Loading…
Loading…
Tender Value
₹16.8 L
EMD Value
₹17,000
Closing Date
2 Jul 2026, 6:00 pm7d left
Similar tender results from the same govt authority in the past 3 years.
Executive Engineer, Panchayat R&B Dn. Gandhinagar
Addition, Alteration & Repairing of Rest House at Sadra Under CDP 3 2025-26 Ta. Gandhiagar Dist. Gandhiagar.
317206
04 of 2026-27/10
Open
Civil - All
Gandhinagar
7 documents required · 7 mandatory
₹900
Executive Engineer Panchayat (R & B) Division, Gandhinagar
₹17,000
24 Jun 2026
24 Jun 2026
24 Jun 2026
2 Jul 2026
24 Jun 2026
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Removing and scraping of old deteriorated
plaster of any thickness fromm wall / R.C.C
1 member including stacking of serviceable 748.000 Sqm. 19.57
material and disposal of unserviceable from
site of work with all lead and lift
Dismentaling tiled of stone floors laid in
mortar including stacking of serviceable
materilas and disposal of unserviceable
materials with all lead and lift.
Excavation for foundation upto 1.5 m depth
including sorting out and stacking of
3 useful materials and disposing off the 60.00 Cum. 117.26
excavated stuff upto 50 Meter lead.(A) Loose
or soft soil
Excavation for foundation for depth from
m to 3.0 m including sorting out and
4 stacking of useful materials and disposing 8.00 Cum. 162.38
off the excavated stuff upto 50 Meter
lead.(B) Dense or Hard soil
Filling available excavated earth excluding
rock in trenches plinth side of foundation etc.
5 in layer not exceeding 20cm. In depth 47.60 Cum 130.39
consolidation each deposited layer by
ramming and watering.
Filling foundation and plinth with murrum or
includind watering, ramming and consolidating
etc. comp.
Providing and laying cement concrete 1:2:4 (1-
Cement : 2- Coarse sand : 4- graded stone
7 aggregates 20 mm nominal size) and curing 4.00 Cum 3653.07
complete excluding cost of formwork in (A)
Foundation and Plinth
Providing and laying nominal cement concrete
M-200 in R. C. C. 1:1 1/2 :3 (1 cement : 1 1/2
coarse sand : 3 graded stone aggregate
mm. Nominal size) and curing complete
including the cost of form work but excluding
the cost of reinforcement for R.C.C. work in
foundation footing base of column & mass
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Providing and laying nominal cement concrete
M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2
coarse sand : 3 graded stone agregate
mm. Nominal size) including finishing smooth
with curing complete including the cost of form
work but excluding the cost of reinforcement
for R.C.C. work in column Upto ground level.
Providing & laying cement concrete 1: 3 : 6 (
Cement : 3 Coarse sand : 6 graded B.T stone
10 aggregate 20mm nominal size) Curing comp. 14.00 Cum 3292.84
including cost of form work in foundation and
Providing and laying nominal cement concrete
M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2
coarse sand : 3 graded stone agregate
mm. Nominal size) including finishing smooth
with curing complete including the cost of form
work but excluding the cost of reinforcement
for R.C.C. work in column for ground Floor
Providing and laying nominal cement concrete
M-150 in R.C.C. 1:2 :4 (1 cement :2 coarse
sand : 4 graded stone agregate 20 mm.
12 Nominal size) including finishing smooth with 15.00 Cum 4790.76
curing complete including the cost of form
work but excluding the cost of reinforcement
for R.C.C. work copping
Providing and laying nominal cement concrete
M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2
coarse sand : 3 graded stone agregate
mm. Nominal size) including finishing smooth
with curing complete including the cost of form
work but excluding the cost of reinforcement
for R.C.C in slabs for Ground Floor.
Providing TMT Bar FE 500/500D
reinforcement for R.C.C. work including
bending, binding and placing in position
complete upto floor two level.
Brick work using common burnt clay building
bricks having crushing strength not less than
15 35 Kg./Sq.m. in foundation and plinth in 26.00 Cum 4020.80
cement mortar 1:6 (1 cement:6 fine sand) (b)
Conventional.
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Brick work using common burnt clay building
bricks having crushing strength not less than
35 Kg./ Sqm. in cement mortar 1:6 ( 1 cement
: 6 Fine sand ) in super structure above plinth
level upto floor two level ( for G.F )
Conventional
Half brick masonary in common burnt clay
building bricks having crushing strength not
less than 35kg./sq.cm. in cement mortar 1:3 (1
cement : 3 coarse sand ) with 2nos. of 6mm
dia mild steel round bars every three coarse
embedded in cement mortar in superstructure
for Ground floor (Conventional)
Providing and fixing FRP frame size 100x50
mm and 28mm thick FRP depress panel
shutter having extra reinforcement on sides &
edges in Gel coat finish. The core of the
shutter & frame is to be filed up with injected
fire retardant grade polyurethene foam done
in situ alongwith embedded wooden pieces for
stiffening & also taking hinges & fintures. The
whole FRP frame & shutter is to be water
proof weather proof, termite proof &
resistance to mild acid/alkali. Rates are to be
inclusive of S.S hinges with necessary screws
& alluminium fixtures & fastenings & fastener
Providing and fixing standared extruded of
alluminium section of size 63mm x 38.10mm x
1.2mm (Jindal Section :2434, @ Wt.
Kg/mt) with colour anodized alluminium frame
for ventilation with 5 mm thick frosted glass
19 as details etc complete for Ventilation {Colour 1.10 Sqm 1301.82
as directed by Engineer in charge except
black & Alluminum section shall be Jindal or
equivalent brand and glass of Modiguard, AIS
or equivalent brand}
Providing and fixing Safty grills of required
pattern for windows Rectangular CRC pipes
of size 50 x 30 x 2mm at required spacing as
20 per design including fixing rat mesh and hold 217.00 Kgs. 107.26
fasting with coach bolts including one coat of
primer and two coats of mattfinished oil
painting etc complete.
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Providing and laying Machine cut, Free edges,
Machine polished Telephone Black Madras
Granite stone slab 18 mm (Average) thick
{Single piece not more than 150 cm } for stair
steps and riser as per design incl. full moulded
21 round front edge & 1 cm nosing & necessary 5.00 Sqm 3168.37
groobe on trade of steps laid on 20 mm thick
cement mortar 1:6 (1 -cement : 6 coarse
sand ) jointed with grey cement slurry
including rubbing and polishing etc. complete
Providing and laying Ceramic tiles 6mm thick
in flooring treads of steps and landing laid on
22 a bed of 12mm thick cement mortar 1:3 (1- 17.00 Sqm 970.07
cement : 3-coarse sand ) finishing with flush
pointing in white cement.
Providing and laying coloured glazed tiles of
the size 300 mm x 200 mm x 8 mm / 300 mm
x 450 mm x 8 mm in skirting, risers of steps
and dedo on 10 mm. thick cement plaster 1:3
(1 cement : 3 coarse sand) & jointed with
white cement slurry.
Providing 15mm thick cement plaster ( Mala
Trowel finish) in Single coat on brick/concrete
walls for interior plastering upto floor two level
24 and finished even and smooth in (i) Cement 752.00 Sqm 205.37
mortar 1:4 (1-cement:4-sand) including
finishing coat of neat cement slurry for Ground
Providing 15mm thick cement plaster ( Mala
Trowel finish) in single coat on brick/concrete
walls for interior plastering upto floor two level
25 and finished even and smooth in (i) Cement 240.00 Sqm 228.77
mortar 1:4 (1-cement:4-sand) including
finishing coat of neat cement slurry for First
Providing 10mm thick cement plaster in single
coat on brick/concrete walls for interior
plastering upto floor two level and finished
26 even and smooth in (i) Cement mortar 1:3 (1- 128.00 Sqm 201.88
cement:3-sand) including finishing with a
flating coat of neat cement slurry etc.
complete. for Ground Floor
Providing 10mm thick cement plaster in single
coat on brick/concrete walls for interior
plastering upto floor two level and finished
27 even and smooth in (i) Cement mortar 1:3 (1- 26.00 Sqm 223.20
cement:3-sand) including finishing with a
flating coat of neat cement slurry etc.
complete. for First Floor
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Wall painting (three coats) with plastic
emulsion paint of approved brand and
manufacture on undecorated wall surface to
28 give an even shade including throughly 992.00 Sqm 113.96
brushing the surface free from mortar
droppings and other foreign matter and sand
papered smooth.
Wall painting (three coats) with plastic
emulsion paint of approved brand and
manufacture on undecorated Ceiling surface
29 to give an even shade including throughly 128.00 Sqm 118.36
brushing the surface free from mortar
droppings and other foreign matter and sand
papered smooth.
20mm thick sand faced cement plaster on
walls upto height 10 metres above ground
level consisting of 12mm thick backing coat of
C.M. 1:3 (1-cement : 3-sand) and 8mm thick
finishing coat of C.M. 1:1 (1-cement : 1-sand)
etc. complete.
Providing and laying Mirror polished Machine
polished Telephone Black Madras Granite
stone slab 18 mm (Average) thick for For
Doors / WIndows cill & Jams Clading as per
design incl. full moulded round front edge in
31 trade of steps laid on 20 mm thick cement 14.40 Sqm. 3550.15
mortar 1:6 (1 -cement : 6 coarse sand )
jointed with grey cement slurry including
rubbing and polishing etc. complete For
Doors / WIndows cill & Jams Clading
Finishing wall with weather proof exterior
emulsion paint on wall surface (two coats) to
give an required shape even shade after
thoroughly brushing the surface to remove all
dirt, and remains of loose powdered
materials.etc complete
Providing laying and joining in true line and
level U.P.V.C. Pipe (SCH-40) including fittings
of Prince / Supreme / Astral / Finolex or
equivelant make or as approved by Engineer
in Charge . Pipe shall be fixed on the wall with
33 the help of clamp at every two meter C/C or 120.00 Rmt. 91.84
shall be concelled as directed including
necessary fittings etc. including testing of pipe
and joints and fixing the same with adhesive
solvent including cost of all materials (i)
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Providing laying and joining in true line and
level U.P.V.C. Pipe (SCH-40) including fittings
of Prince / Supreme / Astral / Finolex or
equivelant make or as approved by Engineer
in Charge . Pipe shall be fixed on the wall with
34 the help of clamp at every two meter C/C or 60.00 Rmt. 72.65
shall be concelled as directed including
necessary fittings etc. including testing of pipe
and joints and fixing the same with adhesive
solvent including cost of all materials (ii)
Providing and fixing C.P. Bib Cock 15mm dia.
35 Heavy Duty with cap ( Plumber, Mark, Escco 2.00 No. 447.04
or equivelent brand )
Providing and fixing C.P. Bib Cock 15mm dia.
36 Heavy Duty with cap ( Plumber, Mark, Escco 5.00 No. 436.93
or equivelent brand )
Providing and fixing Divertor of following size
(A) Brass chromium plated with top body
fitted after tiling (i) 25mm dia. ( Plumber, Mark,
Escco or equivalent brand )
Providing and fixing Heavy duty Spout of
following size (A) Brass chromium plated with
38 top body fitted after tiling (i) 15mm dia. ( 2.00 Nos. 1654.38
Plumber, Mark, Escco or equivalent brand )
Providing and fixing Heavy duty Shower of
following size (A) Brass chromium plated with
39 top body fitted after tiling (i) 15mm dia. ( 2.00 Nos. 1556.64
Plumber, Mark, Escco or equivalent brand )
Providing and fixing CP brass Pillar tap swan
neck ( Heavy duty), (A) 15 mm dia {Jaquar,
Plumber, Mark Long pipe or equivalent brand}
Pro. & Fix. wash down water closet
(European W.C pan of Vitreous china Patern.)
with integral" p " or " s " trap and PVC
flushing cistern with a pair of C.L.I. Or Mild
steel Brackets, complete with fittings such as
lead value siphon, 15 mm. Nominal size brass
ball valve with polythene float, C.P. Brass
41 handle unions and couplings for connections 2.00 No. 2280.58
with inlet, outlet and over flow pipes, 40 mm.
dia. flush bend including cutting holes in walls
and making good the same connecting the
flush bend with cistern and closet etc comp
incl plastic sheet cover including jointing trap
with pipe in cm 1:1 (a ) Vitreous china in
white or color
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Provision and fixing water closet squatting
orissa type W.C. pan size 580mm integral
footrest and 100 mm P or S trap and in
42 cluding 25 mm dia CP brass flush valve and 2.00 No. 1289.77
GI inlet connection etc. comp. (A) Vitreous
china long pattern white or color {Hindustan,
Cera, Parryware or equivalent }
Providing and fixing wash basin with pedestal
of std. Height with single hole for pillar tap with
C.I or M.S brackets painted white including
cutting cutting holes and making good the
same including C.P. brass waste and waste
pipes and bottal trap (A) Vitreous China: (ii)
Flat Back washbasin 550 mm x 400mm
size.In colour.
Providing erecting and fixing double coated
Syntex PVC. (ISI) water tank of required
44 1000.00 Litre 3.95
capacity each with all necessary fittings and
connection etc. complete on terrace.
Providing and fixing Handle valve of approved
brand (B) 25mm dia.,
Providing and fixing C.P. brass towel rail
comlete with C.P. brass brackets fixed to
wooden plugs with C.P. brass scews.(B)
600mm x 20mm size.
Providing & Fixing PVC SWR Nanhi trap IS:
14735 for drain with jali of the following
nominal diameter of self cleaning design with
47 C.I. screwed down or hinged grating including 4.00 No. 558.36
the cost of cutting and making good the walls
and floors 100mm inlet and 50mm outlet. size
P of R type
Providing and fixing S.W. gully trap with C.I.
grating brick masonry chamber and water tight
C.I. cover with frame of 300mm x 300mm size
(inside) with standard weight. (i) Square
mouth traps.(B) 150mm x 100mm size P of R
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Providing, laying and jointing in true line and
level 110 diametre U.P.V.C (Type B)
conforming to IS 13592-1992 with one end
plain and other end socketed with rubber ring,
& fittings conforming to ISI 14735-1999 of
approved make for drainage system pipe line,
pipe shall be jointed with each other with
rubber lubricant, pipe shall be fixed on wall
49 using of PVC clamp of the size 110 mm 13.00 Rmt. 835.15
diametre x 149 mm length x 145 mm heigh at
every 2000 mm center to center or shall be
concealed in walls as directed including
necessary fittings such as bends, shoes etc.
including testing of pipes and joints and
jointed with adhesive solvent cement including
cost of all materials.
Constructing brick masonary chamber for
under ground C.I. Inspection chamber and
bends with bricks having crushing strength not
less than 35kg/ cm2 in C.M. 1:5 C.I. Cover
with frame ( light duty) 450mm x 610mm x
450mminternal dimension total weight of
cover with frame to be not less than 38Kgs
(weight of cover 23kg and weight of frame
50 15Kg). R.C.C. top slab with 1:2:4 (1 cement : 2.00 No. 2932.93
2 coarse sand : 4 graded stone aggregate
10mm nominal size) foundation concrete
1:5:10 inside plaster 1:3 finished smooth with
a floating cost of neat cement on walls and
bed concrete etc. comp. with one or two
inlets..(i) Inside dimensions 455mmx 610mm
and 450mm deep for single pipe line.
Providing sock pit of 5.00 Cu.M. Volume
including excavating and filling brickbats with
dry masonry work at top for 45cm. height
including covering the top with stone including
providing vatas in C.M. 1:3 with finishing
curing etc. complete as directed
Providing and fixing pre-cast Rubber Dye inter
locking concrete block 60mm thick with grade
of concrete M250 pnumatic compressed by
mechanically pressed and as per approved
design including 75mm Sand layer for
levelling and filling the joint with sand in
proper line and level etc complete.
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Constructing Sandwitch Platform of 18 mm
thick Polished Black Granite at top and 25 mm
thick Kota stone slab using cement mortar 1:3
for sandwich and fitting at bottom & edges
with waterproof rigid adhesives including
macking necessary grooves in walls with
Vertical Kotastone 30 mm x 2 No sandwitch
53 thick every 60 cm centre to cenre including all 4.50 Sqm. 2838.10
labour material of approved quality incl. full
moulded round front edge fixed in wall for
partition and jointed with grey cement slurry
including rubbing and polishing etc. complete
(R .A . attached )
Providing and fixing sheet glass, decorative
quality ( Colour Desing ) (Type-C) bedded in
putty and fixed with wooden beading including
the cost of wooden beadings of first class
teakwood and necessary cutting of glass. (1)
5 mm thick.
Providing and fixing kitchen sink with S.S.
Sink Glosy ASIS 304 Grade x 1mm thick with
over all size 610 x 460 mm & bowl size 560 x
55 410 x 200 including cutting holes in walls and 1.00 No. 1700.84
making good the same with including all
fittings ( Nirali Brand or equivalent)
Plantation of trees in soil including digging
x 45 x 45cm size pits, preparing soil providing
56 and mixing fertilizer, watering, planting and 20.00 No. 40.40
filling the pits as per direction including etc.
Providing Tree Plants having minimum
1.00mt. Height and healthy grouwth of various
kinds as like Peltoform, Palm,Gulmahore,
Karanj, Amla, Rain tree, Saptparni, Cherry,
Cryjeliya, Spethodiya, Paras Pipala, Garmalo,
Neem, Borsalli, Kadam, Buch, Chanpo,
Asopalav etc. as per instruction by engineer in
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Providing and fixing of Ridge flashing for roof
panel shall be made out of 0.5 mm thick pre
coated GI sheet . The Precoated sheet shall
be of minimum 240 mpa steel grade
confirming to IS 14246:1995 and shall have
zinc coating of minimum 120 gsm as per
IS:277:1992 , 5-7 microns epoxy primer on
both side of the sheet and polyester top coat
58 15-18 micron. The PPGI Sheet shall have 21.00 Sqm. 858.67
plastic protective guard film of minimum
microns to avoid scratches during
transportation. The ridge shall be fixed to the
steel members by pop rivet or self drilling/self
stitching fastners @ maximum 450 mm c/c
along length of capping/flashing etc complete .
Providing and fixing Y type 1.00m high fencing
with 1.20mt long M.S. angle posts 40mm x
40mm x 6mm and oil painting 3 coats fixed at
2.50m c/c with five horizontal lines and two
59 diagonals of galvenised steel barbed wire 120.00 Rmt. 312.49
weighting 9.38kg. Per 100m. Strained and
fixed to posts with G.I. staples including fixing
posts in brick columns with C.C. 1:2:4 of size
Steel work, riveted in built up sections framed
work including cutting, hoisting, fixing in
position and applying a priming coat of read
lead paint. (D) In trussses and trussed purlins,
upto 25 M. span and 15 M ovarall height.
Painting Two coats (excluding priming coat)
on previously printed steel and other metal
surface with synthetic enamel paint, brushing
to give an even shade including cleaning the
surface of all dirt, dust and other foreign
Polishing with french polish on previously
polished wood and wood based surface to
give an even surface including cleaning, the
surface of all dirt, dust and sand papered
smooth and including a coat of wood filler.
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Providing and Alluminium Composite panel of
ALSTRONG or equivalent brand with
approved shade of 4 mm thick ( 0.5 +3+0.5 )
.The Composite panel should be made of
3mm thick 100 % virgin poly thene core of
LPDE sandwitched between 100 % virgin poly
thene core of LPDE sandwitched between is
having tthree layers of PVDF coating with
63 Kyanar 500 paint to ensure the superior 14.00 Sqm. 2605.80
corrosion resistance and weatherability and
the other side is service coated with Epoxy
paint ( Grey ) .The ashesive used DUBOND
for bonding the two skins which can take 8 to
9 Kg. of weight to seperate . This includings
structural frames for fixing and finishing etc.
Providing & Supplying Wooden Chairs having
size of 470 (W) X 500 (D) X 900 (H) mm,
made out of Special Indian teakwood in
framing, seat and back rest with smooth &
curved edges in arm rest, seat/back,
64 Cushioning of PU foam 40 Density in Seat & 3.00 Nos. 3030.00
with requisite no. of coats of melamine
polishing, plastic buffers, etc. complete as per
drawings and designs supplied by the
Architect and instructions by Engineer in
Providing & Supplying Wooden Bed having
size of 1500 (W) X 1500 (D) X 450 (H) mm,
made out of Special Indian teakwood in
framing, seat and back rest with smooth &
curved edges with requisite no. of coats of
65 melamine polishing, plastic buffers, etc. 2.00 No. 14645.00
complete as per drawings and designs
including the bed curlon cushion with two
piloow with bedsheet & Pillow cover supplied
by the Architect and instructions by Engineer
in Charge.
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Point wiring for Light / Bell with 2-1.5 sq.mm &
earthwire of 1.5 sq.mm (Green) both are of ISI
marked 1.1 KV grade FRLS PVC insulated
multistrand copper wires, in following type of
pipe to be erected concealed in/ on surface on
wall/ceiling complete with 6A Modular type
switch / bell push & accessories and earth
continuity of following type, erected on PVC /
66 Metallic box, single mounting base frame 10.00 Pt. 419.15
covered with textured/metallic front plate
modules erected on / in wall / ceiling as per
pipe erected with necessary Lamp holder /
ceiling rose / H.D. Connector as directed. (a)
with medium class Rigid PVC pipe and
accessories. Cat-III.
Point wiring for FAN with 2-1.5 sq.mm &
earthwire of 1.5 sq.mm (Green) both are of ISI
marked 1.1 KV Grade FRLS PVC insulated
multistrand copper wires, in following type of
pipe to be erected concealed in / flushed on
wall/ceiling complete with 6A Modular type
switch and hum free EME four or more step
type electronic fan regulator with separately
mounted and accessories with earth continuity
67 of following type erected on PVC / Metallic 10.00 Pt. 598.93
box, single mounting base frame covered with
textured / metallic front plate modules erected
on / in wall / ceiling as per pipe erected. with
necessary ceiling rose / H.D. Connector as
directed. (a) with medium class Rigid PVC
pipe and accessories. Cat-III
Point wiring for on board Looped Plug with 6A
Modular type switch & 5 pin socket erected on
PVC / Metallic box, single mounting base
68 frame covered with textured / metallic front 5.00 Pt. 241.39
plate modules erected on / in wall / ceiling with
following type accessories Cat-III.
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Mains with 1.1 KV grade FRLS PVC insulated
ISI marked stranded Copper conductor wire in
following type of pipe to be erected concealed
in /flushed on wall/ceiling, with 1.5 sq. mm
copper conductor FRLS PVC insulated
stranded wire of green colour for earth
continuity of following size (a) with medium
class Rigid PVC pipe and accessories (b)
wire 2.5 sq. mm
Providing & erecting Switch board for
Computer or electric apparatus consisting of
following items in single board erected on
PVC / Metal board with 3 mm thick PC
70 (Polycarbonate) / Acrylic sheet erected as 3.00 Nos. 1081.71
directed 1 no. 6A/16A universal plug-switch
3 nos. 6A Switch 3 nos. 6A 5 pin Plug [B] For
Modular Type Accessories Cat-III
Supplying and erecting LED indoor fittings
with LEDs of watt age 0.2Watt to 0.5Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS:513/CRCA/
aluminium die cast powder coated and high
U.V.& corrosion resistance with diffuser with
company mark / name 120 to 300V ,Power
Factor more than 0.9,THD<10 %,CCT 3000 K
to 6500K, Luminair eefficacy >85lumens/ watt,
LED efficiency -110 lumens / watt LED driver
71 efficiency > 85 % CREE / OSRAM / PHILIPS 5.00 Nos. 589.84
Lumileds /NICHIA/SEOUL/ Bridge lux make
LED used for luminaire. (fitting required LM-79
& LM-80 Certificates) (NOTE: Below
description have shown ranges of Watt age
capacity of LED fittings. The Engineer
between the ranges shown.)(A) Tube Light
with integral driver(c) 20 Watts, Surge -
2KV,IP-20, 4 feet Cat-III
Supplying and erecting led lamps with
following wattage capacity of 220 to
voltage, minimum 15000 burning hours life,
500 V in built-surge protection, Polycarbonate
72 diffuser, mounting suitable for E14 / E27 / B22 4.00 Nos. 112.11
lamp holders, pf >= 0.5 (B) LED Lamps
integral type, with PC diffuser suitable LAMP
holder (b) 5 to 8 watts Cat-III
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Supplying and erecting LED street light / Flood
light fittings with High power White LED
wattage of 1Watt and above assembled on
single MCPCB, efficiency more than 130lm / w
and corrosion free High pressure die cast
aluminum housing with smooth finish powder
coated and heats inkextruded aluminium with
diffuser and Polycrbonate optics /l enses with
company mark / name engraved orembossed
120 to 300V, Power Fact ormore than 0.95,
THD<10%,CCT3000 K to 5700K ,Uniformity
73 ratio>0.45, Luminaire efficacy>100 lumens 3.00 Nos. 5976.17
/watt. LED driver efficiency >85%. CREE /
OSRAM / PHILIPS Lumileds / NICHIA /
SEOUL / Bridge Lux (U.S.A.) make LED used
for luminaire. (fittingsrequiredLM-79&LM-80
certificates) (NOTE: Below description have
shown ranges of Wattage capacity of LED
any wattage capacity between the ranges
Providing and erecting Miniature circuit
breaker single pole 6A to 25A suitable to
operateon 240VA.C. system and having
breaking capacity 10KA to be erected in
existing box. Confirming to IS 8828/1996 with
ISI Mark Cat-III
Approved make ELCBs / RCCBs conforming
to IS: 12640 and having sensitivity of 30 mA
and Short Circuit withstand capacity of 6 KA
and suitable for operation on 3 phase and
neutral 415V. having characteristic of quick
action & tripping with all advance feature & do
not incorporate any electronic component for
following Max. rating erected as directed. (ii)
40 Amps. DP Cat-III
Providing and erecting XLPE(IS:7098)(I)-88ISI
armoured cable Aluminium conductor for
1.1KV. To be laid on wall with necessary
clamps or inexisting trench / pipe of following
size of cables. (B) 2 core 6 Sq. mm
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Providing and erecting Approved make
Ceiling fan with double ball bearing ISI mark
with condenser A.C. 23O V.50 c/s.1200 mm.
sweep complete, canopy and 30 cms. down
rod erected on existing hook or clamp with
24/0.2, 3 core flexible wire with earthing.
[Make shall be approved by Engineer in
Supplying and erecting approved make
Octagonal pole made from HR sheet steel.
The pole should be made as per IS. and shall
be coated with hot dip galvanizing as per
IS2629/2633/4759, suitable suspend local
wind speed with integral Junction box consist
of terminal plate of min 6mm Hylamsheet,
standard profile 35mmX7.5mmDin-Rail for
78 MCB Mounting, studty peterminal and 3.00 No. 6874.06
arrangement for cable termination to be
erectedon suitable foundation (icluded).
(C)5Mtr.Long 70mmTop X130mm bottomdia,
3mmthickness with 200mmX200mmX12mm
base plate, 4-M16 Bolts and 600mm long J-
Supplying and erecting Street light pole
bracket comprising main BClass MS pipe of
4.2cm/ require outside dia. complete with
suitable BClass M.S.sleeve tubing of approx.
45cms. length and suitable for
76.5mm/80mm/ require size of pole top
having nuts and bolts for fixing the brackets
79 and having spread of 0.5mtr. Length with 3.00 No. 450.46
110deg. with vertical plane and suitable
welded stiffener reducer and nipple with check
nut complete painted with one coat. of
Redoxide /PU base primer and two coats of
Aluminium/ PUpaint. paint with following nos
of arms. A] Single Arm bracket 0.5 / 0.75 Mtr
Description of Item
Item Rate In
(with brief specification and reference to Quantity Unit Amount
No. figures
book of specifications)
Supplying and erecting Fully Automatic hydro
pneumatic booster system with cast iron
housing Enclosure class IP44 minimum , with
built in PTO motor protection and stainless
steel impeller pump, pump model
GRUNDFOS CMB 5-46 series or equivalent
with 24 Liter hydro pneumatic pressurized
tank capacity : 5 m3/hr,Rated head :30 mtr,
motor rating : 1.2 H.P. includes pressure
switches, Non Return Valve, Pressure Gauge,
5 way Brass connector, with necessary
Plumbing work which includes all required
size of pipes, Joints valves, Bypass valve,
labor all accessories required for installation of
pressure pump ( Foundation work and base
stand cost included)
Total Rs.
Rupees Sixteen Lakh SeventySeven Thousand Five Hundred Five and Paisa EightyTwo Only
I / We / am/are willing to carry out the work at ________________________________% above / below
percent (should be written in figure and words) of the estimated rates mentioned above. Amount of
my/our tender Works out as under.
Estimated Amount Estimated Amount
put to tender Rs. _________ put to tender Rs. _________
Deduct_______% below Add_______% above
Net Rs._________ Net Rs._________
in words ___________ in words ___________
The Contractor shall exhibit a board with detailed specification and details of work as directed by
the Engineer-In-Charge for which no extra payment shall be made.
2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.
3 GST and Income tax TDS will be deducted at a source while making payments of bills.
In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt.
G.R.: PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in
4 R.C.C. items where there is a change as per actual mix design the cost of difference of cement
consumption have been deducted from the rate of original item at the rate of input rate mentioned
in all the tender.
Dismentalling of Credit materials amounting of Rs. 0.00 must be recovered from Contractor's
respective R.A. Bill.
Signature of Contractor
Dy. Executive Engineer Executive Engineer
Panchayat R.&B Sub Division Panchayat R.&B.Division
Gandhinagar Gandhinagar
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
BOQ Reparing Rest House At Sadara.pdf
BUILDING WORK BOOKLET.pdf
General Specification - Building.pdf
GR - 1.pdf
GR - 2.pdf
SBD Book_ Reparing Rest House At Sadara.pdf
Specification Index - Reparing Rest House At Sadara.pdf
Download all tender documents and submit your bid