Repairs to Perimeter wall and Apron fencing of Factory , Dighi Magazine, Riverside Magazine and Proof Range at AFK.

Amount

Site clearance including cutting of bushes, shrubs/ hurbs any type, soft/ loose soil/ as directed by Engg-in-charge.

Dismantling wrought iron or mild steel work (MS post) of any description not otherwise provided for

Demolition of cement concrete (unreinforced)/stone masonry of any description and in any position not otherwise specifically provided for embeding MS angle/ posts. Complete all as specified and directed.

Demolition of brickwork/ stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles.

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, Hard/ dense soil.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, Soft rock

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, Hard rock

M&L for providing cement concrete type B 1:2:4mix (20mm graded aggregate ) in foundations, filling and mass concrete.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, any type of beam, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete, flat

S & F Mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples steel pins, but in wire entanglements aprons, barriers, gates, etc. as directed (each line wire to be measured).

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples steel pins, but in wire entanglements aprons, barriers, gates, etc. as directed (each line wire to be measured), in repairs

M & L for Broken glass coping on top of walls, in cement mortar 1:3, including taking and removing rubbish out of premises.

M&L for preparation of new/ old or previously untreated steel or iron surfaces of any description, not otherwise mentioned over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer.

Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in 1:6 cement mortar, except stone

M&L for Keyed pointing to random or polygonal rubble, uncoursed or brought upto course in 1:4 cement mortar.

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete, Type C1 1:3:6 (20mm graded aggregate) Set in cement mortar 1:6.

M&L for rendering 20mm thick on fair faces of brick/ concrete/ any type of surfaces of walls in CM 1:4 including finishing the plastered surface even and smooth without using extra cement.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of walls in CM 1:4 including finishing the plastered surface even and smooth without using extra cement.

M&L for preparing plastered or unplastered new surfaces and applying two coats of cement paint on walls.

M&L for Reinforced cement concrete (nominal mix) in Beams, cantilevers, bressumm ers, lintels over 1.5m span, Type B1 1:2:4 (20 mm graded aggregate)

M&L for providing cement concrete type B1, 1:2:4 mix (20mm graded aggregate) in coping, parapets and railings upto 60cm height and the like including weathering slightly rounded or chamfered angles and throating as directed.

S&F for Mild steel Deformed or twisted bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S&F mild steel work Fe 410 -W (Gde E- 250) quality A in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

Supply of punch tape concertina coil with coil dia when closed 610mm and when open 580 mm(when opened upto 6mtrs.), weight of coil with 50 turn and 125 nos. clips 9kg(w/o handles and spike) and tolerance in wt. (plus or minus 5%) on perimeter wall.

Only fixing of concertina coil on perimeter wall.

Taking out existing defective concertina coil in repairs.

Credit Item-Dismantaling wrought iron or mild steel work as in Fencing post and the like of any description not otherwise provided for

Credit Item-Old stone masonry

V C SHETH (BID ID -911909)