REPAIR AND MAINTENANCE OF STEEL AND WOODEN MAP FURNITURE AT BINNAGURI STATION UNDER GE NORTH BINNAGURI

Amount

WOODEN FURNITURE Repairs to Peg Table for the following :- Removing old unserviceable fitting and fixture of Pag table without disturbing to the other parts such as legs,rails, top,stiffiners etc and supply and fixing with new items of Best quality 1 st Class Hard wood wellseasoned (TEAK) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 384)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1 st class hardwood (teak) beading around the edging.

Long rails

Short rails

Repairs to Teapoy for the following :- Removing old unserviceable fitting and fixture of Teapoy without disturbing to the other parts such as legs,rails, top,stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood well seasoned (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 382)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class harwood (teak) beading around the edging.

Long rails

Side rails

Repairs to Table Centre for the following :- Removing old unserviceable fitting and fixture of Table centre without disturbing to the other parts such as legs,rails, top,stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 274)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class haedwood beading around the edging.

Long rails

Side rails

Repairs to Table dining 6 person for the following :- Removing old unserviceable fitting and fixture of Table Dining 6 Person without disturbing to the other parts such as legs,rails, top, stiffiners etc and supply and fixing with new items of Best quality 1st class hardwood (Teak) and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : MAP/II/ 03)

Top of 18 mm thick particle board conforming to IS-3087-2005 with 1 mm thick plastic laminated sheet teak face shead on top using approved adhesive including 4mm thick 1st class hardwood (Teak) beading around the edging.

Long rail

Side rails

Repairs to Table Writing for the following :- Removing old unserviceable fitting and fixture of Table Writing without disturbing to the other parts such as legs,rails, top,stiffiners,Drawer etc and supply and fixing with new items of Best quality 1st class hardwood well seasoned (Teak) and 4mm thick wooden beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 275)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.

Sides of size 600mm x 560mm with 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.

Shutter of size 450mm x 350mm with 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging including 50 mm long brass hinges

Back 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 complete all as specified and as directed.

Shelve of cupboard 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.

25 mm dia chroumium plated Knob with brass nuts and bolts

Long rail

Side rails

Bottom Stiffeners

Taking out drawer from existing position and refixing the same after minor repair like tighting thr screw wooden pin complete all as specified.

Repairs to Table Bed side for the following :- Removing old unserviceable fitting and fixture of Table bed side without disturbing to the other parts such as top,legs,side, etc and supply and fixing with new items with 2nd class hardwood (Kalasiris) and 4mm thick wooden beading whereever required and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : E6/MAP/15(R))

Top/ bottom of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging.

Side of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging.

Back Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989

Shelve 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging.

Stiffeners

Repairs to Side board for the following :- Removing old unserviceable fitting and fixture of side board without disturbing to the other parts such as top,legs,side, top,drawers etc and supply and fixing with new items with 1st class hardwood (teak) and 4mm thick 1st class hardwood beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 1112)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class harwood (Teak) beading around the edging.

Side of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging.

Back Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989

Shutter 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging. with one knob 25mm dia complete all as specified and as directed.

Shelve 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging. complete all as specified and as directed.

Drawer 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging with one knob 25mm dia complete all as specified and as directed.

Inside partition 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging with one knob 25mm dia complete all as specified and as directed.

Bottom 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick timber beading around the edging complete all as specified and as directed.

Long rail of bottom

Short rail of bottom

Teakwood shaded knob 25mm dia

Repairs to Bin linen multipurpose for the following :- Removing old unserviceable fitting and fixture of Bin linen such as top, bottom, front /back side,legs etc and fixing with new 1st class hardwood (Teak) , 6 mm thick teakwood face plywood with 4 mm thick wooden beading whereever required all as directed and minor repair as per required applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: E6/MAP/09)

Top 1st class harwood well seasoned (Teak)

Bottom 1st class harwood well seasoned (Teak)

Legs 1st class harwood well seasoned (Teak)

Back side Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989

Repairs to Hat stand with mirror for the following :- Removing old unserviceable fitting and fixture of Hat stand with mirror without disturbing to the other parts such as Particle Board,matel peg,mirror etc and supply and fixing with new items of Best quality and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 233)

Base of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.

Chromium plated metal peg 120 mm long

Mirror 5 mm thick electro copper plated of size 300mm x 460 mm (Modi/Atul Saint Gobbin )

Repairs to Chair dining for the following :- Removing old unserviceable fitting and fixture of Chair dining without disturbing to the other parts such as legs,rails, stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood (Teak) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD MAP/II/05)

Rear legs 1st class hardwood (TeaK)

Front legs.1st class hardwood (TeaK)

Front / side rails of seat frame . 1st class hardwood (TeaK)

Back batten 1st class hardwood (TeaK)

Leg Stiffener 1st class hardwood (TeaK)

Taking out and removing all unserviceable wornout PVC seat frame of Chair Dining JCOs/ ORs and supply anf fixed new Seat frame complete all as specidied and shown in drawing.

Repairs to Table dining 4 person for the following :- Removing old unserviceable fitting and fixture of Table Dining 8 Person without disturbing to the other parts such as legs,rails, top, stiffiners etc and supply and fixing with new items of Best quality 1st class hardwood (Teak) and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : MAP/II/ 03)

Top of 18 mm thick particle board conforming to IS-3087-2005 with 1 mm thick plastic laminated sheet teak face shead on top using approved adhesive including 4mm thick 1st class hardwood (Teak) beading around the edging.

Legs 1st class hardwood well seasoned (TeaK)

Long rail 1st class hardwood well seasoned (TeaK)

Short rails 1st class hardwood well seasoned (TeaK)

Repairs to Table dressing Gents with Mirror (Drawing NO FD/E6/MAP/16) Mirror 5 mm thick electro copper plated of existing size and shape including 1st class well seasoned teak wood beading (Modi/Atul Saint Gobbin )

Taking out of unserviceable back long rail from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1680mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable stiffener in seat and back from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable Arm rest (Handle) from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing No. FD- 281)

Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell) (Drawing No. FD- 281)

Taking out of unserviceable back long rail from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1120mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable stiffener in seat and back from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable Arm rest (Handle) from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing No. FD- 281)

Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell) (Drawing No. FD- 281)

Taking out of unserviceable back long rail from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1680mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- MAP/II/02)

Taking out of unserviceable stiffener in seat and back from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- MAP/II/02)

Taking out of unserviceable Arm rest (Handle) from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- MAP/II/02)

Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing FD- MAP/II/02)

Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell) (Drawing No. FD- MAP/II/02)

Taking out of unserviceable back long rail from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1120mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- MAP/II/02)

Taking out of unserviceable stiffener in seat and back from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- MAP/II/02)

Taking out of unserviceable Arm rest (Handle) from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- MAP/II/02)

Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing No. FD- MAP/II/02)

Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell) (Drawing No. FD- 281)

Material and labour for preparing & polishing wooden and wood based materials of any description and of any lenghth and width and applying french polish to furniture articles as specified with one or more coat till glossy finish achieved including filler as required all as specified in particular specifications and as shown on drawing and as directed by EIC for the following wooden furniture:-

Peg Table (Drawing No. FD- 277/384)

Teapoy (Drawing No. FD- 278)

Table Centre (Drawing No. FD- 274)

Table Dining 6 persons (Drawing No. FD- MAP/II/03)

Table Writing (Drawing No. FD- 275)

Table bed side (Drawing No. FD- E6/MAP/15(R))

Side Board (Drawing No. FD- 26/241/ 1112)

Bin Lenin Multipurpose (Drawing No. FD- E6/MAP/09)

Hat stand with Mirror (Drawing No. FD- 206/233)

Chair Dining (Drawing No. FD- MAP/II/05)

Table Dining 4 persons (Drawing No. FD- MAP/03)

Table dressing gents with mirror (Drawing No. FD- E6/MAP/16)

Sofa Chair 4 Seater only (Drawing No. FD- 281, FD-18, FD/MAP/II/02)

Sofa set 5 (Five) Seater only (Drawing No. FD- 373, FD/MAP/II/02, FD-258)

Bed Ply wood Top (Escept plywood) (Drawing No. FD- 246 M)

Bin Solid Lenin Large/ Small (Drawing No. FD- 244)

Book Case Large/ Small (Drawing No. FD-237 M)

Chair Dining (Drawing No. FD- 16/279 and FD/MAP/II/05)

Chair Easy (Drawing No. FD-17/229)

Chair Writing (Drawing No. FD- 280)

Table Dining 6/8 Persons (Drawing No. FD- 273)

Stool dressing CB /Modified (Drawing No. FD- 27/282)

Table bed side (Drawing No. FD- 248)

Table dressing gents with mirror (Drawing No. FD- 31/230)

Table dressing ladies (Drawing No. FD- 33/249/251 and FD/MAP/II/07)

Table Writing (Drawing No. FD- 33/249 )

Table large 900 mm x 900 mm x 760mm (Drawing No. FD- 291)

Table 3' x 2' with drawer (Drawing No. FD- 224/283)

Table 3' x 2' with out drawer (Drawing No. FD- 223/284)

Rack Side 3 Space (Drawing No. WDF- 27)

Chair Wooden Bottom (Drawing No. FD- 225)

Almirah mess utencial (Drawing No. FD- 93(M)

Table Office Officer Wooden (Drawing No. FD- 84)

Foam with Back (Drawing No. FD-1027)

Foam without Back (Drawing No. FD-1027)

Sofa Set 5 (3+1+1) seater Wooden (Drawing No. FD-281)

Sofa Set 4 (2+1+1) seater Wooden (Drawing No. FD-281)

Sofa Set 5 (3+1+1) seater Wooden (Drawing No. FD- MAP/02)

Sofa Set 4 (2+1+1) seater Wooden (Drawing No. FD-MAP/02)

STEEL FURNITURE ( DRAWING No. FD/E6/MAP/18) Repair of Almirah steel large with shelves as appended below : Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing.

Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing.

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing.

Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing.

Taking down existing unserviceable Locking MS rod with locking device and cover from its position and supply and fixed new Locking MS rod with locking device and cover same as existing made out of MS round bar and 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing.

Taking out and removing existing unserviceable damaged lock from its position of almirah (large steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh

Taking out loose shelf from its position of Almirah large steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed.

Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm)

Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel large complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length)

Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed

Taking out and removing old unserviceable handle from its position of Almirah steel large and supply and fixed steel chromium plated handle 125mm long of existing shape and size as approved complete all as directed and shown on drawing.

CHAIR WRITING Taking out old damaged / decayed tapestray cloth and supply and fixed with new with superior quality tapestry cloth of approved colour, taxture and quality as per existing shape complete all as directed. ( DRAWING No. FD/E6/MAP/12) (Note : The cost of tapestry cloth should be min of Rs. 275/- per mtr).

Taking out old existing damaged / broken seat frame of chair verandah and refixing the same with new seat frame complete all as specified and as shown in drawing. (Make of seat frame : AMKO or equivalent as approved by GE). ( DRAWING No. FD/MAP/II/15)

Taking out old existing damaged / broken back frame of chair verandah and supply and fixed with new back frame complete all as specified and as shown in drawing. (Make of seat frame : AMKO or equivalent as approved by GE). ( DRAWING No. FD/MAP/II/15)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Note : Material to be weled not to exceeding 2.00mm in thickness)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of shoe rack steel complete all as specified and as shown in drawing. (Note : Material to be weled not to exceeding 2.00mm in thickness) ( DRAWING No. FD/E6/MAP/2(R)

Removing of old existing unserviceable plywood top from charpoy IP Hard Top MS squre pipe , tightening the frame including welding whereever required and Supply and fixing new plywood 12mm thick BWR, ISI marked, conforming to IS: 303-1989 (size Approx 1950 mm x 900 mm) with MS cleat and stiffener screw and cup washer all as spacified and directed. ( DRAWING No. FD/MAP/II/ 01)

Supply and fixing in repairs Stiffener of size 25mm x 25mm MS square tube1.5 mm wall thickness including necessary welding as per existing and as shown in drawing all as spacified and directed. ( DRAWING No. FD/MAP/II/ 01

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair school complete all as specified and as shown in drawing. (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking out old existing damaged / broken seat frame (PVC) of chair school and Supply and fixed with new seat frame (PVC) complete all as specified and as shown in drawing. (Make of seat frame : AMKO or equivalent as approved by GE). ( DRAWING No. FD/E6/MAP/05)

Taking down existing unserviceable Top of Table office clerk Steel and supply and fixed with new 6mm thick veneered decorative ply wood, grade 1st quality with BWR resin with decorative face veneer on one face in same position with new screws including providing aluminium beading all round as per existing shape and size complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1004)

Material and labour for spot welding in repairs of broken steel frame and drawer of table office clerk steel complete all as directed. (DRAWING No. 84(M)/FD-1004) (Note :- Each spot shall not exc. 5cm in length and not exc. 2mm in thickness.)

Taking down existing unserviceable Brass lock lever of Table office clerk Steel and supply and fixed with new Brass lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1004)

Taking down existing unserviceable Top of Table office Officer Steel and supply and fixed with new 6mm thick veneered decorative ply wood, grade 1st quality with BWR resin with decorative face veneer on one face in same position with new screws including providing aluminium beading all round as per existing shape and size complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1003)

Taking down existing unserviceable Brass lock lever of Table office Officer Steel and supply and fixed with new Brass lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1003)

Material and labour for spot welding in repairs of broken steel frame and drawer of table Office Officer steel complete all as directed. (DRAWING No. 84(M)/FD-1003) (Note :- Each spot shall not exc. 5cm in length and not exc. 2mm in thickness.)

Taking down existing unserviceable table top 900 mm x 600 mm with and without drawer Steel and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing & directed (Drawing No. FD 1007)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of Table complete all as specified and as shown in drawing. (Drawing No. FD 1007) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking down existing unserviceable table top 900 mm x 900 mm with and without drawer Steel and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing & directed (Drawing No. FD 1009)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of Table complete all as specified and as shown in drawing. (Drawing No. FD 1009) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking out unserviceable plastic cane of chair Verandah seat and back and supply and fixing for weaving the seat and back of Chair Varandah in Godrej pattern with new 4 mm wide half round approved quality cane on steel surface of chair complete all as specified and as directed. (Drawing No. FD-19(M)/256/359)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 19(M)/256/356) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking down decayed top from Table dining ORs and supply and fixing new top 18 mm thick pre-laminated particle board, Grade II Type I exterior grade conforming to IS-12823-2006 with 4mm thick teak wood beading all around the edging complete all as specified and as directed. (Drawing No. FD-165(M)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 165(M)/ Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking out unserviceable seat frame of Chair CBA Special with Hand rest and Supply and fixed Seat frame made from 2nd class hard wood well seasoned and termite treated duly canned in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out unserviceable Back frame of Chair CBA Special with Hand rest and Supply and fixed back frame made from 2nd class hard wood well seasoned and termite treated duly canned in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out unserviceable plastic cane from seat frame of Chair CBA Special with Hand rest and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out unserviceable plastic cane from back frame of Chair CBA Special with Hand rest and Supply and fixed for weaving the back of Chair in Godrej pattern with new 2 mm wide half round and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out all unserviceable hand rest from its position and supply and fixed new hand rest made out of 20 mm thick well seasoned teak wood plank in one piece on hand rest with piano hinges at right side complete all as specified and shown on drawing. . (Drawing No. FD-120)

Taking out all old unserviceable arm rest and supply and fixed new arm rest made out of well seasoned teak wood timber 25 mm thick duly polished as per existing shape & size complete all as per specified and as shown on drawing.(Drawing No. FD-120)

Material and labour for spot welding to damaged/broken seat frame of chair CBA spl with hand rest complete all as specified and shown on drawing. (Note : length of each spot welding will not exceed 8 cm in length and 2 mm in thichness).(Drawing No. FD-120)

Taking out unserviceable seat frame of Chair CB with Arm and Supply and fixed Seat frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable back frame of Chair CB with Arm and Supply and fixed Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of back frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Material and labour for spot welding to damaged/broken seat frame of chair CB with Arm complete all as specified and shown on drawing. (Drawing No. FD-75(M). (Note : length of each spot welding will not exceed 8 cm in length and 2 mm in thichness).

Taking out old rusted/damaged/broken flat iron support of chair CB steel with arms and supply and fixed new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Taking out old damaged/broken arm rest and supply and fixed new arm rest in the same position as per existing shape and size made out of well seasoned first class hard wood ‘Teak ’ timber including applying two coat of black paint over wood filler on all exposed new wooden surfaces after preparation of new wooden surfaces complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Taking out unserviceable seat frame of Chair CB without Arm and Supply and fixed Seat and Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable back frame of Chair CB without Arm and Supply and fixed Seat and Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Material and labour for spot welding to damaged/broken leg /stiffener of Form with back / Form without back complete all as specified and shown on drawing. (Drawing No. FD-77(M)/79(M). (Note : length of each spot welding will not exceed 8 cm in length and 2 mm in thichness).

Material and labour for spot welding to damaged/broken seat frame of chair CB without Arm complete all as specified and shown on drawing. (Drawing No. FD-75(M). (Note : length of each spot welding will not exceed 8 cm in length and 2 mm in thichness).

Taking out old rusted/damaged/broken flat iron support of chair CB steel without arms and supply and fixed new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Taking out old unserviceable wooden seat plank from Form with back and Supply and fixed new seat plank made out of 25mm thick well seasoned first class hard wood 'Teak Wood 'timber as per existing shape and sizes with 09 Nos GI nuts, bolts and washers including preparation of wooden surfaces and applying French polish to achive high glossy finish over wood filler to exposed surfaces of timber complete all as specified and as shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Taking out old unserviceable wooden back plank from Form with back and Supply and fixed new seat plank made out of 19mm thick well seasoned first class hard wood 'Teak Wood 'timber as per existing shape and sizes with 04 Nos GI nuts, bolts and washers including preparation of wooden surfaces and applying French polish to achive high glossy finish over wood filler to exposed surfaces of timber complete all as specified and as shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Taking out old unserviceable seat plank from 'form without back' and refixing the same with providing 09 Nos GI nuts bolts and washer complete all as specified and as directed and shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Taking down existing unserviceable Teapoy Verandah top and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing. (Drawing No. FD 35(M)/255)

Material and labour in repair to broken frame leg of teapoy verandah by spot welding not exc 2.50cm in length complete all as specified and as directed. (Note : Materials to be welded not exc. 2.50 cm in thickness).

Taking down existing unserviceable leg (Right/Left) of Locker bed side steel and supply and fixed with new Leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel sheet in same position and applying two coatss of Synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Material and labour in repair to broken/damaged bottom leg of locker bed side steel by spot welding complete as specified and as directed. (Drawing No. FD-257/1029) (Note: Thickness of metal to be welded shall not exceed 2mm.)

Taking out loose shelf from of locker Bed Side Steel and refixing the same position rigidly after minor repairs by providing new clips, nut and bolts as required complete all as directed. (Drawing No. FD-257/1029)

Taking out existing unserviceable hasp and stapple and Supply and fixed new hasp and staple of size 100 mm x 20 mm x 3 mm Chromium plated Hasp and staple to front shutter of approved make and design complete all as specified and as shown on drawing (Make :- Mowjee or Classic) (Drawing No. FD-257/1029)

Material and labour in repairing of existing unserviceable hinges by spot welding and make it functional by providing pin/greasing etc. complete all as directed. (Note :- Each spot welding shall not be more than 2.5cm in length and materials to be welded not exceeding 3mm in thickness.) (Drawing No. FD-257/1029)

Taking out of unserviceable old handles from the front of shutter and Supply and fixed new 115mm long chrome plated handle of approved make and design complete all specified and as shown on drawing. (Drawing No. FD-257/1029)

Taking out of old unserviceable broken curtain rod including brackets and Supply and fixed new curtain rod of aluminium 19/20mm dia, 1.5 mm wall thickness with steel brackets both sides in the same position by spot welding including painting with applying two coat of Olive Green synthetic enamel paint (1st quality over a coat of red oxide zinc chrome primer by spray machine over steel brackets after preparation of new steel surfaces complete all as specified and as shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged bottom shelf and Supply and fixed new bottom shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged intermediate shelf and Supply and fixed new intermediate shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged inner partition and Supply and fixed new inner partition as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged shutter (Left/Rigt) and Supply and fixed new shutter as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Repair of Almirah steel large with shelves as appended below : Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable door shutter shelve from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking out unserviceable damaged lock from its position of almirah (large steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1031)

Taking out old and removing old unserviceable handle from Almirah steel large and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg. (Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1031)

Taking out loose shelf from its position of Almirah large steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1031)

Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel large complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1031)

Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1031)

Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1031)

Repair of Almirah steel Medium with shelves as appended below : Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking out and removing of old broken/damaged steel of door shutter with necessary cutting in square/rectangle in shape and Supply and fixed new MS sheet as per existing size and shape not exceeding 100 Sq cm each made out of 1 mm thickness plain mild steel sheet fixed by run welding of required length including applying two coat of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer by spray machine all complete as specified and as directed. ( Drawing No. FD-67(M)/FD-1032)

Taking out unserviceable damaged lock from its position of almirah (medium steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1032)

Taking out old and removing old unserviceable handle from Almirah steel medium and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg .(Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1032)

Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel medium complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1032).

Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1032)

Taking out loose shelf from its position of Almirah medium steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1032)

Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1032)

Removing of old PVC shoe from various Type of Tables such as Table Writing, table 3'x2' with /witout drawer, Table 3'x3', table 2'x2' Table office Clerk, table dining 6/8 person, Sofa set etc. and replacing the same with new 25mm dia and 20 mm high be screwed to bottom of legs all as specified an das directed.

Removing of old PVC shoe/ Cap from various Type of Chairs such as Chair dining, Chair Writing, Chair Easy, Chair WB,Chaier CB etc.and replacing the same with new 20 mm dia and 10 mm high be screwed to bottom of legs all as specified an das directed.

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of exposed steel surface including frame and legs, applying one coat of synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Chair Verandah. (Drawing No. FD/MAP/II/15

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of steel surface (inside & outside surface) including doors shelves and legs, applying one coat of synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Almirah Large Steel with shelvess. (Drawing No. FD/E6/MAP/18

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of steel surface (inside & outside surface) including shelves and legs, applying one coat of synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Rack Shoe steel (Drawing No. FD-MAP/II/02(R)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of exposed steel surface including frames and legs, applying one coat of black synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Charpoy IP Hard Top (Drawing No. FD-MAP/II/01

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface internal and external and applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Table office clerk steel. (Drawing No. FD-1004/84(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface internal and external applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Table office officer steel (Drawing No. FD-1003/84(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Table 900mm x 900mm x 760mm (Drawing No. FD-1009)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Table 900mm x 600mm x 760mm (Drawing No. FD-1007)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of white synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Chair Verandah (Drawing No. FD-19(M)/256/359)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of black synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Table dining ORs steel (Drawing No. FD- 165(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Chair CBA Special with Hand Rest (Drawing No. FD-120)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Chair tubler steel /CBA Steel with arms?CBA Steel without arms. (Drawing No. FD- 75(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of Black synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Form with back/ Form without back. (Drawing No. FD- 77(M) /78(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Teapoy Varandah (Drawing No. FD-255/35(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Locker Bed Side Steel. (Drawing No. FD-257/1029)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface internal and external and applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Almirah Large Steel with Shelves (Drawing No. FD-1031/67(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface internal and external and applying one coat of Olive Green synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Almirah Medium Steel with Shelves (Drawing No. FD-1032/67(M)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of all exposed steel surface internal and external and applying one coat of Black synthetic enamel paint (1st quality) by spray paint machine complete all as specified and as shown on drawing for Chair Writing. (Drawing No. FD/E6/MAP/12)

samrat saw mill and joinery workshop

M/S East India Traders

M/S MAJUMDER CONSTRUCTION

M/S SARKAR BROTHERS

R K AGARWAL