Construction of Party Plot for AMC at TP. no. 99 (Nana Chiloda) FP no 114, at Sardarnagar ward North Zone, Ahmedabad.

Name of Work:- Construction of Party Plot for AMC at TP. no. 99 (Nana Chiloda) FP no 114, at Sardarnagar ward North

Zone, Ahmedabad

Volume -II Financial BID

Ahmedabad Municipal Corporation

Rajiv Gnadhi Bhavan

Memco, Ahmedabad-382345

AHMEDABAD MUNICIPAL CORPORATION

MAHANAGAR SEVA SADAN - NORTH ZONE

Name of Work: - Construction of Party Plot for AMC at TP. no. 99 (Nana Chiloda) FP no 114, at Sardarnagar

ward North Zone, Ahmedabad

Bill of Quantities

SR. TOTAL SOR RATE

ITEM DESCRIPTION UNIT AMOUNT

NO. QTY 2025-26

Clearing and grubbing road land including uprooting

rank vegetation grass bushes,shrubs,sapling and trees

1 girth up to 300 mm removal of stumps of trees cut Hec 0.59 34451.77

earlier and disposal of unserviceable materials.(D) By

mechanical means in area of thorny jungle.

Barricading the entire break down or excvated area on

rental basis using wooden ballies / M.S.angles at max.

2.00 meter centre to centre, C.G.I. Sheet, reflective paint

/ Board out side to avoid accident & for smooth traffic

diversion & movement including cautionary board etc.

2 Item also includes for making temporary sufficient nos Rmt 589.91 80.35

of lighting arrangement through out the work with

necessary required arrangement. ..The same shall be

removed after completion of work. (Only for break

down work from start to complete) (Based on Drainage

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(A)

Loose or soft soil

Excavation for foundation for depth from 1.5 mt 3.0 m

including sorting out and stacking of useful materials

and disposing off the excavated stuff upto 50 Meter

lead.(A) Loose or soft soil

Conveyance charges of earth lime, murrum, building

5 rubbish, manure, garbage, sludge, excavated rock, fly Cmt 1888.00 408.41

ash, aggregate of any kind etc. comp. upto 5 km lead.

Extra For Lead Above 5 km & upto 6 km Cmt 378.00 417.67

Extra For Lead Above 6 km & upto 7 km Cmt 378.00 426.93

Extra For Lead Above 7 km & upto 8 km Cmt 378.00 436.19

Extra For Lead Above 8 km & upto 9 km Cmt 378.00 445.45

Extra For Lead Above 9 km Cmt 378.00 454.71

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

6 exceeding 20 cm. in depth consolidating each disposited cmt 3707.00 129.10

layer by ramming and watering.

Filling in plinth with sand under floors including

7 watering ramming, consolidating and dressing cmt 436.00 455.63

Filling in foundation and plinth with murrum or

selected soil in layers of 20cm. thickness including

watering, ramming and consolidating etc. complete.

Filling in foundation and plinth with brick Bats Chhara

9 in layers of 20cm. thickness including watering, cmt 367.00 594.61

remming and consolidating etc. complete.

Carring out plinth treatment to post construction

/existing structure by spraying chemical solution for

termite control treatment including labour and material

consistment with I.S.I specification. Using Chlordene

and Chiorpurfiles 20 EC. As Per 6131_paret-II

10 Consentration Weight one percent is recommended i.e Smt 349.00 104.90

one litre 20 EC chemical emulsion with 19 liter give 1%

concrentration inclusive of one litre chemical emulsion

appication at the rate of 5 Litre chemical /Sqm of sur

face is recommended as per I.S

Providing and laying cement concrete 1:3:6 (1-

Cement:3-coarsesand:6-hand broken stone aggregates

11 40mm nominal size)and curing complete excluding cost Cum 599.00 2976.00

of formwork in (A) Foundation and Plinth.

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

12 reinforcement for reinforced concrete work in (A) Cum 296.56 4238.04

Foundations, footings, Base of columns and Mass

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in ©

13 Slabs,landing,shelves,Balconies, Lintels, Beams, Girders Cum 149.00 4496.07

and Cantilever upto floor two level. : Plinth Beam

Providing and laying controlled cement concrete M.200

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in ©

14 Slabs,landing,shelves,Balconies Lintels, Beams, Girders Cum 257.00 4460.36

and Cantilever upto floor two level. : Ground Floor

Providing and laying controlled cement concrete M.200

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in ©

15 Slabs,landing,shelves,Balconies Lintels, Beams, Girders Cum 5.00 4500.21

and Cantilever upto floor two level. : First Floor

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

16 reinforcement for reinforced concrete work in (D) Cum 67.00 4593.91

Columns, Pillars posts and struts, upto floor two level. :

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

17 reinforcement for reinforced concrete work in (D) Cum 7.00 4633.76

Columns, Pillars posts and struts, upto floor two level. :

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

18 reinforcement for reinforced concrete work in © Cum 84.00 4496.07

Slabs,landing,shelves,Balconies Lintels, Beams, Girders

and Cantilever upto floor two level

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

19 reinforcement for reinforced concrete work in (B) Cum 20.00 4519.88

Walls, from top of foundation level upto floor two level

Providing TMT Bar FE 500D reinforcement for

R.C.C.Bwork including bending, binding and placing in

position complete upto floor two level

Providing TMT Bar FE 500D reinforcement for

21 R.C.C.Bwork including bending, binding and placing in Kg 2410.00 76.45

position complete upto floor two level

Providing formwork of ordinary timber planking so as

to give a rough finish including centering shuttering

strutting and propping etc. Height of propping and

centering below supporting floor to ceiling not

exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (A)

Foundations Footings Bases of Columns etc. and Mass

Providing formwork of ordinary timber planking so as

to give a rough finish including centering shuttering

strutting and propping etc. Height of propping and

centering below supporting floor to ceiling not

23 exceeding 4 M. and removal of the same for in situ Smt 237.00 252.00

reinforced concrete and plain concrete work in. (B) Flat

surfaces such as soffits of supspened floors slabs

Landings and the like. (1) Floors etc. upto 200 mm in

Providing formwork of ordinary timber planking so as

to give a rough finish including centering shuttering

strutting and propping etc. height of propping and

centering below supporting floor to ceiling not

exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (G)

Columns PillarsPosts and struts. (1) Square Rectangular

Polygonal in plan.

Providing formwork of ordinary timber planking so as

to give a rough finish including centering shuttering

strutting and propping etc. height of propping and

centering below supporting floor to ceiling not

25 exceeding 4 M. and removal of the same for in situ Smt 583.00 259.88

reinforced concrete and plain concrete work in. (H) (2)

Sides and soffits of Beams Beam Haunchings canti-

levers Girders Bressumers and Lintels exceeding 1M.in

Providing formwork of ordinary timber planking so as

to give a rough finish including centering shuttering

strutting and propping etc. height of propping and

centering below supporting floor to ceiling not

26 exceeding 4 M. and removal of the same for in situ Smt 171.00 229.85

reinforced concrete and plain concrete work in. (C)

Vertical surface such as walls (any thickness) partitions

and the like including attached buttresses & string

course & the like.

Providing formwork of ordinary timber planking so as

to give a rough finish including centering shuttering

strutting and propping etc. height of propping and

27 centering below supporting floor to ceiling not Smt 52.00 67.73

exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (I)

Edges of slabs and Breaks in floors and walls.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm. in

28 foundation and plinth in Cement Mortar 1:5. (1- Cement Cum 159.00 4011.66

: 5 -fine sand)(B)Conventional

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement

29 : 5 -fine sand)(B) Conventional Cum 189.00 4283.91

Extra for brick work in superstructure above plinth

level upto floor two level (B) Conventional : Ground

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement

30 : 5 -fine sand)(B) Conventional Cum 31.00 4326.00

Extraforbrickworkinsuperstructureaboveplinth level

upto floor two level (B) Conventional : First Floor

(i) Half brick masonry in common brunt clay building

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse

31 sand ) in foundation and plinth (B) Conventional Extra Smt 36.00 646.70

for half brick masonry in superstructure above plinth

level upto floor two level. (B) Conventional

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

32 interior plastering upto floor two level and finished Smt 1404.00 178.77

even and smooth in (ii) Cement mortar 1:4 (1-cement

Providing 10mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor

two level and finished even and smooth in (ii) Cement

33 mortar 1:4 (1- cement :4-sand) Extra over items 58 to Smt 273.00 135.77

71 for plastering on ceilings and sofits of stairs upto

floor two level instead of plastering on walls

20 mm thick sand faced cement plaster on walls upto

height 10 metres above ground level consisting of

34 mm thick backing coat of C.M.1:3 (1-cement:3-sand) Smt 444.92 297.68

and 8mm thick finishing coat of C.M.1:1(1-cement:1-

sand) etc. complete.

Providing 20 mm thick water proof cement plaster

using water proofing powder 1Kg/1bag of cement for

all floors on brick / concrete wall work using water

proofing materials in C M 1: 4 ( 1 cement 4 coasrse sand)

including finishing with a flooting coat of neat cement

35 slurry etc complete for all floor. and shall be guaranteed Smt 228.00 249.00

for minimum period of 10 years after handing over the

completed building by the main contractor to be

finished as directed. Stamp paper guarantee 10 years to

be furnished before receiving any payment from the

Providing & applying of Natura Texture Coating System

made from 100% natural grains and granules and

premium acrylic resin, silicon and other additives to

bind and protect to external walls, columns etc. of

approved made, shade, design & pattern. Application:

(i) 1st coat of primer based on acrylic resin which helps

the texture material to bind properly with base coat. (ii)

2nd coat of texture material of natural stone grains and

granules which is based on premium acrylic resin,

silicon, other additives and preservatives. (iii) 3rd coat

is clear coat of acrylic and silicon which provide surface

an extra strength and protect against water fall, provide

UV resistency as directed by Engineer-in-charge.

Providing cement vata (10cm. x 10 cm. size) quarter

37 round in cement mortar 1:1 including neat cement Rmt 200.00 23.45

finishing, watering etc. complete.

Applying two coats of putty & two coats of primer of

approved brand and manufacture on new wall surface

38 to give an even shade including thoroughly brushing the Smt 1677.00 40.19

surface free from mortar dropping and other foreign

matter and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

39 surface to give an even shade including throughly Smt 1677.00 78.40

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion

paint on wall surface (two coats) to give an required

40 shape even shade after thoroughly brushing the surface Smt 445.00 113.40

to remove all dirt, and remains of loose powdered

materials.etc complete

Providing and laying Ceramic tiles 6mm thick in flooring

treads of steps and landing laid on a bed of 12mm thick

41 cement mortar 1:3 (1-cement : 3- coarse sand ) finishing Smt 245.00 960.47

with flush pointing in white cement.

P & L 24" x 24" vitrified 8 mm thick tile flooring over

mm (average) base of cement mortar 1:6 ( 1 cement:

coarse sand) on new surface or fixing on existing

42 flooring by adhesive material including dismentaling of Smt 50.00 1178.10

existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the

surface etc. complete for light shade

P&L 24"x24" vitrified 8mm thick tile flooring over

20mm (average) base of cement mortar 1:6 (1cement :6

coarse sand) on new surface or fixing one xisting

43 flooring by adhesive material including dismentaling of Smt 71.00 1383.99

existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the

surface etc.complete for antiskid

Providing and laying white glazed tiles 6mm thick in

skrting risers of steps and dedo on 10 mm thick cement

plaster 1:3(1-cement :3-coarse sand)and jointed with

white cement slurry

Providing and fixing Min. 0.60 meter wide sandwich

type platform including supplying and fixing granite

stone 18 mm thick mirror polished stones in top and

side position and vertical strip at front over 25 mm

thick polished kota stone platform fixing in top and

45 sides and intermediates supports fixing with cement Smt 5.00 7350.80

mortar and adhesive and finishing including making

recess for Kitchen/ Laboratory sink etc. complete as

approved and directed by Consultant / EIC.

Providing and laying polished Kota stone slab flooring

over 20mm (Average) thick base of cement mortar 1:6

(1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty

46 :1.5 - coarse sand) laid over and jointed with grey Smt 280.00 982.83

cement slurry mixed with pigment to match the shade

of slab including rubbing and polishing etc. complete.

Providing and laying Granite slab (18 mm thick) one

side polished flooring over 20 mm (average) base of

47 cement mortar 1:6 (1 cement : 6 coarse sand) or L.M Smt 100.00 2144.00

1:1.5 laid and jointed with grey cement slurry including

rubbing and polishing complete.

Providing and laying 18 mm thick polished granite

stone machine cut in single piece (Max. available) in sill

and jambs of door ,window,ventilation & lift wall

cladding,staircase flooring landing, risers & treads,

skirting laid over 10 mm thick cement mortar 1 : 3 (1

48 cement : 3 coarse sand) and jointed with grey cement Smt 60.00 3279.00

slurry with matching pigment incl. rubbing and

polishing,half rounding edge and incl. fixing of hilty

fastener at every 1/3 span of sill as required size etc.

complete colour and shed as approved by architect

engineer in charge.

Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at

49 required spacings and frame alround, square or round Kg 557.00 100.17

bars with round headed bolts and nuts or by screws (A)

Providing and fixing standared extruded of alluminium

section of size 63mmx 38.10 mm x 1.2mm @Wt.0.643Kg

50 /mt with colour anodized alluminium frame for Smt 2.00 1163.92

ventilation with 5mm thick frosted glassas details etc

complete for Ventilation.

Providing and fixing window having extruded

aluminum Colour Powder Coated section frame main

outer size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094 Kg /

Rmt, horizontal two track member size 61.85 mm x

31.75 mm x 1.20mm @ wt.of 0.695 Kg/mt, vertical

member of size 61.85 mm x 31.75mm x 1.30 mm @ wt.of

0.0.659 Kg/mt with sliding shutters of horizontal

member size 40mm x 18mm x 1.29mm @ wt.of

0.456Kg/mt, vertical member of size 40mm x 18mm x

1.29mm @ wt.of 0.456Kg/mt with 5 mm thick

transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per

details etc complete for window

Providing and fixing single or double flush door both

sides laminated and I.T.W. beading all around by using

I.T.W. frame 120 m.m. x 80m.m.. shutter fabricated from

35 mm thick solid core malemine faced three layered

pre laminated flat pressed wood based exterior grade

bonded BWP/BWR synthetic resin having stamped IS

12823 grade I type II including three coats of lacquer

polishing to exposed wooden surfaces and Stainless

steel decorative type designs fixtures / fastening

etc.including I.T.W. triangular batten patti of size

30m.m.x30m.m.etc. as per architectural detailed

drawing and as directed by engineer in charge.

Providing and fixing FRP frame size 125x65mm and

mm thick FRP shutter with wood grain raised pannel

edde sign finish shutter having extra reinforcement on

sides & edges in Gel coat finish. The core of the shutter

& frame is to be filed up with injected polyurethene

53 foam done in situa long with embedded wooden pieces Smt 12.00 1999.98

for stiffening & also taking hinges & fintures. The whole

FRP frame &shutter is to be water proof weathe rproof

,termite proof & resistance to mild acid/alkali. Rate sare

to be inclusive of S.Shinges with fastener sleeve &

alluminium fixtures & fastenings.

Providing & Laying P21(water reducing concrete

admixture at 100 ml per bag of cement & recon 3 s fiber

at 125 gm per bag of cement including making C channel

75 x 75 mm required to maintain level,slope and

54 thickness of the concrete road leveling of placed Smt 1185.00 175.00

concrete with surface vibrator and finishing with power

floater & trowel light brooming the surface & including

cutting & filling of expansion joint as directed by

Engineer in charge.

Providing, laying, spreading and compacting Wet Mix

Macadam (as per table 400 - 10 and 400 - 11) of well

graded stone aggregate to specification including

premixing the Material with water at OMC in

mechanical mix plant as per approved design mix,

55 carriage of mixed material by Tipper to site, laying in Cum 237.00 1710.00

uniform layers with motor grade/Front end

Loader/paver finisher, in sub base/base course on a

well prepared under base and compacting with

vibratory roller to achieve the desired density including

lighting, guarding, barricating and maintenance of

diversion etc. (MoRTH specification : Clause 406) by

mechanical means

Providing and laying rubble soling, 23 cm thick, in a

compact manner, foudation, road, footpath etc. using

200 to 230 mm. cut size stones, covering and levelling

56 the surface with a layer of murrum after filling the voids Cum 273.00 1039.37

with smaller sized stones or stone chips, including

watering, ramming well and consolidating each layer, as

Providing and fixing pre-cast concrete kerb stone of

gray cement based concrete block 30cm length,30cm

height and 15cm thick of M250 grade concret as per

57 approved design and including excavation for fixing in Rmt 549.00 358.06

proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

Providing and fixing pre-cast Rubber Dye / steel Dye

inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated

58 mechanically and as per approved design Confirming to Smt 1835.00 680.10

IS 15658 : 2006 including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.

Providing and laying of Hot applied thermoplastic

compound 2.5 mm thick including reflectorizing glass

beads and 250 gms per Sq.m. area thickness of 2.5 mm

is exclusive of surface applied glass beads as per IRC-35

2015. The finished surface to be level/uniform and free

from streaks and holes or chipping of Thermoplastic if

any and including primer coat for C.C. surface and A.C.C.

surface, in white and/or yellow colour. Rate includes

brushing, blooming and cleaning and application of

paint. Zebra patta/Bump patta/Lane line/Center

line/Cut patta, Directional Arrow, Lettering MoRT&H

Clauses 803 &Volume II Part III and IRC 35-2015.Rate

shall include brushing, brooming, painting and

repainting of worn out paint after a period of 2.5 years.

Note:-As per drawings and design supplied by architect

and instruction given by authority and E.I.C.

Providing and laying waterproofing treatment for

terrace including applying neat cement slurry

kg/sq.mt. of cement admix with waterproofing

compound after cleaning the surface. (b) laying cement

concrete using brick bats 25 to 100 mm size with 50%

cement mortar 1:5 (1-cement : 5-coarse sand) admixed

with waterproofing compound over 20 mm thick layer

60 of C.M.1:5 to require slope including rounding of Smt 779.00 552.00

junction or walls and slabs (c) after two days of proper

curing applying a second coat of cement slurry. (d)

finishing the surface with 20 mm thick cement mortar

1:4 and finally finishing the surface with trowel As

directed with cement slurry. (e) after finishing the

whole terrace shall be flooded with water for a period

Providing and laying broken chine mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or slope

61 and to be tempered to bring mortar creme out upto Smt 273.00 739.89

surface using white cement including rounding off

junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed.

Structural steel work ( Confirming to IS 4923-1997)

riveted, bolted or welded in builtup for all type sections,

in framed work, including cutting, hoisting, fixing in

62 position and applying a priming coat of approved steel Kg 8610.00 126.68

primer all complete as per the

structural designs and directions of Engineer in

charge.Column ( 122 x 61 x 3.6mm )

Painting one coats (excluding priming coat) on

previously printed steel and other metal surface

63 with synthetic enamel paint, brushing to give an even Smt 295.00 43.79

shade including cleaning the surface of all dirt, dust and

other foreign matter.

Providing and fixing rolling shutters of approved make

made of 80 mm wide M.S. laths inter-locked together

through their entire length and jointed together at the

ends by end locks mounted on specially designed pipe

64 shaft with bracket plates, guide channels and Smt 10.00 3468.72

arragements for inside and outside locking with push-

pull operation including the cost of hood cover and

spring etc. complete.(A) Shutters having width below

Providing and laying cement concrete flooring 1:2:4 (1-

cement : 2-coarse sand : 4-graded stone

65 aggregate 20mm nominal size) laid in one layer and Smt 36.33 348.08

finished with a floating coat of neat cement. (B)

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

1 following dia. nominal bore tube fittings and clamps Rmt 200.00 165.21

including making good the wall, ceiling and floor etc.

complete.[A] 15 mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

2 following dia. nominal bore tube fittings and clamps Rmt 400.00 202.97

including making good the wall, ceiling and floor etc.

complete. [B] 20 mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

3 following dia. nominal bore tube fittings and clamps Rmt 400.00 247.25

including making good the wall, ceiling and floor etc.

complete. [C] 25 mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

7 following dia. nominal bore tube fittings and clamps Rmt 500.00 330.365

including making good the wall, ceiling and floor etc.

complete. [D] 32mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

5 following dia. nominal bore tube fittings and clamps Rmt 200.00 437.66

including making good the wall, ceiling and floor etc.

complete. [E] 40mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

6 following dia. nominal bore tube fittings and clamps Rmt 300.00 647.3

including making good the wall, ceiling and floor etc.

complete. [F] 50mm.

Supplying & erecting resin bonded flap rock wool / glass

wool with conductivity valve 1.67 sq.mm per watt & to

with stand the temp. to 100 degree centigrade C

thickness 50mm with G I pipe of following size dia "B"

7 class as per IS:1239. The plastic sheet to be used as

covering of glass wool. Al. cladding besides other

materials like chicken mesh, 26 G Al. Sheet shall be used

for cladding the insulation pipe.

(A) for 20 mm dia pipe Mtr 30.00 360.00

(B) For 25 mm dia pipe Mtr 20.00 440.00

(C) for 32 mm dia pipe Mtr 20.00 530.00

(D) for 40 mm dia pipe Mtr 45.00 620.00

(E) for 50 mm dia pipe Mtr 6.00 760.00

Providing and fixing Gun metal check or non-return

8 fullway wheel valve.(C) 20mm dia. Each 15.00 276.00

Providing and fixing Gun metal check or non-return

9 fullway wheel valve.(C) 25mm dia. Each 15.00 457.00

Providing and fixing Gun metal check or non-return

10 fullway wheel valve.(E) 40mm dia. Each 15.00 584.00

Providing and fixing Gun metal check or non-return

11 fullway wheel valve.(E) 50mm dia. Each 20.00 821.00

Providing and supplying C.I. Air valves of approved

make & quality of following class and diameter

including taxes, insurance, transportation, freight

12 charges, octroi, inspection charges, loading, unloading, Each 15.00 661.00

conveyance to departmental stores, stacking etc.

complete. Air Valves single (S2) Type 25mm

Providing and fixing mosquito proof stainless steel

13 overflow grating for tanks.(// Each 6.00 2000.00

Audco/Lehry/ R.B./ Spirex) 100mm dia.

Consruction of Valves chambers in brick or bela stone

masonry, locally available in C.M. 1:6 foundation

concrete 150mm thick in CC 1:4:8 of trap metal size

25mm to 40mm thick, inside cement plaster in CM 1:3

and cement pointing outside in C.M. 1:3 and top cover of

precast RCC slab 100mm thick with key hole in two

parts, each with handles or MS Bar etc. complete as

given size) Upto 1 Mt. depth from G.L. to pipe invert

level incl. complete civil works but excl. cost of

excavation and refilling with cast in situ RCC slab in one

single piece with fixing of CI-MH Frame and cover (excl

cost of CI-MH Frame and cover) with 23mm thick brick

masonry wall in CM 1:6 (d) size of chamber 0.60 m x

0.60m and 1.0mt deep with precast slab in two parts

15mm with single piece 10cm with fixing MH Cover.

Supply, installation, Testing and Commissioning of

15mm Nominal diameter Garden Hydrant with gun

15 metal Ball Valve, GI pipe for Flexible hose Connection Each 10.00 2000.00

all required accessories etc.

Providing erecting and fixing double coated Syntex

PVC. (ISI) water tank of required capacity each with all

necessary fittings and connection etc. complete on

Supplying and erecting chromium plated heavy duty

17 brass valve for inlet pipe of water heater 15 mm dia.) Nos 30.00 180.00

Supplying and erecting 15mm brass non-return valve

18 for inlet pipe of storage water heater. Nos 30.00 230.00

Supplying and erecting dead pressure releasing valve

19 for storage type water heater with necessary materials. Nos 20.00 380.00

Providing & erecting fibre reinforced PVC flexible pipe

20 with brass locking nuts & washers & clips at both ends Nos 10.00 180.00

complete erected without leakage

INTERNAL SWR SYSTEM

Providing and fixing to wall ceiling and floor 10.0 Kg.

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

21 special falnge compression type fittings, wall clipsetc. Rmt 500.00 100.49

including making good the wall ceiling and floor.(C)

Providing and fixing to wall ceiling and floor 10.0 Kg.

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

22 special falnge compression type fittings, wall clipsetc. Rmt 600.00 116.40

including making good the wall ceiling and floor.(D)

Providing and fixing to wall ceiling and floor 10.0 Kg.

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

23 special falnge compression type fittings, wall clipsetc. Rmt 350.00 124.43

including making good the wall ceiling and floor.(E)

Providing and fixing to wall ceiling and floor 10.0 Kg.

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

24 special falnge compression type fittings, wall clipsetc. Rmt 600.00 332.91

including making good the wall ceiling and floor.(G)110

Providing and fixing to wall ceiling and floor 10.0 Kg.

F/Cm2 working pressure polythene pipes of the

following outside Dia. Low densidy, complete with

25 special falnge compression type fittings, wall clipsetc. Rmt 500.00 274.68

including making good the wall ceiling and floor.(F)

Providing and fixing PVC SWR Nahni trap IS 14735 for

drain - 100 mm diameter with jali of the following

26 nominal diameter of self cleansing design with C.I each 40.00 565.43

scread down or hinged grating including the cost of

cutting and making good the walls.

Providing and fixing PVC SWR Nahni trap IS 14735 for

drain - 75 mm diameter with jali of the following

27 nominal diameter of self cleansing design with C.I each 40.00 552.83

scread down or hinged grating including the cost of

cutting and making good the walls.

EXTERNAL SWR SYSTEM

Providing and fixing S.W. gully trap with C.I. grating

brick masonry chamber and water tight C.I. cover with

28 frame of 300mm x 300mm size (inside) with standard Each 40.00 1279.40

weight.(i) Square mouth traps. (A) 100mm x 100mm

size P type. (upto 10 ton)

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

Sewerage & Drainage application as per EN:13476-3

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 100mm

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

30 Sewerage & Drainage application as per EN:13476-3 Rmt 100.00 373.00

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 150mm

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

31 Sewerage & Drainage application as per EN:13476-3 Rmt 100.00 738.00

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 200mm

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

32 Sewerage & Drainage application as per EN:13476-3 Rmt 100.00 1004.00

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 250mm

Constructing Manhole with R.C.C. top slab in 1:2:4 mix

(1-cement :2-coarse sand : 4-graded stone aggregate

20mm nominal size) foundation concrete 1:3:6 mix (1-

cement : 3- coarse sand :6-Brick bats 40 + 50mm size)

inside plastering 15mm thick with Cement Mortar 1:5

(1-Cement : 5-coarse sand) finished with a floating coat

of neat cement and making channels in cement concrete

1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate

20mm nominal size) finished smooth complete

33 including curing and festing (i) Inside size 900mm x Each 2.00 10920.76

1200mm and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and frame to

be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of

frame 64 Kg.)(A) With 230mm thick walls of brick

msonry using brick having crushing strength not less

than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement:

5-Coarse sand) (1) A type depth 0.90 Metre for

150mm diameter sewer.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix

(1-cement :2-coarse sand : 4-graded stone aggregate

20mm nominal size) foundation concrete 1:3:6 mix (1-

cement : 3- coarse sand :6-Brick bats 40 + 50mm size)

inside plastering 15mm thick with Cement Mortar 1:5

(1-Cement : 5-coarse sand) finished with a floating coat

of neat cement and making channels in cement concrete

1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate

20mm nominal size) finished smooth complete

34 including curing and festing (i) Inside size 900mm x Each 2.00 19139.07

1200mm and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and frame to

be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of

frame 64 Kg.)(A) With 230mm thick walls of brick

msonry using brick having crushing strength not less

than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement:

5-Coarse sand) (2) B type depth 1.50 Metre for

150mm diameter sewer.

Providing and laying Cement concrete 1:5:10 (1-

Cement : 5-Fine sand :10-Graded stone aggregate 40mm

nominal size) bedding for stoneware pipes of following

35 internal diameters with necessary formwork and curing Rmt 80.00 211.59

complete.(B) 150mm dia. (166mm Ave. bed thickness)

Constructing brick masonry chamber for underground

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

36 frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement Each 2.00 2903.89

:2- coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line. (upto 10 ton)

Providing and fixing G.I. Rain water spout of 50mm dia.

37 and 30cm. length. Each 50.00 100.90

Constructing Brick masonry road gully chamber

500mm x 450mm x 600mm including 500mm x 450mm

C.I. horizontal grating wih frame complete.(upto 10 ton)

Constructing brick masonry road gully chamber

1100mm x 775mm including 500mm x 450mm (C.I.

39 horizontal grating with frame and vertical grating No. 2.00 1997.20

complete.) (upto 10 ton)

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

40 Sewerage & Drainage application as per EN:13476-3 Rmt 50.00 208.00

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 100mm

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

41 Sewerage & Drainage application as per EN:13476-3 Rmt 80.00 373.00

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 150mm

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

42 Sewerage & Drainage application as per EN:13476-3 Rmt 75.00 738.00

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 200mm

Providing & Supplying of Class SN8 structured wall

Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth

External Annular corrugated and smooth internal

surfaces (Double Wall) for non pressure underground

43 Sewerage & Drainage application as per EN:13476-3 Rmt 60.00 1004.00

incuding all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc.

complete (ID Dia). Pipe Dia. ID 250mm

Providing and laying Cement concrete 1:5:10 (1-

Cement : 5-Fine sand :10-Graded stone aggregate 40mm

nominal size) bedding for stoneware pipes of following

44 internal diameters with necessary formwork and curing Rmt 100.00 211.59

complete.(B) 150mm dia. (166mm Ave. bed thickness)

TOILET FIXTURES

Providing and fixing wash down water closet (European

type, W.C. Pan) with integral P or S trap including

jointing the trap with soil pipe in Cement Mortar 1:1 (1-

45 Cement : 1-fine sand) (Seal and cover to be measured Each 6.00 1290.80

and paid for separately) (A) vitreous China Pattern :(i)

in white colour

Providing and fixing 12.5 Litres low level flushing

cistern with a pair, of C.I. or Mild brackets, complete

with fittings such as lead valve less syphon, 15mm

nom.nal size brass ball valve with polythene float, C.P

brass handle unions and couplings for connections, with

46 inlet, outlet and overflow pipes, 40mm dia. porcelain Each 6.00 2321.21

enamelled flush bend including cutting holes in walls

and making good the same connecting the flush bend

with cistern and closet (overflow pipe to be measured

and paid for separately)(A) Vitreous China (I) In white

Providing and fixing plastic seat and cover for wash

down water closer with C.P. brass hinges and rubber

buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for

pillar tap with C.I. or M.S. brackets painted white

including sutting holes and making good the same but

excluding fittings.(A) Vitreous China:(ii) Flat Back

washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S.

brackets, painted white including cutting holes in walls

and making good the same but excluding fittings. (C) Each 4.00 2257.69

Vitreous China Sink.(i) 600mm x 450mmx 150mm size

Providing and fixing C.P. brass waste for washbasin or

49 sink. (B) 40mm dia. Each 7.00 88.94

Providing and fixing M.I. fisher union for washbasin or

50 sink. (B) 40mm dia. Each 7.00 87.77

Providing and fixing 100mm sand cast iron grating for

51 gully, floor or Nahni trap. Each 30.00 36.61

Providing and fixing 600mm x 450mm bevelled edge

mirrror of superior glass mounted on 6mm thick A.C.

52 sheet or plywood sheet and fixing to wooden pluge with Each 10.00 825.48

C.P. brass screws and washers.

Providing and fixing 600mm x 120mm glass shelf with

53 C.P. brass bracket and guard rail complete mixed to Each 7.00 561.03

wooden plug with C.P. brass screws.

54 Providing and fixing toilet paper holder.(A) C.P. Brass Each 7.00 414.53

Providing and fixing screw down bib taps of following

55 size.(B) Brass chromium plated screws down Bib Tap. Each 14.00 212.68

Providing and fixing pillar tap, capstan head, screw

56 down high pressure with screws, shanks and back nuts. Each 14.00 305.67

Providing and fixing chromium plated brass half trun

57 flush cock of approved quality including fixing in pipe Each 6.00 252.26

line etc. complete.(i) 20mm dia.

Providing and fixing chromium plated brass half trun

flush cock of approved quality including fixing in pipe

line etc. complete.(ii) 25mm dia.

Providing and fixing Urinal or approved quality

including conecting the Urinal with waste pipe , tap etc.

59 complete.(A) White earthenware flat back or corner Each 6.00 1026.01

type size 430mm x 260mm x 350mm.

60 Providing and fixing Rubber plug for sink or wash basin. Each 15.00 16.98

Providing and fixing chromium plated, bottle trap with

61 necessary couplings of approved quality for wash basin. Each 10.00 292.87

Providing and fixing ball cock of approved. quality as

62 directed.(A) Copper Metal (ii) 50mm dia. Each 10.00 187.96

Providing and fixing Angle Cock with screw, back nuts

all necessary fittings etc. Completed

(Cera-CM108/ Parryware-T9939A1 / Hindware-

Providing and fixing water closet squatting Pan (Indian

type W.C. Pan) size 580mm (Earthwork, bed concrete,

64 foot reste and trap to be measured and paid for Each 1.00 926.10

separately) (A) Vitreous China. (1) Long pattern =

Providing and fixing 12mm dia. Health faucet with

mm dia of JAQUAR / HINDWARE/ CERA or approved

65 make selected by Architect with flexible pipe of 1mt. Each 10.00 1200.00

length and holding stands complete. Model Equivalant

to Jaquar- CAT - ALD-577.

Point wiring for Light / Bell with 2-1.5 sq.mm &

earthwire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper

wires, in following type of pipe to be erected concealed

in/ on surface on wall/ceiling complete with 6A

Modular type switch / bell push & accessories and earth

1 continuity of following type, erected on PVC / Metallic Pt 50.00 445.00

box, single mounting base frame covered with

textured/metallic front plate modules erected on / in

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (a)

with medium class Rigid PVC pipe and accessories CAT

Point wiring for secondary light point with 2-1.5 sq.mm

& earthwire of 1.5 sq.mm (green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper

wires, in following type of pipe to be erected concealed

in / flushed on wall/ceiling, complete with earth

2 continuity and necessary connection with primary light Pt 75.00 131.00

with accessories erected on Metal / PVC box covered

with 3 mm thick PC(Polycarbonet) / Acrylic sheet for

open / concealed wiring. with necessary Lamp holder /

ceiling rose / H.D.Connector as directed. (a) with

medium class Rigid PVC pipe and accessories

Point wiring for Two Way Controlled Light Point with 2-

1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of

.ISI marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of pipe to be

erected concealed in / flushed on wall/ceiling ,complete

3 with 6A Modular type switches and following type of Pt 10.00 562.00

accessories erected on PVC / Metallic box, single

mounting base frame covered with textured / metallic

front plate modules erected on / in wall / ceiling as per

pipe erected. with necessary batten/angle holder or

ceiling rose or H.D.Connector as directed CATIII

Point wiring for FAN with 2-1.5 sq.mm & earthwire of

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multistrand copper wires, in

following type of pipe to be erected concealed in /

flushed on wall/ceiling complete with 6A Modular type

switch and hum free EME four or more step type

electronic fan regulator with separately mounted and

accessories with earth continuity of following type

erected on PVC / Metallic box, single mounting base

frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as

directed. (a) with medium class Rigid PVC pipe and

accessories.CAT III

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

5 metallic/white front plate , modules erected with Ea 20.00 676.00

necessary connections as per site situation directed by

Engineer In charge. (23)USB Charger with output of 5 V

DC,2.1 A with inbuilt surge protection. Cat-III

Point wiring for Looped Plug with 6A Modular type

switch & 5 pin socket erected on PVC / Metallic box,

6 single mounting base frame covered with textured / Nos 35.00 255.00

metallic front plate modules erected on / in wall /

ceiling with following type accessories. CAT III

Point wiring for Individual Plug with & earthwire of

sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multistrand copper wires, in

following type of to be erected concealed in / on surface

of wall / ceiling complete with Modular type switch &

7 pin Plug erected on PVC / Metallic box covered with Pt 25.00 471.00

appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of

accessories. For 6A Plug with 2-1.5 sq.mm Cu. Wire with

medium class Rigid PVC pipe and accessories CAT III

Point wiring for Individual Plug with & earthwire of

sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multistrand copper wires, in

following type of to be erected concealed in / on surface

of wall / ceiling complete with Modular type switch &

8 pin Plug erected on PVC / Metallic box covered with Pt 30.00 704.00

appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of

accessories.[III] For 16A Plug with 2-2.5 sq.mm Cu. Wire

(a) with medium class Rigid PVC pipe and

accessories.CAT-III

Providing & erecting Switch board for Computer or

electric apparatus consisting of following items in

single board erected on PVC / Metal board with 3 mm

9 thick PC (Polycarbonate) / Acrylic sheet erected as Ea 5.00 1122.00

directed for [B] modular type accessories

1 no. 6A/16A universal plug-switch combined. CATIII

nos. 6A Switch 3 nos. 6A 5 pin Plug

MAINS WIRING AND CONDUIT

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on

10 wall/ceiling, with 1.5 sq. mm copper conductor FRLS Mtr 2500.00 62.00

PVC insulated stranded wire of green colour for earth

continuity of following size (a) with medium class Rigid

PVC pipe and accessories (a) 2 wire 1.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on

11 wall/ceiling, with 1.5 sq. mm copper conductor FRLS Mtr 1500.06 82.00

PVC insulated stranded wire of green colour for earth

continuity of following size (a) with medium class Rigid

PVC pipe and accessories (B) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of

pipe to be erected in / on wall / ceiling with 2.5 sq. mm

12 copper conductor FRLS PVC insulated stranded wire of Mtr 1232.00 111.00

green colour for earth continuity of following size. (a)

with medium class Rigid PVC pipe and accessories

(A) 2 wire 4 sq. mm

FANS & EXHAUST FAN ACCESSORIES

Providing & erecting Approved make Power Saving

Watt Ceiling Fan with double ball bearing ISI mark with

Condenser 230 volt A.C. 50 Hz 1200 mm sweep

13 complete having 3blades with aluminium blades with , Nos 12.00 1929.00

canopy & 30 cm. down rod erected with earthing.(Make

shall be approved by Engineer in charge))

Providing 2.5mm.thick laminated acrylic sheet to cover

14 the fan hook or Fan box. Nos 12.00 18.00

Supplying and erecting 19 / 20 mm. nominal bore

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with necessary 24/ O.20, 3 core flexible

wire with earthing.

Supplying & erecting fan hook box of 10 mm M.S. round

bar bounded to the RCC bars up to 50mm length each

16 side and pierced through a 16 Gauge M.S. box / Heavy Nos 12.00 107.00

Duty PVC box complete erected concealed in Ceiling

with necessary finishing.

Supplying & erecting approved make low noise

decorative Exhaust fan having size 200mm with

RPM with square frame ABS body with inbuilt lowers &

LIGHTING FIXTURES :

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than

0.95, THD < 15%, CCT 3000 K to 6500K, Luminaire

18 efficacy> 85 lumens/watt ,LED LED driver efficiency > EA 30.00 370.00

85 % ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the

ranges shown.). (A) Tube Light with integral driver. (iv)

22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet. Cat-

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company

19 mark/name 160V to 270V,Power Factor more than Ea. 30.00 584.00

0.95, THD < 15 %, CCT 3000 K to 6500K, Luminaire

efficacy> 85 lumens/watt , LED driver efficiency >

%( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges

shown.). (iii) 16-20 watts, Surge-2 KV Cat-lll

Supplying and erecting led lamps with following

20 wattage capacity of 220 to 240 voltage, minimum 15000 Ea. 5.00 187.00

burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable

for E14 / E27 / B22 lamp holders, pf >= 0.5. (A) LED

Lamps integral type, with PC diffuser suitable LAMP

holder. (iii) 10 to 15 watts. Cat-III

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company

21 mark/name 160V to 270V,Power Factor more than

0.95, THD < 15 %, CCT 3000 K to 6500K, Luminaire

efficacy> 85 lumens/watt , LED driver efficiency >

%( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

(G) Step Light having Aluminium die cast and ABS

Plastic material.

(i) 5 watts, Direct/Indirect luminaire - cat-iii Ea. 20.00 568.00

(H) Mirror Light 9 Watts, wall mounted minimum 1 feet

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die

cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed

to 270 V,Power Factor more than 0.95, THD < 10 %, CCT

22 3000 K to 5700K,Uniformity ratio >0.45, Luminaire Ea. 2.00 7195.00

efficacy> 100 lumens/watt . LED driver efficiency >

%.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the

ranges shown.). (B) Flood Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC

line supply with over-voltage protection. (iv) above

to 120 watts. Cat-lll

DISTRIBUTION BOXES

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, confirming

23 to IS 13032 and BS 5486-1986 without MCB to house Each 3.00 1141.00

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used)

(F) Single phase 8 way SS Double door

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

24 appropriate nos. of MCBs.(The DBs should be used of Each 1.00 1478.00

same company of MCB to be used) suitable for. (A)

single phase incoming and horizontal single phase

outgoing. (iv)Single phase 12 way SS Double door

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, confirming

25 to IS 13032 and BS 5486-1986 without MCB to house Ea 2.00 2885.00

appropriate nos. of MCBs N) Three phase 6 way SS

Double door for horizontal single phase outgoing

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, confirming

to IS 13032 and BS 5486-1986 without MCB to house

appropriate nos. of MCBs N) Three phase 8 way SS

Double door for horizontal single phase outgoing

MINIATURE CIRCUIT BREAKER

providing and erecting Miniature circuit breaker single

pole 6A to 25A suitable to operate on 240 V A.C. system

27 and having breaking capacity 10 KA to be erected in EA 75.00 111.00

existing box. confirming to IS 8828/1996 with ISI Mark

Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking capacity

28 & confirms to IS : 8828 in existing box having following Ea 2.00 293.00

capacity (B) 40 Amp. Cat.III

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA

29 breaking capacity & confirms to IS : 8828 in existing box Ea 2.00 297.00

having following capacity (A) 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA

30 breaking capacity & confirms to IS : 8828 in existing box Ea 2.00 327.00

having following capacity (B) 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

31 capacity & confirms to IS :8828 in existing box having Ea 2.00 590.00

following capacity (a) 6 to 32 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

32 capacity & confirms to IS :8828 in existing box having Ea 2.00 662.00

following capacity (b)40 Amp. Cat.III

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking capacity

33 & confirms to IS :8828 in existing box having following Ea 2.00 632.00

capacity (b)40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

34 capacity & confirms to IS :8828 in existing box having Ea 2.00 730.00

following capacity

C) 63 Amp. CAT-III

Approved make ELCBs / RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit

withstand capacity of 6 KA and suitable for operation on

35 single phase 240 V. having characteristic of quick action Ea 5.00 1950.00

& tripping with all advance feature & do not incorporate

any electronic component. for following Max. rating

erected as directed (i) 25 Amps.DP Cat. III

Approved make ELCBs / RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit

withstand capacity of 6 KA and suitable for operation on

36 single phase 240 V. having characteristic of quick action Ea 2.00 2213.00

& tripping with all advance feature & do not incorporate

any electronic component. for following Max. rating

erected as directed (i) 40 Amps.DP Cat. III

Approved make ELCBs / RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit

withstand capacity of 6 KA and suitable for operation on

37 single phase 240 V. having characteristic of quick action Ea 2.00 2628.00

& tripping with all advance feature & do not incorporate

any electronic component. for following Max. rating

erected as directed (i) 63 Amps.DP Cat. III

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor for

38 1.1 KV. to be laid on wall with necessary clamps or in Mtr 300.00 218.00

existing trench / pipe of following size of cables (B)

1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor for

39 1.1 KV. to be laid on wall with necessary clamps or in Mtr 300.00 182.00

existing trench / pipe of following size of cables. (A)

1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor for

40 1.1 KV. to be laid on wall with necessary clamps or in Mtr 300.00 152.00

existing trench / pipe of following size of cables. A)4

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Copper conductor

41 for 1.1 KV. to be laid on wall with necessary clamps or Mtr 100.00 361.00

in existing trench / pipe at road crossing or floor of

following size of cables. (C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Copper conductor for

42 KV. to be laid on wall with necessary clamps or in Mtr 1000.00 670.00

existing trench / pipe at road crossing or floor of

following size of cables. (A) 4 core 10 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Copper conductor for

43 KV. to be laid on wall with necessary clamps or in MTR 1500.00 392.00

existing trench / pipe at road crossing or floor of

following size of cable. (C) 3 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass

double compression type cable gland with rubber ring

44 for PVC insulated armoured cable complete with out EA 10.00 75.00

going tails, insulating tape etc for following size of

cables. (B) 3 & 1/2 core 35/50 Sq. mm

Providing and fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured

45 cable complete with out going tails, insulating tape etc EA 10.00 51.00

for following size of cables.

E) 2 to 4 core 25 Sq. mm

Providing and fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured

46 cable complete with out going tails, insulating tape etc Ea 10.00 47.00

for following size of cables.

D) 2 to 4 core 16 Sq. mm

Providing and fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured

47 cable complete with out going tails, insulating tape etc Ea 150.00 38.00

for following size of cables.

(B) 2 to 4 core 6 Sq. mm

Providing and fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured

48 cable complete with out going tails, insulating tape etc Ea 20.00 38.00

for following size of cables.

C) 2 to 4 core 10 Sq. mm

Solder less crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped

49 with high pressure tool & connected to switchgear Ea 15.00 98.00

terminals with brass/cadmium plated nut bolts in an

approved manner. (K) 300 Sq.mm.

Solder less crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped

50 with high pressure tool & connected to switchgear Ea 20.00 61.00

terminals with brass/cadmium plated nut bolts in an

approved manner. (H) 150 Sq.mm. .

Solder less crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped

51 with high pressure tool & connected to switchgear Ea 40.00 20.00

terminals with brass/cadmium plated nut bolts in an

approved manner. (D) 35/50 Sq.mm.

Solderless crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

52 terminals with brass/cadmium plated nut bolts in an Ea 40.00 15.00

approved manner.

Solderless crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

53 terminals with brass/cadmium plated nut bolts in an Ea 80.00 13.00

approved manner.

Solder less crimping type Copper lugs conforming to IS

suitable for cable of following size evenly crimped with

54 high pressure tool & connected to switchgear terminals Ea 450.00 8.00

with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5/2.5 to 6 Sq.mm

Providing and erecting Annealed bare Copper wire 8 to

Providing and erecting HOT deep Galvanised iron strip

56 wire 8 to 16 SWG. KG 150.00 77.00

Providing and erecting required size HOT deep

Galvanised iron strip for earthing of H.T. , OCB/ ACB/

Transformer LT panel board, Motors etc. using proper

Providing and erecting required size Copper strip for

58 earthing of H.T. OCB / ACB/ Transformer, LT panel KG 40.00 787.00

board, Motors etc. using copper clamp.

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250

59 Micron galvanising, connection terminal dia of 14 mm

with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with

chamber and heavy duty cover.(approved make OEM

has to submit test certificate including value of earth

resistane of installation.

[B] For Electrical installation up to 11 KV located in

other than normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr Ea 2.00 7025.00

-Back filling Compound :1 no. Bag of 25 Kg.

(c) For Electrical Installation covering Transformer

Neutrals, Lightning arrester Earthing, A.C.Plant &

Sensitive Computer System(like Automation, SCADA)

i.e independent Earthing in normal soil.

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

SITC of 14.2 mm dia 3 mtr long Earth electrode of High

tensile steel electrode with 250 micron copper bonding

& 1 bag of Carbon fill Based environment friendly

backfill tested as per IEC 62561-7 in NABL accredited

60 Laboratory and suitable stainless Steel double sided Ea 2.00 5933.00

clamp. Eco Friendly rust proof heavy duty weather

proof Polyethylene Earth Pit Chamber with following

dimensions :254 mm dia (top), 330 mm dia (bottom) &

260 mm (height).

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC fittings

61 & Junction boxes fixed with adhesive solution & Clamps Mtr. 1500.00 32.00

with following dia of pipes, in approved manner as

directed (b) 25 mm

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC fittings

62 & Junction boxes fixed with adhesive solution & Clamps Mtr. 200.00 52.00

with following dia of pipes, in approved manner as

directed (c) 32 mm

Providing & erecting weather proof, dust & vermin

proof, floor mounted front operated indoor type cubical

panel board necessary IP-42 and above protection as

per approval from engineer incharge made from

SWG thick CRC M.S. sheet for outer body & doors,

SWG thick CRC M.S.sheet for internal partitions with

necessary accesories , supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable

size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite

control fuses/MCB for measuring instruments, earth

63 bus & earth bolts, foundation flange - bolts-base Plates, Sq.Mtr 5.00 19196.00

sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating. (The rates excludes

the cost of switchgears, bus bars, inter connecting mains

& Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams)

The panel shall be supplied with following approved

manufacturers with following size.(B) The standard

companies switch gear shall be used and only

manufacturers at CPRI approved factory. (ii) With

Providing , erecting , fabricating the M.S. structure as

per requirement on site incorporating proper size of

M.S. angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing

64 duly painted with one coat of red oxide with erection on kG 350.00 77.00

site as per direction of engineer in charge with

necessary grouting, cementing, plastering & finishing

Supplying and erecting triple pole & neutral 440V/

500V panel mounting Aluminium Busbars with four

equal Nos. of bus having current density not more than

0.8 Amp. / sq.mm (Rated current / cross section area)

duly wrapped with colour insulating tape for phase

sequence of following current carrying capacity, erected

with necessary bus bar supports /insulators, main cable

socket to each busbar,erected in existing cubical panel

with necessary connections. (C) Suitable for 300 Amp.

(A) Suitable for 100 Amp. Capacity Rn.Mtr 10.00 654.00

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking capacity

ICU of 35 KA. and above at 415 V . having normal

current rating 250A. with variable thermal & magnetic

66 release suitable to work on A.C.supply 50 c/s. with all Ea 1.00 20739.00

internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. . ICS=100% of

ICU only Cat III

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking capacity

ICU of 35 KA. at 415 V. having normal current rating

125A. with Fixed thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing

16 G.M.S. housing.. . ICS=100% of ICU only Cat

Supplying and erecting led lamps with following

wattage capacity of 220 to 240 voltage, minimum

69 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable

for E14 / E27 / B22 lamp holders, pf >=

(A) LED Lamps integral type, with PC diffuser suitable

LAMP holder Ea 6.00 111.00

(ii) 5 to 8 watts

70 Operational Handle Assembly Complete for

71 Cable Terminal ( ‘Plain" Type)Set of Four for

Supplying & erecting power contactor ,AC3 duty for

72 time switch complete erected as per direction Cat III

Supplying & erecting approved make Digital time switch

having lithium cell 6 years operative and operate

battery backup 1 channel day clock with 14 memory

programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time

73 minimum & LCD display. Also comprised permanent Ea. 2.00 3137.00

ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover

erected as required with necessary connection erected

Providing and erecting Approved make Earth fault

Relay suitable to mount with inter connection suitable

to following size of moulded case circuit breaker having

74 CT ratio & MCCB rating as following along with shunt

trip 220V AC. with all internal connections & complete

erected in existing M.S.housing..

Providing & erecting Medium Voltage Danger Notice

Board sticker as per language suggested by engineer

incharge of standard size as per IS-2551

providing and erecting Mains with ISI marked, 1.5KV

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

76 to IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(b) One wire 1.50 sq. mm Mtr. 25.00 17.00

(c) One wire 2.50 sq. mm Mtr. 25.00 27.00

providng and erecting Suitable set of CTS for 100A

78 INDICATOR LAMP Ea. 3.00 113.80

79 TOGGLE SWITCH Ea. 3.00 115.00

80 THERMOSTATE HEATER Ea. 3.00 100.00

Providing and erecting multifunctional meter suitable

for application of Power monitoring and showing

measurement of following Voltage, Frequency,

Apparent energy, Apparent power, Active and reactive

energy, Active and reactive power, Average voltage

Vavg, Peak demand power PM, QM, SM, Demand power

P, Q, S, Apparent power S, S1, S2, S3, Unbalance current,

Power factor and displacement PF (signed, four

quadrant), Calculated neutral current, Active, reactive,

81 apparent energy (signed, four quadrant), Active power Ea. 1.00 13984.00

P, P1, P2, P3, Voltage U21, U32, U13, V1, V2, V3, Phase

currents, Average current Iag, Peak demand currents,

Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3,

[Us] rated supply voltage 40...300 V AC 45...65 Hz,

40...300 V DC, Network frequency 50 Hz, Type of

network 3P, Display type 7 segments LED, Display

colour Red, Messages display capacity 3 fields of

characters, Display digits 12 digit(s) - 14.2 mm in height

Supplying rubber matting of following thickness as per

82 IS:15652/IEC

providng and erecting Approved make energy meter

phase 4 wire unbalanced load rating, 10A to 60 Amp.

based on ASIC(Application specific Integral Circuits)

digital technology with accuracy Class - 1 , temper proof,

83 free from effect of external magnetic field with 3 phase S.Mtr 1.00 2670.00

indication, earth & impulse indication, 6 digit electro

mechanical impulse counter, suitable work on 120 V to

300V per phase 45-55 HZ, housed in robust enclosure

with erection as directed.

STREET LIGHT AND EXTERNAL

Supply of approved make FRP Pole having following

specifications: FRP Light Pole made by CNC filament

winding machine using thermoset resin

polyester/epoxy resin system) having minimum 62%

glass content. The pole should be in one piece and

84 tapered round in shape, having smooth finish and

should be totally free from corrosion as well as non

conductive & shock proof Pole should be provided with

FRP Anchor Base and it should be heavy duty, or MS

Material duly painted with Epoxy paint.

Pole should be flame retardant as per IS 6746. Resin

used shall be UV resistance and pigmented. A highly

weather resistant polyurethane coating shall be applied

to the pole after applying suitable primer system that

ensures proper adhesion of the paint. Minimum coating

thickness shall be 80 to 100 micron. Deflection of the

pole shall not exceed more than 10% of the length of

85 pole for the given load“ Pole should be generally made

as per the dimensional data, performance criteria and

some interchangeability features of poles as per

standard ANSI C 136.20 latest version or ASTM D

4923/01 including cable termination box with

necessary accessories . The size of pole and type of

installation with foundation as per manufacturer details

and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[H] Overall length of 6 Mtr. Average Thickness: 7.5mm

Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx.

Weight of Pole 32 kg approx. (Without Base) Anchor

Base (Size 300X300 & 18mm Th.)

(2) Suitable for base plate mounting Double arm

[C] Overall length of 6 Mtr. Average Thickness: 8mm.

Top/ Bottom OD Dia A/F 114/174 mm ± 2mm approx.

approx. Weight of Pole 38 kg approx. (Without Base)

Anchor Base (Size 300X300 & 18mm th.)

Providing 1:2:4 cement concrete foundation & 70 %

PCC from bottom including excavation for the pole of

size 45 x 45 x 100 cm. Deep in below ground level with

86 plinth of 45 cm x 45 cm (or 45 cm dia x 45 cm) high Ea. 60.00 801.00

upper ground level with necessary curing and finishing

in approved manner.

( for 4 & 6 mtr pole)

Providing cement concrete.for foundation or for

concrete filling in 1:2:4 ratio with 20 to 25 mm stone

metal duly plastered with necessary curing for pole

muffing or any other purpose.

Providing FRP/GRP arm bracket of having 15˚ arm with

88 50 mm OD pipe *5 mm thk,1000mm long from pole

(A) Single arm bracket Ea. 60.00 1882.00

(B) Double arm bracket Ea. 5.00 2390.00

Supplying & erecting approved make IP 55 grade

Company fabricated Timer Panel of following capacity

for switch On-Off street lights on time scheduling basis

made from 16G CRCA sheet duly epoxy power painted

inside and outside with hinged doors and locking

89 arrangement consisting of suitable size of 4 Pole MCB

and 4 pole contactor (cat-III)with analog time switch,

auto manual switch of same make and suitable input

and output Bakelite terminals and with door earthing

approved by Engineer in charge.

Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming to

IS 14930 II )with necessary connecting accessories of

90 same material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable

(A)50 mm outer dia Mtr. 1000.00 62.00

(B)63mm outer dia Mtr. 500.00 73.00

Providing & laying. R.C.C. Hume pipe for cable to be laid

90 cm. below ground across the road crossing or on

floor with necessary material in an approved manner

and making the ground as per original.(C) 300 mm dia

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die

cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed

to 270 V,Power Factor more than 0.95, THD < 10 %, CCT

92 3000 K to 5700K,Uniformity ratio >0.45, Luminaire Each 70.00 5917.00

efficacy> 100 lumens/watt . LED driver efficiency >

%.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the

ranges shown.). (A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC

line supply with over-voltage protection. (iii) Above

Supplying and erecting Flexible PVC insulated multi

93 strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed.

(h) 2.50 Sq.mm 3 core round PVC sheathed Mtr 800.00 73.00

S.I.T.C. of single phase submersible pump set suitable

for 100 mm size or more dia bore well having motor

94 capacity and discharge as under with necessary panel

box. Lifting and Lowering taken extra.

(c) Motor rating 2 HP (17 stage) pump having capacity

of 106 LPM at 40 mtr head suitable for 32 mm dia. Ea. 2.00 18204.00

delivery pipe CAT-II

Providing and erecting ISI marked PVC insulated PVC

95 Sheathed Flat flexible Submersible copper cable Mtr 50.00 145.00

approved make of following Size. (C) 3 Core x 4 Sq. mm

Supplying & erecting ISI Marked (Embossed) following

size of “C” Class G.I . Pipe & erecting as directed by

Engineer-in-charge with necessary plumbing as

desired. (C) 40 mm dia

Supplying and erecting with leak proof materials, M.S.

Heavy duty ISI marked coupling having threads of

97 TPI/11 TPI suitable for ‘C’ class pipe to take load of Ea. 5.00 71.00

pump and pipe assembly of following size andTPI :- (A)

40mm( 1.5") dia. pipe 8 TPI

Supplying & erecting G.l. bend for pipe connections

98 suitable for (C) 40 mm (1.5") Ea. 3.00 94.00

Supplying & erecting ISI Marked G.l. Elbow for pipe

99 connections suitable for (C) 40 mm (1.5") Ea. 3.00 89.00

Supplying and erecting Direct On-line Electronics

Starter with 2-5/4-10/8-14/10-16 Amp. Rating relay

(variable current setting) directly operated in totally

insulated elegant enclosure and 18 Amp. Rating power

relay with start - stop button for single phase operation

up to 3 HP as per complete erected on P.W. Block with

following features.

Low voltage cut off below 140 V

High voltage cut off above 280 V

Overload protection

Indicating LEDs for motor on lv, hv & overload tripping.

Supplying & erecting approved make Automatic liquid

level controller 6A. with sensor testing as per

101 instruction of Engineer in charge on site complete with Ea. 1.00 2332.00

wiring connection with existing wires , with copper

conductor from pump to upper and lower tank.

LIASIONING WORK

FOR OBTAINING NOC

Power Liasoning Charges for obtaining N.O.C from

Electrical Inspector Statutory authority for Power/Ele.

102 Installation. Liasoning Charges shall include preparing Job 1.00 20000.00

required attested documents & drawing for obtaining

NOC/Test Report on behalf of client.

CCTV SYSTEM & ELV SYSTEM

Supply, Installation, testing & commisioning of 4MP Full

HD IR Network Bullet Camera. 1/3" 4MP PS CMOS

Image Sensor (0.9071 cm) • Max. 4MP (1920 ×

1080)@25/30fps • Instastream and Smart H.264+

103 dual-stream encoding • DWDR, Day/Night (ICR), 3D- Ea 8.00 9500.00

DNR, ROI, AWB, AGC, BLC, HLC • 3.6mm fixed lens

(2.8mm Optional) • IR Range of 40 Mtrs, IP67, PoE •

Mobile Software: iCMOB, gCMOB • CMS Software: KVMS

Pro Make : CP Plus or equivalent.

Supply, Installation, testing & commisioning of 4MP Full

HD IR Network Dome Camera. 1/3" 4MP PS CMOS

Image Sensor (0.9071 cm) • Max. 4MP (1920 ×

1080)@25/30fps • Instastream and Smart H.264+

104 dual-stream encoding • DWDR, Day/Night (ICR), 3D- Ea 2.00 11000.00

DNR, ROI, AWB, AGC, BLC, HLC • 3.6mm fixed lens

(2.8mm Optional) • IR Range of 40 Mtrs, IP67, PoE •

Mobile Software: iCMOB, gCMOB • CMS Software: KVMS

Pro Make : CP Plus or equivalent.

Supply, Installation, testing & commisioning of Up to

channel IP camera input, Max 384Mbps incoming

bandwidth, Instastream/H.265/Smart

H.264+/H.264/MJPEG, Up to 12MP resolution preview

and playback, Support 4 SATA HDDs up to 10TB Each,

RJ45-4,SFP-2, 2 HDMI / 2 VGA simultaneous video

output, Support Multi-brand network cameras, ONVIF

Version 2.4 conformance, Mobile Software: iCMOB,

gCMOB, CMS Software: KVMS Pro, with 1 nos of Western

Digital 10TB WD Purple Pro Surveillance Internal Hard

Drive HDD - eSATA,SAS,RS-232,RS-485. Hard drive shall

be sufficient for 30 days storage backup.Make : CP Plus

or equivalent, Model : CP-UNR-4K664R16-V2

Supplying & erecting approved make LAN cable of

following size in existing pipe as per direction [D] CAT -

6e ( For LAN, Telephone & Camera).

SITC of CAT6 UTP 24AWG PATCH CORD:2M,Plug 30U'

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

SITC of 8 x 10/100/1000BASE-T PoE ports, 4 x Gigabit

RJ45/SFP Combo ports

Advanced L2 switching and security features, L2+ Static

Routing, Optional “standard mode” or “surveillance

108 mode” management user interface Ea 1.00 18000.00

193 W PoE budget, [Approved by Competent Authority

i.e. not Below the rank of Executive Engineer ] complete

with outdoor type enclosure IP67 with Pole Mounting

Accessories complete.

SITC of 24 x 10/100/1000BASE-T PoE ports, 4 x Gigabit

RJ45/SFP Combo ports

Advanced L2 switching and security features, L2+ Static

109 Optional “standard mode” or “surveillance mode” Ea 1.00 31680.00

management user interface

193 W PoE budget, [Approved by Competent Authority

i.e. not Below the rank of Executive Engineer ]

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

Providing & Erecting Netwrok rack with following

capacity with Necessary cooling fan,Cable manager,6A

PDU,equipment rack with necessary mounting

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC fittings

& Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as

directed (b) 25 mm

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

113 metallic/white front plate , modules erected with Each 50.00 152.00

necessary connections as per site situation directed by

Engineer In charge. (4) TV Co-axial Socket outlet

Providing & Erecting approved make following size of

TV Co-axial flexible cable comprising inner conductor of

solid bare copper insulated with Foam PE & Secondary

114 conductor made of poly - Aluminium film bonded Al. Rmt 500.00 59.00

Braids @ suitable coverage overall sheathed with black

PVC insulation. (e) RG-11

Supply, installation, testing & Commissioning of 55 inch

UHD LED 4K Smart TV with all mounting accessories,

remote, Power unit complete. Min 2 USB Port, 2 HDMI

115 Port, VGA Port, Ethernet Port etc. with updated OS. Ea. 1.00 57500.00

2023 Latest Model, Make : Sony, Samsung, LG, Vu

TOTAL ELE WORKS WITH ELV WORKS

Providing, Fixing & Commissioning Fire exit signs of standard size

photoluminous type. (Auto glowing in dark type)

1 1) “Fire Hydrant” ( Size 100 x 300 mm or nearest) No. 4.00 505.00

2 (2) “Fire Hose Reel” ( Size 100 x 300 mm or nearest) No. 4.00 505.00

3 (3) “DCP Extinguisher” ( Size 100 x 200 mm or nearest) No. 4.00 353.50

4 (4) “CO2 Extinguisher” ( Size 100 x 200 mm or nearest) No. 4.00 353.50

(5) “Fire Exits / Emergency Exit” ( Size 100 x 300 mm

(6) “Fire alarm Manual call poin” ( Size 100 x 100 mm

Supplying & erecting carbon dioxide (CO2) fire

extinguisher user of following capacity with necessary

7 clamps made from 50 x 6 mm M.S. Flat with nut & bolts No. 4.00 6591.26

grouted in wall complete.[A] For 4.5 Kg Capacity

Supplying & erecting carbon dioxide (CO2) fire

extinguisher user of following capacity with necessary

8 clamps made from 50 x 6 mm M.S. Flat with nut & bolts No. 4.00 8671.86

grouted in wall complete.[B] For 5.5 / 6.5 KG Capacity

Supplying & erecting D.C.P. type fire extinguisher for

following capacity cartridge type with gun metal cap

150 gram CO2 gas cartridge, powder and brackets

9 confirming to IS 2171 1985 and complete erected with No. 2.00 1712.96

necessary clamps made from 50 x 6 mm M S Flat with

nuts and bolts grouted in wall complete.[A] For 4.5 Kg

Supplying & erecting D.C.P. type fire extinguisher for

following capacity cartridge type with gun metal cap

150 gram CO2 gas cartridge, powder and brackets

10 confirming to IS 2171 1985 and complete erected with No. 2.00 2226.04

necessary clamps made from 50 x 6 mm M S Flat with

nuts and bolts grouted in wall complete.

[B] For 10 KG Capacity

Supplying and erecting floor mounting stand for

keeping four nos. of FIRE buckets comprising 1500 mm

in length, 900 mm height frame made out of 30mm X30

11 mm X 4 mm angle iron with cross supports for legs, No. 1.00 942.33

welded with 4 hooks and duly painted with one coat of

red lead and two coats of approved enamelled silver

Supplying FIRE bucket round bottom of 9 litres

capacity made out of 24 gauge G.I. sheet with extra

12 handle at bottom duly painted white inside and Red out No. 4.00 214.12

side with FIRE mark, filled with dry-sand and kept on

existing stand provided or hung on wall hook.

Supplying, installation testing & commissioning of

approved quality (class-c) conforming to as per IS

such as tee, elbows, check nuts, flanger, nipples etc.,

including cutting welding, trending in ground including

excavation and providing cement concrete blocks as

13 support, anticorrosive treatment with coaltar / asphalt

tape as per IS 10221, refilling the trench etc. of following

sizes complete as required, etc...

Note : The piping installation has to be put to hydraulic

test to1.5 times Working pressure before applying

paint or pipe coating and wrapping etc. Complete.

(1) 150 mm diameter R.Mt. 45.00 2399.76

(2) 100 mm diameter R.Mt. 30.00 1868.50

Supplying, installation testing & commissioning of

approved quality (class-c) conforming to as per IS

/ IS 1239 such as tee, elbows, check nuts, flanger,

nipples etc., including cutting welding, trending fixing

on walls, ceiling (using 41- tech pip e/ M.S. Angle

supports work includes two coats of metal primer and

two coats of red enamel paint etc.,

Note : The piping installation has to be put to hydraulic

test to 1.5 times Working pressure before applying

paint or pipe coating and wrapping etc. Complete.

(1) 80 mm diameter R. Mt. 10.00 1133.22

(2) 100 mm diameter R. Mt. 40.00 1513.99

(3) 150 mm diameter R. Mt. 12.00 2084.64

(4) 200 mm diameter R. Mt. 0.00 2955.26

Fire Hydrant Landing Valve (Internal / External)

(Stainless Steel (SS-304) , ISI Marked): IS:

Supply, Installation and Testing of: Fire Hydrant

Landing Valve with necessary pipe fitments, hardware

15 and consumables. Nos. 4.00 6046.87

MOC:-Body: Stainless Steel (SS-304), Working Parts:

Stainless Steel (SS-304), Coupling: Stainless Steel (SS-

304) , Standard: -ISI Marked.

Size:-63 mm (Flange End: NB 75 mm, PCD 160 mm)

Fire Hose Pipe (Delivery Hose)- 63 mm x 15 m

Supply, Installation and Testing of: Fire Hose with Hose

Couplings. Stainless steel male and female coupling

bound and rivetted to hose pipes with copper rivets and

copper wire complete as required.

RRL (ISI Mark- Type A) Fire Hose.

Hose Couplings: ISI Marked Stainless Steel.

With SS Wire Binding.

Standard: - ISI Marked & TAC Approved Hose.

Size:-63 mm dia x 15m long Hose.

Providing, fixing, testing and commissioning of Wall

mounting swing type first aid Fire Hose Reel with drum,

17 hanging bracket, 30 M x 25 mm dia high pressure hose Nos. 4.00 12513.90

reel tubing as per IS:884 with shut nozzle and ball valve

and all required accessories.

Supply, Installation, Testing and Commissioning of

Weather proof Standard Fire Hose Cabinet wall

mounting type (750 mm x 600 mm x 250 mm deep)

18 having Double door opening with necessary locking No 4.00 4474.30

arrangement by allan key suitable for housing 2 no.x15

mtrs. hose pipe, 1no. Branch pipe& nozzle spanner. Duly

synthetic enamel painted.

Fire Hose Nozzle- Short Branch Pipe Nozzle.

Supply, Installation and Testing of: Short Branch-pipe

MOC: Stainless Steel (SS-304).

19 Standard: ISI Marked, Heavy Quality. IS : 903, suitable Nos. 4.00 1664.48

for 10 Kg / sq.cm operating pressure and suitable for

interconnections to hose pipe coupling as required.

Size:- 63 mm X 20 mm

Supplying and fixing specially designed gunmetal orifice

plates made out of 6 mm thick stainless steel (Grade

304) on hydrant outlets of landing valves including

20 distant pieces of suitable size for adjustment of delivery Nos. 4.00 1303.91

pressure of 3.5 kg/ sq.cm as required by LPA complete

with necessary companion flanges, nuts, bolts, gaskets

Providing, fixing, testing & commissioning of 15mm dia

quartzoid bulb type sprinklers of rating with required

21 accessories : Nos. 30.00 360.71

Pendent Sprinkler 57°C standard response (K-80) UL

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with

maximum working pressure of 175 PSI test pressure of

875 PSI (Burst) with branch line (Inlet) 25mm NPT

22 male thread to sprinkler head (Outlet) 15mm NPT Nos. 15.00 1243.56

female thread with reducer, nipple, 2 side

brackets,center bracket, stockbar of following sizes

complete as required etc of following sizes as required.

MAIN FIRE PUMP ROOM, TANK AND ACCESSORIES

Supplying & installing completely testing &

commissioning of centrifugal main fire pump (electrical

driven) for hydrant main / sprinkler main with cast iron

casing & bronze impeller & internal parts, make as

approved by ISO/CFO for fire duty, complete with

coupling, coupling guard necessary base frame,

foundation bolts, RCC foundation, antivibration paid

capable of discharging 2280 lt/min against 65 mtr. head

against all losses complete. The scope shall also include

electrical TEFC motor, operated on 3-ph, 440-V, 50 Hz,

2900 RPM Syn. speed with ‘B’ class winding, make as

approved by LFA. The pump shall be capable of giving

not less than 150% discharge at a head not less than

23 65% of the rated head. Motor to be of continuous rating Set 1.00 314867.50

Each incomer and Outgoing feeder should be capable for

protection against Overload, Short Circuit and Phase

reversal condition and shall be capable to communicate

with BMS . System should be capable to compensate for

frictional losses at lower flows. All alarms should be

displayed in the controller and BMS. System should be

equipped with dry running protection. Indication of all

type of faults / on-off status / electrical parameters shall

be available on panel and central IBMS monitors. On-off

operation for all pumps shall be available on BMS

Pump - Motor : Discharge : 2280 LPM, Head 65 mtr

Supply, installation, testing & commissioning of

centrifugal monoblock type fire booster pump with

suction &delivery pipe with motor having speed

24 RPM, 3 phase, AC, 50 Hz supply, incoming cable from Nos. 1.00 65902.50

fire panel to local operating station with end

terminations, earthing, base plate, antivibration paid

Starter Panel for Fire Booster Pump

Design, manufacture, supply ,installation, testing and

commissioning of star delta starter control panels

suitable for 415V, 3 phase, 4 wire, 50 hz power

distribution system . Control panel shall consists of 40A

Breaker , contactor, Over load relay and other require

components to finish satisfactory work. Control panel

should be communicate with pressure switch.

Necessasary integration between control panel and

pressure switch shall be part of scope. scope shall also

include all required accessories for dry run protection &

shall prevent the pump from dry running

All components in the control panel shall be as per type

2 coordination of respective OEM. (Fire Booster Pump

Panel). (Cost of wiring with pressure switches /

switching on and switching off the pumps locally and

remotely as per the drawing and as per local CFO

SITC of precharged air vessel (size 450mm dia x

mm height) with adequate pressure switches with

valves to operate as per operating sequence including

25 mm drain valve, air release valve with stop cock on

26 top, 25 mm inlet with isolation valve & the vessel shall Nos. 1.00 44036.00

be painted inside & outside. The tank shall be fabricated

from 8 mm thick MS plate with painting.

Air Vessel : 450 mm dia x 1500 mm h

Supplying & installing completely testing &

commissioning centrifugal main fire pump (diesel

driven) with cast iron casing & bronze or phosphor

bronze internal parts, make as approved by ISO/CFO for

fire duty, complete with coupling, coupling guard

necessary base frame, foundation bolts, RCC

foundation,antivibration paid , capable of discharging

2280 lt/min against 65 mtr. head against all losses

complete with suitable diesel engine of speed matching

the pump speed ,auto start facility with battery &

battery charger, necessary wiring, fuel tank ,exhaust

system, foundation gauges & wired for automatic start

of the water pump on drop of pressure in the hydrant

and sprinkler system. The pump should confirm to LFA

/ SEB & and IE Regulations. The pump shall be capable

of giving not less than 150% discharge at a head not less

than 65% of the rated head.

Pumping System shall be capable to communicate with

BMS . System should be capable to compensate for

frictional losses at lower flows. All alarms should be

displayed in the controller and BMS. Indication of on-off

status parameters shall be available on panel and

central IBMS monitors. On-off operation for all pumps

shall be available on BMS system.

Pump - Diesel Engine : Discharge : 2280 LPM, Head :

Supplying, installing, testing and commissioning of

Vetrical Centrifugal jockey pump -motor with discharge

180 lpm against 65 mtr. head with 3 phase, 415 V,

Hz motor having 2900 RPM, complete with coupling,

coupling guard necessary base frame, foundation bolts,

RCC foundation,antivibration paid , as per site

conditions and instructions of site engineer-in-charge

including proper fixing, The electrical motor for the

pump should comply as per Specification. The scope

shall also include necessary coupling, coupling guard,

base frame, foundation bolts, RCC foundation, etc.

28 complete. Nos. 1.00 142788.75

Each incomer and Outgoing feeder should be capable for

protection against Overload, Short Circuit and Phase

reversal condition and shall be capable to communicate

with BMS . System should be capable to compensate for

frictional losses at lower flows. All alarms should be

displayed in the controller and BMS. System should be

equipped with dry running protection. Indication of all

type of faults / on-off status / electrical parameters shall

be available on panel and central IBMS monitors. On-off

operation for all pumps shall be available on BMS

Supplying & erecting approved make 3 phase motor

control cubical panel ( Star - Delta) made from16 G.

CRCA sheet duly painted with epoxy powder painted

inside and outside with hinged doors and locking

arrangement, consisting of suitable size of ON- OFF

isolator (AC - 3/23 duty) main fuses, single phasing

preventer cum water level. Guard (Complete unit),

Toggle switch to by pass Single phase preventer cum

WLG, indicating lamps for R- Y- B phases, over load

relay, Automatic water level controller, Ammeter &

Voltmeter each with two way selector switch incoming

wires duly socket Crimped, Panel to be erected on angle

iron frame grouted on wall as directed. Star Delta &

main contactor, overload relay, thermal / Electronic

Star delta cutoff timer, start - stop push buttons. The

isolator overload relay & contactors of L& T, Siemens or

Cuttler Hamer make only. Panel to be erected on angle

iron frame ground on wall.(F) S / D up to 30 H.P.

SITC of electronic type water level indicator with LED

panel, with probe & all control wiring to operate the

system automatic/manual & shall prevent the pump

from dry running

Supply, Installation, Testing and Commissioning of

mm dia Glycerine filled Pressure Gauge of range 0 -

Kg / cm² conforming to IS - 3624 having bourdon tube

of stainless steel 310 in cast aluminium, stove enameled,

31 black, weather proof case with outer, screwed Nos. 1.00 7878.00

aluminium bezel and complete with necessary U-type

stainless steel siphon tube and cock including providing

suitably painted angle iron support to the tube etc.as

per specification complete as required.

Providing, fixing, testing and commissioning of Pressure

32 Switch with Needle Valve. Set 1.00 1523.08

Providing, fixing, testing and commissioning of 25 mm

33 dia Air Release Valve and Ball Valve assembly on top of Nos. 2.00 3425.92

each riser for Air release system.

Providing, fixing, testing and commissioning Pressure

34 Relieaf Valve 25mm dia with Ball Valve. No. 4.00 5888.30

Supplying, installing and commissioning C.I.flanged

pressure relief valve with CI body,suitable flanges, nuts,

bolts, gaskets etc. complete.

Supply, installation , testing comissioning of pressure

gauge of 0-21 kg/sq.cm range with 15 mm dia stop cock

valve,piping etc as required

Supplying, fixing, testing and commissioning of

butterfly valve of PN 1.6 rating with bronze / gunmetal

37 seat duly ISI marked complete with nuts, bolts, washers,

gaskets conforming to IS 13095 of following sizes as

Providing, installation, testing and commissioning of

non return valve of following sizes confirming to

IS:5312 complete with rubber gasket, GI bolts,

nuts,washers etc.as required :

a) 80 mm Dia Set 2.00 7614.39

Providing, installation, testing and commissioning of

stainless steel Y-strainer fabricated out of 1.6 mm thick

39 stainless steel, Grade 304, sheet with 3 mm dia holes No. 2.00 6514.50

with stainless steel flange.A) 100 mm Dia

Supplying and fixing of fire brigade connection of cast

iron body with gun metal male instantaneous inlet

40 couplings complete with cap and chain as reqd. for No. 1.00 6079.84

suitable dia MS pipe connection conforming to IS 904.

WAY / 4- WAY- 100 mm dia M.S. Pipe

SITC of fire brigade draw out connection with 100 mm

MS suction pipe & 100 mm dia foot valve. The scope

shall also include required valves, piping, M.S cabinet as

Supplying and erecting Flexible PVC insulated

42 multistrand multicore 1.1 kv grade ISI marked copper

wires of following size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed R. Mt. 145.00 44.44

f) 1.50 Sq.mm 4 core round PVC sheathed R. Mt. 195.35 64.64

Supplying, installation, testing & commissioning of

manual call boxes of MS construction in surface/recess

43 with stainless steel chain & hammer assembly complete No. 6.00 466.62

with glass and push button etc. as required.

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC fittings

44 & Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as

Supply, Installation, Testing and Commissioning of

Single action Manual Pull Station. Shock and Vibration

Resistant, pull Down Lever Remains Down Until Reset.

45 Shall be Polarity Insensitive (with all mounting No. 4.00 606.00

accessories , complete with Junction Box for mooting on

Surface, Cable lugs at Ends, cable compression glands,

cable tags and ferruling.

Supply, Installation, Testing and Commissioning of

Conventional Sounder / Hooter cum strobe having tone

settings with range of 95dbA and field selectable

46 15/30/75/110 candelas.(with all mounting accessories No. 4.00 606.00

, complete with Junction Box for mooting on surface,

cable lugs at ends, cable compression glands, cable tags

and Ferruling.)

Testing of Fire Fighting System, Preparation of Design &

Drawings Approval of Fire Hydrant & Entire Fire

Protection System from Local Fire Authority and any

other relevant statutory authority at initial (PRE- NOC /

OPINION) and POST CONSTRUCTION NOC or at various

other stages of work, including preparation of report /

drawings as per fire authority requirement. for pre

47 opinion lison charges to be given to indharge L.S. 1.00 75000.00

consultant. Contractor shall include cost of all liason

work which are not explicitly mentioned above but are

mandatory to have fire authority approval (any

statutory charges will be paid extra).

(Including Pre-NOC and Post Construction NOC from

Fire authority)

Providing and fixing, testing and commissioning of

48 conventional Smoke Detector. Nos. 24.00 1787.70

3M, or equivalent

Providing and fixing, testing and commissioning of

49 conventional Fire Alarm Panel 4 Zone Nos. 1.00 24431.90

Ravel/Agni/System Sensor, or equivalent

Supply and Commissioning of Fire Alarm Cable

50 SQMM,2 CORE, Copper Armored Cable Make : RR / R. Mt. 200.00 131.30

Provided Core Cutting in RCC beam /slab core cutter.

Provided Core Cutting in RCC beam /slab core cutter.

Provided Core Cutting in RCC beam /slab core cutter.

TOTAL FIREFIGHTING WORKS

LAYING OUT LAWN – After excavating soil upto

cm. depth & removing unwanted stuff, stones etc.

Preparing soil for planting by supplying and mixing

6 inch river fine site and 0.5 cmt FYM maximum

1 sqmt of lawn area and doing termicide @ 1 fit / 100 Sq.mt. 3718.00 85.00

sqmt area and planting selection 1 type / approved

lawn grass at maximum 6 cm x 6 cm distance and

maintain it upto 120 days. Maintainance include all

operations i.e. watering, grass cutting, gap filling,

applying of fertizer if require etc.

Supplying, Spreading and leveling of good earth like

2 firtile soil as directed etc compt. Cmt. 632.00 575.00

Supplying, Spreading and leveling of good quality river

3 Kap Filling 100 mm as directed etc comp. Cmt. 632.00 575.00

RAISING HEDGE : After excavating soil upto 30cm depth

& removing unwanted stuff, stones etc.Preparing soil

for planting by supplying and mixing fertile river soil

layer up to 15 cm. Excavating pits of required size and

4 providing cutting of cleredendron (kadavi mehndi) Nos 66.00 15.00

having height of 1 to 1.5 ft and bag size is 6 inch x 8 inch

and planting as directed & maintaining till well

established etc. complete (about 45 days )

Supply and Planting saplings of Ficus panda, Ficus

benjamina, Ficus benjamina variegated, Ficus

5 longisland bag size is 13 inch x 13 inch, well branched, Nos 65.00 150.00

well established & free from disease at site as per the

Supply and Planting saplings of (Jasud, Ixora, Ticoma

Gaudi-chaudi, Gultora, Jetropha, Haemeliya, Chandani,

Mogaro, Galfemia, , Allamenda, Desi Gulab, Euphorbia

mili, Jasud Hybrid, Chandani double, Madhukamini,

6 Madhumalti, Ticoma Capensis, Ixora draft, Nikadevia, Nos 65.00 85.00

English Karen etc.) having height of minimum 2.00 to

2.5 ft. and bag size is 8 inch x 10 inch, well branched,

well established & free from disease at site as per the

Supply and Planting saplings of Golden Bamboo having

height of minimum 5 to 6 ft. and bag size is 8 inch x

7 inch, well branched, well established & free from Nos 65.00 45.00

disease at site as per the instructions.

Supply and Planting saplings of Palm(Botal palm,foxtel)

having height of minimum 10.00 to 12.00 ft. and bag size

8 is 21 inch x 21 inch, well branched, well established & Nos 65.00 3500.00

free from disease at site as per the instructions

Supply and Planting saplings of champa (deshi)

having height of minimum 8 to 10 ft. and bag size is

9 inch x 16 inch, well branched, well established & free Nos 55.00 450.00

from disease at site as per the instructions.

Supply, Spreading and leveling of Brick dust (Chharu)

10 particle size having maximum 10 mm Cmt 29.00 1300.00

TOTAL LANDSACPING WORKS

Signature of contractor Additional City Engineer (NORTH ZONE)

Seal Ahmedabad Municipal Corporation

AHMEDABAD MUNICIPAL CORPORATION

MAHANAGAR SEVA SADAN - NORTH ZONE

Name of Work: - Construction of Party Plot for AMC at TP. no. 99 (Nana Chiloda) FP no 114, at

Sardarnagar ward North Zone, Ahmedabad

Sr. No. Description Amount

2 Plumbing Work

3 Electrical Work

4 Fire Fighting

5 Landscaping Work

I/We am/are willing to carry out work at ______ % above / below (should be written in figures and words)

the estimated cost mentioned above.

Estimated cost put to tender : RS. Estimated cost put to tender : RS.

Add_____% above : Rs ___________ Deduct_____% below : Rs __________

In words : Rupees _______________________ In words : Rupees_____________________

Signature of contractor Additional City Engineer (NORTH ZONE )

Seal Ahmedabad Municipal Corporation