SPL REPAIR TO BLDG NOS A-14, P-54 AND PROVN OF ONE TOILET BLOCK AND OTHER MISCELLANEOUS WORKS AT MIL STN DHARCHULA.

Amount

DESCRIPTION OF ITEMS

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5M in depth for foundation etc and getting out in hard/dense soil complete all as specified and as directed.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in harde/dense soil complete all as specified and as directed.

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm (hard/dense soil) complete all as specified and as directed.

Filling under floor (except material) including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified. (Note- Material obtained from excavation items will be used in filling).

Removing excavated material (soils) n .exc 50 m and depositing, where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed.

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface complete all as specified and as directed. (Area of the substructure in contact with backfill to be measured)

M&L for treating top surface of filled earth at the rate of 5 litre per sqm of surface with anti termite chemical emulsion complete all as specified.

M&L for treating the soil under plinth protection at the rate of 5 litre per sqm of surface with anti termite chemical emulsion complete all as specified.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of anti termite chemical emulsion per sqm of the perimeter wall complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M&L RCC M-25 (Design Mix) as in foundation, including raft, footings, foundation beams, plinth beams, bases for columns etc complete all as specified.

M&L RCC M-25 (Design Mix) as in columns, pillars, piers etc complete all as specified and as directed.

M&L RCC M-25 (Design Mix) as in beams, cantilever, lintels,chajja etc complete all as specified and as directed.

M&L RCC M-25 (Design Mix) as in slabs supported on walls, beams and columns etc complete all as specified and as directed.

M&L form work to sides and soffits of roof beams, lintels lever shelves,chajjas incl supports over hang etc ruogh finished surfaces of concrete flat all as specified.

M&L form work to soffits of suspended slabs such as roof slab landings and similar works n exc 200mm thick (horizontal or slopping) for rough finished surfaces of concrete flat all as specified.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

M&L form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams or similar works vertical or to batter for rough finished surface of concrete complete all as specified and as directed.

M&L form work to sides of pillars, posts, struts, columns for rough finished surface of concrete complete all as specified and as directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to all as specified.

ditto as sl item no 20 above but, 5 mm dia and over and incl 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

M&L for Pre-cast cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed.

M & L Rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

M & L Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

M & L Rendering 5mm thick in CM (1:3) on fair faces of brick work or concrete surfaces as in ceilling to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for hard core of broken stone or boulders gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface of broken bricks aggregate, all as specified.

M&L PCC 40mm thick 1:2:4 of type B1 using 20mm graded stone aggregate as in subbase of floor complete all as specified and as directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer of cement (1:6) complete all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm to 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6, type C-2, as in pavings/hard standing/path/Plinth protection etc finished even & smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 metre and at change in direction complete all as specified & directed.

S&F for mild steel framed wk as in doors or gates of angle iron or other section complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with & incl either hooks & hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and slides) & hanging, also fastening & fixing Fe-290, Gde-165 complete all as spfd & directed.

S&F 1.00 mm th Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams,including bending or turning up, mitred angles, etc. as required complete all as spfd & directed.

S&F 35 mm th Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L for 2nd class hardwood, 35 mm thick glazed and skelton shutter, open rebated and prepared to receive glass, gauge, etc. devided into squares, with plain, chamfered or rounded , mitred and rebated shash bars any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc; size of members of shutter as specified in SSR Part I, Sectioin 8 clause 8.24(a); supplied and fitted to chowkhat complete all as specified and directed

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and directed.

S&F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and as directed.

S&F 150 mm aluminium handles, cast type anodised complete all as specified and directed.

S&F150 mm aluminium anodised barrel tower bolts extruded section complete all as specified and as directed.

S&F 150 mm Mild Steel barrel tower bolts, stove enamelled, black with bright bolts complete all as specified and as directed.

S&F 250mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F 250-300mm, ordinary rat tail rod pattern springs including roller and roller plate ccomplete all as specified and as directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceilling complete all as specified and as directed.

M&L three coats of white wash on walls including preparation on new plastered surface and complete all as specified and as directed.

M&L for two coat of synthetic enamel paint over a coat of pink primer to new/old wooden surface of any description exc 10 cm girth or width including prepration of new/old wooden surfaces complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces of any description over 10 cm in width or girth incl preparation of new steel surfaces complete all as spfd and directed.

S&F stop valve/angle valve, bore of dia 15mm of Chromium plated fancy type cast copper alloy screwed down for iron pipe and fixed etc complete all as specified and directed.

S&F 15mm bore Chromium plated Bib taps fancy type, cast copper alloy screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F Tubular towel rail brass chromium plated 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F CP Towel Ring fixed with and including Chromium plated brass screws and cleats complete all as specified and as directed.

S&F 15mm dia Brass CP mixer fancy type for mixing hot & cold water incl bend pipe for provision of overhead shower screwed down for iron pipe and fixed complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450mm long all as spfd and as directed.

S&F Brass chromium plated shower rose 125mm size incl shower arm 15mm dia complete all as spfd & directed

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Cutting chases in brick wall, stone concrete block or slab walls, pining in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings ,steps,cills sunshades, shelves , lintels, etc and cutting chases for concealed water tubing and making good , cutting n'exc 10 cm girth complete all as specified and directed.

S&F 15 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc complete all as specified and as directed.

S&F 20 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc complete all as specified and as directed.

S&F in vitreous china wash basin of size 550x400mm white flat back with full pedestal of height 800 to 830mm, incl 32mm size chromium plated waste fitting and waste pipe fixed to wall with fastener/rawl plugs complete all as specified and directed.

S&F Vitreous China Wash down water closet pan pedastel pattern (EWC) white in colour with and incl plastic seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device and P or S trap incl connection to outgoing pipe and flushing pipe complete all as specified and directed.

S&F vitreous china squatting pan "Orissa pattern" size 580 mm x 440 mm white with integral foot rests and P or S trap, incl provn of lime concrete bedding complete all as spfd & directed.

S&F for PVC low level flushing cistern 10ltr capacity, with cyphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc incl PVC connection 450mm long as spd and fixed all as specified and directed

Supply and fix 1000 Ltr rotational moulded polyethylene water stotage tanks ( cylinderical vetrticle with closed top) hoisted & fixed in position incl 20mm dia Ball brass valves,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F 75mm bore PVC(SWR) Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/wall complete as all spfd and directed

S&F 110 mm bore PVC(SWR) Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/wall complete as all spfd and directed

S&F 75 mm bore PVC(SWR) bends/Tee any radius complete all as specified and directed

S&F 110 mm bore PVC(SWR) bends/Tee any radius complete all as specified and directed

S&F 100 mm dia CP grating doom with or without waste hole min wt 25g . grating for bathroom and kitchen etc complete all as spfd and as directed all as specified and as directed

S&F PVC (SWR) floor trap including jointing to waste pipe 100 mm bore outlet with solvent cement all as specified.

M & L water proofing treatment on existing roof with the following speification complete (a) 15mm thick cement plaster in CM 1:4 neeru finished. (b) Apply bituminous primer @ 0.5 Ltr/Sqm confirming to IS 3384-1965 on prepared surface till the surface is properly pregnated.(c) Apply hot bitumen 85/25 grade @ 1.2 Kgs/Sqm confirming to IS 702-1988. (d) Laying APP based polimeric water proofing membrane minimum weight not less than 3.0 Kg/Sqm and minimum 2 mm thick reinforced with polyster non wove fabric (Wt not less than 150 gms/sqm) laid on primed surface by forced application complete with as per manufacturer instructions confirming to IS complete all as specified and directed. (e) Applying a coat aluminium paint min. 0.20ltr/sqm as per manufacturer's instructions.

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed.

M&L cement concrete type B-1, PCC 1:2:4 (20mm graded agg) as in coping,kerbs etc. complete all as specified and directed

M & L cement concrete 1:2:4 type B1(20mm aggregate) in surface channel complete all as specified and directed.

M&L for precast cement concrete type B1 1:2:4 (Using 20 mm graded stone aggregate) as in cover slabs, manhole cover, chamber cover and drainge cover set in cement mortar 1:6 including necessary formwok complete all as specified and directed.

S&F reinforced concrete pipes, class NP2,150mm dla laid and jointed complete with collars, complete all as specified and directed.

M&L for concrete bed 1:4:8 type D-2 (Using 40 mm graded stone aggregate) as in drain pipes including packing under, and haunching against the side of pipes after the are laid and tested for 150 mm bore pipe, complete all as specified and directed.

Excavation over areas n.exc. 1.5m deep and getting out in hard dense soil including removal of excavated material n.exc 50m and depositing where directed at a level n.exc. 1.5m above the starting point

M&L cement concrete type E-2, PCC 1:5:10 (40mm graded agg) as in foundation,filling and mass concrete complete all as directed

M&L 50mm thick cement concrete type B-1, PCC 1:2:4 (20mm graded agg) as directed

M & L for providing coloured chequered cement concrete tiles of size 30cm x 30cm x 20-25mm thick set & jointed in neat cement slurry with grey cement and pigment including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of chequered tile complete all as specified and directed.

M&L for Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.Fe410-0 Gde E-250 Quality A complete all as specified and as directed.

Demolition of cement concrete in ground floor,paving nexc 15cm thick(below or above GL) complete all as specified and directed

Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of 100m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and as directed.

Providing cement concrete 100 mm thick type B-1 (1:2:4) using 20 mm graded agg incl floor hardner as in floor, finishing cement concrete surface even and rough incl providing necessary joints complete all as specified and directed . (Note : Floor hardener shall be measured and paid separately as supply only item.)

Supply only non- metallic floor hardener applied over concrete surface as per manufacturer's instructions complete all as specified & directed by Engr-In-Charge

Demolition of brick work, stone/boulder masonary built in cement mortar complete all speecified and directed

M&L for brick work with sub class 'B' brick old size bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as spfd & directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6, complete all as specified.

Taking down cement plaster on brick or stone walls, of any description including raking out joints, hacking for key, scrubbing down with water, etc complete all as spfd and directed.

M&L for Preparing new plastered wall surfaces and applying two coat of oil emulsion distemper over primer over wall putty of 1mm thckness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for Preparing old surfaces, plastered or unplasterd old decorated wall surfaces and applying two coat of oil emulsion distemper over a coat of wall putty of 1mm thckness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less that 50gm/liter and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter / 10 Sqm over and including priming coat of exterior primer applied @0.90 liter/10 Sqm over new surfaces over 1 mm thick wall putty complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete in floors over and including 15mm thick screed in CM 1:6 etc complete all as spfd & directed

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, in skirting over and including 10mm thick screed in CM 1:4 etc set complete all as spfd & directed

M&L for non-skid ceramic light shade tiles/outdoor tiles 8-10 mm thick (square or rectangular) polished area of each tile not exc.0.18 sqm in floor etc and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade complete laid over screed bed,rendering or bedding layer of mortar CM (1:6) 15mm thick all as specified and directed

M&L for glazed ceramic tiles in vertical surface, 450x350x7-8mm thick set and jointed in neat sement slurry and pointed in white or colour cement to match over 10 mm thick plaster in CM 1:4 complete all as spfd & directed.

M&L Granite (of any type) slab 20 mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed in CM 1:6 etc complete all as specified and as directed

Taking down chowkhats or frame nexc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sqm but nexc 4.00 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

S&F Pressed steel frames 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and as directed.

S&F Pressed steel frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,complete all as specified and as directed.

M&L cement concrete type C1 1:3:6 (20 mm graded stone aggreagte) as in filling inside pressed steel chowkhats complete all as specified and directed.

S&F Steel windows box type section with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded all as spfd and as directed.

-ditto- as sl item no 108 above but without glazing bar

S & F MS work as in window guard bars,holdfasts etc., plain, let in and fixed independently in wooden frames etc, and similar articles conforming to Fe 290 Gde E 165 complete all as specified and directed

S&F for powder coated anodised aluminium frame for doors, windows ventilator with one or more rebates including joining cleat for fixing etc , screws, hinges, brackets, dash fastners/rawl plugs etc. complete all as specified and directed.complete all as specified and directed.

S&F powder coated aluminium door shutters, aluminium section weighing not less than 0.55 Kg/m including necessary jointing cleats glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified and directed.

M&L for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel covr, governing pivo made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floors 150mm long all as specified and as directed.

S&F 4.80 mm thick sheet glass ordinary quality and glazing with oil putty/rubber packing in square exc .50 sqm in each panels complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S&F 100 mm Mortice lock,vertical type,size 100 mm complete all as specified and directed.

S&F 100 mm Mild Steel barrel tower bolts, stove enamelled, black with bright bolts complete all as specified and directed

Dismantling mild steel work of any description and in any position complete all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and gastenings and heavy brackets framing (beam, tee, angle channel or flat sections) (Fe-290 Gde E-165) inicluding distance pieces, cleats etc complete all as specified and as directed.

S&F in repairs vitreous china wash basin,rectangular or oval shaped with min . Size 550X400mm incl 32mm size brass chromium plated waste fittings,waste pipe fixing in slab/granite top incl necessary fixing arrangement complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm th kitchen or laboratory with plugs, washers & waste coupling, incl bedding in CM to dwarf wall or incl fixing cantilever brackets & connecting union to pipe over all size 495x420mm bowl size 410x330 mmx160 mm complete all as spfd & directed.

S & F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connection union to pipe overall size 914 mm x 460 mm ,bowl size 405 mm x 354 mm complete all as specified and directed.

S&F in repair CP Towel Ring fixed with and including Chromium plated brass screws and cleats complete all as specified and directed

S&F in repair 15mm bore Chromium plated Bib taps fancy type, cast copper alloy screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs stop valve/angle valve, bore of dia 15mm of Chromium plated fancy type cast copper alloy screwed down for iron pipe and fixed etc complete all as specified and directed.

S&F in repairs Brass CP mixer fancy type for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F 15 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc including taking up or down 15 mm GI tubing complete all as spfd & directed

S & F in repair Harrison rails/curtain rods, mild steel, chromium plated with brackets,stops, rollers etc fancy type as approved complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets,fittings etc as specified and directed.

S&F False Ceiling Horizontal level regular edge grid 600 x 600 mm form work using hot dip sections and fixing tiles vinyl laminated MPL gypsum panels size 595x595x6 to 8mm thick after lamination, suspended the grid with grid hangers to Roof Truss / RCC Slab all as spfd and directed.

M&L for 18/19mm thickness Medium density fibre board,one side laminated other side balancing, exterior grade, fixed in repair to framework with screws etc complete all as specified and as directed.

S&F 6mm thick teak wood lipping fixed with nails to block board or veneered particle board all as spfd and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised (width of flaps 30mm) all as specified.

S&F 25-40mm dia cupboard knobs fixed with nut, screw and washer of mild steel bright finished complete all as specified and directed.

Dismanteling of timber scantling 40 sqcm and over in section in any position for unframed works complete all as specified and directed

M&L for 2nd class hard wood as in scantling clean sawn framed & fixed as in ceiling and walling wks, complete all spfd & directed.

M&L for one coat of creasote oil to wooden surfaces new or old of any description including prepration of surfaces complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting of any guage/thickness in roof covering/wall clading complete all as spfd and directed

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition reinforced cement concrete in any description and in any position complete all as specified and directed.

M&L Slabs supported on walls,beams and columns in floors,roofs, landings,balconies,canopies, deck slabs and in shelves and the like using cement concrete type B-0 1:2:4 complete all as specified and directed

M & L mild steel TMT bars 6 to 8mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as specified and directed

Extra for forming fair finished drains or channel 30 Cm inner girth in cement concrete , using extra cement including form, moulds, mitred / stopped ends etc complete as specified and directed.

M&L providing kota stone slab 12-16 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed in neat cement slurry and pointed with white or coloured cement to match mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10 mm thick plaster in CM 1:4 in vertical surface complete all as specified and directed by Engr-In-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F 20 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc including taking down old pipe, complete all as spfd & directed

S&F in 1000 Ltr rotational moulded polyethylene water storage tanks ( cylinderical vertical with closed top) hoisted & fixed in position including taking down old tank, complete all as spfd & directed.

S&F in rep Ball brass valves 20mm, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as spfd & directed.

Supply and fix in repairs gun metal, globe or gate vlave 20mm dia bore, screwed both end for iron pipe and fixed complete all as specified and directed

M &L for preparation of plastered or unplastered old decorated surfaces of walls applying one coat of white wash on walls complete all as specified and directed.

All as per Item No. 1 above but applying one coat of white wash on ceiling complete all as specified and directed.

M &L for preparation of plastered or unplastered old decorated surfaces of walls and applying one coat of cement based paint on walls complete all as specified and directed.

M&L for preparation of old plastered surface wall by complete removing old surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engr-In-Charge.

Dismantling /taking out existing hessain base felt or any other existing water proofing treatment from roof including cement plaster and exposing the top surface of RCC slab including removing the dismantled debris to a distance exc 100 m and n.exc 250 m complete all as specified and directed

M&L APP based polymeric membrane minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyster non-woven fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application method with minimum side overlap 100mm and 150mm as end lap overroofs after cleaning the surfaces properly with water and allowed to dry completely including priming surfaces for applying heavy treatment complte all as specified and directed.

M&L rendering 10 mm thick (avg) on concrete surfaces over roof slabs, in cement mortar 1:4 mixed with liquid water proofing compound finished even and smooth using extra cement, to receive roof treatment complete all as specified and directed . (Note - water proofing compound shall be measured and paid saperately)

M&L for surface of any description over 10 cm width or girth not other wise described and applying a coat of aluminium paint.

Supply only liquid water proofing compound.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete incl fittings such as switches, ceiling roses, pendants, regulators, sockets etc and making good disturbed surfaces of walls, floors etc all as specified.

M&L point wiring with 1.5 Sqmm (Nominal cross sectional area) single core PVC insulated with PVC unsheathed multi stranded copper conductor FRLS cable in open/ surface/concealed PVC conduit of suitable size, complete with all accessories/fitting, including heavy duty PVC/ABS terminal switch board floor mounted/flush type (depth not less than 45 mm) of suitable size (lengthX width) for mounting modular switches, Modular sockets, Modular regulators including PVC module top cover plate with frame of suitable size , brass screw and washer including unsheathed single core PVC insulated cable green in colour 1.5 Sqmm multistranded copper conductor as contineous earth wire and connecting to earth dolly complete all as specified for one light point / fan point controlled by one way switch of 5/6 Amps.

All as per item No. 167 above but for one 3/5 pin socket outlet point on same board controlled by one way switch of 5 Amps.

All as per item No. 167 above but for one 3/5 pin socket outlet point on independent board controlled by one way switch of 5 Amps.

M&L point wiring with 2.5 Sqmm (Nominal cross sectional area) single core PVC insulated with PVC unsheathed multi stranded copper conductor FRLS cable in open/ surface/concealed PVC conduit of suitable size, complete with all accessories/fitting, including heavy duty PVC/ABS terminal switch board surface mounted/flush type to wall (depth not less than 45 mm) of suitable size (lengthX width) for mounting modular switches, Modular sockets, Modular regulators including PVC module top cover plate with frame of suitable size , brass screw and washer including unsheathed single core PVC insulated cable green in colour 2.5 Sqmm multistranded copper conductor as contineous earth wire and connecting to earth dolly complete all as specified for 15/16 amp socket outlet point controlled by one , one way switch of 15/16 Amps complete all as specified.

S&F Modular switch 1 module single pole one way 6 Amps, 240 volt complete all as specified.

S&F Modular switch 1 module single pole one way 16 Amps, 240 volt complete all as specified.

S&F Modular socket outletn, 2 module, 3 pin 5/6 Amps, 240 volt complete all as specified.

S&F Modular socket out let, 2 module, two in one 3 pin 5/6 Amps and 3 pin 15/16 amp , 240 volt, complete all as specified.

S&F ceiling rose, surface bakelite, AC, 60x30mm, 3 terminals complete all as specified.

S&F lamp holder PVC /poly carbonated type with back plate suitable for pendants /angular /batten fittings complete all as specified.

S&F stepped type electronic fan regulator modular type ,2 module,240 volt complete all as specified.

S&F in replacement 20W surface / wall mounted box type batten LED luminaire having extruded Polycarbonate housing and PC diffuser (bright white/warm white) and integrated electronic driver with high efficiency, CRI = 80 (Minimum), PF ≥ 0.90, luminous efficacy ≥ 100 lumens/Watt operating voltage 140V-240V, CCT≥5700+/-300K complete with mounting accessories internally prewired and including connecting up with cordflexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED Bulb/LED retrofit 'T' bulb 12 watts, B22 end cap complete all as specified.

Suppy and Fixing inverter LED Bulb 12 B 22 watt having backup minimum three hours complete all as specified and as directed.

S&F in replacement LED bldg security lights of 35 Watt having pressure die cast aluminium housing with system lumens efficacy≥100 lumen/W, IP65 protection, IK07 rating, inbuilt electronic driver with PF>0.95 and mounting on GI bracket incl connecting up with three core twisted flexible copper conductor cable complete all as specified and directed

Supply and fixing in replacement security light bracket made out of light grade 25 to 32mm dia GI pipe of length 0.9 mtr bend to shape and mounting on wall using clamps nut bolts etc complete all as specified and directed.

S&F in replacement Energy saving, surface mounted, bulk head LED luminaire 10/12 W with Polycarbonate housing and diffuser complete including connecting up with cord flexible copper conductor cable of suitable size complete all as specified an directed.

Supply and fixing LED luminaire 600 mm x 600 mm panel warm white/white , 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, suitable for roof ceiling including connecting up with driver including flexible copper wiere of suitable size complete all as specified.

S&F sheet metal enclosure for DB TPN 4 way with 200 Amp rated bus bar 415 Volts,double door suitable for housing MCBs and SPN complete all as specified.

S&F sheet metal enclosure for DB SPN 8 way with 200 Amp rated bus bar 240 Volts, Double door suitable for housing MCBs and isolators complete all as specified and directed

S&F sheet metal enclosure for DB SPN 2 way with 200 Amp rated bus bar 240 Volts, Double door suitable for housing MCBs and isolators complete all as specified and directed

S & F SPN MCB DB 4 way sheet metal enclosures double door 230 V AC, 50 Hz AC with IP 43 and IK 09 rating having fully insulated copper busbar of rating not less than 100Amps, insulated neutral bar, earth bar and cable ties for cable management complete all as specified and directed.

Supply and fixing miniature circuit breaker (MCB) of 4 pole current carrying capacity 32 to 63 Amps Amp, 240V, 10 KA 'B' curve type, in the MCB DB complete with connection testing and commissioning complete all as specified.

S&F MCB SPN 32 Amps, 240volts, 10KA, C Curve complete all as specified and directed.

Supply and fixing miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, 240V, 10 KA 'B' curve type, in the MCB DB complete with connection testing and commissioning complete all as specified.

Material and labour for sub main wiring with 2x6 Sqmm nominal cross sectional area (two single core cable of 6 Sqmm for Phase and neutral + o1 single core cable of 6.0 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 6.0 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed /surface conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dully including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing and taking down the old unserviceable submain wiring of ant type complete all as specified & directed. ( Note - One meter of conduit along with 2x6.0 Sqmm wire and one 6.0 sqmm earth wire shall be measured as one length).

Material and labour for sub main wiring with 2x4 Sqmm nominal cross sectional area (two single core cable of 4 Sqmm for Phase and neutral + o1 single core cable of 4.0 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 4.0 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed /surface conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dully including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing and taking down the old unserviceable submain wiring of ant type complete all as specified & directed. ( Note - One meter of conduit along with 2x4.0 Sqmm wire and one 4.0 sqmm earth wire shall be measured as one length).

Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 4 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 2 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 10 Sqmm 2 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 M depth in soft / loose soil and geting out complete all as specified and directed.

Material and labour for sand cushioning with dry fine sand including filling, spreading, levelling in layers in cable trench with approved quality of sand for protection of under ground cable complete all as specified and directed.

Material and labour for contineous brick edging with width equal to the depth of the brick of whole sub class 'B' bricks laid on edge complete all as specified and directed.

Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in 25mm thick layer complete all as specified and as specified.

Removal of surplus excavated soil to a distance exc50 m but not exc in 100 m and deposited wher directedat a leveln exc 50 m above the starting point complete all as specified.

Supply / laying and fixing 40 mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

Material and Labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level, conneted to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, cheek nuts and washers of galvanised or iron protected by 15 mm bore GI pipe (medium grade) and connected to main switch board as directed including concrete pit in PCC (1:3:6) type C1 precast RCC (1:2:4) type B1 cover slab 40x40 Cm x 6Cm reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifitting made out of 8 mm dia MS bar, funnle, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR part-I, 2009.

Disconnecting electrically, taking down exhaust fan of size upto 450mm sweep from existing position, dismantling frame and blades, servicing by cleaning oiling /greasing, replacing unsv parts reassembling and refixing at same or new locations duly connected with new cordflexible copper conductor cable of size 23/.0076 from ceiling rose and testing complete all as specified & directed. Note: Spare parts other than specified will be measured and paid separately under respective items.

Rewinding of exhaust fan motor of size 450 mm sweep any make with super enamelled copper winding wire of 32SWG gauge, sleeve work, varnishing with `B' class insulation varnish, connection with flexible wire of appropriate size two core copper wire upto connector block including cutting and taking out old burnt Al/Cu winding wire complete all as specified and directed. Note : (i) Rewinding should be done at workshop

Supply and fixing motor of metal exhaust fan 450mm,singlre phase , 50 HZ 230 Volt , heavy duty , minimum 1350 RPM copper wounded all as specified and directed.

Supply & fixing in repair industrial type SPN enclosure with a two pin and earth plug and socket including industrial plug 3 pin 20 Amp, complete with and including 32 Amps MCB, single pole, AC, 240 volts and flush to wall including all cuttings & chases etc on wall of fixed on surface of wall and making good including two coats of white / colour washing / distempering etc to match the existing disturbed surfaces complete all as directed.

Supply and lay pipe galvanised ''medium class'' including fittings of size 20 mm dia bore complete all as specified and as directed.

Supply and lay pipe galvanised ''medium class'' including fittings of size 15 mm dia bore complete all as specified and as directed.

Supply and lay hot water pipe duly insulated with glass wool and aluminium cladding 15 mm bore complete all as specified and as directed.

S&F Gun Metal gate valve with Iron wheel head screwed both ends for GI steel tubing 15mm dia complete all as specified.

S&F in replacement Gun Metal gate valve with Iron wheel head screwed both ends for GI steel tubing 20mm dia including taking down unserviceable valves complete all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V , 50 Hz 1350 RPM of size 380 mm sweep heavy duty with, blades, and frame and louvers complete all as specified and directed.

Cutting existing steel tubing 25 mm dia, screwing for alterations or additions for fittings such as unions, gate valves etc complete all as specified.

Supply, Install, Testing and Commissioning of 'Solar Hot Water System' (Flat Plate Collector type) based on indirect transfer of heat of capacity 100 LPD complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks 250/300 Liters capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including float valve of size 20 mm complete all as specified and as directed.

M&L for mild steel framed wk as in doors or gates of angle iron or other section complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with & incl either hooks & hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rail sand suides) & hanging, also fastening & fixing Fe-290, Gde-165 complete all as spfd & directed.

M/L for two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces of any description over 10 cm in width or girth incl preparation of new steel surfaces complete all as spfd and directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in coping,benching,anchorage blocks, lintels upto 1.5m clear span,cills, steps, sesmic & other similar bands, plinth course, lacing course, parapets & ralling upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs not provided for water trought & the like including weathering, slightly rounded or chemfered angels & throating complete all as directed and specified. @ 9259.40/Cum, SI-04029

Note : Tenderers may note that amount of credit Rs 42,093.88 will be deducted from the total amount arrived, at the time of Acceptance of contract.

M/S TRILOCK SINGH AND SONS CONTRECTOR AND GOVERNMENT SUPPLIERS (BID ID -3519194)

M/S SUNIL KUMAR CONT (BID ID -3519238)

UMED SINGH (BID ID -3508085)