Repair and renovation of EI work of Main building, compound light and installation of metal sign board at ITI P Roy Amtala

Amount

Supply and installation of L.T. cubical type fully compartmentalized distribution panel board, having rigid and self supporting structure fabricated with 14 SWG CRCA sheet with M.S. angle iron frame (main frame with 50 x 50 x 6 mm angle and each compartment with 40 x 40x6 mm angle iron). The base of panel should be made with 75mmx 40mm x 6mm M.S. channel. Each compartment will be providing with hylam board at back side. The panel should have cable alley at both side of panel. Incoming Arrangement : a) 415V, 315A TPN Switch Disconnector Fuse unit with HRC Fuse(Make –L&T/ABB/Siemens-Front handle) ---.1 No. Bus bar section : 500V, 400Amp capacity 99.9% – 99.5% electrolytic tinned 4 bar copper bus bar [size of flat [4x(2x 40 x 5 mm) / Equivalent size ] mounted on non-hygroscopic porcelain insulator / hylam sheet having sufficient di-electric strength duly wrapped with colour PVC tapes (Red, yellow, blue & black) for phases & neutral identification-1 Set

Interconnection :- All interconnection between incoming main to Busbar are to be made with suitable size electrolytic tinned copper bars or equivalent flexible pve insulated multistranded single core Cu cable and the same between busbar to each outgoing mains and & for metering arrangements are to be made by suitable size of Copper with proper socketing of the end of each wire leads. Installation :- The complete panel board is to be installed on suitable brick padestal incl. net cement finish as directed by the E.I.C. Painting: The complete panel board is to be spray painted after required surface treatment with 2 coat of red oxide primer & 2 coat of finished paint over dried or powder coating. Earthing :- A separate continuous aluminum earth busbar of appropriate size is to be painted at the inside bottom of the panel and run across the full load of the panel board. All electrical equipment are to be properly earthed with suitable size G.I. wire.

Supply and Installation of wall cum floor mounted L.T. cubical type fully compartmentalized distribution panel board , having rigid and self supporting structure fabricated with 14 SWG CRC sheet with M.S. angle iron frame (main frame with 50 x 50 x 6mm angle and each compartment with 40 x40x 6 mm angle iron). The base of panel should be made with 75 mm x 40mm x 4.4 mm M.S. channel . Each compartment will be providing with hylam board at back side. Incoming Arrangement : A) 415V, 250A TPN Main Switch unit with HRC Fuse ( Make- L&T/ABB/Siemens)-Front handle )- 1 No. B) Supplying and fixing 415V, 160A TPN on load front operated Changeover switch open execution type in SS enclosure/ cubical with nuts bolts etc (Make- L&T, Havells,HPL) Bus Bar Section : 500V, 315 Amp capacity 99.9% -99.5% electrolytic tinned 4 bar copper bus bar having size of flat [4 x50x5mm] mounted on non- hygroscopic porcelain insulator/hylam sheet having sufficient di-electric strength duly wrapped with colour PVC tapes ( Red , yellow , blue & black) for phases & neutral identification - 1 Set.

Intererconnection : All interconnection between incoming main to busbar are to be made with suitable size electrilytic tinned copper bars or equivalent flexible PVC insulated multistranded single core Cu cable and the same between busbar to each outgoing mains and for metering arrangements are to be made by suitable size of copper with proper socketing of the end of each wire leads . The complete panel board is to be spray painted after required surface treatment by 7 tanks process / sand blasting with 2 coat of red oxide primer & 2 coat of finished paint over dried or powder coating . Installation : The complete panel board is to be installed on suitable brick padestal incl. net cement finish as directed by the E.I.C. Earthing :- A separate continuous aluminum earth busbar of appropriate size is to be painted at the inside bottom of the panel and run across the full load of the panel board. All electrical equipment are to be properly earthed with suitable size G.I. wire.

S&F 415V, 8way, Betaguard Vertical type Main TPN PBDB with 3- phase incoming & TP/SP outgoings as follows, with vertical type bus-bar system, in SS enclosure (IP-42 protection) double door comprising of 4 nos link connector & provision for earthing attachment, concealed in wall after cutting the brick wall and mending good the damages to original finish incl. inter connection with suitable size of copper wire and earthing attachment as to G.S INCOMING –415V,125 A. FPMCCB 1 No. OUTGOING-415V, 63 A, TP MCB-8 Nos. [Make - Legrand/Siemens/Havells/ABB]

S&F 415V, Horizontal type, TPN MCB DB (6-way) with SS enclosure double-door with IP-42/43 protection with Four Pole Isolators as incomer and SPMCBs ('C' Curve, 10 kA) as outgoing, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment as per GS. INCOMING-63 A FP Isolator -1 No. OUTGOING-32A SPMCB-18Nos. [Make - Legrand/Siemens/Havells/ABB]

S&F 415V, Horizontal type, TPN MCB DB (4-way) with SS enclosure double-door with IP-42/43 protection with Four Pole Isolators as incomer and SPMCBs ('C' Curve, 10 kA) as outgoing, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment as per GS. INCOMING-63 A FP Isolator -1 No. OUTGOING-32A SPMCB-12 Nos. [Make - Legrand/Siemens/Havells/ABB]

Supplying and fixing double door sheet steel (16SWG), powder coated cable end box for TPN DB horizontal / vertical enclosure with IP-42/43 protection, on angle iron frame concealed & mending good the damages to original finish with nuts bolts etc incl. provision for earthing attachment. For 8way VTPN

For 6way HTPN

S&F 250V, (6-10)A per way, SPN MCBDB (8+2) 8 way with SS enclosure double-door(Ivory White with IP-42/43 protection with DP Isolators as incomer and SPMCBs ('C' Curve, 10kA) as outgoing, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment as per GS. ( For Light load & Computer) INCOMING-40 A DP Isolator OUTGOING- 8 Nos. 6-10A SPMCB [Make - Legrand/Siemens/Havells/ABB]

Supplying and fixing 415V, 50Hz,3-Ph MK1 DOL Starter on angle iron frame on wall with nuts bolts etc incl.Relay range-9-14A (Make-L&T) (Cat No-SS96210)

Supplying and fixing 230V, 50Hz, 1-Ph MU-2P Starter on angle iron frame on wall with nuts bolts etc incl.Relay range-9-14A (Make-L&T) (Cat No- CS90319KOAO)

Supplying & Fixing Industrial Plug & Socket board with 240 V, 20A, SPN & Earth Metal Industrial Plug socket & 20A Industrial top incl. S&F 20 A SP MCB breaking capcity 10kA (C- Curve) in SS enclosure fixed on wall and cecessary conection.

Supplying & Fixing Industrial Plug & Socket board with 415 V, 30A, TPN & Earth Metal Industrial Plug socket & 30A Industrial top incl. S&F 32 A TPN/FP MCB breaking capcity 10kA (C- Curve) in SS enclosure fixed on wall and cecessary conection.

Supply & Delivery 1.1 Kv grade 4Core 95 sq.mm. XLPE/Ar. AL Cable with earthing attachment in 2 x10 SWG G.I(Hot Dip) wire on wall/surface by MS saddles etc. and mending good the damages to original finish incl. removing the rubbish (From Palel to VTPN) [Make - Polycab/Havells/RR Kabel/Gloster]

Laying of one no. 1.1 Kv grade 4Core 95 sq.mm. XLPE/Ar. AL Cable on on wall/surface including S & F MS clams with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making hole etc. as necy., mending good damages and painting.

Supply & Delivery 1.1 Kv grade 4Core 35 sq.mm. XLPE/Ar. AL Cable with earthing attachment in 2 x10 SWG G.I(Hot Dip) wire on wall/surface by MS saddles etc. and mending good the damages to original finish incl. removing the rubbish (From Panel to VTPN ) [Make - Polycab/Havells/RR Kabel/Gloster]

Laying of one no. 1.1 Kv grade 4Core 35 sq.mm. XLPE/Ar. AL Cable on on wall/surface including S & F MS clams with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making hole etc. as necy., mending good damages and painting.

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) partly in 20mm size PVC rigid conduit 'FR' (Precision make) [for horizontal run & above false ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board complete with 2 no. suitable size “Ph & N” copper bar with top cover plate making earthing attachment fixed on wall incl. mending good damages to original finish. [PVC Rigid Conduit only for horizontal run & above false ceiling and vertical run concealed] (Avg run-8mtr)

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (approved make) partly in 20mm size PVC rigid conduit 'FR' (Brand approved by EIC) [for horizontal run & above false ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board on wall complete with 2 no. “Ph & N” copper bar incl. bakelite/ Perspex top cover 3 mm thick and incl. 175x100x65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finish [PVC Rigid Conduit only for horizontal run & above false ceiling and vertical run concealed] (Average run-9mtr) 2x22/0.3(P & N) and 1x 22/0.3

Distn. wiring in 3x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire(Brand approved by EIC) in 20 mm size PVC rigid conduit 'R' (Pecision Make) wit 1.1 KV grade 1 22/0. (1. sqm) single coe stranded 'FR' PVC insulated & unsheated copper wire as ECC,to 240V, 5A, 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch 2 nos.fixed on MS CRC sheet metal (16 SWG) switch board cu Bar on wall incl. (baelite/perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to origina finish. as to G.S.(avg run 7.5 mtr) for seperate plug.

Do ---- do – to 240 V 6A 5 pin plug point incl. S&F 240 V 6A 3 pin Modular type plug socket & Modular type switch (Legrand/Crabtree make) incl. S&F earth continuity wire, fixed on Board.

Do- do-do- to 6A plug point incl. S/F 6A Piano key type switch & 6A, 5 pin plug socket on Switch board as to G.S.

Distribution Wiring in 1.1 KV grade single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20/25/32mm PVC rigid conduit 'FR' incl. necy. fittings required. [Make-Finolex/KEI/Havells/Polycab] 2 x 22/0.3 (1.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC

2x36/0.3 (2.5 sqmm) + 1x22/0.3 (1.5 sqmm) as ECC ( For Power plug, Computer & compound Light)

2x56/0.3 (4 sqmm) + 1x22/0.3 (2.5 sqmm) as ECC (For AC machine)

2x84/0.3 (6 sqmm) + 1x36/0.3 (4 sqmm) as ECC in 25 mm polythene pipe (From TPN DB to SPNDB)

4x56/0.3 (4 sqmm) + 2x22/0.3 (2.5 sqmm) as ECC in 19 mm polythene pipe (For work shop Main switch to machine connection.)

4x126/0.4 (16 sqmm) + 2x56/0.3 (6 sqmm) as ECC from VTPN DB to HTPN DB)

Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

Supply & Fixing 240 V, 3 nos. 6A, & 1 no. 20A plug socket with separate 3 nos. 6 A & 1 no. 20A Piano key type switch, indicator & 20A switch type SP MCB (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 240x200x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

Supply & Fixing 240 V, 2x20A, plug socket with separate 2x20A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F suitable size MS (16SWG) switch board size-200mm x 150mm x 65mm,and bakelite /perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

Supply & Fixing 240 V, 2x6A, plug socket with separate 2x6A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F suitable size MS (16SWG) switch board size-175mm x 100mm x 65mm, and bakelite /perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

Supply & Fixing 240 V, 2x6A, 3 pin Modular type plug socket (Brand approved by EIC) with 2x6A Modular type switch without plug top on 6 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connection with PVC cu wire and earth continuity wire etc.As per direction of EIC.

Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Legrand make) with 16A , without plug top on 4 Module GI Modular type switch board with 4 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.As per direction of EIC.

Supply & Fixing 240 V, 1 no 16A, 3 pin Modular type plug socket with 1 no 16A Modular type switch & 1 no 6A, 3 pin Modular type plug socket with 1 no 6A Modular type switch without plug top on 6 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connection with PVC cu wire and earth continuity wire etc.As per direction of EIC.

Supply & Fixing 240 V, 1no. 16 A, 3 pin Modular type plug socket with 1 no. 16A Modular type switch & 3nos. 6 A, 3 pin Modular type plug socket with 3 nos. 6A Modular type switch (Legrand /Crabtree make), and without plug top on 12 Module GI Modular type switch board (Legrand/Crbtree make) with 12 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.As per direction of EIC.

Supply & delivery of 1200 mm sweep 230 volt AC Ceiling fan incl. Blades, canopy etc. With 18" down rod(14SWG), Fork(10SWG), Heavy type insulator, 3/8th inch bolt with nut, heavy type split pin etc., as directed by EIC [Make-Orient - New Breeze/Summercool or similar spec of Crompton/Usha]

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire.

Lowering and refixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. making necessary disconnection and connection as required.

S&F 240V,modular socket (2 Module) type fan regulator (step type) (Brand approve by EIC) on existing Modular GI switch board with top cover plate incl. making necy. connection etc.

S&F Socket type fan regulator (step type) (Brand approve by EIC) on existing sheet metel switch board with bakalite/perpex top cover by screws after making housing for regulator knob by cutting bakalite/perpex top cover incl. making necy. connection etc.

Supply and delivery of 230V 400 mm sweep Wall-fan, as directed by EIC. [Make: Orient / Usha / Crompton / Havells]

Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length.

S & F of of 240V A.C. 500 mm.(20") sweep pedestal Fan with all accessories incl. (make-Orient,model-Farrata FT-01 pedestal/Crompton-model-PF Windstar Farrata 20) as per direction of EIC. [Make: Orient-Farata Ft-01 / Usha / Crompton / Havells]

Supply & Delivery of 240V Air circulating, wall Mounting bracket Fan of 600 mm. dia, and fixing the same by proper adjustment including supply of necessary base plate & Fastener as per direction of E.I.C [Make: Orient-Wall 24 / Usha / Crompton / Havells]

Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length.

Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing and painting – (As per Drawing no. 475 of PWD Specification Book – May 1991)

Supply and delivery of Single LED Fitting (20Watt, 230VAC, 50hZ, 4000K NW, THD<10%, bult in 2.5KV SPD) with all accessories and 1 nos LED Tube [Make: Philips TMC 501 P 1xT-LED, Havells, Bajaj, CG, Wipro, Legaro, Halonix, Panasonic or as per EIC]

Supply and delivery of Twin LED Fitting (2x20Watt, 230VAC, 50hZ, 4000K NW, THD<10%, bult in 2.5KV SPD) with all accessories and 1 nos LED Tube [Make: Philips TMC 501 P 2xT-LED, Havells, Bajaj, CG, Wipro, Legaro, Halonix, Panasonic or as per EIC]

Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp whose one side fixed on ceiling with sutable size 4 nos. fastener and other side connected with the conduit with suitable size of bolts and nuts incl. S&F EI conduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length.. as per G.S. and direction of E.I.C.

Supply & Fixing 250V AC/DC superior type Call Bell ( Anchor-8320) on HW board incl. S & F HW board.

Extra for suspension exceeding 25 cm with S&F additional 2 nos. 20 mm dia E.I. Conduit(14 SWG) support as per G.S & necy. PVC insulated copper wire and painting etc, as per required.

Supply and fixing M.S down rod for A.C Ceiling Fan.

Supply & Fixing 240 V, 25 A, 3 pin Modular type plug socket (Brand approved by EIC), with 25A 3pin Modular type plug top with indicator and switch with 2 Module GI Modular type switch board with top cover plate flushed in wall and making necy. connections with PVC Cu wire and earth continuity wire etc.

Supply & Fixing 240 V, 25 A, Modular type starter (Brand approved by EIC) with 25A Modular switch type DP MCB (CCurve) and 4 Module GI Modular type switch board with 4 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level incl.earth excavation & restoring surface duly rammed (soft soil)

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Supply & drawing GI (Hot Dip) earth wire of No.6 SWG on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.

S&F of 9W LED lamp on exsting angular batten, as directed by EIC.

Supply & Delivery 9" dia exhaust fan incl. S&F Al. louver shutter after making hole on wall and mending good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection [Make: EPC Heavy Duty, Usha, CG, Bajaj or equiv Make]

Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter, as per GS (9" dia)

Supply and delivery of 230V 300mm (12") Exhaust fan with all necessary accessories, as directed by EIC. [Make: EPC Heavy Duty, Usha, CG, Bajaj or equiv Make]

Supply & Fixing louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long) for the above Exhaust Fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire & making connection for exhaust fan, as per GS.

S/F 800Amp HRC fuse link DIN type (Make-L&T)

S/F 400Amp HRC fuse link DIN type (Make-L&T)

S/F 100Amp HRC fuse link DIN type (Make-L&T)

S/F 63Amp HRC fuse link (LT)

S/F 32Amp HRC fuse link (LT)

Supplying and fixing 415V,63A Changeover switch with Sheet Steel enclosure on angle iron frame on wall with nuts bolts etc.(Make-Havells/HPL/Standard)

Supplying and fixing 415V, 125A TPN SFU open execution in existing SS enclosure/cubical with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.(Make-L&T/Siemens/Havells/ABB)

Supplying and fixing MCB SS enclosure with 32A DP MCB(C-10KA ) IP-20/30 protection, powder coated provision for two pole MCB, concealed in wall after cutting the wall & mending good the damages to original finish incl. painting, connection & provision for earthing attachment.(for work shop)

Supplying and fixing MCB SS enclosure with 32A TPN MCB(C-10KA ) IP-20/30 protection, powder coated provision for two pole MCB, concealed in wall after cutting the wall & mending good the damages to original finish incl. painting, connection & provision for earthing attachment (for work shop)

S&F 415V, 32A TPN main switch as to G.S(Havells/HPL/Standard) for Fitter workshop.

S&F 240V, 32A DP main switch as to G.S(Make-Havells/HPL/Standard ) for Fitter workshop

Laying of cable as below, after cutting floor/pavement/wall/ and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish From 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor/pavement/wall etc

Supplying and fixing compression type gland & Finishing the cable ends of following XLPE/PVC armoured cables as per PWD schedule 3.5 core 95 Sq.mm

4 core 35sq mm

Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes. 4x 16 +2x4sq mm

2x 6 +1x4sq mm

4x 4 +2x2.5sq mm

2x 4 +1x2.5sq mm

2x 2.5 +1x1.5sq mm

Supply & Delivery of 1.1 K.V. grade 2core 6 sq mm. XLPE Armoured Al. cable in underground trench /through G.I Pole as per G.S [Make - Polycab/Havells/RR Kabel/Gloster] In Underground trench.

Conseal in wall

Through Steel tubler Pole.

Laying of above 1.1 K.V. grade 2core 6 sq mm. XLPE Armoured Al. cable in underground trench /through G.I Pole as per G.S In Underground trench.

Conceal in wall

Through Steel tubler Pole

Supplying and fixing compression type gland & Finishing the cable ends of following XLPE/PVC armoured cables as per PWD schedule 2 core 6 Sq.mm

Supply & Delivery of Hot Dip Galvanised (as per IS:2629 / IS 2633 / IS 4759 and with its latest amendment ) Octagonal Pole made of HT steel ( sheet thickness -3mm ) conforming to grade S355 of BSEN 10025 alongwith welded base plate of required size conforming to IS: 226 / 2062 with integrated Control box with required sizes studs for termination of 2 core 10 /4 Core 16 sq mm Al (Armoured ) cable incld S&F 1 No 6 Amp SP MCB ( C-Series ) for each out going circuit to the fittings with proper pad locking arrangement for the following pole -- 7 Mtr Long [ Top Dia ( A / F ) - 70 mm, Bottom Dia ( A / F ) -135 mm ] Base Plate Size : 225 mm x 225mm x 16 mm. [Make - Bajaj / Utkarsh / Jindal / Subham]

Errection of the following Octagonal pole by designing and Casting RCC ( M 20 ) foundation of suitable size as specified below considering the safe soil bearing capacity at site as T/sq m, including excavation of earth, providing, cutting, bending and placing in position reinforcement as per drawing and providing pipe for cable entry and exit as required and providing and fixing of 4 Nos foundation bolts ( J Type ) as specified below and as per drawing on ground surface including back filling and cleaning extra earth -7 Mtr Long [ Founation size - 500 mm X 500 mm X 1200 mm, J Bolt Size - M 20 X 600 ] [SOR-P-H1-(A)-1(a)]

SITC of single dip galvanized steel overhang bracket ( Swan Neck Type/As per direction of the EIC ) at the top of the pole having 1.5 M length complete with all fixing arrangements as required including painting. Single Arm

Providing CC (6:3:1) muffing 450x450x600 mm in size or equivalent size of cylindrical muffing above ground level around the pole base complete with 3 mm thick neatly finished cement plaster all round after dismantling the unserviceable muffing if any incl. fixing only loop box if necessary. With 200x150x100mm 16 SWG GI Loop Box

Supplying and Fixing GI water proof looping cable box having hinged GI Top Cover having 4 mm thick with rubber gasket lining, railway type mechanical locking arrangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 15 A Kit-Kat fuse unit, one NL on porcelain insulator etc. and housing the same in pole muffing incl. addition and alteration to the existing CC muffing (6:3:1) after dismantling the damaged looping cable box etc. where necy. incl. painting 200 x 150 x100 mm

Wiring by 3x 1.5 sqmm single core PVC insulated copper wire (Finolex/Havells/Polycab) through polythene pipe from loop box to fitting as per direction of E.I.C.

S & F 40 mm. dia G.I. protection pipe ( ISI- M) through U.G. trench.

Excavation of soil for installation of Earth Electrode and filling & ramming

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level by ISI medium GI Pipe

Supply & drawing GI (Hot Dip) earth wire of No.6 SWG on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.

S & D 240V, 36 W LED street light made up of pressure die cast aluminium housing with IP66 protection ( Dust penetration-protected, jet - proof ) & IG cover. [Havells Cat No.ENDCITYLITEPLAT+SL36WLED757PASYBOPCWOSPD or equivalent spec of K-Lite/Philips/Crompton]

S & D 240V, 48 W LED street light made up of pressure die cast aluminium housing with IP66 protection ( Dust penetration-protected, jet - proof ) & IG cover. [Havells Cat No.ENDURACITYLITEPLAT+SL48WLED757PASYBOPC or equivalent spec of K-Lite/Philips/Crompton]

S & D 240V, 72 W LED street light made up of pressure die cast aluminium housing with IP66 protection ( Dust penetration-protected, jet - proof ) & IG cover. [Havells Cat NoENDURAOMNIPLUSSL72WLED757SASYTOPC or equivalent spec of K-Lite/Philips/Crompton]

S & D 240V, 150 W LED street light made up of pressure die cast aluminium housing with IP66 protection ( Dust penetration-protected, jet - proof ) & IG cover. [Havells Cat NoENDURAPEARLMAGNUMSL150WLED757PASYTOTGHO or equivalent spec of K-Lite/Philips/Crompton]

Fixing only outdoor / street light type fluorescent light fitting or MV light fitting complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 50 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc.

Supplying & Fixing GI water proof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint.

Supplying & Fixing bulk head light fitting (Havells make) with die cast aluminium housing & frosted glass on wall/ceiling incl. S&F 8watt CFL / 100 watts GLS lamp complete set as per G.S.

Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint.

Scraping, removing & cleaning the entire rust 9mtrs long steel tubler pole by Co's own tools, tackles & ladder arrangement.

Primer painting by one coat of Red Lead Primer.

Painting of Steel Tubular Pole of 9mtr length by 2coats of synthetic enamel paint (Whiite & Blue border)

S&F of 250V double door AC Timer DB [equivalent of 2+8 way SPNDB] with sheet steel enclosure, pnosphitised powder coated neutral bar, DIN rail with IP-43 potection comprising with 1 no. 25A DPMCB ('C' curve 10KA), 2 no. 16A SPMCB ('C' curve 10KA), 1no. Programmable time switch-24 hrs with minimum switching of 15 minutes and 1 no. 18A/25A 2-Pole power contractor with inner-outer plate & internal wiring by suitable size of cu. wire incl. 1 no. Auto-Manual bypass toggle switch and provision for earthing attachment, incl. LED indication light for running condition with mechanical locking arrangement, as directed by EIC. [Make-ABB/L&T/Crabtree]

S& F composite flash type board consisting of 1 no 20 AMP DPMCB on suitable MS BOX (16 SWG) with bakelight top cover and earthing attachment in conceal in wall as per direction of EIC ( for controlling Of HPSV)

Supply & Installation of metal sing board made of stainless steel high glossy anodized lettering to be fixed by supply & fixing Aluminium composite particle board (ACP) 5 mm thick having size (20 ft. x 4 ft each board.The ACP board to be fabricated on M.S. structure by 40 x 40 x 6mm angle iron frame and MS flat with appropriate size & dimension front facia will be convered by 16 SWG MS sheet. The high glossy lettering and logo will be fixed on the ACP Board over the front facia with stainless angle with SS screw. The sign board to be installed on parapet wall by scaffolding arrangement and arrangement for fixing of 3 nos. light fittings will be made. The Mater will be given in fiture at the time of execution.

Charges for making heavy type scaffolding arrangement for installation of the above metal sing board. construction of the supporting structure for multiple days as per direction of the EIC.

Supply and delivery 250 volt 50 watt LED outdoor type flood light fittings [Havells cat no-JETAQUANTOPLUSFLP50WLED757SYMLENS or equivalent spec of K-Lite/Philips/Crompton]

Fixing only above Floodlight Fitting with suitable tie clamps and MS plate for mounting on Pole/Tower or similar structure.

Supply & laying of 1.1kv grade 2x2.5sq mm +1x2.5 sq mm PVC insulated & unsheathed Cu wire drawn in 20mm dia PVC rigid pipe by shaddling on wall.

Painting with 2 coat synthetic enamel paint over 1 coat of zencromite primar after preparation of surface.

Supply and fixing of 2’x7” CRC sheet fixing by top of the metal board for save the rain water.

Carrying cost of above materials by track up & down with loading & unloading.

Note: 1) All the above rates should be quoted inclusive of all taxes & duties, District charges, Riverine charges and LWC as applicable, with cost of maintenance, servicing, supply & replacement of spares for 3 (three) years from the date of commissioning. 2) Total is rounded off to the nearest rupees.

MODERN ELECTRIC

Prava Enterprise

GHANASHYAM ELECTRIC STORES

MAHESWAR ELECTRICAL INDUSTRIES