Interior Fit-Out Works of 3 nos. SIDBI Branch Offices (2 nos. BOs and 1 nos. EBOs) in South Zone covering Tamil Nadu

Total Amount DSR &

Sr.No Description DSR Amount Non- DSR Amount

Total (DSR +MR) BOQ Amount 1,35,63,688.00

Total cost (i/c GST) 1,35,63,688.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

CIVIL & INTERIOR WORKS

Dismantling tile work in floors , Wall and roofs laid in cement mortar including

stacking material within 50 metres lead.

15.23.2 For thickness of tiles above 25 mm and up to 40 mm SQM 10 113.55 1135.50

Demolishing brick work manually / by mechanical means including stacking of

1.2 15.7 serviceable material and disposal of unserviceable material within 50 metres lead

as per direction of Engineer-in-Charge.

15.7.4 In cement mortar Cum 3 2060.20 6180.60

Carriage of material by mechanical transport including loading unloading and

1.1.1 Lime, murrum, building rubbish

2 MASONRY AND PLASTER

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

2.1 11.3 aggregate) finished with a floating coat of neat cement, including cement slurry,

but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 10 614.20 6142.00

CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick

2.5 13.4 12 mm cement plaster of mix

13.4.1 1:4 (1 cement: 4 coarse sand) SQM 12 357.35 4288.20

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick

2.6 MR POP Punning over cement plaster in line & plumb finished smooth to receive SQM 40 301.33 12053.05

paint. (Internal surfaces of walls).

3 FLOORING WORKS

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron

3.01 MR anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed to conceal screws. metre 140 325.00 45500.00

Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Supplying and fixing of 3mm Luxury vinyl flooring Top layer of approved design & Pattern

as per architects approval & Instructions

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon

loop pile carpet tiles/Plank. The carpet shall have sufficient gauge (1/10 ~ 1/12) with

sufficient stitches (10~13) per inch. The carpet shall be solution dyed fibre content or with

injection printing technology. The carpet shall have the pile height ranging from (2.0 ~

3.0) mm with average density higher than 4500 Oz/ cubic yard. The total thickness

of the carpet tile shall also range from (5.5 ~ 6.0) mm.

4 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including

providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per

IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges

of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling

section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm

each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter

channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm

centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum

board to ceiling section and perimeter channel with the help of dry wall screws of size

3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered

and square edges of the board with recommended jointing compound , jointing tapes

, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint

and two coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but excluding the cost of

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing & fixing of Silhoutee Frame ceiling tile in size 600x600x15mm having noise

reduction co-efficient of 0.7, Density of 100 kg / m3, and Humidity resistance of 95% to be

4.02 MR laid on exposed grid system with white wrap comprising main runner 3.00 mm x 24mm sq m 115 2450.00 281750.00

web height cross tee 1.2 mtrs x 24 mm web height and 0.6 mtrs x 24 mm web height. The

wall angle shall be 3.0 mtrs.

5 PARTITIONS AND WALL CLADDING

WALL PANELING :-Providing and fixing Paneling upto ceiling height consisting of

Aluminium frame and required board, frame work made of Aluminium section made of

50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges of

25 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre

to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48 mm wide having one

flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to

centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of

5.01 MR partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs

at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work

by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300

mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick

having two flanges of 9.5 mm each) to be provided at the horizontal joints of two

boards, fixed to the studs using metal to metal flat head screws, including jointing

and finishing to a flush finish with recommended jointing compound, jointing tape, angle

beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as per manufacture's

specification and direction of engineer in charge all complete.

Paneling with 11- 12 mm thick HDHMR board to IS: 5509 sq m 74 2414.28 178656.72

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of

Aluminium frame and required board, frame work made of Aluminium section made of

50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges of

25 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre

to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48 mm wide having one

flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to

centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of

5.02 MR partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs

at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work

by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300

mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick

having two flanges of 9.5 mm each) to be provided at the horizontal joints of two

boards, fixed to the studs using metal to metal flat head screws, including jointing

and finishing to a flush finish with recommended jointing compound, jointing tape, angle

beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as per manufacture's

specification and direction of engineer in charge all complete.

Both side 12 mm thick HDHMR board to IS: 5509 sq m 230 3450.00 793500.00

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF, on an existing

Plywood surface.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved

brand and manufacture, including providing and fixing top & bottom pivot & double

5.04 21.18 acting hydraulic floor spring type fixing arrangement and making necessary holes etc. sq m 26 5325.90 138473.40

for fixing required door fittings, all complete as per direction of Engineer in charge (Door

handle, lock and stopper etc. to be paid separately)

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing and fixing partition comprising 12 mm thick clear toughened safety glass of

approved make conforming to IS 2553 (Part-I) and IS 14900, fixed in anodized aluminium

U-channels of approved size and section at top, bottom and sides as required. The work

MR shall include machine polished exposed edges of glass, neoprene packing, EPDM sq m 50 3560.00 178000.00

gaskets, silicone sealant, aluminium channels, screws, fasteners, anchoring

arrangements, cutting, handling, transportation, installation, cleaning and all incidental

works complete as per approved drawings and direction of Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames,

5.05 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood cum 0.60 142949.70 85769.82

Providing and fixing partition top beading 80x12 mm, including cutting, shaping,

adhesive/fastener fixing, edge finishing, surface preparation, and applying polish with

matching finish, complete in all respects as per site requirement and engineer-in-charge

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool

conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G

Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in

position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood

and well matched commercial 3 ply veneering with vertical grains or cross bands and

face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sq m 24 2392.65 57423.60

Providing and applying panelling/partition with matching colour groove finish and

polishing, including all materials, labour, surface preparation, fixing accessories, edge

finishing, sanding, colour matching, groove cutting, polishing coats, and complete

finishing as per site requirement and engineer-in-charge directions.

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised

5.11 9.97 (anodic AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade,

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door

stopper with necessary screws, etc. complete.

Door Closers: Providing and fixing aluminium extruded section body tubular type

universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the

body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with

double speed adjustment with necessary accessories and screws etc. complete.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123

5.14 MR with Roses & Escutcheon in SS packaged with Mortice lockset 55mm backset, 20 SS EACH 15 2650.00 39750.00

forend, SS strike plate and EP Cylinder for all flush doors.

Providing and fixing 600 mmx25 mm H Type handle for Doors approved make and

designs as per engineer in charge

Providing and fixing minimium 70-90 kg capacity flooor spring for Doors approved make

and designs as per engineer in charge

Providing and fixing Glass door lock approved make and designs as per engineer in

5.18 MR Providing and fixing Glass Big -L approved make and designs as per engineer in charge each 6 2450.00 14700.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered

surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC

(Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and

manufacture, including applying additional coats wherever required to achieve even

shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC

content less than 50 grams/ litre

Painting with synthetic enamel paint of approved brand and manufacture of required

colour to give an even shade :

13.99.1 One or more coats on old work. sq m 190 102.80 19532.00

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

BLINDS Providing & supplying of Window Blinds as per the approved sample in

required shade and style consisting, of ZEBRA BLINDS comprising of optima screen Fabric

comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m,

Thickness 0.67 mm, Yarn count 18- 19/cm, having fire resistance standard – NFPA 701-89

small testing ISO- 5659-2 .Thetear resistance should be complying to ISO4674 & breaking

resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe

installation, moulded plastic with steel spring support and inserted into the tube end. It

shall be driven by a ball chain pulley with ball chain and can be positioned at right side

or left hand side of the Shade. The Shade when lowering or raising, shall be

automatically locked in position upon release of the ball chain by means of a built in

friction lock.Universal clutch for left and right hand operation.Chain Gear Ratio of 1.75:1.

The END PLUG shall be molded of plastic witha steel location pin.The plug shall be

inserted into the tube end.(Opposite to the Drive Unit) for ease of installation. The

SUPPORT BRACKETS shall be of coated steel & provided with covers and used in right

M.R. hand or left hand positions differentiated by the acceptance of the of the rectangular Sqm 45 2,450.00 110250.00

drive unit support or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling

Mount (c) On Frame

(d) in Recess. The Bracket should be protruding outside maximum of

80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter &

skin thickness of 1mm and shall incorporate a key way integral with the tube to

accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom made up of powder

coated steel. The BALL CHAIN shall be 2mm diameter cord with 4.5mm diameter acetal

balls moulded co-axially to it on 6mm pitch to form an endless ball chain. It is used for

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface as

approval of the Architect. (Only film surface area shall be measured and paid).

Providing & fixing Sidbi Signages & Logo & Sidbi Enviremoent Theme as per Direction of

Engineer in Charge

Providing & fixing Sidbi Sign Glow Board For Exterior Acrylic Base Embeded Letter as per

design (Front approx = 21 x 4)

Providing and fixing sandwich poster made of printed graphic mounted on required

thickness sunboard/ACP board, fixed directly on wall with SS decorative studs, complete

with all necessary hardware, fitting, and installation at site, as per approved design and

direction of engineer-in-charge.

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting

of G.I. frame and required board, including providing and fixing of frame work

made of special section power pressed/ roll form G.I. sheet with zinc coating

of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel

50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and

ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm

dia meter 50 mm length or suitable anchor fastener or metal screws with nylon

5.32 9.105 plugs and the studs 48 mm wide having one flange of 34 mm and other flange

36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling

channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and

nuts, including fixing of studs along both ends of partition fixed flush to wall with

suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm

centre to centre, and fixing of boards to both side of frame work by 25 mm long

dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to

The boards are to be fixed to the frame work with joints staggered to avoid through

cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm

each) to be provided at the horizontal joints of two boards, fixed to the studs using

metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x

25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per

manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass

Reinforced Gypsum (GRG) plaster board conforming to IS: 2095:

Providing and fixing gypsum board vertical bend in required radius/shape using 12.5mm

5.33 thick gypsum board over GI framework (stud/channel), including cutting, bending, Rmtr 102 195.00 19890.00

fixing, joint treatment with tape and compound, finishing complete in all respect

Total Amount 1237378.37 3421463.39

Total Amount 1237378.37 3421463.39

Add labour cess @0.973 as per CPWD circular 1203969.15

Add CPWD cost index @103 on DSR civil 2023 1240088.23

Total Amount 1240088.23 3421463.39

Total Amount 1240088.23 3421463.39

Total Amount DSR & NDSR 4661551.62

Total Amount DSR & NDSR 4661551.62

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface/

1.10 recessed medium class PVC conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated

A.1 copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point

(without independent switch etc.) with1.5 sq.mm FRLS PVC insulated copper

1.55 conductor single core cable in surface / recessed PVC conduit, and earthing

the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core

cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC conduit

alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core

cable for loop earthing as required.

Supplying and fixing following modular switch/socket on the existing modular

1.24 plate & switch box including connections but excluding modular plate etc. a

1.24.4 3 pin 5/6 amp socket outlet Each 90 136.00 12240.00

1.24.5 6 pin 15/16 amp socket outlet Each 30 219.00 6570.00

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Supplying and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base

& cover plate on existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following

1.14 sizes of FR PVC insulated copper conductor, single core cable in surface/

recessed medium class PVC conduit as required

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 30 482.00 14460.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE

C.1 MR insulated Copper conductor armoured cable of 1.1 KV grade conforming to

IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 45 1300.00 58500.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 6 1800.00 10800.00

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in the

D.2 existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following rating, four pole, 415 volts, isolator in the

2.13 existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/recess, complete with

2.4 tinned copper bus bar, neutral bus bar, earth bar, din bar,

D.4 interconnections, powder painted including earthing etc. as required. (But

without MCB/ RCCB/ Isolator)

Providing and fixing 400mm wall mounted oscillating fan, heavy-duty type,

230V, 50Hz, single phase, with three-speed control regulator, complete with

suitable mounting brackets, clamps, bolts, nuts, and necessary wiring

connections from the nearest point using 1.5 sq.mm copper flexible wire,

including testing and commissioning at site, complete as required.( Make:

Havells/Cromton/Usha/Bajaj asapproved by ingineer-in-charge)

Supplying and fixing of following sizes medium class PVC conduit aong with

1.21 accessories in surface/ recess including cutting the wall and making good the

E.12 same incase of recessed conduit as required

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Supplying and Installation of following size perforated of painting with powder

coating M.S. cable trays of perforation of not more than 17.5% in convinient

sections, joined with connectors suspended from the cieling with MS

suspenders including bolts and nuts painting suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 15 1243.00 18645.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe of 2.7 metre long etc. with

charcoal/coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for

connections etc. As required.

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Online UPS- Input supply: Three Phase, Output supply: Three Phase. Supplying,

installation, Testing & Commissioning of following capacity at full load (Unity

at operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online

double conversion true sine wave Uninterrupted hot swapable (allow for the

replacement or addition of battery modules without shutting down the entire

system) modular Power Supply (UPS) system with N+1 modules (N denotes total

number of modules required for rated capacity). The UPS shall include a

Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH

capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour

backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and

Static Bypass switch along with provision for manual bypass, suitable

isolationtransformer for additional protection against neutral faults etc. UPS

shall have inbuilt phase sequence correction. The UPS systems offered are to

26.2.1 be of the latest technology with Digital Control Microprocessor based for 190 Nos 3 208893.00 626679.00

DELHI SCHEDULE OF RATES (E&M)-2025reliable operation using Insulated Gate

Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM

(Pulse Width Modulation). The quality of design, manufacturing and inspection

process should confirm to the relevant Inter-national standards such as

IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while

operating on battery mode and delivering quality power to the 100% non-

linear loads. Current total harmonic effect(ITHD) on the input grid shall be <

5% at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters

shall be included in UPS cost), extreme power factor kit to be included to limit

the input power factor (PF) to 0.99 and output power factor shall be unity (i.e.

kw rating of the UPS shall

be kva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to

0.7 leading power factor loads. UPS shall be suitable for incoming supply AC :

3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz

Providing & Fixing exhaust fan of approved make and size complete with

frame, mounting arrangement, necessary wiring connection from nearby

point, screws, fasteners, cutting/fitting work and testing & commissioning

complete as required at site

Total of Electrical items 2078010.00 117750.00

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Total Amount 2078010.00 117750.00

Total Amount 2078010.00 117750.00

Total DSR+NDSR 2195760.00

Digitally signed by MANISH

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

2025 Amount (A)

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling /heating having

100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two

compressors (with individual separate PCB) for above 14HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent,

vibration Isolators with suitable foundation etc. complete as required. To have better

efficiency condenser fan shall be capable to operate at different speed with respect to load.

The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD

Specifications and work even at 50°C ambient temperature without tripping. The system shall

31.3 be able to deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable

to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall

be filled with first charge of the refrigerant and ready for use as required. The condenser

should be coated with a hydrophilic film to prevent water accumulation on the surface of the

heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby

improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio

(ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC)

2024 as below and complete as per CPWD specification, connections, inter connections etc.

as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70

ISEER 7.6 for Super ECSBC Building)

2.0 INDOOR UNIT

Supply, Installation, Testing and Commissioning of following minimum capacity 4 way

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre- filter,

fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section

with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary

supports, vibration Isolation, Corded remote control etc., suitable for operation on single

phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down

upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to

adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will

be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be

same as of Outdoor)

Digitally signed by MANISH

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

2025 Amount (A)

Supply, Installation, Testing and Commissioning of following minimum capacity High wall

type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain

pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC

supply, complete as required. The Indoor units must shut down upon receiving a singal from the

BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions

of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of

REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing

of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

3 31.14.1 6.4 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 180 256.00 46080.00

3.1 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 180 346.00 62280.00

3.2 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 120 487.00 58440.00

3.3 31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 90 615.00 55350.00

3.4 31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 60 739.00 44340.00

3.5 31.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 45 1157.00 52065.00

3.6 31.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 24 1286.00 30864.00

3.7 31.13.1 Indoor Units (y-joint) Each 18 4535.00 81630.00

4 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe, complete with fittings, supports, U

trap arrangement, Clean Plug with 6mm nitrile insulation and accessories as per specifications,

Digitally signed by MANISH

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

2025 Amount (A)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses

etc.,including cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer, including welding and bolted with special shaped washers etc.

10.16.1 Hot finished welded type tubes kg 150 194.40 29160.00

Supplying and fixing following rating, double pole,(single phase and neutral), 240 V,

residual current circuit breaker (RCCB), having a sensitivity current 30

mA in the existing MCB DB complete with connections, testing and commissioning etc.

Total Amount 21,02,085.00

Total Amount 21,02,085.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate DSR Amount

A. 2025 UTP Components for Data

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper

cable in existing conduit/ on surface, U/FTP, LSZH, Non-

Plenum, Horizontal (solid) Cable suitable for high speed data networking application

supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP)

1 1.53 cable with color coded insulation

for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1,

Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE

802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2

mm. Cable should have been tested and verified by UL/ ETL etc. complete as required.

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination at Rack

Side. Keystone Unshielded Outlet, 180DG C6, Blue

Supply, Installtion, Testing and Comissioning of I/O port for CAT6 cable termination at Rack

Side end Redantant . Keystone Unshielded Outlet, 180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

4 MR information outlet (I/O) to end user Redantant device connectivity.High Speed Gigabit Nos. 56 420.00 23520.00

24AWG U/UTP Patch Cord Blue, LSZH, C6, 2M (Blue)

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

5 MR information outlet (I/O) to Rack End Redantant device connectivity.High Speed Gigabit Nos. 56 420.00 23520.00

24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow)

Supply, Installtion, Testing and Comissioning of 24 port Loaded Angled Staggred Jack Panel

for CAT6 cable termination at rack end. Data Active Redandant

Supply , Installtion , Testing and Comissioning of 2 Port British Style Shuttered Face Plate white for I/O

fixing at user side

8 MR SITC of 04 core OM3 Multimode fiber orange color 50/125, minimum bending radius 15x OD RM 85 229.17 19479.17

Digitally signed by MANISH

SITC of 24U Floor Standing Network Rack, of suitable standard dimensions as per site and

Engineer In charge direction, complete with 19-inch mounting frame, minimum 24U usable

height, front toughened glass/acrylic lockable door, lockable rear door/panel, removable

and lockable side panels, cable entry provisions at top and bottom, adequate ventilation

with provision for fan mounting, adjustable mounting rails, equipment mounting hardware,

earthing provision, and all necessary accessories including fixing hardware, cable

management, and installation complete in all respects as required for housing active and

passive networking equipment, including testing and commissioning.

Supply, Installation, Testing & Commissioning of 24-Port Layer-2 Managed Gigabit Ethernet

Switch comprising 24 × 10/100/1000 Mbps RJ45 ports and 4 × Gigabit SFP uplink ports,

switching capacity not less than 56 Gbps, forwarding rate not less than 41.7 Mpps,

supporting IEEE 802.3, 802.3u, 802.3ab, VLAN (802.1Q), QoS, STP/RSTP/MSTP, IGMP Snooping,

Link Aggregation (LACP), Port Mirroring, DHCP Snooping, Access Control List (ACL), Jumbo

Frames, rack-mountable, complete with power cord, rack mounting accessories,

configuration, testing and commissioning, suitable for structured cabling and LAN

Total Amount 185000.00 248813.17

Total Amount 185000.00 248813.17

Total Amount DSR & NDSR 433813.17

Total Amount DSR & NDSR 433813.17

Digitally signed by MANISH

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No 2025/ DESCRIPTION QTY UNIT RATE

AMOUNT AMOUNT (A)

DSR (INR) NON-DSR

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

27.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the

1 wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel

paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

27.21 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

27.21.1 Pendant type 26 Each 599.00 15574.00

Supplying, fixing, testing and commissioning of butterfly

valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required :

Digitally signed by MANISH

Carefully Extending, lowering and repositioning the existing

sprinkler points from the existing fire fighting sprinkler piping

network to suit the revised false ceiling layout, including

providing and fixing required lengths of GI/MS sprinkler

drop pipes (up to 1.5 m average), fittings, socket, nipple,

reducer, clamps, hangers, cutting and threading, refixing

existing sprinkler heads, alignment with ceiling tiles, testing,

commissioning and making the system operational

complete as required and as directed by Engineer-in-

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with

maximum working pressure of 175 PSI test pressure of

27.25 875 PSI (Burst) with branch line (Inlet) 25mm NPT

5 male thread to sprinkler head (Outlet) 15mm NPT

female thread with reducer, nipple, 2 side brackets,

center bracket, stockbar of following sizes

complete as required.

Providing and fixing ISI Marked of approved make Fire

6 Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 3 NOS 12000.00 36000.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Digitally signed by MANISH

Total Amount 330041.00

Total Amount 330041.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - CCTV

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

A. CCTV DSR NDSR

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265 Vandal Proof

Dome camera with 2.8 to 12mm Motorised Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise

1 MR Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple streams,3-Axis, Nos 12 7500.00 90000.00

IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with

IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection

Supply, Installation, Testing & Commissioning of Linux-based Network Video

Recorder (NVR) for centralized monitoring, management and recording of

IP cameras from the Control Room, supporting minimum 08 IP camera

channels, with minimum 256 Mbps incoming bandwidth,

H.265+/H.265/H.264 video compression, minimum 02 SATA interfaces for

2 MR HDD, minimum 16 alarm inputs and 04 alarm outputs, 1.5U, 19-inch rack- Nos 3 11500.00 34500.00

mountable chassis, with HDMI/VGA video output, network interface and

USB ports, complete with compatible IP PTZ joystick controller for camera

selection, pan/tilt/zoom and focus control, power supply, required

accessories, configuration, installation, testing and commissioning,

complete in all respects. HDD shall be provided separately.

Supply, Installation, Testing & Commissioning of 4 TB Surveillance Grade

SATA Hard Disk Drive (HDD), 3.5-inch form factor, 7200/5400 RPM as per

manufacturer design, SATA III (6 Gb/s), specifically designed for 24×7 CCTV

3 MR surveillance applications, compatible with Network Video Recorder (NVR), Nos 3 12900.00 38700.00

complete with mounting, formatting, configuration, testing and

commissioning. Approved makes: Western Digital Purple, Seagate SkyHawk,

Toshiba S300 or equivalent.

Digitally signed by MANISH

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

Supply Installation Testing & Commissioning of “24-inch or higher Full HD

LED Monitor, minimum resolution 1920 × 1080, LED-backlit display, 16:9

aspect ratio, minimum brightness 250 nits, minimum contrast ratio 1000:1,

4 MR response time ≤5 ms, refresh rate ≥60 Hz, with HDMI and VGA or equivalent Nos. 3 15000.00 45000.00

digital/analog input interfaces, complete with compatible wall-mount

bracket/clamps and desk-mounting stand, power/data cables and all

necessary accessories for installation, testing and commissioning.

5 MR SITC of HDMI cables 10 meters M2M etc all compelte. Nos 3 3500.00 10500.00

Supply, Installation, Testing & Commissioning of 8-Port Gigabit Managed PoE

Switch comprising 8 × 10/100/1000 Mbps RJ45 PoE ports conforming to IEEE

802.3af/at standards, with minimum 120 W total PoE power budget, and 2 ×

Gigabit SFP/RJ45 uplink ports, switching capacity minimum 20 Gbps,

6 MR forwarding rate minimum 14.8 Mpps, supporting VLAN, QoS, STP/RSTP, IGMP Nos 3 12300.00 36900.00

Snooping, port isolation and surge protection, rack/wall mountable,

complete with power cord, mounting accessories, configuration, testing

and commissioning, suitable for IP CCTV applications, complete in all

Total : A - CCTV 0.00 255600.00

Total Amount 0.00 255600.00

Total Amount 0.00 255600.00

Total Amount DSR & NDSR 255600.00

Total Amount DSR & NDSR 255600.00

Digitally signed by MANISH

FIRE ALARM SYSTEM WORKS

S.NO. DESCRIPTION UNIT Qty RATE Amount

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning sector panel suitable for following

zones, complete with visual indications for short circuit fault, open circuit fault, fire

a) 28.1.9 condition and all other standard facilities as per IS:2189 with mimic diagram

for all area/zone covered, complete with all connections, interconnections as

Supplying, installation, testing & commissioning of smoke detector with built in LED

and Mounting base complete withb all Connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS

28.1.3 construction in Surface/ Recess with Stainless Steel chain & hammer Assembly Each 6 513.00 3078.00

complete with glass and push button etc. as Required.

Supplying, installation, testing & commissioning of response indicator on

d) 28.1.5 surface/recessed MS Box having two LED, metallic cover complete with all Each 15 222.00 3330.00

connections etc as required.

Supplying, installation, testing & commissioning of Fire alarm Sounder with Facility

to make annoucement, mountedc in M.S Box (16 SWG) with Hinged cover plate &

Suitable for operation with Amplifier i/c line matching transformer etc complete as

Supply, Installation, Testing & Commissioning of LED Exit Signage, Single Side,

3W–5W, wall mounted, 230V AC, inbuilt Li-ion/Ni-Cd battery backup (minimum 180

minutes), complete with fixing accessories and connection from nearest lighting

CABLING & WIRING

Digitally signed by MANISH

S.NO. DESCRIPTION UNIT Qty RATE Amount

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

600/1000V rated with annealed copper conductor having

XLPE insulation, steel wire armouring & FRLS/HFFR outer

sheath complete as required.

Total Amount 202415.00 41250.00

Total Amount 202415.00 41250.00

Total Amount DSR & NDSR 243665.00

Total Amount DSR & NDSR 243665.00

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

BO Incharge The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x 675mm(H) . Side

1 storage having a provision for three equal drawer unit and two openable shutter & one open storage Nos 3 45500.00 136500.00

with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest

all storage to be made out of 18mm thick pre laminated particle board. Provision of Junction box, wire

raceway and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension

(L)2100mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D) 400mm X (H)

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non working

2 Back Storage edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage Dimension Nos 3 23500.00 70500.00

Supplying and placing in position of 360 degrees revolving high back chai. The chair of Size :-

(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

BO High Back with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for

Chair extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

BO Visitor Back Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

4 Base:Cantilever Frame, Base Type: Cantilever, Maximum Seating Height:19".The Seat & back are made Nos 9 9500.00 85500.00

up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as per

requirement, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern,

2 seater sofa BO Texture:Two Tone. steam beech solid wood have used for framing construction of sofa .The seat

5 Cabin/ cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 Nos 5 30000.00 150000.00

Reception inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The

backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

BO Incharge The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x 675mm(H) . Side

1 storage having a provision for three equal drawer unit and two openable shutter & one open storage Nos 3 45500.00 136500.00

with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest

all storage to be made out of 18mm thick pre laminated particle board. Provision of Junction box, wire

raceway and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension

(L)2100mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D) 400mm X (H)

Providing, supplying and placing in position 3-Seater Sofa, modern design, overall size approximately

2000 mm (L) × 750 mm (D) × 710 mm (H) with seating height approximately 410 mm, having frame

made of seasoned Steam Beech solid wood, upholstered with premium-quality Leatherette of approved

colour, shade and texture. Seat cushion shall comprise multi-layered foam of density 32–35 kg/m³ with

3 seater sofa BO 2.75" and 1.75" elastic webbing support, and backrest shall comprise 28 kg/m³ foam with 200 GSM

6 Cabin/ polyester polyfill. Upholstery shall be stitched using bonded nylon thread and provided with stainless Nos 3 42000.00 126000.00

Reception steel legs in matte finish. The sofa shall be complete in all respects including all materials, hardware,

fixing accessories, transportation, loading/unloading and placement at site, as per approved

sample/design and instructions of Engineer-in-Charge.

BO Cabin/ Supplying, and placing in position of Cofee/ Corner Table as per approved design Dimension(L)450mm

Reception X (D)450mm X (H)450mm

Supplying, and placing in position of Centre Table as per approved design Dimension(L)1150mm X

8 Centre Table Nos 3 16500.00 49500.00

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

AGM/Manager The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x 675mm(H) . Side

9 storage having a provision for three equal drawer unit and two openable shutter & one open storage Nos 3 38790.00 116370.00

with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest

all storage to be made out of 18mm thick pre laminated particle board. Provision of Junction box, wire

raceway and 6 module fliptop box for wire passing or as per site requirement. Main Table Dimension

(L)1500mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D) 400mm X (H)

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

BO Incharge The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x 675mm(H) . Side

1 storage having a provision for three equal drawer unit and two openable shutter & one open storage Nos 3 45500.00 136500.00

with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest

all storage to be made out of 18mm thick pre laminated particle board. Provision of Junction box, wire

raceway and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension

(L)2100mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D) 400mm X (H)

Supplying and placing in position of 360 degrees revolving high back chai. The chair of Size :-

(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

10 AGM Chair with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for Nos 2 10500.00 21000.00

extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

AGM Visitor Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

11 Base:Cantilever Frame, Base Type: Cantilever, Maximum Seating Height:19".The Seat & back are made Nos 6 9500.00 57000.00

up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non working

12 Back Storage edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage Dimension Nos 4 23500.00 94000.00

Supplying and placing in position of conference table of required size as per image/ Layout drawing. The

work surface top should be of thickness 42mm top prelaminated particle board with 2mm thick PVC

Conference edge banding. The side panel are made up of 36mm thick prelaminated particle & modesty panel are

13 made out of 25mm thick prelaminated particle board with 2mm thick PVC edge banding. The wire carrier Nos 2 48500.00 97000.00

should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a provision of 6

module flip top box & metal raceway for wire flow.

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

BO Incharge The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x 675mm(H) . Side

1 storage having a provision for three equal drawer unit and two openable shutter & one open storage Nos 3 45500.00 136500.00

with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest

all storage to be made out of 18mm thick pre laminated particle board. Provision of Junction box, wire

raceway and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension

(L)2100mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D) 400mm X (H)

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood

and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

Confrence high tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/-

14 0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall Nos 2 10500.00 21000.00

be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The

backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

Medium Back lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

15 chair Confrence with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall Nos 16 9500.00 152000.00

room have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg /m3)

The backrest has a foam of 28kg/m3.

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk PVC

edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm x

25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel fixed

on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron below top for

wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non- sharing

16 workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of glass divider Nos 13 24500.00 318500.00

rest on the "D" brackets on the table top between opposite seatings. All working or non working edges

shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2

drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

BO Incharge The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x 675mm(H) . Side

1 storage having a provision for three equal drawer unit and two openable shutter & one open storage Nos 3 45500.00 136500.00

with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest

all storage to be made out of 18mm thick pre laminated particle board. Provision of Junction box, wire

raceway and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension

(L)2100mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D) 400mm X (H)

Providing and fixing printer table of size 1500 mm × 750 mm (5' × 2.5') made from 18 mm thick pre-

laminated particle board (both side laminated) of approved shade and make, including top, sides,

17 Printer Table modesty panel, shelves as required, edge banding with 2 mm PVC edge tape on exposed edges, Nos 3 11500.00 34500.00

necessary screws, fittings, hardware, level adjustment arrangement, labour, handling, transportation

and complete installation as per approved design and direction of Engineer-in-Charge.

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side Top

with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht. 1200mm,

Double Raceway systems Skirting label and below the table top . lower tile both side laminated and

Modular upper tile inside side fabric, White Board and white Tinted Glass . With Side Top Size 900W x 400D x

18 750H 25mm thick Gabel end 18mm thick MDF board., and 3Drawer top supported Pedestal unit Nos 11 38000.00 418000.00

Size 400W x 400D x 725H made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty

White, Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-

Munshel Gray. and White Tinted Glass

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

19 Workstation/ Nos 26 8500.00 221000.00

with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of

density 30-35 (+/- 2kg /m3) The backrest has a foam of 28kg/m3.

Providing & Installation of Pantry table of size 1.2m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

20 Pantry Table Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above Nos 3 24500.00 73500.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing & Installation of Reception table of size .75Dia X 0.75m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

21 Reception Table Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above Nos 3 26500.00 79500.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC

22 Pantry chairs Nos 11 3700.00 40700.00

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

BO Incharge The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x 675mm(H) . Side

1 storage having a provision for three equal drawer unit and two openable shutter & one open storage Nos 3 45500.00 136500.00

with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest

all storage to be made out of 18mm thick pre laminated particle board. Provision of Junction box, wire

raceway and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension

(L)2100mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D) 400mm X (H)

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made

Openable of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided with machine

Shutter storage pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle

and suitable lock. All exposed area PVC edge lipping

Size as decided by site engineer/Bank Sqm 24 18500.00 444000.00

Pantry Under Counter Storage, made with HDHMR board finished with laminate on all exposed surfaces.

Unit depth: 600mm. All edges shall be finished with matching edge banding. Includes shutters, shelves,

hardware (hinges, handles), and necessary fittings complete in all respects.

Pantry/ Pantry Overhead Storage Unit, made from HDHMR board of approved shade and grade conforming to E1

Workstation norms, with unit depth of 400mm. All exposed edges finished with 2mm PVC edge banding using

Overhead hotmelt EVA glue. Includes shutters, shelves, and necessary hardware and fittings, complete in all

Storage respects.

3 Drawer top supported pedestal unit size 400W X 400D X 725 H made in 18mm thick complete made in

26 Mobile Vanity MDF board. Nos 5 8800.00 44000.00

Total Amount for Furniture 3061570.00

Total Amount for Furniture 3061570.00

Digitally signed by MANISH

S.No Description Unit Qty. Rate Amount

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying, Installation, Testing &

Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with

Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -50C to

400C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,

UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry),

of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K /

1 8.1 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not

more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/

Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5

sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5

year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all testing

required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of

Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to

40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80,

UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry),

of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K

/6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not

more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year

OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-inCharge as per

requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not

rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Total Cost of Light items 279602.00

Digitally signed by MANISH