Loading
Loading…
Loading…
Tender Value
₹2.1 Cr
EMD Value
₹2.5 L
Closing Date
18 Dec 2025, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
(PH-31)
Above/Below/Par
S AND T
13 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender. Similar nature of work means: Signaling works of RRI or PI or EI indoor works with or without outdoor works with supply of EI or relay and other signaling equipment
38 conditions · 6 needing a document upload
The following documents should be specified for submission along with tender:
A. List of Personnel, Organization available on hand and proposed to be engaged for the subject work.
B. List of plant Machinery available on hand own and proposed to be inducted own hired to be given separately for the subject work.
C. List of Works completed in the last three financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work, Date of actual start, actual completion and final value of contract should also be given.
D. List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award.
The tenderers whether sole proprietor , a limited company or a partnership firm he/they should submit authentic proof in terms of partnership deed, proprietorship documents etc. along with the tender. If he/they want to act through agent or individual partners should submit a power of attorney duly stamped and authenticated by Notary Public or by Magistrate in favour of specific person whether he/she/they are partners of the firm or any other person specifically authorizing him/her name to submit the tender, sign the agreement , receive money, witness measurements, sign measurement books , compromise, settie, relinquish any claims, preferred by firm and also sign No Claim Certificate and refer all or any disputes arbitration.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Instructions and conditions to Tenderers :
The tenderer is advised to study the tender document in www.ireps.gov.in portal carefully.
These Conditions of tender shall be read in conjunction with General Condition of Contract /2022 corrected up to advance 1.1.1 correction slip subject to modification, additions or supersessions by Special Condition of Contract and Specification if any
General Condition of Contract and Specification 2022 for 1.1.2 material and works of the N.F. Railway can be seen at the office of DRM(S&T) KIR N.F.Railway.
JOINT VENTURE will only be permitted in the tender value of Rs.10 (Ten) crore and above.
Contractor has also to submit execution programme within 15 days of issue of Acceptance letter or at the time of signing CA whichever is earlier.
All documents being submitted by the Tenderer(s) alongwith their offer shall have to be self attested by the Tenderer.
The Earnest Money and tender documents cost in respect of e- tendering will be accepted through net banking on payment gate way only.
Fixed Deposit Receipt (FDR) will not be accepted as EMD for tender invited on IREPS (e-tender portal). Authority Railway Boards letter No. 2014/CE-I/WP/5 of 01.09.2016.
The Security Deposit shall be 5% of the contract value. The Bid Security submitted by the Contractor with his tender will be retained/encashed by the Railways as part of security for the due and faithful fulfilment of the contract by the Contractor. Provided further that, if Contractor submits the Cash or Term Deposit Receipt issued from a Scheduled commercial bank of India or irrevocable Bank Guarantee Bond from a Scheduled commercial bank of India, either towards the Full Security Depositor the Part Security Deposit equal to or more than Bid Security, the Railway shall return the Bid Security, to the 4.1.1 Contractor. Balance of Security Deposit may be deposited by the Contractor in cash or Term Deposit Receipt issued from Scheduled commercial bank of India or irrevocable Bank Guarantee bond issued from Scheduled commercial bank of India, or may be recovered at the rate of 6% of the bill amount till the full Security Deposit is recovered. Provided also that in case of defaulting Contractor, the Railway may retain any amount due for payment to the Contractor on the pending "on account bills" so that the amounts so retained (including amount guaranteed through Performance Guarantee) may not exceed 10% of the total value of the contract.
Bid Security/Earnest Money: All the tenderers / Contractors have to deposit full Earnest money as stipulated in the tender 4.1.2 document through net banking or payment gate way only. Note the following manual modes : FDR will not be accepted as EMD for tender invited on IREPS (e-tender portal).
Contractors are allowed to make payments against this tender towards earnest money only through online payment modes available on IREPS portal like net banking, debit card, credit card etc. Manual payments through Demand draft, Banker's cheque, Deposit receipts, FDR etc. are not allowed.
Every tenderer shall state in the tender his postal address fully and clearly. Any communication sent in time to the tenderer by post at the said address shall be deemed to have reached the tenderer duly and in time. Important documents shall be sent by Registered post.
The tenderer shall be required to submit the Bid Security with the tender for the due performance with the stipulation to keep the offer open till such date as specified in the tender, under the conditions of tender. The Bid Security shall be as under: For works estimated to cost up to 1 crore - 2% of the estimated cost of the work. For works estimated to cost more than 1 crore- 2 lakh plus ½% (half percent) of the excess of the estimated cost of work beyond 1 crore subject to a maximum of 1 crore. The Bid Security shall be rounded off to the nearest 100. This Bid Security shall be applicable for all modes of tendering
The earnest money will be returned to the unsuccessful tenderer(s) after finalizing the tender. Till then Railway will not be liable to pay any kind of interest of the earnest money.
In terms of clause 16(4) of GCC 2022, The successful bidder shall have to submit a Performance Guarantee (PG) within 21 (Twenty one) days from the date of issue of Letter of Acceptance (LOA). Extension of time for submission of PG beyond 21 (Twenty one) days and upto 60 days from the date of issue of LOA may be given by the Authority who is competent to sign the contract agreement. However, a penal interest of 12% per annum shall be charged for the delay beyond 21(Twenty one) days, i.e. from 22ndday after the date of issue of LOA. Further, if the 60thday happens to be a declared holiday in the concerned office of the Railway, submission of PG can be accepted on the next working day. In all other cases, if the Contractor fails to submit the requisite PG even after 60 days from the date of issue of LOA, the contract is liable to be terminated. In case contract is terminated railway shall be entitled to forfeit Bid Security and other dues payable to the contractor against that particular contract, subject to maximum of PG amount. In case a tenderer has not submitted Bid Security on the strength of their registration as a Startup recognized by Department of Industrial Policy and Promotion (DIPP) under Ministry of Commerce and Industry, DIPP shall be informed to this effect. The failed Contractor shall be debarred from participating in re-tender for that work.
The successful bidder shall submit the Performance Guarantee (PG) in any of the following forms, amounting to 5% of the original contract value:- (i)A deposit of Cash; (ii)Irrevocable Bank Guarantee; (iii)Insurance Surety Bond as per Annexure-XVII. (iv) Government Securities including State Loan Bonds at 5% below the market value; (v)Pay Orders and Demand Drafts tendered by any Scheduled Commercial Bank of India; (vi)Guarantee Bonds executed or Deposits Receipts tendered by any Scheduled Commercial Bank of India; (vii) Deposit in the Post Office Saving Bank; (viii)Deposit in the National Savings Certificates; (ix)Twelve years National Defence Certificates; (x)Ten years Defence Deposits; (xi)National Defence Bonds and (xii)Unit Trust Certificates at 5% below market value or at the face value whichever is less. Also, FDR in favour of FA&CAO (free from any encumbrance) may be accepted.
The Performance Guarantee shall be submitted by the successful bidder after the Letter of Acceptance (LOA) has been issued, but before signing of the contract agreement. This P.G. shall be initially valid upto the stipulated date of completion plus 8.1.1 60 days beyond that. In case, the time for completion of work gets extended, the Contractor shall get the validity of P.G. extended to cover such extended time for completion of work plus 60 days.
The value of PG to be submitted by the Contractor is based on 8.1.2 original contract value and shall not change due to subsequent variation(s) in the original contract value.
The Performance Guarantee (PG) shall be released after physical completion of the work based on 'Completion Certificate' issued by the competent authority stating that the Contractor has completed the work in all respects satisfactorily.. The security deposit, however, shall be returned to the 8.1.3 Contractor along with or after, the following: (a)Final Payment of the Contract and (b)Execution of Final Supplementary Agreement or Certification by Engineer that Railway has No Claim on Contractor and (c)Maintenance Certificate issued, in case applicable
Whenever the contract is rescinded, the Performance Guarantee already submitted for the contract shall be encashed. The Engineer shall not make a claim under the Performance Guarantee except for amounts to which the President of India is entitled under the contract (not withstanding and/or without prejudice to any other provisions in the contract agreement) in the event of: (i)Failure by the Contractor to extend the validity of 8.1.4 the Performance Guarantee as described herein above, in which event the Engineer may claim the full amount of the Performance Guarantee. (ii)Failure by the Contractor to pay President of India any amount due, either as agreed by the Contractor or determined under any of the Clauses/Conditions of the Agreement, within 30 days of the service of notice to this effect by Engineer.
The Engineer shall not make a claim under the Performance Guarantee except for amounts to which the President of India is entitled under the contract (not withstanding and/or without prejudice to any other provisions in the contract agreement) in the event of: (i)Failure by the Contractor to extend the validity of the Performance Guarantee as described herein above, in which 8.1.5 event the Engineer may claim the full amount of the Performance Guarantee. (ii)Failure by the Contractor to pay President of India any amount due, either as agreed by the Contractor or determined under any of the Clauses/Conditions of the Agreement, within 30 days of the service of notice to this effect by Engineer. (iii)The Contract being determined or rescinded under clause 62 of these conditions.
The Bank Guarantee (BGs) to be submitted by the successful 8.1.6 contractors should be sent directly to the concerned authorities by the issuing Bank under registered Post A.D.
PARTNERSHIP DEEDS, POWER OF ATTORNEY ETC.FOR PARTNER(S)/ AGENT(S).
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be.
The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such 9.1.1 specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association/Board resolution, failing which tender shall be summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required.
(a)Should a tenderer i)be a retired Engineer of the gazetted rank or any other gazetted officer working before his retirement, whether in the executive or administrative capacity or whether holding a pensionable post or not, in the Engineering or any other department of any of the railways owned and administered by the President of India for the time being, OR ii)being partnership firm / joint venture (JV) / registered society / registered trust etc have as one of its partners/members a retired Engineer of the gazetted rank or any other gazetted officer working before his retirement, OR iii)being an incorporated company have any such retired Engineer of the gazetted rank or any other gazetted officer working before his retirement as one of its directors AND in case where such Engineer or officer had not retired from government service at least 1 year prior to the date of submission of the tender THEN the tenderer will give full information as to the date of retirement of such Engineer or gazetted officer from the said service and as to whether permission for taking such contract, or if the Contractor be a partnership firm or an incorporated company, to become a partner or director as the case may be, has been obtained by the tenderer or the Engineer or officer, as the case may be from the President of India or any officer, duly authorized by him in this behalf, shall be clearly stated in writing at the time of submitting the tender. b)In case, upon successful award of contract, should a tenderer depute for execution of the 9.1.2 works under or to deal matters related with this contract, any retired Engineer of gazette rank or retired gazetted officer working before his retirement in the Engineering or any other department of any of the railways owned and administered by the President of India for the time being, and now in his employment, then the tenderer will ensure that retired Engineer or retired gazetted officer had retired from government service at least 1 year prior to the date of his employment with tenderer and in case he had retired from service within a year then he possesses the requisite permission from the President of India or any officer, duly authorized by him in this behalf, to get associated with the tenderer. c) Should a tenderer or Contractor being an individual, have member(s) of his family or in the case of partnership firm/ company / joint venture (JV) / registered society / registered trust etc. one or more of his partner(s)/shareholder(s) or member(s) of the family of partner(s)/shareholder(s) having share of more than 1%in the tendering entity employed in gazetted capacity in the Engineering or any other department of the railway, then the tenderer at the time of submission of tender, will inform the authority inviting tenders the details of such persons. Note: -If information as required as per 16.a), b), c) above has not been furnished, contract is liable to be dealt in accordance with provision of clause 62 of the Standard General Condition of contract.
Restrictions on the Employment of Retired Signal & Telecommunication Engineers of Railway Services within One Year of Their Retirement :
The Contractor shall not, if he is a retired Government Engineer of Gazetted rank, himself engage in or employ or associate a retired Government Engineer of Gazetted rank, who has not completed one year from the date of retirement, in connection with this contract in any manner whatsoever without obtaining prior permission of the President and if the Contractor is found to have contravened this provision it will constitute a breach of contract and administration will be entitled to terminate the contract and forfeit his Performance Guarantee as well as Security Deposit.
Associated signaling work related to Yard Improvement at Samsi station of Katihar divison
KIR-N-2025-K-62~NFR
KIR-N-2025-K-62
Open
Works - General
12 Months
Katihar, Bihar
₹0
₹2.5 L
18 Dec 2025
26 Nov 2025
4 Dec 2025
217 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 2,08,49,136 | ||
| — | 1.00 | — | — | ||
| Modification of design and supply of equipment required for modification of existing Electronic Interlocking System (Kyosan make) to suit modified yard layout of Samsi station. The scope of work will include supply of all EI component e.g. input/output bits cards etc, all interface relays, interconnecting cables, connectors, terminals, mounting arrangements, fixures and accessories to make EI system functional. Redesigning of logic and interface circuit as per approved SIP, FAT and SAT of EI System, installation, programing, testing and commissioning of complete yard for data Input and configuration, simulation and functional testing and commissioning of electronic Interlocking system as per interlocking plan, supply of as made logic and interface circuit as per NFR practice station in both soft and hard copy. | — | — | — | 69,28,202 | |
| — | 2.00 | — | — | ||
| Supply and installation of Modular Power Supply Arrangement for VDU (42"-85") and Industrial PC (Embedded PC) with Input and Output Redundancy Arrangement and Hot Pluggable Modules (Make-Gallant or similar) as per TS | — | — | — | 4,16,856 | |
| — | 10.00 | — | — | ||
| SITC of intelligence Analog addressable Multi sensor type smoke detector with inbuilt fault isolator and integral response indicator with 360 degree viewing angle, Detector shall communicate 3 danger levels for differentiated alarm activation and high tolerance to dust, dirt, temperature fluctuation and air current. Detector should have unique address for communication and assigned through panel Mounting base as required with protection category of IP40 as per RDSO specification number RDSO/SPN/217 for existing installation for IPS room, Battery room and ASM room and OFC Room | — | — | — | 57,270 | |
| — | 1.00 | — | — | ||
| SITC of intelligent addressable manual call point with inbuilt fault isolator suitable for wall or surface mounting call point shall include test key feature without removing the glass also should have protection category of IP 44 and extra accessories as per RDSO specification number RDSO/SPN/217 for existing installation | — | — | — | 8,208 | |
| — | 1.00 | — | — | ||
| SITC of addressable input/ output module- within built isolator, shall have LED indication for normal, fault test and activation - shall have the option for configuration as fail safe operation as per RDSO specification number RDSO/SPN/217 for existing installation | — | — | — | 11,506 | |
| — | 75.00 | — | — | ||
| Supply and Installation of LHS cable as per RDSO/SPN/217 for existing installation | — | — | — | 92,025 | |
| — | 1.00 | — | — | ||
| Supply and Installation of LHS Interface module as per RDSO/SPN/217 for existing installation | — | — | — | 53,819 | |
| — | 2.00 | — | — | ||
| SITC of Intelligent addressable loop powered sounder cum beacon with base, in built fault locator with protection category of IP 42 as per RDSO/SPN/217 for existing installation | — | — | — | 27,492 | |
| — | 6.00 | — | — | ||
| CO2 type fire extinguisher of capacity 4.5 Kg as per IS Standard having ISI mark | — | — | — | 63,018 | |
| — | 1.00 | — | — | ||
| Supply of Micro-controller based Digital Earth Leakage Detector as per RDSO specification number RDSO/SPN/256/2025, version: 2.0 comprising of 12 -Channels for signaling circuits (24V DC and 110V AC ) | — | — | — | 1,57,374 | |
| — | 1.00 | — | — | ||
| Installation of Microcontroller based universal digital Earth Leakage Detector comprise of 12 channels including connection to data logger for fault generation | — | — | — | 7,282 | |
| — | 1.00 | — | — | ||
| Supply and installation of fault diagnostic software cum NMS software for networking from centralized location with monitoring unit consisting of a PC Intel Core i7 14th Gen processor 32GB DDR RAM, 2TB GB SDD, Intel Gigabit LAN support, Wifi 6, Bluetooth, JBL professional speaker, Window 11 Pro version with MS Office 2014 H/S including recovery Disk, Bluetooth Wireless mouse and keyboard, 27" QHD LED Monitor or better, 5 yrs McAfee Antivirus support along with 1.0 KVA Online UPS with hp 1018 or better Monochrome Printer, 6-Port 16A Extension Cable with Spike Buster and PC table and a revolving chair of Godrej make. | — | — | — | 2,28,290 | |
| — | 5.00 | — | — | ||
| Tag block 200 way with PVC transparent covers as per IRS: S 77/2006 Revision 1 and drawing number SA-24751 | — | — | — | 10,140 | |
| — | 1.00 | — | — | ||
| Validation, networking, testing of existing data logger including report generation. The scope of work includes all the analog and digital wiring of new relays and signaling circuits | — | — | — | 40,574 | |
| — | 50.00 | — | — | ||
| Relay , AC immunized Plug in type, Style QNA1 DC Neutral line 24V, 8F-8B contact, front and back contacts metal to carbon with plug board, retaining clip and connectors conforming to specification BRS:931A ; IRS:S 34 ; IRS:S 23; IRS:S 60-78 | — | — | — | 2,43,800 | |
| — | 25.00 | — | — | ||
| Relay AC immunized, plug in type, style QBCA1, DC Biased Contactor relay, 24V 2HF- 4B contact front contacts (Heavy Duty) and back contact metal to carbon complete with plug board retaining clip and connectors conforming to BRS: 943; IRS:S 34; IRS:S 23, IRS:S 60-78 | — | — | — | 1,46,700 | |
| — | 25.00 | — | — | ||
| Relay, plug in type, style QSPA1 Slow to Pick up AC Immunized, DC Neutral, Line Relay 24V DC, 8F-4B contacts front contacts and back contact metal to carbon complete with plug board retaining clip and connectors conforming to BRS: 933A; IRS:S 34, IRS:S 23, IRS:S 60-78 | — | — | — | 1,32,925 | |
| — | 25.00 | — | — | ||
| Relay, plug in type, style QL1 magnetic latch DC neutral line Relay 24V DC, 11F-4B contacts front contacts and back contact metal to carbon complete with plug board retaining clip and connectors conforming to BRS: 935A; IRS:S 34 and IRS: S 23 | — | — | — | 1,42,825 | |
| — | 1.00 | — | — | ||
| Preparation of Signaling documents SIP, VDUD, RCC, SWRD in Auto CAD as per standard format adopted in NFR. Softcopy in AutoCAD to be submitted along with hard copy as per instruction of supervisor in charge for further approval from competent authority. The scope of work includes the subsequent modification and revision in signaling documents as per TS | — | — | — | 59,015 | |
| — | 1.00 | — | — | ||
| Design, Preparation of as planned and as laid outdoor signaling documents in AUTOCAD and supply of its soft copy as well as hard copy for further approval and installations at site. It mainly consists of track bonding plan, cable route, plan, cable coarage plan, cable termination plan of relay room, location huts and location Boxes | — | — | — | 91,215 | |
| — | 1.00 | — | — | ||
| Preparation and supply of laminated six set of all completion drawings including circuit diagrams and documents as per TS | — | — | — | 46,185 | |
| — | 100.00 | — | — | ||
| Non deteriorating type of low voltage electric fuse 2A along with base for railway signaling as per specification IRS: S-78/2006 or latest | — | — | — | 16,600 | |
| — | 100.00 | — | — | ||
| Non deteriorating type of low voltage electric fuse of 6A along with base for railway signaling as per specification IRS: S-78/2006 or latest. | — | — | — | 25,900 | |
| — | 500.00 | — | — | ||
| Supply of Indoor signaling cables (PVC Insulated Multi core copper conductor) 60 core X 0.6 mm as per IRS: S 76/89 or latest | — | — | — | 1,51,000 | |
| — | 100.00 | — | — | ||
| 16/0.2mm size tinned flexible single core indoor wire to IRS: S-76/89, PVC coated in different colour and to be supplied in coils of 100 meters. | — | — | — | 89,800 | |
| — | 20.00 | — | — | ||
| Supply of PVC insulated unsheathed single core bright annealed bare copper conductor flexible cable (Size 2.5 Sq.mm) for voltage grade up-to 1100V confirming to IS: 694/1990 or latest. It is to be supplied in the coil of 100 meters. | — | — | — | 67,660 | |
| — | 20.00 | — | — | ||
| Supply of PVC insulated unsheathed single core bright annealed bare copper conductor flexible cable (Size 4 Sq.mm) for voltage grade up-to 1100V confirming to IS: 694/1990 or latest. It is to be supplied in the coil of 100 meters. | — | — | — | 97,560 | |
| — | 5.00 | — | — | ||
| Supply of PVC insulated unsheathed single core bright annealed bare copper conductor flexible cable (Size 10 Sq.mm) for voltage grade up-to 1100V confirming to IS: 694/1990 or latest. It is to be supplied in the coil of 100 meters. | — | — | — | 65,865 | |
| — | 4.00 | — | — | ||
| Supply of PVC insulated unsheathed single core bright annealed bare copper conductor flexible cable (Size 16 Sq.mm) for voltage grade up-to 1100V confirming to IS: 694/1990 or latest. It is to be supplied in the coil of 100 meters. | — | — | — | 70,688 | |
| — | 100.00 | — | — | ||
| ARA terminal block 6 Way made of PBT/poly carbonate as per specification number IRS:S 75/2006 (Rev.2) and drawing number 23756 or latest | — | — | — | 36,400 | |
| — | 3000.00 | — | — | ||
| Disconnect Terminal block for four conductor with screw-less Cage Clamp type/sliding switch disconnect as per RDSO Specification number RDSO/SPN/189/2004 version 3.0 for each conductor size up to 2.5 sq. mm. Each Terminal block equipped with two markers on top and bottom, end plate, 2 end clamps and adequate length rails for fitting terminal blocks | — | — | — | 6,24,000 | |
| — | 9.00 | — | — | ||
| Key lock checking relay (KLCR) with D.C. Neutral (AC Immunized) Relay working on 24 V DC for railway Signaling purpose as per RDSO specification number RDSO/SPN/219/2016 version 1.0 with amendment-1 | — | — | — | 1,06,731 | |
| — | 9.00 | — | — | ||
| Supply and Installation of KLCR box for fixing of KLCR inside box, including supply of all materials like board, handle, hinges, Godrej type padlock, glass sheets, supporting brackets etc. | — | — | — | 43,524 | |
| — | 1.00 | — | — | ||
| 4.6 meter Post with base, ladder, ladder base, platform for CLS unit as per IRS specification No. IRS; S 6-81 and drawing number SA-23153 (Adv). S-2011/M or latest | — | — | — | 23,250 | |
| — | 9.00 | — | — | ||
| 3.6 meter Post with base, ladder, ladder base, platform for CLS unit as per IRS specification No. IRS; S 6-81 and drawing number SA-23153 (Adv). S-2011/M or latest | — | — | — | 2,07,648 | |
| — | 6.00 | — | — | ||
| Colour light signal 4 aspect unit FRP TYPE to drawing number IRS: S-26/64, SA 23001 A/M (Adv.) or with latest amendment without CLS transformers, lenses, lamps, lamp holders. | — | — | — | 2,40,258 | |
| — | 4.00 | — | — | ||
| Colour light signal 2 aspect unit FRP TYPE to drawing number IRS: S-26/64, SA 23003 A/M (Adv.) or with latest amendment without CLS transformers, lenses, lamps, lamp holders. | — | — | — | 1,11,080 | |
| — | 1.00 | — | — | ||
| FRP Direction type route indicator 2 way as per IRS: S-66/84 Amendment 1, SA 23401- 6 (Adv.) or latest complete with fixing arrangement, brackets, hoods and terminals but without lamps, lamp holders and lenses. | — | — | — | 43,045 | |
| — | 1.00 | — | — | ||
| FRP Calling-On signal unit complete with fixing clamps, terminals etc. as per as per RDSO drawing SA-24351 (Adv.) Alt-1 but without lamp, lamp holder and lens. Fixing arrangement shall be as per RDSO drawing SA-24352 (Adv.) | — | — | — | 8,428 | |
| — | 12.00 | — | — | ||
| FRP Shunt Signal (Position light type) RDSO drawing number SA - 23840 (Adv.) with latest amendment for independent type complete with Signal unit, bracket, signal post of minimum 1 m length, surface base, terminals etc. but without lenses, lamps and lamp holders. | — | — | — | 3,91,284 | |
| — | 5.00 | — | — | ||
| FRP Shunt Signal (Position light type) RDSO drawing number SA - 23840 (Adv.) with latest amendment for dependent type complete with Signal unit, bracket, terminals etc. but without lenses, lamps and lamp holders. | — | — | — | 91,685 | |
| — | 1.00 | — | — | ||
| Offset bracket for colour light signal with fixing U clamps and nuts etc for Main Signal as per drawing SA 23080 Adv. or latest. | — | — | — | 1,834 | |
| — | 6.00 | — | — | ||
| Off set bracket for colour light signal with fixing U clamps and nuts etc. for Shunt /Co- On | — | — | — | 11,214 | |
| — | 10.00 | — | — | ||
| Excavation, ramming, Casting Cement Concrete foundation for Colour Light Main Signal Post in the ratio of 1:3:6 Aggregate not exceeding 3: 8 cm, as per IRSEM drawing number 19- D3, complete with contractor's material including cement, sand, aggregate, anchor bolts and nuts and curing of casted foundation, refilling & ramming of loose soil around foundation and disposal of loose dugged soil from site. | — | — | — | 98,410 | |
| — | 12.00 | — | — | ||
| Excavation, ramming, Casting Cement Concrete foundation for Position Light Shunt Signal Post in the ratio of 1:3:6 aggregate not exceeding 3: 8 cum, as per IRSEM drawing number 19- D4, complete with contractor's material including cement, sand, aggregate, anchor bolts and nuts and curing of casted foundation, refilling & ramming of loose soil around foundation and disposal of loose dugged soil from site. | — | — | — | 44,640 | |
| — | 4.00 | — | — | ||
| Assembling, erection, installation, taking of cable inside unit through post, termination and wiring of two aspect CLS unit complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets etc. including fixing and wiring of LED units lamps with contractor's wiring material. | — | — | — | 32,076 | |
| — | 6.00 | — | — | ||
| Assembling, erection, installation, taking of cable inside unit through post, termination and wiring of three/four aspect CLS unit complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets etc. including fixing and wiring of LED units lamps with contractor's wiring material. | — | — | — | 51,756 | |
| — | 1.00 | — | — | ||
| Assembling, erection, installation, taking of cable inside unit through post, termination and wiring of route indicator (1/2/3/4) unit complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets etc. including fixing and wiring of LED units lamps with contractor's wiring material. | — | — | — | 8,605 | |
| — | 1.00 | — | — | ||
| Assembling, erection, installation, taking of cable inside unit through post, termination and wiring of Calling on unit complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets etc including fixing and wiring of LED units lamps with contractor's wiring material. | — | — | — | 3,118 | |
| — | 12.00 | — | — | ||
| Assembling, erection, installation, taking of cable inside unit through post, termination and wiring of Independent type shunt unit complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets etc. including fixing and wiring of LED units lamps with contractor's wiring material. | — | — | — | 41,484 | |
| — | 5.00 | — | — | ||
| Assembling, erection, installation, taking of cable inside unit through post, termination and wiring of dependent type shunt unit complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets etc including fixing and wiring of LED units lamps with contractor's wiring material. | — | — | — | 13,105 | |
| — | 4.00 | — | — | ||
| Fabrication, supply and fixing of Retro-reflective P, C, A, G etc. marker disk of approved colour on signal as per standard practice and technical specification with contractor's complete material including fixing clamps. | — | — | — | 3,212 | |
| — | 28.00 | — | — | ||
| Fabrication, Supply and fixing of Retro-reflective Signal number plates of approved type as per technical specifications (Contractor has to arrange all hardware and other requirement to fix the plate on signal at his own cost) | — | — | — | 10,752 | |
| — | 10.00 | — | — | ||
| Supply and fixing of Universal Lock suitable for fixing on CLS units, MACLS calling on signal unit, route indicator unit and Position light type Shunt Signal units and sufficient number of Key. | — | — | — | 1,750 | |
| — | 6.00 | — | — | ||
| Electric Point Machine IRS type 220 mm throw, high thrust rotary locking type, non- trailable to operate on 110V DC (with 160 V AC immunized motor) as per RDSO specification number IRS: S-24-2025, Revision-3.0, and assembly drawing No. RDSO-S-11000 and RDSO S-3454 or latest complete with lock and detector slide, cable termination box, clamp Point lock 60 Kg TWS along with ground connection such as switch Extension Bracket (P-bracket), Insulation Plate R.H, Insulation Plate L.H, IRS Point. M/C-Detector rod (long and short), Lock rod (long and short), Drop Lug | — | — | — | 9,10,464 | |
| — | 2.00 | — | — | ||
| Electric Point Machine: 143 mm stroke, rotary locking type, non-trailable to operate on 110V DC (160 V AC Immunized motor) as per specification No. IRS: S 24-2025, Revision- 3.0 complete set as per technical specification | — | — | — | 2,01,864 | |
| — | 2.00 | — | — | ||
| Ground connections-threaded type complete set for 143 mm stroke, Rotary Locking Point Machine, suitable to the point layout of 60 Kg. / 52 Kg Rails as per yard layout for BG and for all make of the Point Machines | — | — | — | 17,790 | |
| — | 8.00 | — | — | ||
| Supply of GI bend pipe for leading cables inside the Point machines | — | — | — | 7,720 | |
| — | 16.00 | — | — | ||
| Points gauge tie plate insulation complete set as per technical specification | — | — | — | 4,864 | |
| — | 16.00 | — | — | ||
| Point machine ground connection insulation complete set including for P Bracket and L bracket insulation as per IRS: S 40/84. | — | — | — | 9,072 | |
| — | 6.00 | — | — | ||
| Installation, wiring and associated work such as drilling of switch, installation and adjustment of ground connections and insulations of 110V DC 220 mm throw IRS clamp type point machine for 60 Kg thick web switch with removal of existing Point machine as per standard practice and direction of supervisor in charge. Fixing of GI pipes with flange for taking cable into point machine, termination of tai lcable in point machine, adjusting opening of the switches and adjusting the point machine with crank handle (including all smithy and fitting works required at site for complete installation and fitting insulation for gauge tie plate. All the required consumable stores viz lugs of suitable sizes, nuts and bolts, washer etc. for completion of the entire work should be supplied by the contractor. | — | — | — | 1,27,374 | |
| — | 2.00 | — | — | ||
| Installation, wiring and associated work such as drilling of switch, installation and adjustment of ground connections and insulations of 110V DC 143 mm throw point machine with removal/shifting of existing Point machine as per instruction of supervisor-in -charge. Fixing of GI pipes with flange for taking cable into point machine, termination of tail cable in point machine, adjusting opening of the switches and adjusting the point machine with crank handle (including all smithy and fitting works required at site for complete installation and fitting insulation for gauge tie plate and William stretcher bar etc. All the required consumable stores viz lugs of suitable sizes, nuts and bolts, washer etc. for completion of the entire work should be supplied by the contractor | — | — | — | 22,584 | |
| — | 27.00 | — | — | ||
| Relay, plug in type, metal to Carbon, DC Neutral Track Relay, ACI, Style QTA2, 9 Ohm, 2F-1B Contact complete with plug-board, retaining clip and connectors conforming as per: BRS:939A and 966 (Appx F2) and IRS:S-23, S34 and 60 | — | — | — | 1,22,391 | |
| — | 10.00 | — | — | ||
| Relay, AC immunized, plug in type, style QBAT, DC Biased Track Relay, 9 Ohm, 2F-2B Contact front contacts and back contact metal to carbon complete with plug-board, retaining clip and connectors conforming as per specification No. RDSO/SPN/84 version 2; IRS: S 34, IRS: S 23, IRS S 60- 78 | — | — | — | 60,900 | |
| — | 37.00 | — | — | ||
| Supply of Track feed battery charger (capacity 10 Amps) to work on 110V AC for charging 1/2/3/4 lead acid cell of 80 AH used in track circuit as per Specification IRS:S-89/2013 Version 1.0 or latest | — | — | — | 2,22,333 | |
| — | 37.00 | — | — | ||
| Track feed resistance 30 ohm (Disc Type) as per drawing number SA 20163/M | — | — | — | 19,869 | |
| — | 74.00 | — | — | ||
| B Type Choke Coil for single rail track circuits on 25 KV 50 Hz AC electrified sections as per specification IRS: S-65/83 amendment 3 or latest | — | — | — | 3,14,722 | |
| — | 111.00 | — | — | ||
| Supply of Low maintenance lead acid stationary secondary cell as per specification number IRS: S-88/2004 version 1.0 or latest, nominal 2V, each of 80 AH with hard rubber container for use of Railway Signaling and Telecommunication application | — | — | — | 3,64,302 | |
| — | 111.00 | — | — | ||
| Charging of Secondary cells 80AH with Contractor's own charging equipment including supply of Sulphuric acid conforming to IS:266-1977, distilled water conforming to IS:1069-1964, installation, supply and application of acid proof foam spray of approved type on the terminals of charges batteries all activities as per technical specification | — | — | — | 41,736 | |
| — | 119.00 | — | — | ||
| Track lead junction box FRP type fitted with 2-way in box size 120 mm x 220 mm x 90mm x 6mm thick as per TS and as per drawing RST-11509 | — | — | — | 2,55,374 | |
| — | 1000.00 | — | — | ||
| PVC insulated cable 3/16" as per IRS specification S: 103-2004 made of copper alloy material tin plated non corrosive. | — | — | — | 2,18,000 | |
| — | 1000.00 | — | — | ||
| Channel bond pin single grove | — | — | — | 5,000 | |
| — | 22.00 | — | — | ||
| Installation and commissioning of DC track circuits (Not involving Point zone TC) including fixing of continuity bonds on rail joints and making rail connections of lead wires, installation and fixing of track lead junction box on MS angle for track feed end, track relay end and BX Jumpers, connections to tail cable, termination of tail cables on TLJB terminals etc., insertion of insulated block joints and also fixing jumper cables as per insulation diagram/track bonding plan, charging and adjustment of track circuit. All activities as per standard practice and as per instruction of site-in charge. | — | — | — | 1,36,290 | |
| — | 15.00 | — | — | ||
| Installation and commissioning of DC track circuits (Point zone TC) including fixing of continuity bonds on rail joints and making rail connections of lead wires, installation and fixing of track lead junction box on MS angle for track feed end, track relay end and BX Jumpers, connections to tail cable, termination of tail cables on TLJB terminals etc., insertion of insulated block joints and also fixing jumper cables as per insulation diagram/track bonding plan, charging and adjustment of track circuit. All activities as per standard practice and as per instruction of site-in charge. | — | — | — | 1,25,910 | |
| — | 30.00 | — | — | ||
| Supply and installations of wooden plank of size 450 mm (width) x approximately 40 mm (thickness), made from Sal wood or similar good quality commercial hard wood duly painted on all the surfaces, with two coats of acid proof paint for Battery racks in Battery room, at Location huts and locations, complete with contractor's material | — | — | — | 9,840 | |
| — | 5.00 | — | — | ||
| Supply of Stand made of saal/teak or similar wood for hydrometer. | — | — | — | 8,345 | |
| — | 10.00 | — | — | ||
| Supply of Hydrometer. Make: Thimson or superior quality. | — | — | — | 2,500 | |
| — | 10.00 | — | — | ||
| Apparatus cases Full made of 10 SWG sheets with miniature E Type Locks of same wards as that available on existing location box of station with keys as per RDSO drawing number S- 11500 with latest amendment. | — | — | — | 2,06,700 | |
| — | 10.00 | — | — | ||
| Excavation, ramming, Casting Cement Concrete foundation for Full Apparatus cases/Location boxes in the ratio of 1:3:6 Aggregate not exceeding 3: 8 cm, as per approved drawing with contractor's material including cement, sand, stones, anchor bolts and nuts and curing of casted foundation, refilling and ramming of loose soil around foundation and disposal of loose dugged soil from site. It includes installation of apparatus cases on CC foundation on grouted bolts, including filling the space enclosed below the location box | — | — | — | 89,130 | |
| — | 10.00 | — | — | ||
| Supply and Installation of Hylum sheet (Size 1200 mm X 1200 mm) for termination of main/tail cable including supply of terminal board as per TS | — | — | — | 33,080 | |
| — | 10.00 | — | — | ||
| Termination of signaling cable/wire in Apparatus case (Full)as per TS | — | — | — | 14,970 | |
| — | 5.00 | — | — | ||
| Cement concrete work for miscellaneous items in the ratio 1 : 3 : 6, aggregate not exceeding 3 : 8 cm including excavation, ramming, curing and plastering with 1 : 4 cement - sand mixture complete with contractor's material including cement, sand, aggregate and curing of casted foundation, refilling and ramming of loose soil around foundation and disposal of loose dugged soil from site. | — | — | — | 36,645 | |
| — | 20.00 | — | — | ||
| Supply of Earth electrode for outdoor equipment as per TS. GI pipe shall consist of spike at one end and a lug at the other for connecting the earth lead wire. | — | — | — | 45,180 | |
| — | 20.00 | — | — | ||
| Installation of Earth Electrode including supply of MS flat (with peripheral earthing of apparatus case) for signaling equipment as apparatus cases, signal, relay rack etc. | — | — | — | 70,020 | |
| — | 1.00 | — | — | ||
| Shifting, wiring, testing and commissioning of double detection digital axle counter for the block section at station including its associated all indoor equipment indication panel, monitoring console / interface computer and wiring the same to integrate with the relay circuits as per the instruction of supervisor in charge | — | — | — | 36,994 | |
| — | 2.00 | — | — | ||
| A set of complete earthing system, maintenance free tripod type complete as per RDSO/SPN/197/2008 with welded connecting rod and extension, copper cable for connection, Chemical Earthing with ultra-efficient Gel having earth impedance < 1 ohm for filling around earth electrode. It mainly consists of (a) Copper bonded steel electrodes of 3.0 m long, 17.0 mm diameter minimum with copper bonding thickness of min 250 micron and UL listed and marked- 3 No. (b) Earth Enhancement compound of RDSO approved brand supplied in sealed bags of min 10 Kg- 9 Nos. (c) Copper Strip of 200mm x 25mm x 6mm to exothermic welded to Earth electrode- 3 No. (d) Copper Strip of 300mm x 25mm x 6mm (MEEB) -3 No. (e) Copper Strip of 150mm x 25mm x 6mm (SEEB) -3 No | — | — | — | 1,37,612 | |
| — | 2.00 | — | — | ||
| Installation, carrying out necessary digging work for fixing earth electrode in ground, Commissioning of complete earthing system, consisting of Copper rod/strip, extension, cable connections, filling around earth electrode Chemical Earthing with ultra-efficient Gel having earth impedance < 1 ohm all work of earthing as per standard practice and connecting it to equipment to be earthed, supply and providing copper earth lead wires multistrand lead wires, exothermic bonding with contractor's material all connections between earth electrodes and earthing, one end to earth electrode and the other end of the wire to equipment as per site requirements | — | — | — | 11,608 | |
| — | 3500.00 | — | — | ||
| Excavation of trench 1.0 Meter deep and 0.3 Meter wide trenches in all type of soils except rocky area including clearing of roots of trees and bushes and temporary obstruction and refilling of the trench by the excavated soil and ramming after laying of the required quantity of cables as per instruction of site in charge. | — | — | — | 2,45,000 | |
| — | 300.00 | — | — | ||
| Excavation of trench 1.0 Meter deep and 0.3 Meter wide trenches in rocky and ballast filled soil, including clearing of roots of trees and bushes and temporary obstruction and refilling of the trench by the excavated soil and ramming after laying of the required quantity of cables as per instruction of site in charge. | — | — | — | 1,36,800 | |
| — | 43800.00 | — | — | ||
| Laying of signal and telecom Cable of different sizes as per cable route plan in the already dug trench with or without DWC pipe | — | — | — | 2,62,800 | |
| — | 300.00 | — | — | ||
| Supply and fixing of GI pipes/DWC pipes of all sizes and diameters/ troughing on culverts, bridges and any other loc. etc. complete with contractor's material including clamps, nuts and bolts and other fixing arrangements | — | — | — | 3,38,400 | |
| — | 200.00 | — | — | ||
| All works of excavation of cable trench 1.0 Meter deep, 0.3 Meter wide on pucca platform/on Road for road crossing and restoration of the platform/Road surface to original condition with contractor's material, after laying of GI/DWC pipes and then re-filling the trench | — | — | — | 1,75,400 | |
| — | 100.00 | — | — | ||
| Excavation of trench to a depth of 1 meter for track crossing of cables, laying of DWC/RCC/GI pipes with collar/coupler, refilling of trench by ramming and consolidating it as per the instructions of Railway representative at site. NOTE: During excavation of trench, it has to be ensured that the excavated soil does not mix with the ballast available. The depth of the 1m trench shall be from the bottom of the sleeper for track crossing. | — | — | — | 21,200 | |
| — | 200.00 | — | — | ||
| Manual Boring at the depth of 1m across the track/road as per technical specification. DWC/HDPE pipe will be supplied by Railway. | — | — | — | 69,600 | |
| — | 800.00 | — | — | ||
| Transportation of HDT machine with accessories including handling of store materials, preparation of site and boring (For 100 mm bore) for placing of different sizes of signaling cable together at bridges/Culvert/Track/Pucca road crossing /Yard area /station area, boring trench shall be minimum 3 meters below the river bed below the river bed and minimum 1.5 meter below surface in other patches/track/road/pucca platform. It also includes pulling of different sizes of S&T cables by HDT machine as per site requirement. The scope of work also includes supply of HDPE/DWC pipe and its accessories like sockets/couplers, T joints etc. | — | — | — | 10,41,600 | |
| — | 1000.00 | — | — | ||
| Transportation of HDT machine with accessories including handling of store materials, preparation of site and boring (For 63 mm bore) for placing of different sizes of signaling cable together at bridges/Culvert/Track/Pucca road crossing /Yard area /station area, boring trench shall be minimum 3 meters below the river bed below the river bed and minimum 1.5 meter below surface in other patches/track/road/pucca platform. It also includes pulling of different sizes of S&T cables by HDT machine as per site requirement. The scope of work also includes supply of HDPE/DWC pipe and its accessories like sockets/couplers, T joints etc. | — | — | — | 9,90,000 | |
| — | 1900.00 | — | — | ||
| Supply of HDPE/DWC pipe outer diameter 200 mm, inner diameter 175 mm for cable protection in trenches. | — | — | — | 11,45,700 | |
| — | 1900.00 | — | — | ||
| Cutting of DWC pipe, of various size, into 2 No. of split DWC pipe - includes transportation and loading/unloading required for cutting of DWC pipe as advised by supervisor in charge | — | — | — | 79,800 | |
| — | 3800.00 | — | — | ||
| Laying of HDPE/DWC split pipe (Half) of all sizes with socket, coupler and T Joint etc. for passing through the cable at normal soil etc. | — | — | — | 1,59,600 | |
| — | 1.00 | — | — | ||
| Taking the all types of cables inside station relay rooms, location boxes and junction boxes etc. and sealing of cable entry pit etc. as per technical specifications complete with contractor's material. | — | — | — | 24,925 | |
| — | 5.00 | — | — | ||
| Thermo shrinking jointing kit for jointing underground jelly filled Quad cable 6 Quad as per IRS: TC 77-2012, Revision. 3.0 with Amdt. 3 or latest. | — | — | — | 22,650 | |
| — | 5.00 | — | — | ||
| Installation of Thermo shrinking jointing kit for jointing underground jelly filled Quad cable including testing and commissioning of Quad link. | — | — | — | 6,840 | |
| — | 300.00 | — | — | ||
| Supply of HDPE/DWC pipe outer diameter 90 mm, inner diameter 76 mm with sockets/couplers and T joints where required | — | — | — | 73,200 | |
| — | 75.00 | — | — | ||
| Supply and installation of signaling cable route marker at site as per drawing including painting, lettering and transportation as per instruction of site -in charge. | — | — | — | 55,425 | |
| — | 6.00 | — | — | ||
| Supply and erection of Cable Termination Rack, Termination of cables, Frame, scaffolding/ ladder/angle, oven baked and Powder Coated with Biscuit matt colour, corrosive resistant and final finish with Siemens Grey (Sigma) enameled paint complete as per approved drawing with insulators, grouting bolts, tripods, rack fittings. ladder arrangement, hylam sheet board of 10mm thickness covering complete rack, all necessary fittings, supports, insulators, string rods to support cable, and other accessories etc. as per drawing and technical Specification and erection with scaffolding arrangement, fixing of tag block and all types of terminals on cable termination racks as per technical specification, in Relay Room and Location Huts. CTRs to be supplied of material same as Relay Racks | — | — | — | 2,01,420 | |
| — | 2.00 | — | — | ||
| Supply and installation of Stop Boards or calling on legend board, BSLB or other boards as per instruction with reflective Strips/reflective paper, making necessary foundation as per instruction complete with contractor material including angle for erection, supply and painting the board and post as per approved colour scheme complete installation | — | — | — | 11,348 | |
| — | 1.00 | — | — | ||
| Supply of paints, primers, varnish and other painting material, complete painting and varnishing , lettering, numbering of all signaling gears, including signal posts and fittings, apparatus cases, point machines, junction boxes, signal machine, rail post, other gears etc. complete at a station/mid-section gates/huts, letter writing on terminal Nos. apparatus cases, point machine, Signal Nos. and other details as per S.E.M. and instruction of engineer at site | — | — | — | 73,665 | |
| — | 1.00 | — | — | ||
| Dismantling of released materials and transportation along with surplus materials up to consignee's Go down by truck including loading and unloading as per instruction by consignee. | — | — | — | 23,497 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderDocumentK-62.pdf
ATTACHMENT
T-SIPofSAMSI.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .