SPECIAL REPAIR TO BLDG NO HT-103 OF 23 GRENADIERS UNDER GE (SOUTH) AMBALA CANTT

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for purlin/rafters, framed truss etc complete all as specified and directed.

Supply and fixing of mild steel, rolled sections as in main or cross beams, hip and jack rafters, purlin where connected to comman rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to grade Fe-410(Gde 250), complete all as specified and directed.

Description all as per item No 2 above but except material i.e. fabrication and fixing/irrection only complete all as specified and directed. (Note- The serviceable mild steel obtained from dismentling from item No 1 above will be used)

Supply and fixing of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa tensile strength as in roof covering/cladding to wall, fixed with self tapping screws or J type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi-corrugated sheets etc; complete all as specified and as directed.

Supply and fixing of pre-painted galvalume aluminium zinc coating GI based galvanised plain mild steel sheeting 0.50 mm thick of any colour, having 550 Mpa tensile strength as in roof covering/ ridges and fixed with self tapping screws or J type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi-corrugated sheets etc; complete all as specified and as directed.

Demolition of old brick masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed.

Material and labour for brick work with sub class 'B' (old size) bricks, straight or curved on plan, exceeding 6 mtr mean radius built in CM 1:6 etc complete all as specified and directed.

Supply and fixing of 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor etc including taking down existing pipe of any description complete all as specified and directed.

Supply and fixing of 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor etc including taking down existing pipe of any description complete all as specified and directed. .

Supply and fixing of 75 mm bore PVC (SWR) bend any radius complete all as specified and as directed.

Supply and fixing (in repair) of PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm bore outlet etc complete all as specified and directed.

Taking down cement plaster of any thickness on brick/stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:4) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer on walls complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer over a coat of wall care putty surface complete all as specified and directed.

Material and labour for preparation of old treated surfaces (Plastered or un-plastered) on walls, cornices, etc. by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of cement base paint, complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of walls and applying one coat of oil bound distemper on walls complete all as specified and directed.

Material and labour for preparation of old plastered surfaces of walls and applying one coat of white wash on walls complete all as specified and directed.

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre but not exceeding 4 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down shutter of any descritption exc 1.00 sqm each but not exc 2.00 sqm each including removal from site complete all as specified and directed.

Supply and fixing of mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging; also fastening and fixing conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Supply and fixing of steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219(c) sheet 1/3 to 3/3 and TD-220(c) sheet 1/3 to 3/3 as applicable including PCC (C-O ,1:3:6 using 12.5 graded aggregate) bed blocks for hold fasts and one shop coat of red oxide primer etc complete all as specified and directed. Note: (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery , grills 10mm square bars. (iii) Only Glazing, wire mesh & painting grill shall be measured & paid for separately)

Supply and fixing of factory made 35 mm thick, second class hard wood rail and style, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commrcial veneering on both faces ace, size of rails and stiles as per IS 1003 (part-I) kiln seasoned and chemical pressure treated complete all as specified and directed.

Supply and fixing of IInd class hard wood factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

Supply and fixing of factory made steel ventilator or window, fixed type with glazing bars, lugs including necessary PCC 1:3:6 type C-1 for filling bed blocks of hold fasts/lugs etc complete all as specified and directed.

Supply and fixing of factory made PVC hollow door frame of size 50mm x 47mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos, 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos of screws to be provided for each vertical numbers & minimum 02 Nos for horizontal member) complete all as specified and directed.

Supply and fixing of factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face including fixing in frame at site with 03 Nos SS hinges, 02 Nos aluminium tower bolt 150 mm, 02 Nos aluminium handle 150 mm for each shutter all as per specification & drawing complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed.

Supply and fixing of sheet glass 3mm thick, ordinary quality , in square not exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed.

Supply and fixing of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanized wire staple complete all as specified and as directed.

Supply and fixed (in repair) of sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square n.exc 0.5 Sqm each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed.

Supply and fixing of butt hinges, 100mm long, medium weight, cold rolled, mild steel complete all as specified and directed

Supply and fixing of aluminum anodized, barrel tower bolts of extruded section 150mm long complete all as specified and directed.

Supply and fixing of 150mm long extruded aluminium alloy handles, fabricated type, anodised complete as specified and directed.

Supply and fixing of 300mm long mild steel sliding door bolts, stove enameled black with bright bolts not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate complete all as specified and directed.

Material and labour for preparing new or previously untreated wood or wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Material and labour for preparation of old wood and wooden based surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 7 to 8 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:3) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material & labour for premium quality coloured glazed ceramic tiles (300x 200x 7mm thick) in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:4 including dismantling of old floor or wall tiling including cement mortar bedding and removing the rubbish outside the defence land complete all as specified and as directed.

Material and labour for 50mm thick PCC (1:3:6) type C-1 using 20mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mt centre to centre and at every turning & filling the joints with bitumen & sand mixture including demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) or complete all as specified and directed.

Supply and fixing in repair of angle valve, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with capstain head, heavy with adjustable wall flange complete all as specified and directed

Supply and fixed in repair of stop cock, fancy type, chromium plated, long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified.(Note : Weight of stop cock shall not be less than 0.575 Kg) (Note : Weight of stop cock shall not be less than 0.575 Kg)

Supply and fixed in repair of CP bib tap screwed down high pressure, long body, cast copper alloy, chromium plated` with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. (Note : Weight of bib tap shall not be less than 0.575 Kg)

Supply and fixing in repair of vitreous china wash down water closet pedestal pattern (EWC), White including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified and directed.

Supply & fixing in repair of vitreous china wash hand basin white flat back of size 550x440mm including CI brackets and 15mm chromium plated pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, PVC connection 450 mm long having PTMT nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including 32 mm dia PVC waste pipe etc., complete all as specified and directed.

Supply & fixing in repair of 10 litre capacity flush polypropylene cistern, ISI marked, white at low level complete with PVC bend/flush pipe and making all connection including taking down existing high/low level cistern with all connections and making good the disturbed surfaces in cement mortar (1:3) to match with the existing surface, complete all as specified and directed.

Supply and fixing in repairs PVC coloured bath cabinet overall size 16"x16" decorative design with looking mirror, nepkin rail complete all as specified and as directed.

Supply and fixing in repair of chromium plated towel rail 600mm long complete all as specified and directed

Supply and fixing in repair of chromium plated soap dish with fitting complete all as specified and directed.

Supply and fixing in repair of fancy type, shower rose 125mm size , brass Chromium plated, revolving type, fixed to existing steel pipe or union 15mm bore complete all as specified and as directed.

Supply and fixing in repair of 32/40mm bore PVC waste pipe suitable for urinal/WHB/ Sink etc complete all as specified and as directed.

Supply and fixing in repair of PVC connections 45cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and as directed.

Supply and fixing of GI tubing, ISI Marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing of GI tubing, ISI Marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing of water storage tank of 1000 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fixing of semi perforated false ceiling 12 mm thick with micro tegular edged at all height with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and pattern having moisutre content less than 2%, humidity resistance of 99%, NRC 0.60 to 0.85 as per IS 8225-1987, non combustible as per BS 475 (Part-4) 1970 and light code description unit code No 429 Sub Head 26. New Technologies and materials reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T -grid of hot dipped galvanised iron section of 0.33 mm thick ( galvanised @ 120 gms/ sqm including both sides) comprising of main T- runners of size 15x 32mm of length 3000mm, cross T of size 15 x32 mm of length 1200mm and secondary intermediate cross T of size 15 x 32 mm of length 600 mm to from grid module of size 600 x 600 mm, suspended form ceiliing using galvanised mild steel items (Galvanised @ 80 gm/sqm) i.e. 50 mm long, 8mm outer diameter M-6 dash fastners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85 x 25 x 2mm. galvanised iron perimeter wall angle of size 24 x 24 x 0.4 mm of length 3000 mm to be fixed on perimeter wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall SS screws. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge including dismantling existing asbestos sheet false ceiling textile coverings including frames (if any) and cover fillets complete all as specified and directed.

Material and labour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt/loose materials from the bricks and from the joints between the bricks. Prepared surface should be then washed with diluted HCL acid (dilution ratio of 1:50) for three times in a day for two days. After acid wash surface should be allowed to be air dried for one day. NOTE : - Further treatment over the surface so achieved will be carried out only after approved of the same by GE.

SCHEDULE A PART I (E&M WORKS) Dismantling/taking down carefully aluminium/ copper point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 25 mm dia with FRLSH accessories, concealed and including provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light/fan point/bell point controlled by one switch complete all as specified and directed. NOTES : - (i) The quoted rates shall be deemed to be inclusive for cutting chases by chase cutter in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary accessories/fittings. (ii) Point wiring & earth wire shall be connected to each & every flush/sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.

Description all as per item No 65.00 above but for ceiling fan point complete all as specified and directed.

Description all as per item No 65.00 above but for exhaust fan point complete all as specified and directed.

Description all as per item No 65.00 above but for socket out let point 5 Amps on same board complete all as specified and directed.

Description all as per item No 65.00 above but for socket out let point 5 Amps on independent board complete all as specified and directed.

Description all as per srl item No 65.00 above but point wiring for one socket out let 15&5 Amps (independent) controlled by one switch with using 2.5 Sq mm (nominal area) stranded copper conductor complete all as specified and directed.

Supply and fixing of switch piano 6 Amps, flush type, single pole, one way, 230 volt , AC supply, ISI Marked, complete all as specified and directed.

Supply and fixing of switch piano 16 Amps flush type one way 230 Volts, 50 Hz, AC supply, ISI Marked, complete all as specified and directed.

Supply and fixing of socket outlet 3 pin 6 amps, 230 volt. flush type, ISI Marked, complete all as speciied and directed.

Supply and fixing of socket outlet 16 amps, 230 volt flush type, ISI marked complete all as specified and directed.

Supply and fixing of ceiling rose surface bakelite 65 x 50mm, 3 terminal complete all as specified and directed.

Supply and fixing of fan regulator electronic step type ,230 Volts, AC supply, suitable for ceiling fan any type/make/sweep, complete all as specified and directed.

Supply and fixing of lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Supply and fixing of LED lamp 9 watt suitable for batten holder including taking down existing lamp of any description complete all as specified and directed.

Supply and fixing of channel for fixing of LED tube rod, aluminium housing body in CRCA body suitable for 18/20 watt LED tube, high efficient, AC 220-240 volts, 50 Hz and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. ( Note: Tube rod shall be measured and paid for separately).

Supply and fixing of 18 W/ 20W Polycarbonate LED tube light, environment friendly, high efficient, T8 with aluminium extrusion heat sink for optimum performance with high luminous efficiency and easy and taking down existing tube light and removal complete all as specified and directed. Note: - Tube rod must be get approved from Engr in charge to check fesibilty i.e. one end contact or two end contact for fixing in existing LED fittings.

Supply and fixing of decorative surface mounted LED tube light fitting with high efficient diffuser mirror light, aluminium housing in CRCA body suitable and including 10 watt LED tube high efficient, AC 220-240 volts, 50 Hz and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed.

Supply and fixing of bulk head light fitting, 10 watt, energy efficient with lamp 10 watt with provision of 2/3 core PVC copper conductor cable 0.5 Sqmm size from ceiling rose to light fitting complete including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed.

Supply and fixing sheet metal enclosures vertical distribution board VTPN, (MCCB DB) 4 ways, double door, 415 volts with 200 amps rated bus bar IP 43 protection, with shrouded neutral bar and insulated bus bar and earth link, with and including MCCB 4 pole, 125 Amps, 25 KA as incomer and MCBs as out going complete with making suitable size of MS cabinet 2 mm thick dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs and making good the disturbed surface matching with existing surface including taking down existing unserviciable MCCB/DBs including MCBs complete all as specified and directed.

Supply, installation, testing of SPN distibution board 8 way,double door , IP 43, as per IS 8623 including 200 Amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles including taking down existing unserviciable MCB/DBs including MCBs complete all as specified and directed.

Supply and fixing of MCB single pole and neutral, 240 volts, 50Hz , breaking capacity 10KA, 'B' curve 40 Amps, including connection with suitable size copper lugs complete all as specified and directed.

Supply and fixing of MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, 'B' curve 6 to 32 Amps, including connection with suitable size copper lugs complete all as specified and directed.

Supply and fixing of MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, 'B' curve 40 to 63 Amps, including connection with suitable size copper lugs complete all as specified and directed.

Supply, installation and testing of storage type heater (Geyser) of 25 Litres Capacity, vertical type to sustain high pressure upto 8 bars with fixing bolts / fastener, necessary PCC/cement work and making good the disturbed surfaces to match with existing surface giving electric and water connection and testing after installation to entire satisfaction of the Engineer-in-Charge complete with following specifications : - (a) 5 Star rated (Vertical type) Necessary BEE cerificate from OEM shall be produced by the contractor at the time of sample approval. (b) Metal Body (Shock proof and rust proof) (c) Glass line coated tank (Ferro-glass technology) / Polymer coated. (d) Incoloy glass coated heating element. (e) Adjustable thermostat. (f) Temperature indicator dial/digital type. (g) Multiple Heating Option. (h) Multiple Functional Safety Valve. (j) Thermal Cutout Capillary Type. NOTE : - Warranty certificate to be produced by the contractor from OEM for the following components before processing the bill. (a) For product - 02 Years (b) For metal tank 07 years.

Supply and fixing in repair of sheet metal enclosure SP with two pin and earth plug and socket with one single pole, MCB 32 Amps, 'B' curve, 240 volts complete all as specified and directed.

Supply and fixing of temperature resistent SS braided pipe suitable to sustain pressure up to 8 bar not less than 60 Cm long suitable for incoming (Cold water) & out going (Hot Water) connections of Geyser with washer including taking down existing PVC connection etc. complete all as specified and as directed.

Supply and fixing in repair of stop valve 15mm dia, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed.

Material and labour for concealed sub main wiring with two single core FRLSH PVC insulated unsheathed copper conductor cable 4.00 sqmm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 4.00 sqmm, green colour for earth continuity conductor including taking down old unserviceable sub main wiring and making good the disturbed surface complete all as specified and directed. NOTE : - 3 run of cable and 1 run of conduit shall be measured as 1 unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories/fittings.

Material and labour for concealed sub main wiring with two single core FRLSH PVC insulated unsheathed copper conductor cable 6.00 sqmm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 6.00 sqmm, green colour for earth continuity conductor including taking down old unserviceable sub main wiring and making good the disturbed surface complete all as specified and directed. NOTE : - 3 run of cable and 1 run of conduit shall be measured as 1 unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories/fittings.

Supply and fixing in repair bracket for security light made up of 25mm dia, 0.9 metre long GI pipe, light grade, bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts complete all as specified and directed.

Supply and fixing LED security light luminaire 30 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP65 protection, better optics for uniform distribution with multiplte LEDs not less than 2 W eachand having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with Two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down old unserviceable security light fitting of any description and in any position complete all as specified and directed.

Supply and fixing of heavy duty exhaust fan metallic body 300 mm sweep with louvers, electric, single phase 1400RPM, 240 volt 50 Hz complete and making suitable hole in existing cement concrete / brick walls built in cement mortar 1:4 and removing unserviceable/loose/broken debris upto 500m distance and making good the disturbed surfaces to match with the existing surface including plastering as required & finishes including grouting four Nos rag bolts, nuts & washers and connecting with 3 core copper flexible cable of size 23/0.0076 including testing & commissioning after installation at site complete all as directed.

Supply, laying and testing of cable XLPE insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross-sectional area of size 25 Sqmm 4 core including dismantling existing any type and any size cable complete all as specified and directed.

Supply and fixing in repair of GI protection pipe of 40mm dia light grade for cable protection including all fittings laid in trenches or fixed on pole, complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation, shafts, man holes, laying of cable etc not exceeding 10 Square metre on plan and getting out in soft/loose soil complete all as specified and directed.

Returning filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick each after the cable have been laid tested complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 50 mtrs & depositing where directed at a level not exceeding 1.5 mtrs above the starting point complete all as specified and directed.

Material and labour for supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. NOTE: - Punned thickness shall be measurement & paid.

Material and labour for brick protection covers over cable using sub class B old size brick complete all as specified and directed.

Taking out of unserviceable earthing and material and labour for earthing and material & labour for earthing with galvanised steel earth plate electrode 60cm x 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using galvanised iron wire 4 mm as earthing lead (upto terminal point) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel , wire mesh, 50 mm thick precast RCC 1:2:4 type B1using 20 mm graded stone aggregate , reinforced with 8 mm dia dedormed /TMT bars 3 nos both way 12 mm dia round bar handle and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 of SSR 2009 (Part-I) complete all as specified and as directed. Note :- (i) Earth lead wire and its protection pipe upto and including 7.50 mtr only from top of earth electrode are included under this item. (ii) On testing if the earth resistance is not obtained within permissible limit, earthing will be re-done at NO extra cost ,till the desired earth resistance is obtained. (iii) Any joint in earth lead from earth electrode to test point shall not be allowed/permitted.

Dismantling and taking down ceiling fan any type and capacity cleaning and keeping in safe custody for re-use incl refixing after rewiring all as directed.

Material and labour for hanging only ceiling fan (taking down for repair work) including provision of cable from ceiling rose after servicing and painting with synthetic enamel paint by sparying including filling cavities with filler, one coat after cleaning all dust all as specified and directed.

NOTE:- Amount of credit of Rs. 42,671.00 for retrieved materials is mentioned in Schedule of Credit Page No 19 & 20 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Gupta Enterprises

power house batteries

peeyush construction and engineering co

Ashwani Kumar

Baggay construction Company