Supply and Erection of Electrical Panel Boards at Various Ghats for forming Power Control Centres (PCC) in Ghat Areas of RMC (Under Pushkaram Funds)

Supply Installation Testing and commissioning of free-standing floor mounted dust and vermin proof compartmentalized cubical panel made out of CRCA sheet, required hardware, cleaning with 7 tank process duly painted by two coats of zinc/red oxide primer followed by Powder coated / epoxy / PU painted with phosphatisation in grey or required shade after rinsing. The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness, separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. The thickness of sheet shall not be less than 1.6mm up to 600mm length/ width of any compartment and be 2.0mm above 600mm. The load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Side walls and cable alley compartments having bolted type doors with detachable extension type structure (only outer area on all sides shall be measured and panel to be fabricated from CPRI approved fabricator). Panel board Size 6feetx4feetx14" of size including 250A Change over switch -1No, and MCCBS-6Nos, ELEC-6.2.1 and busbar channel and respective CT coil with ammeter and voltmeter and selctor switch with necessary wiring and all labour charges etc complete as directed by the departmental authorities

Providing, fabricating, supplying, erecting and fixing an MS protective shed of size 10'-0" (H) x 6'-6" (W) x 6'-0" (D), fabricated with 2"x2" MS square pipe posts and frame, including 5 Nos vertical posts (3 Nos front of 14 ft height and 2 Nos rear of 10 ft height), roof framing, 9 Nos intermediate supports of 1.25"×1.25" MS square pipe, one hinged MS door fabricated with 1.25"×1.25" MS square pipe complete with GI sheet roofing and side cladding, hinges, tower bolt, locking arrangement, welding, grinding, red oxide primer, two coats of synthetic enamel paint, foundation, erection and all incidental charges complete

Supply Installation Testing and commissioning of free-standing floor mounted dust and vermin proof compartmentalized cubical panel made out of CRCA sheet, required hardware, cleaning with 7 tank process duly painted by two coats of zinc/red oxide primer followed by Powder coated / epoxy / PU painted with phosphatisation in grey or required shade after rinsing. The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness, separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. The thickness of sheet shall not be less than 1.6mm up to 600mm length/ width of any compartment and be 2.0mm above 600mm. The load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Side walls and cable alley compartments having bolted type doors with detachable extension type structure (only outer area on all sides shall be measured and panel to be fabricated from CPRI approved fabricator). Panel board Size 6feetx3.5feetx14" of size including 250A Change over switch -1No, and MCCBS-6Nos, ELEC-6.2.1 and busbar channel and respective CT coil with ammeter and voltmeter and selctor switch with necessary wiring and all labour charges etc complete as directed by the departmental authorities

Details of Maximum amount reimbursable to the Contractor.

1. Provision for GST @18%

2. Provision for NAC @0.10%

Supply Installation Testing and commissioning of free-standing floor mounted dust and vermin proof compartmentalized cubical panel made out of CRCA sheet, required hardware, cleaning with 7 tank process duly painted by two coats of zinc/red oxide primer followed by Powder coated / epoxy / PU painted with phosphatisation in grey or required shade after rinsing. The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness, separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. The thickness of sheet shall not be less than 1.6mm up to 600mm length/ width of any compartment and be 2.0mm above 600mm. The load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Side walls and cable alley compartments having bolted type doors with detachable extension type structure (only outer area on all sides shall be measured and panel to be fabricated from CPRI approved fabricator). Panel board Size 6feetx4feetx14" of size including 250A Change over switch -1No, and MCCBS-6Nos, ELEC-6.2.1 and busbar channel and respective CT coil with ammeter and voltmeter and selctor switch with necessary wiring and all labour charges etc complete as directed by the departmental authorities

Providing, fabricating, supplying, erecting and fixing an MS protective shed of size 10'-0" (H) x 6'-6" (W) x 6'-0" (D), fabricated with 2"x2" MS square pipe posts and frame, including 5 Nos vertical posts (3 Nos front of 14 ft height and 2 Nos rear of 10 ft height), roof framing, 9 Nos intermediate supports of 1.25"×1.25" MS square pipe, one hinged MS door fabricated with 1.25"×1.25" MS square pipe complete with GI sheet roofing and side cladding, hinges, tower bolt, locking arrangement, welding, grinding, red oxide primer, two coats of synthetic enamel paint, foundation, erection and all incidental charges complete

Supply Installation Testing and commissioning of free-standing floor mounted dust and vermin proof compartmentalized cubical panel made out of CRCA sheet, required hardware, cleaning with 7 tank process duly painted by two coats of zinc/red oxide primer followed by Powder coated / epoxy / PU painted with phosphatisation in grey or required shade after rinsing. The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness, separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. The thickness of sheet shall not be less than 1.6mm up to 600mm length/ width of any compartment and be 2.0mm above 600mm. The load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Side walls and cable alley compartments having bolted type doors with detachable extension type structure (only outer area on all sides shall be measured and panel to be fabricated from CPRI approved fabricator). Panel board Size 6feetx3.5feetx14" of size including 250A Change over switch -1No, and MCCBS-6Nos, ELEC-6.2.1 and busbar channel and respective CT coil with ammeter and voltmeter and selctor switch with necessary wiring and all labour charges etc complete as directed by the departmental authorities