PROVISION OF MEDICAL STORE AT 320 FD HOSP AND SPECIAL REPAIR OF BLDG NO 1/ 2/ 2 AT BINNAGURI MIL STN UNDER GE (N) BINNAGURI

Amount

Schedule 'A'

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

M and L for PCC 1:2:4 type B-0, (using 12.5mm graded aggregate) in roof kerbs, padding concrete over roof or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M&L for 10mm thick screed bed or bedding layers in cement mortar (1:4) in order to maintain proper slope over existing roof surfaces for laying APP base polymeric membrane, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top :- (a) Applying bituminous primer @ 0.4 ltrs per Sqm over plastered surfaces of roof incl parapet surface. (Note :- Bituminous primer shall be "TANK MASTIC" manufactured by "EMUFALTE" manufactured by M/s Texsa India Ltd. or equivalent ) (b) Over the priming coat laying one layer APP based polymembric membrane of approved manufacturer 3 mm thick weight not less than 3.6 Kgs per Sqm reinforced with non woven polyester febric . Polymeric membrane shall be taken to a height of 60cm (min) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note :- (i) Laying APP based polymeric membrane shall be done torch on method or as per manufacturer's instructions. (ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturer's instruction. (iii) APP based polymeric membrane shall be " 3MM" thick manufactured by M/S Texsa India Limited or equivalent. (iv) Applying two coats of Aluminium paint over APP membrane.) (V) Cutting groove in brick wall 75 mm wide and 65 mm deep and shoping horizontal face of groove with cement mortar 1:3

Taking down Chowkats or frame exc 1.5 SqM but n.exe 4 Sqm each without taking off shutters from the frame complete all as specified and as directed.

Taking down shutters of any description exc 1 Sqm and n.exc 2.00Sqm each and removing from site complete all as specified and as directed.

S&F of pressed steel framed for door with one or more rebates including necessary fixing lugs, hinges, lock strike plates, size of frame 125 X 60 mm,complete all as specified and as directed.

S&F of factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19x19mm MS square tube and 1.2mm wall thickness complete all as specified and as directed.

S&F of 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F for factory made 35mm thick 2nd class hard wood gauged and skeleton shutter open rebated and prepared to received gauge etc (without sash bars) for fly proof door shutter, edges of framing plain, chamfered or rounded, fitted with cut of any mitred beads for securing gauge etc, size of members of shutter as specified in SSR Part-I section 8 clause No.8.23(a) and fitted to chowkats complete all as specified and as directed.

S&F of factory made solid panel PVC door shutter, 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails MS frame shall be covered with heat moulded plain color PVC `C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stile and plain color PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying & fixing in the frame at site as per manufactures instruction, complete all as specified and as directed.

S&F of mild steel butt hinges, medium weight cold rolled of size 100mm complete all as specified and as directed.

S&F of aluminium handles cast type anodised 150mm of size complete all as specified and as directed.

S&F of 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S & F 150 mm long Mild steel barrel tower bolts, stove enameled black, with bright bolt complete all as specified and as directed.

S & F 150 mm long Mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

S&F Aluminium alloy anodised sliding door bolt 250 mm long with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed.

S&F in repair steel window with side hung shutters incl. projecting type hinges with steel handles steel peg stay fixing lugs complete with glazing bar 10 cm devetailed or welded incl shop coat red oxide primer compete all as specified and as directed.

All as ser item No 18.00 here-in-above but without glazing bars complete all as specified and as directed.

S&F in repair steel ventilator top hung shutter including hinges, steel peg stay, fixing lugs etc complete with or without glazing bars all as complete all as specified and as directed. by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for preparation of new of previously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new or previously undecorated wooden surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of Pink primer complete all as specified and as directed.

M&L for preparation of old or previously undecorated wooden surface of any description, not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of one of previously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coats of red oxide primer complete all as specified and as directed.

Hacking out old broken unserviceable glass panes (any thickness, size, quality or description) for metal frame including punching or drilling out old glazing pins/spring clips and providing & fixing new one complete all as specified and as directed.

S&F of 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for PCC type C-1, 1:3:6 using 20mm graded aggregate as in bed block for fixing of hold fast, filling concrete in frame filling , gaps in between glazed & fly proof steel window, cills, railing up to 60 cm in height etc including necessary form work as required all complete all as specified and as directed.

S&F in stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

Taking down cement plaster on wall of any description incl racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick walls or concrete surfaces in mixed with water proofing compound by weight of cement or as per manufacturer instructions, finished even & fair without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick cement plaster on ceiling cement mortar (1:3) complete all as specified and as directed.

M&L for rendering 15 mm thick cement plaster on other than fair surfaces of brick work in cement mortar (1:6) complete all as specified and as directed.

Supply only intergral water proofing compound complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises including taking down cement plaster complete all as specified and as directed.

M&L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

M&L for 15mm thick screed bed or bedding layer of cement mortar 1:6 for floor finishes complete all as specified and as directed.

M&L non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L Glazed ceramic coloured tiles in vertical surface 350x250x7/450x350x7mm thick set and jointed in neat cement slurry and pointed white or colour cement to match complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces to receive a wall tiles using cement mortar 1:4 complete all as specified and as directed.

M&L for non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for for preparation of newly wall plastered surfaces and applying two coats of oil bound distemper on wall complete all as specified and as directed.

M&L for for preparation of newly ceiling plastered surfaces and applying three coats of whitewash on wall complete all as specified and as directed.

M&L for two coat of acrylic exterior emulsion paint and preparation of new surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 15 mm bore complete all as specified and as directed.

S&F of Tubes, medium grade, 15mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed.

Refixing of old steel tubing and conections in new or old position (wall, ceiling, floors, etc) of 15 mm bore complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth in brick walls complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 20 mm bore complete all as specified and as directed.

S&F of Tubes, medium grade, 20 mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed.

S & F in repair consealed stop cock CP, cast copper alloy fancy type with long shank and cup for 15mm pipe. complete all as specified and as directed.

S&F in repair 15 mm dia brass chromium plated angle cock complete all as specified and as directed.

S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and as directed.

S&F for 15 mm Bib taps of fancy type , cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size including CP waste coupling, PVC connection 450 mm long, waste pipe & removing the existing Basin, cutting for and pinning ends of brackets or erecting stand complete all as specified and as directed.

Supply and Fix in repairs 15 mm bore pillar taps, capstan head, cast Copper alloy, chromium plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair vitreous china urinal flat back size 465x355x265 mm white (minimum) with grating and union for discharge pipe incl connecting pipe & waste pipe complete all as specified and as directed.

S&F EWS Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flushing cistern and flush pipe) with 'P' or 'S" trap from or back inlet etc including connection to trap tend flushing pipe and provision of lime concrete bedding complete all as specified and as directed in repairs including demolition of existing one complete all as specified and as directed.

S&F in repair of CP health faucet complete all as specified and as directed.

S&F for 75 mm PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F grating doom 125mm dia with waste hole of PTMT (min wt 40 gms) complete all as specified and as directed.

Dismantling water tank exc 500 & n.exc 1000 ltr capacity and removing to store all as specified as directed

S&F 500 ltrs capacity rotational moulded polyethylene water storage(cylindrical vertical with closed top) hoisted and fixed in positions all specified in SSR Part I complete all as specified and as directed.

S&F 1000 ltrs capacity rotational moulded polyethylene water storage(cylindrical vertical with closed top) hoisted and fixed in positions all specified in SSR Part I complete all as specified and as directed.

S&F in repair of ball valves of 20mm bore high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed (Minimum weight 20 gms-210 gms)

S&F 110mm dia PVC SWR bends of any radius with out access door complete all as specified and as directed

S&F 110mm dia PVC (SWR) junction single 'T' equal or unequal with access door complete all as specified and as directed.

S&F 110mm dia PVC (SWR) branch piece, single ‘Y‘ equal or unequal Complete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L RCC type B1 (1:1.2:4) using 20 mm graded aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Formwork to fins, louvers, fascia. etc Fair finished surfaces of concrete flat complete all as specified and as directed.

M&L Mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and as directed.

M&L for one coat of white wash on ceiling of old surface with preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and as directed.

M&L for one coat of oil emulsion distemper with preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and as directed.

M&L for two coat of acrylic exterior emulsion paint of complete removal of existing paint and preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and as directed.

S&F in repair aluminium body door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and as directed.

S&F in repair anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc with applying 50 micron thick of any colour powder coat complete all as specified and as directed.

S&F in repair anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. with applying 50 micron thick of any colour powder coat complete all as specified and as directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in Soft/loose soil complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Soft/loose soil complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for hard core of gauge n.exc 63 mm and deposited spread and levelled in layers n. exc 15 cm thick, watered and rolled / rammed to a true surface with broken stone or boulders complete all as specified and as directed.

M&L cement concrete (1:3:6) type C-2 (using 40mm graded aggregate) in foundation, filling, mass concrete complete all as specified and as directed.

M&L for formwork to chajjas including edges rough finished surface of concrete flat complete all as specified and as directed.

M&L for RCC design mix M-25 with using 20mm graded aggregate as in foundation, footing, plinth beam etc complete all as specified and as directed.

M&L for RCC design mix M-25 with using 20mm graded aggregates in Chajjas complete all as specified and as directed.

M&L for RCC design mix M-25 with using 20mm graded aggregates as in lintels upto 1.50 M, cills, seismic and other type bands including using necessary formwork complete all as specified and as directed.

M&L brickwork with fly ash bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete all as specified and as directed.

M&L for 40mm thick Damp proof course in cement concrete 1:2:4 type B0 with using WPC at the rate of 3% by weight of cement and using necessary formwork complete all as specified and as directed. Note: Integral water proofing compound shall be measured and paid separately.

S&F factory made 30mm thick solid PVC shutter partly gauge and partly panel i.e upper panel will be wire guage, the wire gauge shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S tubes & lower panel will be plain colour PVC sheet shall be fitted in the M.S framewelded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement and frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having aPVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bnottom rail all as per specification and drawing complete all as specified and as directed.

S&F 300 mm length of bolt aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed type C-21 complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per ser item No 97.00 here-in-above but 8mm dia and over TMT bars upto and including 10mm dia in stirrups, spacers and binders and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F of rolled mild steel tubular sections as in roof trusses (framed), trussed, purlins, crane gantry, rails, fastening, heavy bracket framing (Beam, tee, angle, channel or flat section ,Tube etc), including distance pieces, cleats etc. confirming to Fe - 410- W including cutting, welding & necessary fittings such as nut bolt, plate etc. complete all as specified and as directed.

S&F steel work in tubular trusses MS pipes in vertical column including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161 1979 grade st 240 with one shop coat complete all as specified and as directed.

M & L for mild steel angle or other section cut to length, welded, fixed independently as in door frames complete all as specified and as directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as spd complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed.

M&L 75mm thick PCC (1:3:6) type C2 as in as in footpath to receive top layer or tiling using 40mm graded stone aggregate, finishing cement concrete surface even and fair without using extra cement complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 with using 40mm graded stone aggregates as in plinth protection laid in panels and finished even and fair including necessary form work complete all as specified and as directed. Note: Joints 12mm wide joints to full depth of PCC shall be provided at every 3 meters interval and at every change of direction and shall be filled with mixture of bitumen and sand in 1:3 by weight . Cost of provision shall be deemed to be included in quoted rate of this item.

M&L for providing 75 mm thick cement concrete type D-2, 1:4:8 using 40 mm graded aggregate as in sub base of floor finished rough to receive floor topping complete all as specified and as directed.

S&F 150 micron thick polythene sheet with 150mm lapping at side and ends complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B-0 with using 12.50 mm graded stone aggregates as in sub base of flooring, finished even and rough to receive the top layers all complete as specified and as directed.

M&L Non - skid Ceramic tiles(colour) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed.

M&L Non - skid Ceramic tiles(colour) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting/dado etc. set and laid over 10mm thick rendering in cement mortar (1:4) and pointed in white or coloured cement to match etc complete all as specified and as directed.

M&L 25 mm thick pre-polished coloured chequred tiles made with using grey cement and pigment, smooth finish exterior grade precast heavy duty shine finish paver tiles laid over 15mm thick screed in CM 1:6, set & jointed and pointed with grey cement and pigment complete all as specified and as directed.

M&L for preparation of newly plastered or un plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying two coats of wall putty to wall surface to get even and smooth surface complete all as specified and directed.

M&L for two coats of colour wash on new plastered surfaces incl preparation of surfaces complete all as specified and as directed.

S&F of 4mm thick 'E' classic designer board false ceiling with powder coated GI snap grid frame work of grid size 600 x 600 mm including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type B 0 Cement motar 1:3 complete all as specified and directed including all necessary drilling and necessary arrangement to fix items as under :- (a) 27x27x0.55 mm thick GI angle powder coated duly plugged @ 600mm centre to centre alongwith perimeter of wall. (b) 25x25x0.55 mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders (n.exe 1.2 mtr length) with adjustable clamps and dash true fastners plugging in RCC slab/wooden truss/A.I Runner of slopped roof placed @ 600mm centre to centre from perimeter of wall. (c) Fixing of 4mm thick AC "E" Classic designer board of approved texture and finished complete. Note. The complete ceiling work shall be done as per manufactures instruction and as directed.

Taking down carefully old/unsv copper/alluminium any type of point wiring for one light, socket, fan, bell or power etc incl all fittings such as switches sockets, holders, light fittings, fan regulators, call bell etc and making good the disturbed surface of wall ceiling complete all as specified and as directed.

M&L for Concealed type Point wiring with 1.5 Sqmm (nominal cross-sectional area) PVC insulated unsheathed single core malti stranded copper FRLS cable working voltage 1100 volts grade conforming to IS-694 with stranded copper conductor in including PVC conduit of adequate size having a wall thickness not less than 1.5 mm with all accessories (including cutting chases & making good the disturbed surface to its original specification) including 1.5 sq mm (nominal cross sectional area) PVC insulated unsheathed single core multistranded copper conductor FRLS cable as earth continuity conductor connected to main switches/DB's or common earth dolly complete all as specified and directed for the following :- (a) One light point controlled by one way switch 5/6 amps.

(b) One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps.

(c) One socket out let 5/6 amps point on the independent board

(d) One socket out let 5/6 amps point on the same board

All as per item No 2 above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and as directed.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified and as directed.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and as directed.

S&F in switch piano flush type 15/16 amps single pole one way complete all as specified and as directed.

S&F Switch socket combination 2 and 3 Pin, 5/6 amps, multipurpose flush non shutter, non inter locking type white ivory finish with, complete all as specified and as directed.

S&F switch socket combination 2 in 1, 6 pin 5/6 amps and 15/16 amps multipurpose, white/ivory finish flush non shutter non inter locking type , complete all as specified and as directed.

S & F in repair deluxe fan Electronic regulator 120/280 volts AC 50 Hzs rotary step white/ivory finish complete all as specified and as directed.

S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and as directed.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and as directed.

S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and as directed.

S&F in replacement of LED light fittings 1 x 18/20 watts 230 Volt white powder coated slim box type batten made of formed CRCA with snap on installer LED lighting fixture with and including 1x18/20 watt T8 double side connection retrofit LED tube with G13 lamp holders, connector block, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable up to cealing rose complete all as specified and as directed.

Taking down carefully Ceiling fan after disconnecting electric connection and refixing with and incl necessary paint and minor repair complete all as specified and as directed.

M&L for sub main wiring with 2 run of 6.00 sqmm (nominal cross-sectional area) PVC insulated unsheathed single core cable of working voltage 1100 volts grade with stranded copper conductor including one run of 6 Sqmm (nominal cross sectional area) PVC insulated unsheathed cable with stranded copper conductor as continuous earth wire connected to common earth dolly drawn in PVC rigid non- metallic conduit with and including taking down unsv sub main, complete all as specified and as directed.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Triple pole & neutral with 200 amps rated bus bar, 415Volt IP-20 protection suitable for fixing MCB"S/isolators with and including taking down old one complete all as specified and as directed.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/isolators complete with and including taking down old unsv one complete all as specified and as directed.

S&F MCB, Triple pole & neutral 63 amps, 240 volts, ‘C’ curve, 10KA complete all as specified and as directed.

S&F MCB, Single pole & neutral, 35 to 63 amps, 240 volts, ‘C’ curve, 10KA all complete with and including taking down old unsv one complete all as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unsv one complete all as specified and as directed.

Disconnecting and removing U/S building security light fitting of any type from bldg and Supply and fixing new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening separate driver compartment with IP 66 protection and impact resistance of IK07system of not less than 30 Watts IP 66 type incl standard fittings pressure die cast aluminium housing, heat resistant toughened glass, epoxy powder coated finish complete with Electronic driver, Surge protector not less than 5 KV and all accessories duly prewired complete all as specified and as directed.

M & L for street light bracket made out of GI pipe light grade 32 mm dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling, hole, fixing with nuts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified and as directed.

Supply & fix of Exhaust fans AC single phase 230 Volt of size 300 mm sweep with and including MS louver, Cutting of the wall should not be less than 25mm the sweep diameter complete all as specified and as directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, check nuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, includig necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 5 of SSR Part- I including testing on completion all as directed and as specified.

Supply and fixing of Sheet metal enclosures with socket two pin and earth plug top and MCB SP-20Amp 230 volt with and including taking down the old one complete all as specified and as directed.

S&F of socket outlet 2 in 1, 5 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and as directed.

S&F of LED bulk head fitting 1X10 Watt made out of pressure die cast housing with opal diffuser IP65 protection complete all as specified and as directed.

S & F building security light fitting of any type from bldg and Supply and fixing new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening separate driver compartment with IP 66 protection and impact resistance of IK07system of not less than 45 Watts IP 66 type incl standard fittings pressure die cast aluminium housing, heat resistant toughened glass, epoxy powder coated finsh complete with Electronic driver, Surge protector not less than 5 KV and all accessories duly prewired complete all as specified and as directed.

S&F Sheet metal enclosure for 12 way Distribution Boards (DB’s), double door, single pole and neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/isolators complete all as specified and as directed.

M&L for LED retrofit Lamp 1x14 Watt (white) 230V B-22 holder base with polycarbonate body and aluminium heat sink complete all as specified and as directed.

Supply & fixing of ceiling fans with all accessories 230 V,1200 mm sweep. BEE 5 star rated conforming 2 IS 374 : 1979 complete with pre wired with 3 core cable complete all as specified and as directed.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated , FRLS screened, PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 16 sqmm 2 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. (NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A').

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / laying under ground electric cable complete all as specified and as directed.

Returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cms in depth complete all as specified and as directed.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed.

Supply and laying sub class B bricks of size 25cmx12.5cmx7.5cm (+/-10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed.

Supply and fixing 40 mm dia GI tubing light grade ISI marked laid in trenches/ laid under floor for protection of cable including all fittings such as elbow, bends, etc and short length complete all as specified and directed.

S&F of moulded case circuit bracket (MCCB) four pole adjustable type 415 Volt, 50 Cycle, 63 AMPs of breaking capacity 36 KA complete all as specified and as directed.

Scarifying or picking, gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 Sqm with depth exc. 50 mm but not exc. 100 mm including removing materials from site of work or stacking for re-use at site complete all as specified and directed.

Screening road metals, chippings, etc on the site of work where specially ordered including removing screened materials clear of screen and stacking in separate heaps for measuring complete all as specified and directed. (Material from both sides of screen measured)

Materials and Labour for 7.5cm thick (compacted thickness) WBM, with coarse aggregate of granite, trap or Basalt of grading 2 (63 to 40mm size), spread, rolled and consolidated to gradient and camber with 8 to 12 tonne power roller complete all as specified and directed.

All as per item No.163.00 here-in-above but except materials complete all as specified and directed (Note:- Serviceable materials shall be obtained from item No. 162.00 here in before for re-use).

M&L for preparing un-surfaced water bound macadam by brushing with wire brushes for removing caded mud etc sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc, providing evenly priming / tack coat with catonic emulsion (RS-1) @ 3.5Kg/ 10 Sqm complete all as specified and directed.

M&L for premix bituminous, macadam laid/rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) using paving bitumen VG-30 @ 4% (minimum) by the weight of total mix in hot mix plant laid, rolled and compacted to required gradient and camber with 8 to 12 tonne power roller complete all as specified and directed. NOTE : No extra allowances shall be admissible to the contractor if the bitumen content is required more than 4% by the weight of total mix as per approved design on minus side and it will be recovered @ Rs. 50.00/kg of bitumen irrespective of any purchase price. The contractor shall quote the rate accordingly.

M&L for preparing of existing black top surfaces of road and raw bituminous macadam surface by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags or by air compressor to remove all loose dirt etc and applying evenly a priming / tack coat with cationic bitumen (RS -1) @ 2.5Kg/per 10Sqm to receive Bituminous macadam and SDAC complete all as specified and directed.

M&L for bituminous premix asphaltic semi dense concrete 30mm consolidated thickness (minimum) with 5.5% binder content of paving bitumen Gde-VG-30 by weight of total mix, rolled and compacted, mixed in mechanical hot mixed plant and pre-mixed material laid with mechanical paver, finished including rolling to required gradient and camber with 8 to 12 tonne power roller to required compaction complete all as specified in the relevant clauses of SSR Part-I (2009) complete all as specified and as directed. Note : (a) The actual binder contain used shall be as per optimised content based on approved Job mix formula irrespective of whatever indicated above. (b) Rate deemed to be included for making good of any undulation/damages in wearing surfaces, where semi dense asphaltic concrete to be laid. (c) Price adjustment shall be done on minus side (without permissible tolerance on minus side) with reference to binder content indicated above and actually to be used in the work. (d) Price adjustment for paving bitumen shall be done @ Rs. 50.00 per KG for any variation on minus side irrespective of actual purchase rate. However, no adjustment for variation on plus side will be made.

M&L for 2.5mm thick painting to road surfaces as in lines, dashes, arrows, letters , zebra crossing etc on roads, pavements and like with thermoplastic road marking paint @ 5 kg/Sqm and applying glass beads @ 300 gms/Sqm over painted surfaces while the painted surfaces are hot by mechanical means including cleaning surfaces complete all as specified and as directed. (Note. The painting shall be carried out through mechanical appliances by the company's approved applicator).

S&F dual direction road studs, cats eye of impact ABS plastic / polycarbonate studs 100x90mm having colour (white. Red. Yellow) to a side provided with steel zonk plated nails of dia 4mm and length 60mm for fixing to road by hammering with adhesive including taking down old one) complete all as specified and as directed.

S&F energy saving, eco friendly water tight solar road studs made of aluminium die cast matt finish (Sand Blasted), with min 125x125x20mm with shank 56.8mm long including taking down old one complete all as specified and as directed.

M&L for Continuous brick edging (sub class 'B' brick, old size, best quality locally available) with width equal to the width of the brick; laid dry on end vertically including demolition of brick edging complete all as specified and directed.

M/s. MD IRSHAD

M/S VIRENDRA KUMAR SINGH