SDP-Pamba-M and M festival in 1195 ME-Disposal of garbages at Pamba-Overhauling and operation of Incinerator Unit II and III including supply of spares and labour(New Incinerator)

Amount

APPENDIX A Maintenance to the droplet separator unit of each Incinerator by dismantling the unit from the incinerator assembly , and de-ashing the same using suitable chemical solution, Re assembling the unit using new high quality gasket, nuts, bolts and painting using heat resistant hammer tone painting .The work includes repairing and cleaning of ‘U’ bend connecting the droplet separator with ID fan consumables.

Maintenance to the ventury scrubbing unit of each incinerator by dismantling all the water inlet connections from the unit, cleaning the spray nozzles, inside surface, damper mechanism, thermo well and re assembling the unit using new gaskets, nuts bolts etc. the defective gaskets, nuts bots , . The rate inclusive all taxes cost of consumables etc.

Dismantling, overhauling, cleaning, and minor repair works to the FD fan assembly .The work includes complete cleaning of the impeller, motor, coupling and re assembling , and necessary patch work to the casing and painting . The rate inclusive of all taxes transportation and cost of consumables.

Maintenance, repairing and complete overhauling of primary chamber. (2 set) Cleaning the refractory lined furnace walls, arch, Patch work to the refractory lining and insulation layer using fire create cement ,bricks etc , making good the refractory lined charging door and ash doors using castables, and ceramic wool. The rate also includes complete painting (2 coats) of primary chamber out surface using heat resistant aluminium paint. The rates inclusive of all taxes, charges for tools and tackles, consumables and transportation charges.

Maintenance, repairing and complete overhauling of secondary chamber . (2 set)Cleaning the refractory lined furnace walls, arch, Patch work to the refractory lining and insulation layer using fire create cement ,bricks etc , making good the refractory lined ash doors using castables, and ceramic wool. The rate also includes complete painting (2 coats)of secondary chamber out surface using heat resistant aluminium paint. The rates inclusive of all taxes, charges for tools and tackles, consumables and transportation charges.

Dismantling of horizontal refractory lined duct connecting the secondary chamber with ventury scrubber , removing the defective refractory layer form the duct, cleaning and re casting the duct using refractory cement (grade whytete/K). the work also includes providing necessary ‘Y’ type jagers inside the surface for strengthening the refractory lining. The rate inclusive of all taxes cost of consumables , all tools , tackles , like tri-pole for lifting the duct.

Complete dismantling of mono -bloc burner assembly in primary and secondary chamber for the incinerators, cleaning of electrodes, solenoid valves, blower fans, transformer, burner rod, nozzle, photocell, sight glass, diffuser plate, cone etc., Reassembling and tuning of burner assembly for proper combustion of system. The rate inclusive of all taxes.

Labour charges for cleaning of fuel day tank, fuel lines, fuel filter , Rectification of leakages to the fuel line, valves, fuel pump, Replacement of gland packing, gaskets, oil seal for both the incinerators . The rate is inclusive of all taxes etc

Repairing and replacing the defective control panel ( without internal instruments like contactors, relays and isolater) with a new control panel shell made of CR sheet , powder coated . The work includes dismantling all the instruments like contactors, relays , connectors, wires , cables, controls , and isolator from the defective control panel, re fixing/replacing the above instruments after proper inspection- to the new control panel, re wiring the new control panel using new control/power cables, connectors, legs, fixtures like G channel, C channel , indication lamps , glands, screws etc and fixing the new control panel to the wall using structural supports

Dismantling overhauling cleaning and minor repair works to the ID fan assembly. The work includes reassembling the blower unit, motor, shaft, impeller, bearing block, in proper alignment and carrying out necessary cleaning and surface finishing for the outer casing, , necesssary patch work to the casing and repainting using heat resistant hammer tone paint and labour charges for replacing of bearings ,greasing of bearing and dyanamic balancing of impeller .The rate inclusive of all taxes transportation and cost of consumables.

Design , supply, fabrication of MS duct for replacing the defective duct portion between ID fan and chimney and emergency stack from ventury scrubber - duct having 400 mm dia , 4mm thick , with mitter bend flanges, drain point , etc coated with 2 coats of aluminum paint . The rate is inclusive of dismantling of existing duct , transportation charges etc

APPENDIX B - Spare Parts Thermocouple K Type (For primary chamber)

Thermocouple KER 710 (For secondary chamber)

Nozzle

V Belt B-97

RTD assembly for ventury outlet

Electrode Assembly

Hose Metallic Braided 3/8 x 40

Digital Temperature Controller 0-1200degC

Contactor 32 A,230 V coil

Contactor 18 A ,230 V coil

Overload Relay 14-23A

Overload Relay 4.5-6.5A

Overload Relay 1.4-2.3A

Diffuser Plate

Transformer 14.5 KVA

Solenoid Valve

Single phase preventer

Fuel pump AJ-6

APPENDIX C - Labour Charges Engaging overall Supervisor for 75 days. (1 No. /3Shift /day)(3*75=225 Nos.)

Engaging SCAVENGER for loading of garbages into the incinerator for 75 days.(2 Nos. of machines)(3 Nos./shift for 3 shifts/day /machine)(3*3*2*75)=1350 Nos.)

Engaging SCAVENGER to segregate plastic materials from the garbages for 67 days.(5 Nos./shift for 3 shifts/day)(3*5*75)=1125 Nos.)

Yellow mask

MattyMask

Rubber Gloves 14"

Rubber Gloves 18"

CINZAC ENGINEERS (INDIA) PVT LTD