Proposed construction of 08 Nos staff quarters Type II 06 Nos and Type III 02 Nos at Taidu PHC Gomati District 2nd Call

(A) S.H. EARTH WORK Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. - All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. -All kinds of soil

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth, under floor, foundations etc. With sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

Supplying chemical emulsion in sealed containers including delivery as specified. (i) Chlorpyriphos/Lindane emulsifiable concentrate of 20%

Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: (i) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

(B) S.H. CONCRETE WORK Providing and Laying in position cement concrete of specified grade excluding the cost of centring and shuttering- (A) All work upto plinth level: (i) 1:4: 8 (1 cement :4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size).

ii) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 40 mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

(C) S.H. REINFORCED CEMENT CONCRETE WORK Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement. -All work upto plinth level: (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size )

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size).

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (i) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. (i) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering shuttering including struttings, propping etc. and removal of form work for: (i) Foundations, footings, bases for columns etc. for mass concrete with timber plank

ii) Suspended floors, roofs, landings, balconies and access platform with timber plank.

iii) Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply

iv) Weather shade, Chajjas, corbels etc., including edges.

v) Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank

vi) Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply

vii) Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank

viii) Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply

ix) Stairs (excluding landings) except spiral-staircases with wooden plank

x) Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

xi) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply

(D) S.H. BRICK WORK First class brick work in foundation and plinth including cost of all materials as required complete: (i) In cement mortar 1:6 ( 1 cement : 6 fine sand )

First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- (i) In cement mortar 1:6 ( 1 cement : 6 fine sand ).

Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete: (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ).

(E) S.H: ALUMINIUM WORK Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer­in­charge. (Glazing and paneling and dash fasteners to be paid for separately) : (A) For fixed portion of approved quality:- (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

B) For shutters/ sliding shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber/ neoprene gasket required ( Fittings shall be paid for separately ):- (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition frames with EPDM rubber/ neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge :-(Cost of snap beading shall be paid in basic item.) (i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm )

(F) S.H: STEEL, WOOD & PVC WORK Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. (i) Fixing with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 river sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters. (i)35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. (i) Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing chromium plated brass handles with necessary screws etc. complete: (i) 125 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : (i) 300x10 mm

ii) 100x10 mm

Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc. complete (i) 300×16 mm

Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws.

Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter).

(G) S.H. FLOORING WORK Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 -2017 of approved make in colours such as White, Ivory,Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. (A) Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles. (i) 300 mm x 300 mm in all shades and designs

Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and, conforming to IS: 15622 - 2017of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge. (A) Soluble Salt Stainfree vitrified tiles (Glossy) (i) Size of tile 600 mm x 600 mm

Providing and fixing Marble stone in floors over 20 mmthick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge. (A) )14 mm thick Marble stone (i) Raj Nagar plain marble

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. i)450 mm X 300 mm in all shades and design

Providing and laying factory made chamfered edge cement concrete paver block of required strenght thickness and size shape made by table vibratory method to attain superior smooth finish using PU or equivalent moulds laid in required grey color and pattern over and including 50 mm thick compacted bed of sand, compacting and and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator , filling the joints with fine sand and cutting of paver blocks as per required size and pattern finishing and sweeping extra sand in footpath, parks lawns drive ways or light traffic , parking etc all complete as per specification & approval / direction of Er in charge.(a) 60 mm thick C.C. paver block of M-35 grade with approved color design and pattern.

Providing and fixing chequered terrazo tiles 22 mm thick with graded marble chips of size upto 6 mm, laid on floors, footpath & courtyard on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing etc. all complete as per direction of Engineer-in-charge. (i) Dark shade pigment using ordinary cement

(H) S.H. FINISHING WORK 12 mm cement plaster of mix (i) In cement mortar 1 : 6 ( 1 cement : 6 fine sand )

15 mm cement plaster on the rough side of single or half brick wall of mix: (i) In cement mortar 1 : 6 ( 1 cement : 6 fine sand )

6 mm cement plaster of mix : (i) Cement mortar 1:3 (1 cement : 3 fine sand)

12 mm cement plaster of mix (i) In cement mortar 1 : 4 ( 1 cement : 4 fine sand )

Neat cement punning.

Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture, of required shade and colour complete, as per manufacurer's specification. [Payment shall be made after submission of Test Certificate issued by the Manufacturer]. i)Two or more coats on new work.

Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ).

ii) With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: (i)Two or more coats on new work

(I) S.H. WATER PROOFING WORK Grading roof for water proofing treatment [Payment shall be made after submission of the product performance shall carry guaranteed for 7 years against any leakage] complete as required as per direction of the Engineer-in-charge with : i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size)

(J) S.H. SANITARY INSTALLATION AND WATER SUPPLY WORK Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : (i) White Vitreous China Flat back wash basin size 630x450 mm with single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: (A) Kitchen sink without drain board. (i) 610x460 mm bowl depth 200 mm.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 100 mm diameter

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (A) Semi rigid pipe (i) 32 mm dia

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved 450mm long towel rail with total length of 495mm, 78mm wide and effective height quality and colour. (i) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.

Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg /cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: A) Single socketed pipe-110 mm OD.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. (i) 110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: (i)Coupler-110mm

ii)Single equal tee without door -110x110x110mm

iii)Single equal tee with door-110x110x110mm

iv)Bend 87.5° -110mm

v)Terminal guard -110 mm

Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete.-i)100 mm

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 (i) 15 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall (i) 15 mm nominal outer dia .Pipes.

ii) 20 mm nominal outer dia .Pipes.

iii) 25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work (i) 25 mm nominal outer dia .Pipes.

ii) 32 mm dia. nominal outer dia .Pipes.

iii) 40 mm dia. nominal outer dia .Pipes.

Providing and fixing brass stop cock of approved quality : (i) 15 mm nominal bore

ii) 20 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : (A) 45 cm length (i) 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge : Single socketed pipe - 110 mm OD

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type-A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge : (i)Coupler-110 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete as per direction of Engineer-in-charge. (i)110mm

Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. etc. complete as per direction of Engineer-in-charge. (i) 100 mm

(K) S.H. DEEP TUBE WELL Drilling and boring pilot hole in any soil strata by manual means, collection of soil samples of different strata met with during drilling at various suitable levels, preservation of samples in polythene bags / sample boxes and disposal of excess soil or mud, including the cost for water etc. as required to maintain the pilot hole properly as per specification and direction of the Engineer - in - charge. (i) 100 mm

Reaming of pilot hole to an enlarged bore hole in any soil strata bby manual means, disposal of excess soil or mud, including the cost for water etc. As required to maintain the bore hole properly as per specification and direction of the Engineer-in-charge. i) from 100 mm dia pilot hole to 250 mm bore hole

Washing and development of tube well by using hand pump or by any suitable method and testing of the well as per specification and direction of the Engineer-in-charge.

Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer-in-charge.UPVC CM Casing pipe (i) 150 mm dia

UPVC RS Pipe (i) 150 mm dia

UPVC RS Pipe (i) 100 mm dia

Providing fixing of UPVC end cap / well suitable for UPVC 'CM' casing or 'CS' casing or 'RS' pipes as per specification and direction of the Engineer in charge.

Providing and shrounding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) and direction of the Engineer-in-charge. With Contractor's rig i) Pea gravels obtained deom Durgapur, West Bengal.

Providing and fitting fixing with PVC insulated 3 core flat Copper cable conforming to relevant IS code for submerssible motor with all necessary equipments and fittings as required as per specification and direction of the Engineer-in-charge. (i) 2.5 Sqmm

Providing and fixing G.I bend / elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer in charge. (a) 40 mm dia

Supplying and fitting fixing of single phase motor starter panel unit 3 HP capacity comprising with 2 pole conductor , over load relay capacitor , voltsmeter and amp meter of BCH/L&T mark with necessary copper wire etc complete as per direction of engineer in charge.

Supplying & installation of water libricated Submersible pump having ISI marked capacity 1000 GPH at total head upto 60mtr cuple with submersible motor 2 HP suitable for 240 voltas (+10% variation single phase 50HP AC supply DOL starting method to run at 2880 RPM along with 35 mtr 2.5 Sqm pvc insulated 3 ( three) core flat copper cables including fitting fixing and lowering it with 40 mm dia G.I pipe upto 100 Ft (30.00 mtr) etc complete as per direction of the Engg In Charge .(40 mm GI pipe and fittings will be paid separately).

Please Enable Macros to View BoQ information