PROVISION OF PATHWAYALONG INTERNAL ROAD OF MSI, SPECIAL REPAIRS TO COMPOUND FENCE OF MSI BLDG NO P-498 TO SHOPPING CENTER AND SDC P566 AND OVER HEAD SHED ANS PATHWAY ON P- 297 OTM AND P300 (CH ) AT INFANTRY LINES MIL STN JAMNAGAR (JOB NO MW07, 08/SRW

Amount

Dismantling of MS work of any description not otherwise provided for complete all as specified and as directed

S& F Rolled sections as in main and cross beams, hip and jack rafters; purlins ,Box section where connected to common rafters and running rails and guides for sliding doors, fencing fixed with angle cleats or other connecting plates including all necessary nut and bolts in Fe 410-w (Gde E-250) Quality A

Demolition of brick work or stone/boulder masonry built in cement mortor or cement lime mortor incl all quoins,arches,pillars , necsessay excavtion and filling etc all as specified and directed

M&L Pre cast cement concrete block type C1in 1:3:6 Using 20 mm graded stone aggregate exc 10 CM in widdth and setting in CM 1;6 all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on the external surfaces of brick work/Strone or concrete surface finishing fair and even without using extra cement.

M&L for preparation of surfaces plastered or unplastered new surfaces on walls and applying two coats of cement base paint complete all as specified .

M&L PCC (1:3:6) C-2, using 40mm graded stone aggregate in foundation, filling and mass concrete.

Dismantling plain or corrugated steel sheeting any gauge thickness including nainital or similar pattern roof coverings

M&F High tensile galvalume sheets colour coated single skin high rib / multi rib TMP Profile Galvalume sheeting in roof having 1000-1020 mm width 28 mm high crest @ maximum 250 mm pitch (centre to centre) and minimum 190mm manufactured out of 0.50 mm TCT (total coated thickness) cold rolled steel, having yield strength 550MPa minimum and wall coated with 25 micron modified polyester paint system applied on Zincalume on top and with back coating on sheet shall be 7-10 micron epoxy paint. The sheet shall be supplied in length maximum upto 6-12 meters long to suit with structural dimensions and fixed with self tapping screws with built in gasket (with bitumen washer) of suitable size machine fixed as per manufacturer instructions and applying adhesive compound to joint overlap of sheets complete all as specified and directed by Engineer-in-Charge.

Dismantling or fencing wire mesh any type

S& Fixing chain link MS galvanised fencing of mesh size 75x75mm 3or4mm including line wires, any mesh to any type of standards,rails,straing bolts,etc. Including provision of binding wire

M&L for preparation of new steel surfaces exc 10 cm in width or girth and applying 2 coats synthetic enamel paint over a coat of red oxide/zinc primer.

M & L Surface excavation not exceeding 30cm deep and averaging 15 cm and gettingout in soft /loose soil.

Removing excavated material to distance not exc 50 m and depositing where directed at a level not exc 1.5m above the starting point.

M&L hard core broken stone or boulders of 63mm gauge, deposited spread and leveled in layers not exceeding 15cm thick watered and well rammed to a true surfaces all as specified and as directed.

S&F Machine pressed precat concrete interlocking paver block (coloured) any shape and size conforming to IS 15658-2006 of 60mm thick M-35 grade etc complete (with grey cement and pigment) over 50 mm thick sand coushioning complete all as specified and directed.

M&Lfactory made hydraulically pressed chequred PCC tiles of size 300x300x25 mm thick and as directed by Engineer-in-Charge laid over & including cement mortar screed 15mm thick in CM 1:4 and jointed, pointed in CM 1:3 complete all as per directed by engineer-in-charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete al as specified and as directed

M&L for cement concrete type B0 1:2:4 ( 12.5mm graded aggregate) in kerb stone , rounded or chamfered on edges set in CM 1:6complete all as specified and as directed.

Excavating in post holes (or similar holes) in any type of soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,watering and removing surplus sol to a distance n exc 50m and making good surface

S&F Joists, channel,angle,or tee flat or box section fixed independently, without connecting plates, etc.(cut to ordinary lengths i.e. within 20 mm of the length indicated ) S & F rolled mild steel Fe - 410-W (Gde-E-250) quality "A".all as specified and as directed.

M&F High tensile galvalume sheets colour coated single skin plain Galvalume sheeting in ridge and cladding having 1000-1020 mm width manufactured out of 0.50 mm TCT (total coated thickness) cold rolled steel, having yield strength 550MPa minimum and wall coated with 25 micron modified polyester paint system applied on Zincalume on top and with back coating on sheet shall be 7-10 micron epoxy paint. The sheet shall be supplied in length maximum upto 6-12 meters long to suit with structural dimensions and fixed with self tapping screws with built in gasket (with bitumen washer) of suitable size machine fixed as per manufacturer instructions and applying adhesive compound to joint overlap of sheets complete all as specified and directed by Engineer-in-Charge.

Krishna Bhoomi Enterprise

ABR Trading Co

Badri Electricals

SURAJ ENTERPRISE