ADDITION/ ALTERATION TO CERTAIN MD ACCN AT 23 ED

Amount

B/R ITEMS

M&L for Plain Cement Concrete 1:5:10 Type E2 using 40 mm graded stone aggregate as in sunken floor filling, etc., complete all as specified and as directed.

M&L for Plain Cement Concrete 1:2:4 Type B0 using 12.5mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M&L for Plain Cement Concrete 1:3:6, Type C1 using 20mm graded stone aggregate as in coping including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and as directed.

M&L for Plain Cement Concrete 1:2:4, Type B0 using 12.5mm graded stone aggregate as in surface channel and drains including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed.

S&F for pre cast reinforced cement concrete cover slab (for man holes) with PCC 1:2:4 Type B1 using 20 mm graded aggregate, set in cement mortar 1:4, complete all as specified and as directed. Note: Reinforcement shall be measured and paid separately under relevant item of this BoQ.

Supply only integral liquid water proofing compound complete all as specified and as directed.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 complete all as specified and as directed.

M&L for Cutting chases or making holes in brick walls for concealed water tubing, making good to facings where required, cutting not exc 10cm girth complete all as specified and as directed.

M&L for Forming jambs, etc., to openings including cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work complete in cement mortar 1:4 all as specified and as directed.

Making good under cills or over arches lintels and bressummers including all pinning when necessary complete in cement mortar 1:4 all as specified and as directed.

Cutting holes in brick walls in cement mortar for inserting hold fasts with depth of embedded portion of holdfasts measured from the face of the jamb into the wall exc. half brick but not exc. one brick and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

M&L for 18-20mm thick Granite stone slab, premium quality, machine cut, water cut, ‘Z’ black type, table rubbed and polished, as in cooking platforms and like laid over and including 20mm thick cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab including rounding the projected edges complete all as specified and as directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete all as specified and as directed.

S&F 30mm thick Factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) edges of framing plain, chamfered or rounded. fitted without and mitred beads or securing glass, etc., sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F 35 mm thick Factory made 2nd class hard wood plain, framed, panelled shutters, any number of panels, with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) n.exc 1.5 sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) exc 1.5 and n.exc 4 sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each and refixing in same opening complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm thick MS square tube of 19 gauge mitre cut at two corners and joined by inserting two Nos of 150mm long brackets of 15mmx15mm MS square tube inside the 19mm MS square tube and suitably screwed complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (styles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification complete all as specified and as directed.

Supplying and installing of pre-fabricated, factory made, modular kitchen cabinet units below the existing kitchen platform/ counter, 750 mm height x 700 mm deep (Approx) as per the following specifications and as per Sketch No. 1 of GE Avadi. [a] The frame work of the cabinets including its shutters, sides, bottom, shelves, drawer fascias, etc. shall be made out of 16 to 18mm thick Marine plywood. All exposed surfaces and internal surfaces of the Cabinet units shall be provided with machine pressed lamination having thickness 1mm and 0.8mm respectively of approved shade and make and pasted with synthetic resin based adhesive. [b] The dimensions of cabinets shall be designed to accommodate the standard sizes of baskets/ thalis/ pullouts/ bin holders, etc., for smooth functioning of units. All shelves shall be supported on approved quality SS pins and shall be adjustable for various height requirements. The unit shall be firmly fixed to the walls/ slabs/ floors using non-corrosive metal screws of appropriate size and rawl plugs.

[c] Each shutter shall be fixed to the framework using two numbers of best quality Euro type Slip/ Auto Hinges and provided with one approved quality profile and brush finished Stainless Steel (SS) handle of grade 304 (minimum 150 mm long). SS baskets / accessories shall be mounted on approved quality, high precision telescopic channels/ slides to be designed as per drawer size and to meet the weight requirement with minimum length of 500 mm to ensure smooth movements of drawer with / without content weights and provided with approved quality 150mm size SS handles of grade 304. [d] The thickness of four edge PVC lipping for shutters and drawer fascia shall be 2mm Thick and the thickness of edge lipping of carcass/ plywood partition shall be 0.8mm. The lippings/banding shall match with the external laminate shade. All faces and edges of Kadappah support slabs below the kitchen slab, wooden planks for supporting telescopic channel rails and wooden fillers shall be painted with a coat of synthetic enamel primer and two coats of white colour synthetic enamel paint.

[e] The wooden frame for shutter shall be made of minimum 70 mm wide marine plywood with lamination, wherever required. The telescopic channel shall be supported with 75 mm wide vertical and horizontal marine plywood BWP Laminate members with laminate fixed on vertical Cuddappah stone slab. If there is a need of erecting additional vertical marine plywood members with laminate on account of site conditions, the quoted rate shall have provision of carrying out these works.

Notes: [i] All the modular kitchen cabinet works shall be carried out by the contractor through skilled tradesmen with standard Engineering practice and workmanship. [ii] Payment shall be made on the basis of front elevation area of modular units only. It is clarified that sides, top and bottom surfaces will not be measured for payment. [iii] The quoted rate shall include making of vertical partition below the existing kitchen slab with 16 to 18 mm thick marine plywood, if necessary, to accommodate modular kitchen units as per the requirement [iv] All necessary hardware, wooden members with required thickness for fixing telescopic channel rails and filling the gaps shall be included in the quoted rate.

[iv] In each kitchen the following minimum accessories shall be required to be provided. Accordingly the modular kitchen cabinet units shall be designed and prior approval of GE shall be obtained for design/ pattern/ colour shades, etc. before commencing the modular kitchen cabinet works. The following cutleries/ Thalis/ pullouts/ baskets/ bin holders, etc. shall be measured and paid separately under relevant items of BoQ:- [a] Perforated Cutlery basket (4" size) – 1 No. [b] Cup & saucer basket (6" size) – 1 No. [c] Thali basket (8" size) – 1 No. [d] Plain multipurpose baskets (8" size) – 4 Nos. [e] Three tier oil/masala Pull out – 1 No. [f ] Two tier detergent Pull out – 1 No. [g] Shutters below the sink with Dia 250mm x Height 145mm bin 1 No. [h] Foldable shutter at the mid corner portion for gas cylinder – 1 No. [j ] Plain shutters each at both wall 1 and wall 2 – 2 Nos..

Makes:- [i] Basket & accessories/ Telescopic channels/ slides/ Slip/ Auto Hinges: Ebco/Hettich/ Hafele or equivalent approved make [ii] Adhesive: Fevicol/ Vamicol orequivalent approved make

Supplying and installation of pre-fabricated, factory made, overhead kitchen cabinet units, 600 mm height x 300 mm deep (Approx) as per the following specifications and as per Sketch No. 1 of GE Avadi:- [a] The frame work or carcass of the cabinets including its shutters, sides, bottom, shelves, etc. shall be made out of 16 to 18mm thick Marine plywood. All exposed surfaces and internal surfaces of the Cabinet units shall be provided with machine pressed lamination having thickness 1mm and 0.8mm respectively of approved shade and make and pasted with synthetic resin based adhesive. All the shutters shall be glazed with 5mm thick float glass fitted into marine plywood frame alround with necessary cleats, clips and magnetic catchers. Each Cabinet shall be provided with one glass shelf of 10 mm thick edge polished float Glass for horizontal partition in each cabinet.

[b] The dimensions of cabinets shall be designed to accommodate vertical storage spaces for smooth functioning of units. All shelves shall be supported on approved quality SS pins and shall be adjustable for various height requirements. The overhead cabinet carcass units shall be firmly fitted to the wall with PVC capped 2mm thick concealed MS hanging brackets each having width of 15mm and depth of 50mm. Each cabinet shall be supported on 2 brackets and these brackets shall be fixed on wall with necessary screws.

[c] Each shutter shall be fixed to the framework using two numbers of best quality Euro type Slip/ Auto Hinges and provided with one approved quality profile and brush finished Stainless Steel (SS) handle of grade 304 (minimum 150 mm long). [d] The thickness of four edge PVC lipping for shutters shall be 2mm Thick and the thickness of edge lipping of carcass/ plywood partition shall be 0.8mm and thickness of four edge lipping around the rebate of glass shutter shall be 0.6mm. The lipping/ banding shall match with the external laminate shade. All faces and edges of wooden planks and wooden fillers shall be painted with a coat of synthetic enamel primer and two coats of white colour synthetic enamel paint. [e] The wooden frame for shutter shall be made of minimum 70 mm wide marine plywood with lamination, wherever required. If there is a need of erecting additional vertical marine plywood members with laminate on account of site conditions, the quoted rate shall have provision of carrying out these works.

Notes: [i] All the modular kitchen cabinet works shall be carried out by the contractor through skilled tradesmen with standard Engineering practice and workmanship. [ii] Payment shall be made on the basis of front elevation area of modular units only. It is clarified that sides, top and bottom surfaces will not be measured for payment. [iii] The quoted rate shall include making of vertical partition with 16 to 18 mm thick marine plywood, if necessary, to accommodate vertical storage spaces as per the requirement [iv] All necessary hardware, wooden members for filling the gaps shall be included in the quoted rate.

Makes:- [i]Slip/ Auto Hinges: Ebco/Hettich/ Hafele or equivalent approved make [ii] Adhesive: Fevicol/ Vamicol orequivalent approved make

Supplying and installation of pre-fabricated, factory made, Loft with Semi box shutters of 750 mm height x 450 mm deep (Approx) as per the following specifications and as per Sketch No. 1 of GE Avadi:- [a] The frame work or carcass of the cabinets including its shutters, sides, bottom, shelves, etc. shall be made out of 16 to 18mm thick Marine plywood. All exposed surfaces and internal surfaces of the Cabinet units shall be provided with machine pressed lamination having thickness 1mm and 0.8mm respectively of approved shade and make and pasted with synthetic resin based adhesive. All the shutters shall be glazed with 5mm thick float glass fitted into marine plywood frame alround with necessary cleats, clips and magnetic catchers. Each Cabinet shall be provided with one glass shelf of 10 mm thick edge polished float Glass for horizontal partition in each cabinet.

[b] The dimensions of cabinets shall be designed to accommodate vertical storage spaces for smooth functioning of units. All shelves shall be supported on approved quality SS pins and shall be adjustable for various height requirements. The overhead cabinet carcass units shall be firmly fitted to the wall with PVC capped 2mm thick concealed MS hanging brackets each having width of 15mm and depth of 50mm. Each cabinet shall be supported on 2 brackets and these brackets shall be fixed on wall with necessary screws.

[c] Each shutter shall be fixed to the framework using two numbers of best quality Euro type Slip/ Auto Hinges and provided with one approved quality profile and brush finished Stainless Steel (SS) handle of grade 304 (minimum 150 mm long). [d] The thickness of four edge PVC lipping for shutters shall be 2mm Thick and the thickness of edge lipping of carcass/ plywood partition shall be 0.8mm and thickness of four edge lipping around the rebate of glass shutter shall be 0.6mm. The lipping/ banding shall match with the external laminate shade. All faces and edges of wooden planks and wooden fillers shall be painted with a coat of synthetic enamel primer and two coats of white colour synthetic enamel paint. [e] The wooden frame for shutter shall be made of minimum 70 mm wide marine plywood with lamination, wherever required. If there is a need of erecting additional vertical marine plywood members with laminate on account of site conditions, the quoted rate shall have provision of carrying out these works.

Notes: [i] All the modular kitchen cabinet works shall be carried out by the contractor through skilled tradesmen with standard Engineering practice and workmanship. [ii] Payment shall be made on the basis of front elevation area of modular units only. It is clarified that sides, top and bottom surfaces will not be measured for payment. [iii] The quoted rate shall include making of vertical partition with 16 to 18 mm thick marine plywood, if necessary, to accommodate vertical storage spaces as per the requirement [iv] All necessary hardware, wooden members for filling the gaps shall be included in the quoted rate.

Makes:- [i] Slip/ Auto Hinges: Ebco/Hettich/ Hafele or equivalent approved make [ii] Adhesive: Fevicol/ Vamicol orequivalent approved make

M&L for providing and fixing Dish Basket set of size 600mm x 560mm of SS - 304 grade with plain galvanized steel drawer (100mm height - 01 No), PVC Cutlery Tray and SS wire basket (100mm height - 01 No each) & Plate wire basket (150mm - 01 No) with required SS screws of suitable size complete all as per manufacturer's specification and as directed. Make : Ebco/Hettich/ Hafele or equivalent approved make

M&L for providing and fixing Bottle pull-out Basket set of size 300mm x 560mm x 500mm of SS - 304 grade with set of plain SS wire baskets (100mm height min - 02 Nos) with required SS screws of suitable size complete all as per manufacturer's specification and as directed. Make : Ebco/Hettich/ Hafele or equivalent approved make

M&L for providing and fixing Drawer Unit (02 Nos) of size 450mm x 560mm of galvanised steel SS - 304 grade with solid plain galvanized steel drawers (200mm height - 02 Nos) with required SS screws of suitable size complete all as per manufacturer's specification and as directed. Make : Ebco/Hettich/ Hafele or equivalent approved make

M&L for providing and fixing GTPT kit of size (900 x 300 x 50) mm of SS - 304 grade with PVC water collecting tray (01 No), SS wire basket (02 Nos) with required SS screws of suitable size complete all as per manufacturer's specification and as directed. Make : Ebco/Hettich/ Hafele or equivalent approved make

M&L for providing and fixing moveable Stainless steel (Grade 304) cylinder trolley under the cooktop/ Hob unit with back panel complete all as per manufacturer's specification and as directed. Make : Ebco/Hettich/ Hafele or equivalent approved make

M&L for providing and fixing Stainless steel (Grade 304) waste bin holder fixed on the Door shutter under the sink Unit complete all as per manufacturer's specification and as directed. Make : Ebco/Hettich/ Hafele or equivalent approved make

M&L for providing and fixing Skirting (REHAU) system-100mm brushed aluminium with hardware complete all as per manufacturer's specification and as directed. Make : Ebco/Hettich/ Hafele or equivalent approved make

S&F aluminium anodized tower bolt 100mm size complete all as specified and as directed.

S&F aluminium anodized tower bolt 200mm size complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed with screws complete all as specified and as directed.

S&F SS Butt hinges, medium weight, cold rolled mild steel of 100mm size fixed with screws complete all as specified and as directed.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised Type C21, 75mm size fixed with screws complete all as specified and as directed.

S&F aluminium handle, anodized, 150 mm size, cast type complete all as specified and as directed.

S&F aluminium handle, anodized, 200 mm size, cast type complete all as specified and as directed.

S&F in repairs for Harrison Curtain rails 20mm dia, mild steel, chromium plated with fixing brackets, stops, rollers, etc., in repair complete all as specified and as directed.

S&F in repairs tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F Powder coated aluminium frame for doors, windows, ventilators with one or more rebates (minimum thickness of powder coating 50 micron), with extruded built up standard / appropriate sections of approved make conforming to IS: 733 and IS:1285, including joining cleat for fixing, etc., (including channel for louver glass) including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. complete all as specified and as directed.

S&F Powder coated Aluminium window and ventilator shutters (minimum thickness of powder coating 50 micron), Glazed/ Gauzed Shutters without sash bar, side hung type with extruded built up standard / appropriate sections of approved make conforming to IS: 733 and IS:1285, aluminium section weighing 0.55 kg/m, including necessary jointing cleats, glazing clips, EPDM rubber/ neoprene gasket, snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (01) Nos hinges type B21 100 mm long 02 Nos suitable handle and fixing approved standard aluminium sections complete all as specified and as directed.

S&F Powder coated aluminium grill of approved design/ pattern, transparent or dyed to required shade according to relevant IS and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved powder coated aluminium standard section around the opening, complete all as specified and as directed.

M&L for 10mm thick Rendering in cement mortar (1:3) mixed with integral water proofing compound as per manufacturer's instructions on concrete surfaces of roof finished even and smooth without using extra cement and applying a uniform coat of hot blown bitumen of grade VG-10 @ 1.20 kg/ Sqm conforming to IS 702 over a coat of water based bituminous primer @ 0.40 ltr/ sqm including cleaning surfaces, water tightness testing, etc., and laying APP based polymeric membrane as per IS 16540-2017/ IS 16532-2017 weighing 3.6 kg/ sqm and minimum 3mm thick reinforced with polyester non woven fabric (weight not less than 150gms/ sqm) with overlap of 100mm minimum by forced application and finally finished the membrane surface by applying a coat of solar reflective aluminium paint @ 0.1 ltr/ Sqm complete all as per manufacturer's instructions all as specified and as directed. Note : Water proofing compound shall be measured and paid separately. Application of APP membrane shall be executed by the contractor through authorised applicator of manufacturer as approved by GE.

M&L for 15 mm Rendering in cement mortar (1:3) mixed with integral water proofing compound as per manufacturer's instructions, finished the surfaces even and smooth without using extra cement and applying evenly a coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm over a coat of bitumen primer @0.30 lit/sq.m including cleaning surfaces, testing for water tightness, etc. and provision of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) with overlap of 100mm minimum laid on primed surface by forced application as in sunken floor treatment complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately. Application of APP membrane shall be executed by the contractor through authorised applicator of manufacturer as approved by GE.

Taking down PVC pipes of any description and size incl all fittings, head shoes, bends swan necks etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

M&L for 75mm thick Plain Cement Concrete 1:2:4 type B1 using 20 mm graded stone aggregate, as in pavings, finished fair and even complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection finishing the exposed surfaces fair and even complete all as specified and as directed.

M&L for Bitumastic Gola 10mm wide x 75mm depth, with 80/25 bitumen and coarse sand mixture 1:3 by weight, at the junction of wall & plinth protection and at corners, etc. complete all as specified and as directed.

M&L 75mmm thick Plain Cement Concrete 1:4:8 Type D2 using 40 mm graded stone aggregate as in sub base for floor / hard standing etc., complete all as specified and as directed.

M&L for complete removal of existing water proofing treatment over roof including PCC of any thickness description in any position including cleaning the surfaces with wire brushing, watering and removing the debris exceeding 1Km but not exc 1.5 Km distance, etc., complete all as specified and as directed.

M&L for 25mm average thick Plain Cement Concrete 1:2:4 Type B-0 using 12.50 mm graded stone aggregate, mixed with integral water proofing compound as per manufacturers instructions, as in roof levelling course complete all as specified and as directed. Note : Water Proofing Compound shall be measured & paid separately.

M&L for 25mm thick Plain Cement Concrete 1:2:4 Type B0, using 12.5mm graded stone aggregate, as in floor, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Glazed ceramic tiles 7 to 8mm thick, 350 x 250 / 450 x 350mm size, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in vertical surfaces such as dado, skirting surfaces, laid over and including 10mm thick rendering in CM 1:4, etc., complete all as specified and as specified.

M&L for Non skid coloured ceramic tiles, 7 to 8mm thick (Square/ Rectangular) area of each tiles exc. 0.06 sqm but not exc. 0.11 sqm, in floors, etc., set and jointed in neat cement slurry and pointed in coloured cement to match including screed bed 15 mm thick in CM 1:4 as bedding layer for floor finishes complete all as specified and as directed.

M&L for Non skid matt superior finished, joint free, coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for Non skid matt superior finished, joint free, coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular), set and jointed in neat cement slurry and pointed in white or coloured cement to match, as in vertical surfaces such as dado, skirting surfaces, laid over and incl 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

M&L for Light shade double charged polished, Vitrified Ceramic tiles, 8 to 9mm thick (Square/ rectangular) area of each tile n.exc. 0.36 sqm, in floors, etc., set and jointed in neat cement slurry and pointed in whit or coloured cement to match over 15 mm thick screed bed in cm 1:4 complete all as specified and as directed.

M&L for Light shade double charged polished, Vitrified Ceramic tiles, 8 to 9mm thick (Square/ rectangular) polished, area of each tile n.exc. 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match, as in vertical surfaces such as dado, skirting surfaces, laid over and incl 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

M&L PCC chequered tiles 30cm x 30cm x 25mm thick with grey cement and pigments, as in floors, paths, etc. set and jointed in neat cement slurry and pointed in grey cement slurry with pigment laid over and including 20mm thick screed bed in CM 1:4 complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:3 on concrete ceiling surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:6 on brick / concrete surfaces, surfaces finished even and smooth without using extra cement up to any height complete all as specified and as directed.

M&L for 5mm thick cement plaster in CM 1:4 mixed with approved water proofing compound as per manufacturer's instructions over 10mm thick backing coat in CM 1:6 finished even and fair on brick/ concrete surfaces up to any height complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately

Taking down cement plaster on brick/ concrete surfaces (on walls/ ceilings) including racking out joints, hacking for key, scrubbing down with water, etc., complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick/ concrete surfaces and finished fair and even complete all as specified and as directed.

M&L for Preparation of newly plastered surfaces of walls and applying two coats of acrylic distemper over a coat of alkali resistant primer and chalk whiting complete all as specified and as directed.

M&L for complete removal of existing treatment and preparing of wall surfaces, applying two coats of acrylic distemper over a coat of alkali resistant primer including provision of 3mm thick wall care putty with smooth finish complete all as specified and as directed.

M&L for complete removal of existing treatment and preparing of wall surfaces, applying two coats of acrylic distemper over a coat of alkali resistant primer and chalk whiting complete all as specified and as directed.

M&L for complete removal of existing treatment and preparing wall surfaces, applying two coats of 100% Premium acrylic emulsion exterior weather coat paint of required shade (Company Depot Tinted) having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance, with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

M&L for complete removal of existing treatment and preparation of ceiling surfaces and applying two coats of white wash complete all as specified and as directed.

M&L for two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over on newly plastered surface of wall over a priming coat of exterior primer applied @ 0.90 litre/ 10sqm complete all as specified and as directed.

S&F 4mm thick figured glass, pin headed type and glazing with oil putty in squares not exc 0.5 sqm in each pane and glazing complete all as specified and as directed.

S&F 4mm thick sheet glass ordinary quality, in squares or rectangular shape of each pane not exc 0.5 sqm and glazing complete all as specified and directed.

M&L for preparation of new wood and wooden based surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer complete all as specified and as directed.

M&L for preparation of old painted wood and wooden based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for treating ends of new wooden posts, back of wooden chowkhats, etc., with tar or coal tar black paint, area tarred exc 0.1 sq.m but n.exc 0.5 sq.m each including necessary preparation of surfaces complete all as specified and as directed.

M&L for treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., with tar or coal tar black paint, area n exc 0.1 sq. m each including necessary Preparation of surfaces of wood and wood based materials, steel and iron work, new or old, complete all as specified and as directed.

Taking up or down 15mm bore steel water tubing and connections from any position and making good disturbed surfaces complete all as specified and as directed.

Taking up or down 20mm bore steel water tubing and connections from any position and making good disturbed surfaces complete all as specified and as directed.

Taking up or down 25mm bore steel water tubing and connections from any position and making good disturbed surfaces complete all as specified and as directed.

S&F Unplasticised PVC pipes and fittings of 20mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors, etc., complete all as specified and as directed.

S&F Unplasticised PVC pipes and fittings of 25mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors, etc., complete all as specified and as directed.

S&F Unplasticised PVC pipes and fittings of 40mm dia of pressure rating 10 kgf/cm2 fixed to walls, ceilings or laid in floors, etc., complete all as specified and as directed.

S&F 16mm outer dia CPVC pipes SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ ceiling or laid in floors complete all as specified and as directed.

S&F 1000 litres capacity triple layer, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including taking down old tank of any description and capacity complete all as specified and as directed.

S&F in repairs 15 mm bore Bib taps, brass chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for PVC/ iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repairs pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shanks and flynuts, screwed for union pipe and fixed to 15mm bore pipe complete all as specified and as directed.

S&F in repairs 15mm bore stop valve/Angle valve, chromium plated fancy type cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for PVC/iron pipes or for unions and fixed, complete and all as specified and as directed.

S&F Ball valves, high pressure, with of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 25 mm bore (Minimum weight 455 gms) and fixed complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm, complete all as specified and as directed.

S&F 75mm bore UPVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F 75 mm bore UPVC (SWR) pipes of single socketed in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F for UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, of 110mm dia complete all as specified and as directed.

S&F UPVC (SWR) bends 110mm dia of any radius with access door complete all as specified and as directed.

S&F 75mm bore. UPVC (SWR) bends complete all as specified and as directed.

S&F UPVC (SWR) branch piece, single (Y) equal or unequal 110mm bore with access door complete all as specified and as directed.

S&F UPVC (SWR) branch piece, double (Y) equal or unequal 110 mm bore with access door complete as specified and as directed.

S&F UPVC (SWR) vent cowl 110mm dia complete all as specified and as directed.

S&F 75mm outlet UPVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and as directed.

S&F UPVC (SWR) Gully trap 125/110mm size, setting and jointing with solvent cement complete all as specified and as directed.

S&F in repairs Vitreous china water closet pan (pedestal pattern), white including fixing bolts, plastic water closet seat, black/white closed pattern with flat bottom and cover and mild steel chromium plated hinging device including 10 litres capacity PVC flushing cistern (low level with inlet, ball valve float), brackets, flush pipe of polyethylene of low density PVC 32mm dia for low level cistern complete all as specified and as directed.

S&F in repairs Vitreous China wash Basin (flat back or angle back type), of size 550x400mm including brackets, PTMT waste coupling 32mm, including cutting for and pinning in ends of brackets or erecting stand, etc., complete all as specified and as directed.

S&F in repairs Soap dish vitreous china white of size 160x160x90mm fixed to wall complete all as specified and as directed.

S&F in repairs chromium plated shower roses 125mm dia with or without swivel joints any size, including fixing to steel pipe or union complete all as specified and as directed.

S&F in repairs stainless steel sinks with drainage board made of 1mm thick sheet for kitchen with plugs washer, waste pipes, cast iron cantilever brackets, connecting union to pipe over all size 915mm x 460mm with bowl size 410 x 330 x 160mm, including bedding in cement mortar to dwarf wall including fixing cantilever brackets and connecting unions to pipe complete all as specified and as directed.

S&F toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F brass CP two way bib tap of 15mm bore complete all as specified and as directed.

S & F health faucet, brass chromium plated, with 1.5m tube and wall hook fixed to 15mm bore GI / PVC pipe complete all as specified and as directed.

S&F toilet cabinet of size 350x450mm PVC body with shelf assembly, mirror mounted on shutter, etc., complete all as specified and as directed.

S&F brass CP wall mixer 2-in-1, for mixing of hot & cold water, screwed down for iron pipe of 15mm dia complete all as specified and as directed.

S&F Stainless steel plate rack of size 900X800X 250mm, made of 1mm thick stainless steel sheets of 304 grade, with necessary fittings and fixed to wall with screws, rawl plugs, etc complete all as specified and as directed.

S&F corner glass shelf, 300mm size, fixed to wall with bracket and screws complete all as specified and as directed. Make : Prayag CAT No BEA 56 or equivalent model in makes specified in Particular specifications.

S&F Stainless Steel Cockroach trap fixed into the existing floor trap at the location like toilet/ kitchen including cutting the existing grating making good the disturbed portion of any type flooring and cleaning the premises without disturbing the existing services complete all specified and as directed.

Forming contraction (Dummy) joint 65 mm deep x 10 mm wide filled with sealing compound grade "A" complete all specified and as directed.

Dismantling of Stone slab and tiles laid bedded and pointed in any mortar of any description or thickness in floors, apron, etc., complete all specified and as directed.

Demolition of cement concrete (un reinforced) in ground floor/ paving n.exc 15 cm below or above ground level complete all specified and as directed.

Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided complete all specified and as directed.

Demolition of un-reinforced cement concrete as in sunken floor of bath, wc and kitchen of any description and thickness complete all specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars, etc., complete all specified and as directed.

E/M ITEMS

INTERNAL ELECTRIC SUPPLY

Taking out carefully Copper/ Aluminium point wiring, light, fan, socket or power complete alongwith all fittings and fixtures such as switches, socket outlets, ceiling roses, holders, fan regulators, light fittings, etc., including making good the disturbed surface of wall/ floors complete all as specified and as directed.

Taking down existing unserviceable MCBs/MCCBs/ Distribution boards any capacity including making good the disturbed surfaces complete all as specified and as directed.

Taking down existing unserviceable Sub main wiring of any type/ size including making good the disturbed surfaces complete all as specified and as directed.

M&L for Point wiring complete with 1.5 sq mm single core PVC insulated FRLSH unsheathed cable 1100 volts grade with multi stranded copper conductor confirming to IS-694 1990 wih ISI marked (for phase, neutral and earth) in and including non-metalic rigid PVC conduit medium grade with ISI Mark of minimum 20mm dia and all conduit accessories concealed in wall/ ceiling or fixed to roof/ truss/ columns, etc. including cutting/chases in wall/ ceiling including factory made branded make embossed galvanised steel pressed terminal boxes alongwith suitable size modular cover plates with frames for fixing modular switches and sockets, fan regulators, etc., of suitable size modules and the earth wire to be connected to common earth dolly complete all as specified and as directed for the following :- Note: (i) Location of light points, 6 Amp socket points and light fittings shall be as directed by Engr-in-charge as per site/ user requirement. (ii) The cost of necessary cutting chases for required width and depth for concealed conduit incl making good disturbed surface to match the existing adjoining surfaces shall deemed to be included in the quoted rate by the contractor.

One light point controlled by one modular switch 6A one way.

One Ceiling/Exhaust/Wall fan point controlled by one modular switch 6A.

One 3 pin 6 Amps socket outlet point controlled by one 6A switch on independent board.

One 3 pin 6 Amps socket outlet point controlled by one 6A switch on the same board with other switches

One bell point controlled by one bell push.

One light point controlled by two nos, 2-way, 6 Amps switch.

M&L for Point wiring complete all a specified with 1100 Volts grade 4 sq mm single core PVC insulated FRLSH cable 1100 volts grade with multi stranded copper conductor conforming to IS 694 1990 with ISI marked (for phase, neutral and earth)in and including non-metallic rigid PVC conduit medium grade ISI Mark of minimum size 20mm dia all accessories concealed including cutting/ chases in wall/ceiling/fixed to roof/truss/columns etc and including factory made branded make embossed galvanised steel pressed terminal boxes for fixing modular sockets of suitable size modules and the earth wire to be connected to common earth dolly all as specified and as directed for One three pin modular switch socket 16 amps outlet on independent board.

S&F modular switch 1way 6A, 1 module 230 volts complete all as specified and as directed.

S&F Modular switch 2 way 6A, 1 module 230 volts complete all as specified and as directed.

S&F modular switch 1way 16A, 1 module 230 volts complete all as specified and as directed.

S&F modular Bell push 6A, 1 module, 230 volts complete all as specified and as directed.

S&F Modular Type shuttered Socket outlet, 3 pin 6 Amps, 230 volts two modules with ISI mark complete all as specified and as directed.

S&F Modular Type shuttered Socket outlet, 3 pin 6/16 Amps, 230 volts Two modules with ISI mark complete all as specified and as directed.

S&F Electronic type fan regulator stepped socket type, 230 volts complete all as specified and as directed.

S&F Electric Bell Ding-dong 230 volts AC single pole complete all as specified and as directed.

S&F Electric Bell/ Buzzer, AC, 230 volts, single pole complete all as specified and as directed.

S&F ceiling rose three terminal surface Bakelite type AC 50 Hz 230 volts of size 65 x 50 mm complete all as specified and as directed.

S&F lamp holder suitable for B-22 base lamps insulated body surface Bakelite with back plate suitable for angle/ batten fittings completed all as specified and as directed

S&F LED Bulbs 12 Watts suitable for B-22 base holders complete all as specified and as directed.

S&F LED batten type light fitting, 1x 20W, 4 feet long, 230V, with extruded aluminium housing, integrated electronic driver, holder, 20 W LED tube and connecting up with PVC sheathed 1.5sqmm x 3 core flexible copper conductor cable from ceiling rose to fitting complete all as specified and as directed.

Fixing only serviceable light fittings obtained from taking down in new or old location including connecting up with new three core flexible copper conductor cable of suitable size from ceiling rose to connector of light fitting complete all as specified and as directed. Note: Serviceable light fittings obtained from item No. 124 of this BoQ shall be fixed under this item.

S&F LED batten type light fitting, 1x 10W, 2 feet long, 230V, with extruded aluminium housing, integrated electronic driver, holder, 10 W LED tube and connecting up with PVC sheathed 1.5sqmm x 3 core flexible copper conductor cable from ceiling rose to fitting complete all as specified and as directed.

S&F LED light fitting 1x10W Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection all as specified and as directed.

S&F Decorative LED wall light fitting, made out of polycarbonate suitable for and including B-22 base LED Bulb, 10 Watt fixed on wall and making electric connection complete all as specified and as directed.

S&F LED Reading lamp 05 Watt suitable for single phase AC supply, fixed on wall with the help of screws complete all as specified and as directed.

Supply and Fix TV CO-Axial socket outlet modular type complete all as specified and as directed.

M&L for non metallic rigid PVC conduit and conduit accessories 20mm dia, medium grade concealed in wall/ ceiling for TV/ Telephone cable all as directed.

S&F MCB SP 6 to 32 Amps 240 volts B- type complete all as specified and as directed

S&F MCB SPN 16 Amps 240 volts B- type complete all as specified and as directed

S&F RCBO double pole 30mA, capacity 40 Amps 240 volts complete all as specified and as directed.

S&F RCBO Four pole 30mA, capacity 63 Amps 240 volts complete all as specified and as directed.

S&F sheet metal enclosure MCB DB SPN 12 way, 240 volts double door with locking system complete all as specified and as directed.

S&F sheet metal enclosure MCB DB SPN 4 way, 240 volts double door with locking system complete all as specified and as directed.

S&F TPN DB 4 way double door with provision of RCBO as incoming 4P 63A and SP MCB out goings made out of CRCA sheet housing duly powder coated complete all as specified and as directed.

S&F TPN vertical DB 4 way double door with provision and including MCCB as incoming 4P 100A 16 KA and SP MCB out goings made out of CRCA sheet housing duly powder coated complete all as specified and as directed.

S&F in repairs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole MCB 20 Amps complete all as specified and as directed.

M&L Submain wiring with 2 runs of single core 6 sqmm PVC insulated FRLSH multistranded 1100 volts grade wire, copper conductor drawn through and including non-metalic, medium grade, rigid PVC conduit and conduit accessories of suitable size with ISI Mark and all conduit accessories, concealed in walls/ ceilings or fixed to roof/ truss/ columns, etc., including necessary cutting/chases in wall/ ceiling including one run of single core 6 sqmm PVC insulated sheathed multistranded 1100 volts grade with copper conductor cable as earth continuity conductor along with the wiring and connected from DB to DB/main board complete all as specified and as directed. Note: 3 runs of 6 sqmm copper conductor cables and one run of PVC conduit shall be measured as one length. The rate quoted shall be deamed to include making good disturbed portion to match with adjoining surfaces.

M&L Submain wiring with 4 runs of single core 10 sqmm PVC insulated FRLSH multistranded 1100 volts grade wire, copper conductor drawn through and including non-metalic, medium grade, rigid PVC conduit and conduit accessories of suitable size with ISI Mark and all conduit accessories, concealed in walls/ ceilings or fixed to roof/ truss/ columns, etc., including necessary cutting/chases in wall/ ceiling including one run of single core 10 sqmm PVC insulated sheathed multistranded 1100 volts grade with copper conductor cable as earth continuity conductor along with the wiring and connected from DB to DB/main board complete all as specified and as directed. Note: 5 runs of 10 sqmm copper conductor cables and one run of PVC conduit shall be measured as one length. The rate quoted shall be deamed to include making good disturbed portion to match with adjoining surfaces.

M&L Submain wiring with 2 runs of single core 4 sqmm PVC insulated FRLSH multistranded 1100 volts grade wire, copper conductor drawn through and including non-metalic, medium grade, rigid PVC conduit and conduit accessories of suitable size with ISI Mark and all conduit accessories, concealed in walls/ ceilings or fixed to roof/ truss/ columns, etc., including necessary cutting/chases in wall/ ceilingincluding one run of single core 4 sqmm PVC insulated sheathed multistranded 1100 volts grade with copper conductor cable as earth continuity conductor along with the wiring and connected from DB to DB/main board complete all as specified and as directed. Note: 3 runs of 4 sqmm copper conductor cables and one run of PVC conduit shall be measured as one length. The rate quoted shall be deamed to include making good disturbed portion to match with adjoining surfaces.

M&L Submain wiring with 2 runs of single core 1.5 sqmm PVC insulated FRLSH multistranded 1100 volts grade wire, copper conductor drawn through and including non-metalic, medium grade, rigid PVC conduit and conduit accessories of suitable size with ISI Mark and all conduit accessories, concealed in walls/ ceilings or fixed to roof/ truss/ columns, etc., including necessary cutting/chases in wall/ ceilingincluding one run of single core 1.5 sqmm PVC insulated sheathed multistranded 1100 volts grade with copper conductor cable as earth continuity conductor along with the wiring and connected from DB to DB/main board complete all as specified and as directed. Note: 3 runs of 1.5 sqmm copper conductor cables and one run of PVC conduit shall be measured as one length. The rate quoted shall be deamed to include making good disturbed portion to match with adjoining surfaces.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm X 60cm X 6mm thick buried in ground vertically to a depth not less than 2.25 metre below normal ground level, normal with top edge of earth plate not less than 1.5 metre below normal ground level, earth plate connected to a galvanized earth lead wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part-I (2009) connected to earth test point all as specified or indicated including testing on completion with and including 15 mm bore light grade GI protection pipe 7.5 meters long for earth including PCC 1:2:4 pit with pre cast RCC 1:2:4 type B1 cover 40 mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hook made out of 6mm dia MS bars watering arrangement with funnel wire, common salt and charcoal filling, necessary excavation and earth work in any type of soil including taking down existing earthing of any description complete all as specified and as directed.

Taking down ceiling fan/ exhaust fan of any description and size complete and removing to store complete all as specified and as directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200 mm sweep. Min air delivery 210 CFM BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

S&F exhaust fan, steel body AC single Phase, 230V of size 300mm sweep with, blades, and frame and louvers including cutting the wall of suitable size for mounting and plastering the disturbed surfaces complete all as specified and as directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm including cutting the wall of suitable size and plastering the disturbed surfaces complete all as specified and as directed.

HOT WATER SUPPLY

S&F electric water heater, storage type steel body with enamel coating in both storage (inner) tank and heating element of 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat for adjustable temperature setting, NRV, connection piece hold fast 10 cm long and washers complete all as specified and as directed.

Disconnecting the power supply, dismantling the inlet and outlet connections and taking down existing serviceable electric heaters from any position and transporting to store for safe custody and reuse complete all as specified and as directed.

M&L for Re-fixing the serviceable electric heaters at the location where dismantled and connecting the inlet and outlet connections testing complete all as specified and as directed.

ELECTRICAL CHIMNEY

Supply, erection & testing of electrical chimney with the following specifications :- (a) Size : 750mm (Min) (b) Shape/ Mounting : Box/ Wall mounting (c) Suction capacity : 1200m³/hr (d) Air outlet size : 150mm (e) Duct size : 150mm (f) Duct : MOC-Stainless Steel (g) Duct pipe/ baffle filter : inclusive as required (h) Motor type : BLDC motor, 240W (j) Blower type : Metallic (k) Lamp : 2 x 1.5W (l) Finish : Stainless Steel (m) Features : Low Noise (less than 62dB) steam auto clean (n) Controls : Multi speed option, motion sensor Make : Faber/ Hindware/ Glen/ Kaff/ Crompton

EXTERNAL ELECTRIC SUPPLY

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, laying of cable/pipes etc., and n.exc 1.5 m in depth and getting out Soft/ Loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in Soft/ loose soil complete all as specified and as directed.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5m above the starting point complete all as specified and as directed.

M&L for riddled earth (by sieving the excavated sand) filled before and after laying of cable, punned down, as in protection of cables, complete all as specified and as directed. Note: Punned depth will be measured and paid

Supplying and laying well burnt sub class B bricks as mechanical protection to underground cables in the trenches complete all as specified and as directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with strandard aluminium conductor of size 50 sqmm x 3.5 core complete all as specified and as directed.

Supply, Laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with strandard aluminium conductor of size 35 sqmm x 3.5 core complete all as specified and as directed.

S&F in MCCB 4 pole in existing LT Panel board, 100 Amps, 16 KA, 415V, AC, fixed type including necessary connections complete all as specified and as directed.

P S G CONSTRUCTIONS (BID ID -3275798)

Atish Builders LLP (BID ID -3282209)

Lucky Enterprises (BID ID -3278460)

Sai Ram Builders (BID ID -3278461)

K. VENKATESH NAIDU (BID ID -3278339)