Dry -docking repair works of WB Jamanthy at Yard in Kochi during the year 2024-25

Amount

Charges for Docking / un - docking or beaching / un -beaching of the vessel

Dock hire charges (No extra dock hire charges will be entertained)

Mooring Charges for before and after dry-dock as well as during afloat repair works

Charges for ultrasonic testing of underwater hull and above water plates, onboard deck etc with Authorized agency. The copy of UT Gauge report shall be submitted to the office after completion of UT testing for the vessel immediately.

Dismantling of propellers Port & STBD sides (Make: Madras Marine industries, Dia:700 mm, Pitch:630 mm, P/D:0.9, No of blades:04, Type: Fixed pitch, no: 02), propeller shafts, checking the trueness of the shaft (Make: Madras Marine Industries, Dia:72 mm, Material: Stain less steel, no: 02), propellers, re-metalling, renewal of cut lash bushes etc. and re-fitting of the same along with propellers after balancing properly including labour charges.

Cost of Spare parts (Actual+10%)

Dismantling of rudder (Type:Plate type, Make: Startek shipyard Pvt Ltd,Chennai, Shaft: Dia.70 mm) and rudder stock, inspection of trueness, re-building of the same, making of new bushes, brackets etc. if any and re-fitting of the unit properly including labour charges.

Cost of Spare parts (Actual+10%)

Overhauling of both side sea suction in engine room, and cleaning of mud box including labour cost.

Cost of Spare parts (Actual+10%)

Renewal of under and above water level hull and onboard deck steel plates of 5 / 6 mm thick of ship building quality after cropping and removal of the damaged plates by gas cutting without any damages to other fittings such as electrical cables, pipelines, engines during removal of plates in engine room area (the cables should be protected during cutting and welding) other equpments etc & also section under water portion pipe to assed (to be done after getting ultrasonic test report and recommendation of Surveyor, Port Dept, Govt of Kerala including labour and material Cost.

Chipping, scrapping, wire brushing, buffing, shot blasting etc of external hull plate from keel to water level of the vessel properly (initially clean with fresh water with jet). Painting of the area with 2 coat of marine epoxy, 2 coat of chlorinated rubber antifouling paint including labour and material Cost.

Surface preparation of entire deck (from water level to deck surface) and super structure including out fittings by chipping, scrapping, wire brushing, buffing, shot blasting etc properly such as onboard deck, anchor winch, anchor cables (after dismantling), air vent pipes, hand pumps, bollards, wheel house, top of galley, railings, hatches, wheel house doors, stern gear compartment inside (rear side of vessel), diesel tank inside engine room inside (total sides:- top, bottom, both sides, ladder, pipelines etc), rudder compartment inside (all sides) and other fittings etc including labour and material Cost

Painting of entire deck (from water level to deck surface) and super structure including out fittings such as onboard deck, anchor winch, air vent pipes, hand pumps, bollards, wheel house, top of galley, railings, hatches, wheel house doors, engine room inside (total sides:- top, bottom, both sides, ladder, pipelines etc), stern gear compartment inside (rear side of vessel), rudder compartment inside (all sides) & other fittings etc with one coat of epoxy primer and 2 coats of epoxy marine quality enamel of existing colour properly. including labour and material Cost.

Removal of both main engine and Auxillary engine, fire pump and other accessories for renewal of under water plates in engine room below engines etc

Servicing of Auxilary generator including servicing of pulley pump, fuel pump and

Cost of Spare parts (Actual+10%)

Overhauling of 15 no valves in engine room, including labour cost

Cost of Spare parts (Actual+10%)

Cleaning of Bilge pipelines fitted in engine room including labour and material cost

Overhauling of both side Gear box (make: Twin Disc international S.A/Nivelles, Model:MG-5065-SC , Power: 276 KW, Reduction ratio: 2:1) gear not engaging properly including labour

Cost of Spare parts (Actual+10%)

Repairing of both side main engine damaged silencer Ms plate renewal at damaged area by cuttiing and rewelding inclduing labour and material charges.

Servicing of Port side radiator cooler and make in good working condition (fresh water leakage through inside sea water cooling lines) including labour charges.

Cost of Spare parts (Actual+10%)

Provision for dismantling and fitting of Plywood lamination with wooling fitted insidewheelhouse while renewal of wheelhouse top plate, and inside wheelhouse damaged areas including labour and material charges.

Checking and rectification of electrical issue (no electricty available during connnecting shore line and while using genenrator), the issue shall be rectified and renew all damaged wires inside wheel house with new one including labour Cost.

Cost of Spare parts (Actual+10%)

Repairing of STBD side main engine by rectifying the defect (oil fuel mixture) and make in good working condition including labour charges

Cost of Spare parts (Actual+10%)

Renewal of damaged hand rails with new pipe of same size and strengthening of damaged hand rail base portion by cutting and welding including labour and material charges

Fitting of Zinc Anodes (Location: Hull side shell): Zinc anodes,Type:ZHW-043, Net wt.:3.9 kg, Gross wt.:4.3 kg,Dim: 220X115X30, Qty:12, properly including labour and material Cost.

Fitting of zinc Anodes (Location: Rudder, Kort nozzle & sea chest) Zinc anodes,Type:ZHW-055, Net wt.:5.0 kg, Gross wt.:5.5 kg,Dim: 300x90x40, Qty:10 properly including labour and material Cost.

Repairing of Fuel measusing gauge fitted to the fuel tank inclduing labour and material charges

Reneqal of rubber beeding of 2 no entrance doors and 2 nos windows with new one incl labour and material charges

Re writing of vessel name, logo (IWAI), registration no, Port of registry, GRT on 4 locations of the vessel with size: 200 mm x 200 mm, load line, draft marking etc and on LSA & FFA vessel name, reg no, port of registry to be marked clear visibility including labour and material Cost.

Cochin Marine