ADDN/ALTN TO BLDG NO P-197 FOR WOMEN AGNIVEER AT INS GARUDA, SPECIAL REPAIR TO P-83 BUILDING AT INS GARUDA, PROVISION OF DEFICIENT TWO WHEELER PARKING SHED NEAR P-133 BLDG BV YARD, PROVISION OF SPARK PROOF ARRANGEMENT IN BATTERY ROOM (BLDG NO P-45) A

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding, (but not backing) removing serviceable tiles to store and rubbish of premises complete all as specifeid and directed.

M&L Non - Skid coloured Ceramic tiles 7 to 8 mm thick (Square/ Rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screed in Cement Mortar 1:4, complete all as specified.

M&L for Glazed ceramic tiles coloured , as in vertical surfaces, size 350x 250x 7 mm/450 x 350 x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles including 10 mm thick backing coat in Cement Mortar 1:4, complete all as specified and directed.

M&L for Vitrified ceramic tiles, light shade, 10 mm thick (Square / Rectangular), polished, area of each tile not exceeding 0.36 Sqm, laid in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match, including 10 mm thick Screed bed or bedding layer in Cement Mortar 1: 4, complete all as specified and as directed by Engineer in Charge.

M&L for Vitrified ceramic tiles, light shade, in skirting 10 mm thick (Square / Rectangular), polished, area of each tile not exceeding 0.36 Sqm, laid in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match, including 10 mm thick back coat in Cement Mortar 1: 4, complete all as specified and as directed by Engineer in Charge.

Demolition of Plain Cement Concrete in ground floors and pavings not exceeding 15 Cm thickness (below or above gound level) complete all as specified and as directed.

Demolition of brick work or stone, boulder, precast PCC block masonry including all quoins, arches, pillar etc. built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for Precast cement concrete block masonry with solid blocks, Type C-1, 1:3:6 (using 20mm graded stone aggregate) exceeding 10 cm in width and setting in Cement Mortar 1:6, complete all as specified and as directed.

M& L for 10mmm thick cement plaster in CM 1:6 on fair surfaces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement all as specified and directed by Enrgineer in Charge.

Taking down cement plaster on Brick/ Concrete wall and ceilings, including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed by Engineer in Charge.

M&L for cement plaster in two coats, 8 mm thick in cement mortar 1:4 using WPC over 12mm thick in cement mortar 1:6 on external surfaces, finished even & smooth without using extra cement all as specified and directed. Note : WPC shall be measured and paid seperately.

Supply only Integral waterproofing compound complete all as specifeid and directed.

M&L for preparation of new decorated surface of walls including cornices (Plastered or unplastered) and applying two coats of antifungal paint over a coat of primer, complete all as specified and as directed.

M&L for complete removal of exisiting treatment from wall and applying two coats of antifungal paint over a coat of primer, complete all as specified and as directed.

M&L for preparation ofold decorated surfaces of ceiling and applying three coat of white wash complete all as specified and as directed by Engr-in-Charge.

M&L for complete removal of existing finishes from the old plastered surfaces of wall (plastered or unplastered) including cornices and applying two coats of distember oil emulsion over a coat of alkali resistent primer, over 1mm thick wallcare putty complete all as specified and as directed by Engineer in Charge.

M&L for preparation of newly plastered surfaces of wall (plastered or unplastered) including cornices and applying two coats of distember oil emulsion over a coat of alkali resistent primer, over 1mm thick wallcare putty complete all as specified and as directed by Engineer in Charge.

Taking down chowkats with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm, complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm, but not exceeding 4 Sqm, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory made Solid Panel PVC door shutters, both sides using Prelam PVC sheet, 30 mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side Prelam colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply and fixing 200 mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing 150 mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

Supply and fixing 250mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

Supply and fixing 100mm size Stainless Steel butt hinges, medium weight, complete all as specified and directed.

Supply and fixing 150 mm size extruded, anodised aluminium alloy handles, fabricated type, complete all as specified and directed.

Supply and fixed in repair Tubular towel rail brass chromium plated , 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

Supply and fixed in repair stainless steel curtain rail bright finished, 25 mm dia. decorative type, complete all as specified and as directed by Engineer in Charge.

Supply and fixed in repairs, stainless steel bright finished decorative brackets/ finials for curtain rail 25mm dia., complete all as specified and directed.

Supply and fixed aluminium alloy body door stopper and tongue anodised with hard drawn steel spring in floor, 140mm over length of cover plates, complete all as specified and directed.

Supply and fixing aluminium alloy wire cloth, 0.45 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples, complete all as specified and directed.

Supply and fixing 4.00mm thick frosted glass, pin head type and glazing with oil putty/ beads in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F second classhard woood plain solid,straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put togethr with glue pinned at joints complete all as specifeid and directed.

M&L for M.S Hold fasts of FI 25 x 3 mm complete all as specifeid and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in hold fast blocks complete all as specifeid and directed.

S&F 35 mm thick IInd class hard wood factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with out mitred beads for securing glass etc. complete all as specifeid and directed.

S&F 35 mm thick Plain, framed, panelled shutters (any number of panels), IInd class hard wood with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats etc. complete all as specifeid and directed.

M&L for painting to new wooden surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specifeid and directed.

S&F Door closer hydraulically regulated, designation No. 3, universal type, Aluminium (Extruded Section body) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed all as specified & directed.

S&F Aluminium powder coated sliding type window with 4mm thick plain sheet glass, Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm, including provision of airtight heading and handling arrangements complete with using following Hindalco sections: (i) 4097, 3 track bottom (ii) 4098, 3 track side and top (iii) 9777, Shutter vertical (iv) 9778, Shutter Interlock (v) 3994, Shutter top and bottom Note : Two sliding shutter shall be with 4mm sheet glass and one sliding shutter shall be with wire mesh. Maximum width of one sliding window does not exceed 1.50m.

S&F Anodised aluminium powder coated window and ventilator shutters, (minimum thickness of powder coating 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F for Powder coated anodised aluminium frame for doors, windows, ventilators (minimum thickness of powder coating 50 micron), with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge.

Supply and fixing 4.00mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by the Engr -in-Charge

Supply and fixed in repairs, vitreous China wash down water closet single piece (pedestal pattern) white, (including fixing bolts) including removing old one and connection to drain and flush pipe, complete all as specified and directed. Make: Parryware single piece suite Apollo C8939 (S-220) (690 x 375 x 730mm) or Eqivalent make of Hindware/ Cera

Supply and fixed in repairs, plastic water closet seat for single piece closet, white, closed pattern with flat bottom and cover and mild steel chromium plated or alumininsed hinging device, complete all as specified and directed. Make : Parryware EWC Seat cover E 8305 Ultra Solid white or Equivalent make of Cera/Hindware

Supply and fixed in repairs, PVC valveless syphonic action type, 10 Litres Capacity Flushing Cistern, low level, white, with inlet, ball valve, float and handle including MS brackets including flush pipe PVC connections etc. complete all as specified and directed.

Supply and fixed in repairs, Vitreous China Wash Hand Basin of size 580mm x 450mm, White, flat back and including waste fittings, brass chromium plated 32 mm with long and fly nut screwed shank, excluding taps, waste chain and plug and porcelain stopper but including cast iron brackets, complete all as specified and directed.

S&F in repairs, 15mm bore Fancy type brass chromium plated Pillar taps, with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Pillar Tap with aerator Parryware Cart Part No.Crust T3102A1 or Equivalent make of Hindware/ Cera

S&F in repairs SS Soap dish, complete all as specified and directed. Make : Parryware Cart part No.T6902A1 or Equivalent make of Cera/ Hindwar.

S&F in repairs, PVC Bathroom Cabinet (White) of size 420mm x 300mm x 100mm (Approx.), with single shutter and built in mirror in front of shutter, complete all as specified and as directed by Engineer in Charge.

S&F in repairs, corner glass shelf of 5mm thick, plain sheet glass and with brass, chromium plated bracket complete all as specified and as directed by Engineer in Charge

S&F in repairs, PVC backing looking mirror of size 45cm x 60cm fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed by Engr-in-Charge.

Supply and fixed in repairs, 100 mm dia. PTMT gratings with provision to receive the waste water pipe and fixed with white cement alround, with minimum weight 25 gms., complete all as specified and directed.

Takin down Wall panelling and similar work complete all as specifeid and directed.

S&F for Solid PVC Wall Lining consisting of 5mm thick Plain wood grain printed colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame/aluminium frame as per specifications and drawing complete all as specified and directed by Engr-in-charge Note : PVC / Aluminium frame shall be measured seperately.

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. etc complete all as specified and directed by Engr-in -charge

Taking out existing roof treatment alongwith screed, tarfelts,tiles etc, and removal of dismantled materials complete all as directed and as specified

M&L for 10 mm thick rendering in cement mortar 1:3 with water proofing compound for roof treatment complete all as specified. Note : WPC shall be measured seperately.

M&L for water proofing treatment over RCC slab (i) Apply a coat of oil based bituminous primer @ 0.25 Kg / square metre on the prepared surface. (ii) Apply a coat of blown type bitumen grade 85/25 conforming to IS: 702 heated to a working temperature of 180 degree centigrade and applied @ 1.20 Kg /Sqm of the surface area. (iii)Provide and lay 4 mm thick APP modified torch applied water proofing membrane weighing not less than 4.0 Kg / Sqm reinforced with non-woven polyester matt weighing not less than 160 gm / Sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 650 N/5 cm, tear strength of 180 N (min), a static puncture resistance of 180, keeping a minimum of 10 cm side over laps and 15 cm end lap. (iv)Apply a coat of blown type bitumen grade 85/25 conforming to IS: 702 heated to a working temperature of 180 degree centigrade and applied @ 1.20 Kg /Sqm of the surface area. (vii)Finishing surface with solar reflective bituminous aluminium paint @ 0.10 Kg / Sqm.

Supply of Liquid water proofing compound complete all as specifeid and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and as directed by engineer in charge

M&L for Hard core of Gauge exc. 63mm but n. exc 150mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rolled / rammed to a true surface complete all as specified and as directed by Engineer - in- Charge.

M&L for 100mm thick cement concrete type D2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified and as directed by Engineer - in -Charge.

M&L Coarse aggregate of grade from 4.75mm to 12.5mm for cushioning under paver block Spreading and levelling and ramming as specified complete all as specified and as directed by Engr-in-Charge.

M/L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, with grey cement and pigment complete all as specified and as directed by Engr-in-Charge.

M&L for PCC type B-0, 1:2:4 (12.50mm graded aggregate) as in mass concrete around the machine pressed pre cast concrete paver block or chamfered on edges all as specified and as directed by Engineer - in - Charge.

S&F for Powder coated Anodised aluminium (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F for 12mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work/Aluminium frame work complete all as specified and as directed.

S&F Aluminium Mortice lock, vertical type, size 100 mm, 4 lever complete all as specified and as directed.

S&F for 5.50mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specifeid and directed.

S&F for Solar control film 50 micron reflective type (gareware sun control or equivalent) complete all as specified

Dismantling SS railing work of any description complete all as specifeid and directed.

S&F for Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specifeid and directed.

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for preparing new steel and iron surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint, over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F for PVC backing looking mirror of size 45cm x 120cm fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed by Engr-in-Charge.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Surface excavation in soft and lose soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified

Removal of excavated material (Soil) n. exc. 50 mtr and deposting where directed at level n.exc. 1.50 mtr above starting point complete all as specifeid and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep and getting out in loose/soft soil complete all as specifeid and directed.

M&L for PCC 1:2:4 type B 1 as in foundation, filling & mass concrete complete all as specifeid and directed.

S&F mild steel work in framing, purlin using section such as angle, hollow pipes , flats etc using Fe-290 Grade E-165 complete all as specifeid and directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge , Gutter, Gable flashing, corner flashing etc, fixed with self tapping screws as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of anti corrosive Epoxy paint over a coat of Epoxy primer complete.

S & F 200 mm dia of half round or 220 mm width rectangular UPVC SWR ready made eaves gutter of pressure rating 6 Kg/cm2 of approved make including necessary fitting like bend WC/MS Clips etc complete all as specified.

S & F 150MM dia of PVC (SWR) pipe single socketed in any length with rubber joints including necessary fitting like bend WC/MS clips etc fixed on walls complete all as specified

M&L for PCC 1:4:8 Type D2( 40mm graded aggregate) in foundations, filling and mass concrete complete all as specifeid and directed.

M&L for 40 mm thick plain cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in hard standing, laid in alternate bays including necessary form work and finishing the surface of concrete fair and even without using extra cement complete all as specified and directed by Engineer-in-Charge.

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A" complete all as specifeid and directed.

M&L for cement plaster 15 mm thick in cement mortar 1:4 in two coats (10mm + 5mm) using WPC finished even and smooth without using extra cement for external faces of walls complete all as specified and as directed.

Taking down aluminium/copper point wiring (light,fan,socket or power) complete,including fixture and fittings such as switches,ceiling roses,pendants,regulators,sockets,light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls,floors,etc. complete all as specifeid and directed.

M&L , point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits) with 1.5 sqmm nominal cross sectional area, copper conductor unsheathed FRLS cable 1100 Volts grade ISI-694 marked with valid CML No. single core multistranded cable in and including medium grade surface PVC conduit not less than 20mm dia and accessories ISI marked with valid CML No (IS-9573-1983 for conduits and IS: 3419: 1976 for conduit accessories) and with modular switch boxes and PVC modular cover plate of suitable size for fixing of switches sockets and fan regulators etc. including 1.5 Sqmm nominal cross sectional area PVC insulated copper conductor unsheathed FRLS cable single core multistranded cable as earth continuity wire all as specified and as directed for One light point controlled by one switch complete all as specified and as directed by Engineer-in-Charge.

Same as per item No. 99 but One fan point / exhaust fan point controlled by one switch & regulator complete all as specified and as directed by Engineer-in-Charge.

Same as per item No. 99 but One 5 pin 5 Amps Socket point controlled by one switch on same board complete all as specified and as directed by Engineer-in-Charge.

Same as per Item No. 99 but One 5 pin 5 Amps socket point controlled by one switch on independent board complete all as specified and as directed by Engineer-in-Charge.

All as per item No 99 above but with 2.5 Sqmm copper conductor including 2.5 Sqmm copper cable as earth wire for one 6 Pin 16 Amps Socket outlet on independent board complete all as specified and as directed by Engineer-in-Charge.

S&F modular switch 1 way 6 Amps,1 module complete all as specified and as directed by Engineer-in-Charge.

S & F socket modular 6 Amps and 2/3 pin combined 2 module complete all as specified and as directed by Engineer-in-Charge.

S & F Modular socket 6 A/16 A - 2/3 pin combined 2 module complete all as specified and as directed by Engineer-in-Charge.

S&F switch 15 A One way SP modualr type complete all as specified and as directed by Engineer-in-Charge.

S & F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specified and as directed by Engineer-in-Charge.

S&F fan regulator electronic step type, modular type, 120 W, 2 module, 5 steps complete all as specified and as directed by Engineer-in-Charge.

Supply & fix Regal Batten for LED tube lights, both side connection type and with ISI marked, medium grade LED tube rod 1 x 20 Watt, 120 Lumen/Watt both side connection complete all as specified and as directed by Engineer-in-Charge. Make of batten : Havells Cat Part No. Regal batten 8UPT001X22WSSBSWH. Make of tube rod : Havells Cat Part No. Crystal 1213T8DSTL20W LED 865 GLASS or equivalent any other make in the approved manufacturers list.

Supply and fix 12w LED Bulb with B22 base, clear acrylic diffuser, Self declaring R No, power factor .90, 120 lumens light output complete all as specified and as directed by Engineer-in-Charge. Make :- Luker Cat Part No. LBPC12CL or any other make of the approved manufactures list.

M&L in repair, lamp holder ,PVC /poly carbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-Charge.

S&F energy efficient ceiling fan of 1200mm sweep 230 Volt 50 Hz including all electrical connection complete all as specified and as directed by Engineer-in-Charge. make :- Havells Cat Part No. ES-40 or equivalent any other make in the approved manufacturers list.

Supply and fix PVC body exhaust fan 230/ 240 V of size 250 mm sweep with louver complete all as specified by Engr-in-Charge. Make : Havells Cat Part No. Ventil Air DX White or equivalent any other make in the approved manufacturers list.

Supply and fixing including all fixing arrangements on walls/ steel surfaces Wall Mounting Fan (Air Circulator), Metallic body, Heavy duty 300 mm sweep complete all as specified and as directed by Engineer-in-Charge. Make Havells Model No. D'zire HS or equivalent any other make in the approved manufacturers list.

Supply and fixing amp rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) 40 to 63 amps of two poles anc current carrying capacity in the DB Complete with connection testing and commissioning complete all as specified

Supply and fixing in repair 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 5 Amp to 32 Amps in the MCB DB Complete with connection testing and commissioning complete all as specified

S&F SPN sheet metal enclosure for DB 12 ways Double doorcomplete all as specified and as directed by Engineer-in-Charge.

Taking down old sub main wiring of any size complete all as specifeid and directed.

M/L submain wiring with 2 single core 4 Sqmm PVC insulated unsheathed multistranded copper conductor cable 1100 volt grade drawn throgh and including PVC rigid conduit concealed wiring inculding necessary PVC conduit specials including chases cutting complete exceapt beam and RCC roof and one run of 4Sqmm PVC insulated unshearthed single core 1100 volts grade multistranded copper conductor cable as earth continuity conduto9r and connceting with suitable size thimble complete all as specified and as directed by Engineer-in-Charge. Note: two run of 4 sqmm size PVC cable , one run of 4 Sqmm size PVC cable as earth wire and one run of PVC conduit shall be measured as one unit length complete all as specifeid and directed.

All as per item No 121 but 2 single core 6 Sqmm PVC copper conductor including 1 runs of 6 Sqmm copper conductor as earth wire complete all as specified and as directed by Engineer-in-Charge.

All as per item No 121 above 2 runs of 10 Sqmm PVC copper conductor including 1 runs of 10 Sqmm copper conductor as earth wire complete all as specified and as directed by Engineer-in-Charge.

S&F Rigid non-metallic PVC conduit of size 25 mm exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and as directed by Engineer-in-Charge.

M&L for earthing complete with galvanised steel earth plate elctrode 60 x 60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth strip 25 x 4 mm as earthing lead by means of bolts nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.point 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and as directed by Engineer-in-Charge.

S&F LED light fitting 1 x 20 Watt, 120 Lumen/Watt 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F LED light fitting mirror type with high output diffuser 2 feet 10 Watt, 100 Lumen/Watt 220V, AC decorative type with driver, holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F wall mounted air circulator fan heavy duty of sweep size 400mm, 1400 RPM, single phase, 220-240 Volts, 50 Hz, complete with all fixing/ hanging arrangements directed by manufacturer on wall or as existing working spot including provision of PVC flexible copper cable of suitable size/ length as reqquired complete all as specified. Make- Havells, Cat Part No- FHWGGST-WLG16 or equivalent of any other make in the list of approved manufacturer.

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 8 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified.

S&F MCB SPN, 32Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning all as specified.

Material and labour for point wiring flame proof complete with 1.5 Sqmm single core sheathed PVC insulated FRLSH cable 1100 V grade multistranded copper conductor of code red, blue and yellow for phase, black for neutral and green for earth of ISI marked drawn through and including In stove Enamelled Steel Conduit not less than 20mm dia size with accessories ISI marked concealed in wall/ceiling / roof ncluding PVC insulated copper cable for earth continuity conductor of same type and size and connected to earth dolly of flame proof rotary switch complete all as specified and as directed. Note:- (i) Cutting chases for laying of conduit and sunken boxes, brass screw, washermaking good to walls, floor etc will be included in the above quoted rates. (ii) All fittings junction boxes, conduit pipe and conduit accessories shall be flame proof and totally enclosed IP-65 protection and certified by CMRI Dhanbad also included in above rates. (iii) All flame proof items shall be got tested and certified as "totally enclosed" as suitable for use in explosive buildings on completion by the "Director, central mining research institute (CMRI) Dhanbad. The testing charges and arranging tools, plants, testing equipments etc shall be the responsibility of contractor. (iv) Flame proof rotary switch will be measured and paid separately.

Supply and fix Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specifeid and directed.

Supply and fixing LED light fitting 1 x 16 Watt flame proof greater than 120 Lumen/Watt, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass, with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flame proof FRLSH flexible copper conductor cable with suitable size complete all as specifeid and directed.

S&F Flame proof exhaust fans single phase, 230V, 50Hz, of 380mm sweep, 1440 RPM, including Louvers, Bird Catcher & Mesh Front, approved by CMRI. Make- Simex or Sudhir

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified.

S&F MCB SPN, 32Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning all as specified.

M&L for Sub main wiring with two single core 2x6 sqmm FRLSH insulated and unsheathed stranded copper conductor alongwith earth wire 6.0 sqmm drawn and including In stove Enamelled Steel Conduit not less than 20mm dia size with accessories ISI marked concealed in wall/ceiling / roof connected to main board complete all as specified and directed (Two runs cable and one number earth wire and suitable FRLSH conduit shall measured together as unit length).

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. Provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC (1:3:6) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. Excavation in soft/ loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009).

M/L submain wiring with 2 single core 16 Sqmm PVC insulated unsheathed multistranded copper conductor cable 1100 volt grade drawn throgh and including suitable size PVC rigid conduit inculding necessary PVC conduit specials and one run of 10mm PVC insulated unshearthed single core 1100 volts grade multistranded copper conductor cable as earth continuity condutor and connceting with suitable size thimble complete allas specified and as directed. Note: two run of 16 sqmm size PVC cable , one run of 10 Sqmm size PVC cable as earth wire and one run of PVC conduit shall be measured as one unit length complete all as specifeid and directed.

S&F MCB DB 2 way with out bus bar 240 Volt, for MCB single door complete all as specified and as directed

S&F MCB SPN 63 Amps 240 Volts complete all as specified and as directed.

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 40 mm dia complete all as specified and directed.

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 25 mm dia complete all as specified and directed.

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 20 mm dia complete all as specified and directed.

S/F CPVC Ball Valve of size 40 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed.

S/F CPVC Ball Valve of size 25 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed.

S/F CPVC Ball Valve of size 20 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed.

Supply and fixing of Bib tap CP, Quarter turn with flange and areator, fancy type Long body cast copper alloy with crutch or butterfly handle screwed for GI/cpvc pipe of size 15mm , complete all as specified and as directed by the Engineer-in-charge.(Make : Model No F1099152 of Cera or equivalent to any other make in the approved manufactures list.)

Supply and fixing of Bip cock , CP quarter turn with flange and areator, fancy type short body cast copper alloy with crutch or butterfly handle screwed for GI/ CPVC pipe of size 15 mm complete all as specified and as directed by the Engineer-in-charge.(Make : Model No F2008151 of Cera or equivalent to any other make in the approved manufactures list.)

Supply and fixing 15mm angle valve,quater turn with flange, with flange type chromium plated for fixing with CPVC pipe complete specified and as directed by the Engineer-in-charge.(Make : Model No: F1016201 of Cera or equivalent to any other make in the approved manufactures list.)

Supply and fixing two way angle cock with flange 15 mm, chromium plated for fixing with CPVC pipe complete specified and as directed by the Engineer-in-charge.(Make : Model No: F1017211 of Cera or equivalent to any other make in the approved manufactures list.)

Supply and fixing health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe ,all as per specified and directed (Make : Model No: F8030109AB of Cera or equivalent to any other make in the approved manufactures list.)

Supply and fixing of swivel overhead shower of PTMT any colour with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange for fixing with CPVC pipe and all as specified and as directed by the Engineer -in-Charge. Cat Part No. F7020101 of Cera or equivalent of any other make in the list of approved manufacturer.

Supply and fixing CP angle cock, self closers/ pressmatic with wall flange for urinal pots to fixed in 20/15mm pipe, complete all as specified and directed by the Engineer -in-charge (Model No F9020203 of CERA or equivalent to any other make in the approved manufactures list.)

M&L for repairs to concealed stop cock for Bib taps , Garden Taps, Angle Valves, two way bib cock by replacing the brass spindle screws, nuts & caps etc. all as per site requirement as directed. Make : CERA Model No. F2002362 or any other manufactures from the approved price list

Supply and fixing PVC connection pipe 16mm dia (outer 450mm long cold water complete with brass union on both sides to suit 15mm pipe complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in replacement of Rotational mouldede polyethylene water storage tanks (cylinderical vertical with closed top) hoisted & fixed in position of capacity 1000 liters including inlet, outlet, over flow wash out and Air pipe conncetions. Make : Sintex (ISI) or equivalent to any other make in the approved manufactures list.

Supply and fixing in replacement of Rotational mouldede polyethylene water storage tanks (cylinderical vertical with closed top) hoisted & fixed in position of capacity 500 liters including inlet, outlet, over flow wash out and Air pipe conncetions. Make : Sintex (ISI) or equivalent to any other make in the approved manufactures list.

S/F float valve synthetic(PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut complete all as specified and directed.

Taking down old GI/ CPVC pipe of size 40 mm complete all as specified and as directed.

Taking down old GI/ CPVC pipe of size 25 mm complete all as specified and as directed.

Taking down old GI/ CPVC pipe of size 20 mm complete all as specified and as directed.

Taking down old CPVC ball valve of size 20 mm /25 mm/40mm complete all as specified and directed.

Taking down old bib tap, angle valve, health faucet, angle cock, shower, self closer, stop cock, two way angle cock complete all as specified and as directed.

Taking down old rotational moulded polythene water storage tanks of capacity 1000 ltrs/ 500 litres complete all as specified and as directed.

Taking down old float valve of 25 mm dia complete all as specified and as directed.

Taking down old PVC connection complete all as specified and as directed.

S&F pillar taps, half turn with areator, cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed for 15mm bore pipe complete all as speified and directed. Make- Cera or equivalent of any other make in the list of approved manufacturer.

Yesgee Projects Private Limited

JESWIN BUILDERS