing and supplying D.I. specials and fitting with sealing rubber gasket of SBR complete with cast iron follower gland and M.S nutbolt coated or otherwise protected from rusting and suitable for DI pipes includingcost of labour, materials, and transportation to stores/ site, loading and unloading including all taxes etc. complete as per IS-9523.

100 to 300 mm dia

Coffer Dam

Providing, constructing coffer dam in river basin / dam storages as per type design including excavation, filling the middle portion with B.C. soil (in gunny bags if required). Providing impervious / semimpervious materials on both side of B.C. soil (in gunny bags if required) including ramming , compacting to satifaction of Engineer-in-charge, till the completion of work including dismantling coffer dam after completion of works and disposing off material as directed by the Engineer-in-charge.

Intake

Gangway

Infiltration Gallery

Dewatering the excavated trenches and pools of water in the building trinches/pipe line trenches , well works by using pumps and other devices including disposing off water to safc distence as directed by Engineer- in -charge (including cost of machinery , labour fuel, etc. complete

Intake

Gangway

Infiltration Gallery

House Connection for 3475 nos Consumer.

Earth work in excavation ( as per I.S. 3114/1965 for laying of different types and sizes of pipes so as to give 1 m av. cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/l. (For soil item A)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Provinding P.C.C M-150 with in norminal mix of (1:2:4) in foundation with approved quality of stone chips 20mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including , screening , shuttering, mixing cement concrete in mixture and placing in position vibrating striking curing taxes and royality all complete as per building specifiaction and direction of E/I

Centering and Shuttering

Earth work in back fillingthe trenches after laying of different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I.(For soil item A & B)

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and supplying blue MDPE pipes confirming to ISO 4427:1996 manufactured from vergin resin PE 80 food grade compounded raw material having blue colour only assurance certificate from quality agencies like WRC / CIPET ( India) / DVGM / KIWA / SPGN etc. for usage in drinking water with quality system. The cost shall including cost all taxes, inspection charges transprotaion to work site and earth work involved , all complete job as per specification and direction of E/I. 20 mm dia pipe.

Providing and supplying G.I. pipes (Tata and equivalent make) for usage in drinking water with quality system, The cost shall include testing of all materials all taxes central , State , Municipal, Inspection charges transportation up to site transite insurance, loading, unloading, stacking etc. complete as specified and directed.

Lowering laying and jointing HDPE / MDPE pipe in proper position including all specials by Compression fitting / Electrofusion and But fusion jointing procedure including hydraulic testing as er relevent IS Code complete with all materials for jointing procedure like Electrofusion machine ,Electric mirrior/heater/But fusion welding machine with hydraulic testing and all labours as directed by engineer in charge as per IS-7634 part II

Supplying labour and tools for fixing G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketted joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of E/l. (Pipe with socket to be supplied deparmentally free of cost).

Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dia ferrule weight not less than 425 gram

Providing and fixing gun metal full way valve of approved quality all complete as per specification and direction of E/ (a) 20 mm dia and weight not less than 400 gram.

Providing and fixing 15 mm Dia male ended C.I Body Brass Spindle valve and seat bib cock of approved quality (Wt.not Less than 400 gms.) with extra socket all complete as per specification and Direction of E/I.

Supplying and fixing G.I. fittings of Approved make all complete as per specification and Direction of E/I

Elbow 20 mm

Elbow 15 mm

Reducing Socket 20 mm

Nipple 20 mm

Nipple 15 mm

Union Socket 20 mm

Socket 15mm

Socket 20 mm

Carriage of materials

Operation & Maintenance for Five years

O/M work with Labour component & Materials for 1st Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 2nd Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 3rd Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 4th Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 5th Year

As per SBD Section - 5 Clouse 9.10

Labour Cess @ 1%

SANJAY KUMAR SHARMA ENGICON PRIVATE LIMITED