PROVN OF SINGLE LIVING 02 X ORs ACCN FOR HQ CWE (A) JODHPUR AND ADDN / ALTN OF SAMPLE ROOM OF BLDG NO. 452 IN ARMY AREA JODHPUR UNDER GE (ARMY) NO. 01 JODHPUR

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil complete all as specified and as directed.

All as per Sl. Item No. 1.00 here-in-above, but in soft/loose soil.

M&L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and as directed.

M&L for Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M & L for Cement concrete in foundations, filling and mass concrete 1:4:8 D2 (40mm graded aggregate) foundation, wall complete all as specified and as directed.

M&L for ATT treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L for ATT treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M&L for ATT treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

Use & waste of Formwork to sides of reinforced concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter of flate and fair finish surface complete all as specified and as directed.

M &L for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete RCC (design mix) M -25 (20mm graded aggregate) complete all as specified and as directed.

Use & waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions of rectangular fair finish surface complete all as specified and as directed.

M &L for RCC (design mix) M-25 in Columns, pillars, piers, posts and struts complete all as specified and as directed.

Use & waste of Formwork to sides and soffits of floor beam, lintel beam, roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, for rough finished surface of concrete etc complete all as specified and as directed.

M&L for RCC (design mix) M 25 of Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finish flat surface of concrete complete all as specified and as directed.

Use & waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide (120mm thick of roof slab) complete all as specified and as directed.

M&L for RCC (design mix) M-25 for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and as directed.

M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for column,beams, Roof complete all as specified and as directed.

S & F mild steel TMT bar 6 to 10 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed

M & L for Mild steel TMT bars 5mm dia and over upto andincluding 10mm dia in stirrups, spacers and binders to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Supply and fabrication of Mild steel soft drawn binding or tying wire 1 mm dia, annealed complete all as specified and as directed.

M&L for squarred rubble walling Jodhpur type regular coursed well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and as directed.

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified and directed.

M &L for Brickwork with fly ash old size burnt bricks, straight or curved on plan exc 6m mean radius, built in and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) in foundation, above plinth level upto two stories in all shapes and sizes all as specified and as directed by Engr-in-charge.

M&L for Rendering 15 mm thick on stone masonry surface or other than fair faces of brick wall surface in CM 1:6 finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for Rendering 10 mm thick on stone masonry surface or other than fair faces of brick wall surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 10 mm thick on stone masonry surface or other than fair faces of brick wall surface in CM 1:4 finished even and smooth without using extra cement but mixed with water proofing compund complete all as specified and directed.

M&L for 10mm thick rendering in CM (1:4) on fair faces of brick work or concrete surface on wall finished even & smooth without using extra cement complete all as specified & directed by Engr-in-Charge.

M&L for Rendering 5mm thick on fair faces of cilling of CM 1:4 to be finished even and smooth (without using extra cement) complete all as specified & directed.

M&L for Keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 complete all as specified.

M&L for preparation of newly plastered surfaces of wall and applying 2 coats of wall care putty on wall surfaces including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper paint over a coat of primer on wall complete all as specified and directed.

All as per item No.31.00 here-in-above but as on celing sufaces.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash over 2 coats of wall care putty on wall surfaces complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash over 2 coats of wall core putty on ceiling surfaces complete all as specified and as directed.

M&L for preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over a coat of white wash, complete all as specified and as directed.

Earth filling under floor, including spreading, leveling, watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and as directed by engr-in-charge

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering 100mm thick

M & L for Hardcore of gauge n exc. 63 mm, broken stone and boulders to deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by engr-in-charge.

M&L for cement concrete type C-2,1:3:6 (40mm graded aggregate) as sub base of flooring of 100 mm thick complete all as specified and as directed by Engr-in-Charge.

M&L for cement concrete type D-2,1:4:8 (40mm graded aggregate) as sub base of flooring of 100 mm thick complete all as specified and as directed by Engr-in-Charge.

M&L for 25 mm thick cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L for vitrified tiles of dark shade, 10mm thick (minimum) (square/ rectangular) polished area of each tiles equal to or not exceeding 0.36 Sqm (size & shape, shade and pattern as approved by GE), as in flooring, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 15 mm thick screed bed in CM 1:6, complete all as specified and as directed. Note :- Colour & pattern of tile shall be approved by GE.

All as per Sl. Item No. 42.00 here-in-above, but as in dado/skirting over and including 10 mm thick plaster in CM 1:4

M&L of 18-20mm thick machine cut KOTA stone slab as in floor (size not less than 580mm x 580mm) , treads, steps etc(Single piece for steps), machine cut, laid over cement and jointed with grey cement slurry with pigment to match the shade of the slab, incl rubbing and Mirror polishing all as specified as in floors over and including 15mm thick in screed bed in CM (1:6) complete all as specified and as directed by Engr-in-charge.

M&L of 18-20mm thick machine cut KOTA stone slab riser of step , skirting, dado etc(Single piece for steps), machine cut, laid over cement and jointed with grey cement slurry with pigment to match the shade of the slab, incl rubbing and Mirror polishing all as specified including backing coat of 10mm thick in CM (1:4) complete all as specified and as directed by Engr-in-charge.

M&L for glazed colour ceramic tiles (premium quality) of size 250X450X6-7mm / 300X450X6-7 mm, as in vertical surface such as dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 15mm thick backing coat in CM (1:6) complete all as specified and directed.

M&L for non skid ceramic coloured tiles (premium quality) of size 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for 15-18mm thick Udaipur green marble machine cut on cill, shelves, platform laid over 10mm thick screed bed in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including polishing and rounding the edges complete all as specified and as directed by Engr -in-charge.

M & L for 18-20 mm thick Black granite stone as in cooking platform, counter slab, slabs for oval type WHB,sinks etc & the likes complete laid over 15 mm thick cement sand screed in CM 1:4 incl mirror polishing complete including pointingin white cement (1:2) using marble dust with admixture of pigment to match with shade of granite& providing necessary holes for gas pipe / water supply pipes etc complete all as specified and as directed.

M&L of 20-25mm thick machine cut KOTA stone slab as in shelves (Single piece) machine cut, laid over cement mortar 1:4 on self, cub board, almira,partation etc and jointed with grey cement slurry with pigment to match the shade of the slab, incl rubbing and Mirror polishing complete all as specified and as directed by Engr -in-charge.

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete all as specified and as directed by Engr -in-charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M & L for pressed steel door frames (105X60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates, PCC etc, complete all as specified and as directed by Engr -in-charge.

M & L for pressed steel door frames (165X60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates, PCC etc, complete all as specified and as directed by Engr -in-charge.

S&F factory made box type windows (steel) (BWM) with side hung shutter with cooler opening as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete with glazing bars, dovetailed or welded complete all as specified and as directed by Engr -in-charge. Note.:Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same. (ii) Glass panes, wire cloth and grill shall be measured and paid seperately

S&F factory made box type windows (steel) (BWM) with side hung shutter with cooler opening as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete without glazing bars, dovetailed or welded complete all as specified and as directed by Engr -in-charge. Note.:Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same. (ii) Glass panes, wire cloth and grill shall be measured and paid seperately

S&F factory made box type windows (steel) (BWM) with side hung shutter without cooler opening as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete with glazing bars, dovetailed or welded complete all as specified and as directed by Engr -in-charge. Note.:Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same. (ii) Glass panes, wire cloth and grill shall be measured and paid seperately

S&F factory made box type windows (steel) (BWM) with side hung shutter without cooler opening as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete without glazing bars, dovetailed or welded complete all as specified and as directed by Engr -in-charge. Note.:Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same. (ii) Glass panes, wire cloth and grill shall be measured and paid seperately

S&F of Box type steel ventilator with top hung shutter including hinges with steel handle, and steel peg stay, complete with glazing bars, complete all as specified and as directed by Engr -in-charge.

All as per Sl. Item No. 58.00 here-in-above, but without glazing bar.

Supply and fabrication of Mild steel guard bars, grills, grating, and similar work and welded to window frames, door frames (made up of angle), balcony railing confirming to FE 290, gde E-165 etc complete all as specified and as directed by Engr -in-charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm complete all as specified and as directed by Engr -in-charge.

S&F of stainless steel wire cloth 0.36 mm nominal dia of wire & avg width of appertuer 1.40 mm fixed to Anodised aliminium framework of windows / vents & door shutters etc complete all as specified and as directed by Engr -in-charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified and as directed.

M&L for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides if one face is covered with decorative face veneer (sanmica) with lipping/frame to match and complete all as specified and as directed by Engr -in-charge.

S & F 35mm thick factory made second class hardwood glazed and Skelton door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009section 8 clause 8.24 (a) and complete all as specified and as directed by Engr -in-charge.

S &F of Stainless steel butt hinges medium weight, cold rolled of size 100 mm size complete all as specified and as directed by Engr -in-charge.

S&F 150 mm double action spring hinge, brass with phosphor bronze wire spring bright polished complete all as specified and as directed by Engr -in-charge.

S&F 200mm long aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and as directed by Engr -in-charge.

S&F 150mm long alluminium alloy handles, cast type, anodized and fixed complete all as specified and as directed by Engr -in-charge.

S&F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 12mm dia and 300mm long complete all as specified and as directed by Engr -in-charge.

S&F in repairs 50 mm size best quality double door stopper of aluminium alloy body and tongue, anodised & hard rubber shoe all as per sample complete all as specified and as directed by Engr -in-charge.

S&F for 3 mm thick plain sheet glass ordinary quality & glazing with oil putty in square n exc 0.50Sqm in each pane complete all as specified and as directed by Engr -in-charge.

S&F for 4 mm thick figurred , pin headed glass ordinary quality & glazing with oil putty in square n exc 0.50Sqm in each pane complete all as specified and as directed by Engr -in-charge.

S&F decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end (As approved by Engr -in-charge).

S&F SS peg set of five fixing with wall complete all as specified and as directed by Engr -in-charge.

M &L of fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete. ( Taking down of existing Cupboard /Almirah included in the rates)

S & F in repair Mortice lock 2 levers vertical type mild steel body size 75 mm with a set of 2 keys complete fixed as in repairs to Steel Built in Cupboards all as specified & directed at site

M&L preparation of new or previously untreated steel surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L a coat of pink primer complete all as specified and directed.

M&L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in coping, etc, including necessary form work all as specified & directed.

S&F in replacement of Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)and cast iron `P' or `S' trap front or back fixed in repairs Including connection to trap etc and provision of cement concrete bedding and making good to floor complete all as specified and directed.

S&F PVC low level 10 lit capacity valve less syphonic action type flushing cistern with inlet ball valve and handle including brackets complete all as specified and directed

Supply, laying, testing & commissioning of 20 mm outer dia CPVC pipe,SDR-11, with all fitting (eblow, socket,tee with internal thread of brass) fixed to wall, ceiling or laid on floor, with CPVC solvent, complete all as specified and as directed by Engr-in-Charge.

Supply, laying, testing & commissioning of 25 mm outer dia CPVC pipe,SDR-11, with all fitting (eblow, socket,tee with internal thread of brass) fixed to wall, ceiling or laid on floor, with CPVC solvent, complete all as specified and as directed by Engr-in-Charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth

S&F PVC connections of 15mm size with PTMT nuts of 600mm long complete all as specified and directed.

S&F PVC connections of 15mm size with PTMT nuts of 450mm long complete all as specified and directed.

S&F in repair of vetrious china wash basin white flat back 550x400mm including brackets, vitreous china padastal, 32mm bore CP coupling etc., complete all as specified and directed.

S&F Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar1:2, securing urinal to plugs with and including 60mm long brassscrews, pointing around urinal back in cement, complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete all as specified and directed.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F of flush pipe of polythylene of low or high density or PVC 32mm dia for WHB, complete all as specified and directed.

S&F in repair bib taps chromium plated 15mm cast copper alloy, fancy type screwed down screwed for iron pipe 15mm bore complete all as specified and directed

S&F in repair stop valves, 15mm cast copper alloy, screwed both ends for iron pipe 15mm dia, fixed complete all as specified and directed

S&F Two way angle cock cromium plated fancy type 15 mm bore /size, complete all as specified and directed.

S&F in repair CP fancy type, health faucet with 1000mm long flexible mild steel tube with wall hook complete all as specified and directed.

S & F in repair 15mm bore stop valves/Angle valve, cast copper alloy, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repair of Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms)complete all as specified and directed.

S&F in repair of Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms complete all as specified and directed.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms)

S&F Toilet paper holder, vitreous China, box type coloured, complete all as specified and directed.

S&F tubular towel rail 20mm dia brass chromium plated `D' type 60cm long with bracket and fixed complete all as directed.

Supplying and laying of 75 mm dia UPVC pipes SWR & Plain UPVC SDR 11 fittings in trenches complete all as specified.(with all fitting), complete all as specified and directed.

Supplying and laying of 110 mm dia UPVC pipes SWR & Plain UPVC SDR 11 fittings in trenches complete all as specified. (with all fitting), complete all as specified and directed.

M&L for 75mm outlet diameter UPVC nahani trap, with CP Mild steel grating (with or without hole) including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate, complete all as specified and directed.

M&L for 110 mm outlet diameter UPVC nahani trap, with CP Mild steel grating (with or without hole) including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate, complete all as specified and directed.

M&L for 150mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregates as in platform for water tank on roof, finished the surface even and smooth with WPC complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including one 20mm ball brass valve with polythene float and fly nut complete all as specified and directed.

Supply & laying jointing and testing 150mm bore reinforced cement concrete pipes class NP-2 laid and jointed in cement mortor 1:1 complete, with collars or socket/spigot type laid jointed and haunching at side in cement, complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate bed to drain pipe 150 mm dia including packing under and hunching against the pipe after they are laid including necessary formwork all as specified.

M&L for cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate bed to drain pipe 150 mm dia including packing under and hunching against the pipe after they are laid including necessary formwork all as specified.

M&L for neat cement slurry @ 3.00 kg/Sqm and screeding / bedding layer of 10 mm thick in CM 1:3 mixed with water proofing compound as per manufacturer instructions over the RCC roof slab for laying of water proofing treatment including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastered surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm using torch application method with minimum 10cm side lap and 15cm end lap complete . (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen conforming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : 40 mm thick plain cement concrete 1:2:4 (using 20 mm stone crushed aggregate) as in roof padding, including WPC as per manufacturer instruction. NOTE :- 1. A Information Tablet will be put up in the front side wall of the buildings where this work will be done. All building/structure shall be provided with plaque (tablet) furnishing the information as per PS clause, in plaster engraving in and painted as directed by GE 2.WPC shall be measured and paid separately under respective item.

Supply only integral water proofing compound (ISI marked), complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 (using 12.50mm graded stone agg) over roof for making good depression/undulation and as in roof kerb to match the existing, complete all as specified and directed.

M&L for laying 40-50 mm thick Machine cut sand stone slabs as in Plinth protections laid over 20 mm thick cement sand screed in CM1:4 over 50 mm thick PCC 1:2:4 type B-1 all as specified and directed including filling the joints of sand stone slabs with neat cement mixed with pigment to match the shade of slab, complete all as specified and directed.

M&L for mild steel work in Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for 75 mm thick, PCC 1:4:8 type D2 by using 40mm graded crushed stone aggregate as in sub base of floor complete all as specified and as directed.

Supply and laying factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for machine pressed precast cement concrete coloured rubberised interlocking paver block any shape & size of 60mm thick M-35, grade with 6mm top layer of anti abrasive material conforming to IS 15658-2006 over & including 25mm thick sand cushioning complete all as specified and directed.

M&L for rolled mild steel frame work in trusses purlins, posts etc complete using MS angle iron, MS Hollow Square or rectangular sections,flat irons etc complete incl necessary welding cutting to shape & hoisted & fixed in position complete all as directed & specified .

M&L for rolled mild steel frame work in trusses purlins, posts etc complete using MS angle iron, MS Hollow Square or rectangular sections,flat irons etc complete incl necessary welding cutting to shape & hoisted & fixed in position, including dismantling cast iron work of any description complete all as directed & specified .

M&L for pre painted galvalume aluminium zinc GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering fixed with J or L hooks , including dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc, complete all as directed.

M&L for pre painted galvalume aluminium zinc GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering fixed with J or L hooks of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc, complete all as directed.

M & L Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges 1.25 mm thick 150mm dia sheet

Excavating in post holes (of similar holes) each n. Exc. 0.50 Cum getting out, any type of soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc. 50m and making good surface complete all as specified and directed.

M & L for PCC (1:3:6) type C2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for precast cement concrete block masonry 1:2:4 type B-1 (20mm graded stone aggregate) with solid blocks exc. 10cm thick in width setting in 1:4 cement mortar, complete, in walls all as directed.

M&L for preparation of newly surfaces of wall even and applying Two coats of 100% Premium acrylic emulsion paint weather proof (plastic paint) and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm complete all as specified & directed by Engr-in-Charge.

Surface excavtion n exc 30cm deep and avg 15cm deep and getting out soft/ loose soil complete all as specified and directed.

S&F Anodised aluminium frame powder coated for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium door ,window shutters including powder coating of any colour (Thickness of powder coating not less than 50 micron) , aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed.

Pre powder coated aluminium decogrill all as per sample fixed to aluminium framework of windows & ventilators complete all as specified and directed.

S & F of anodised aluminium snap grid frame work ( 605 x 605 mm) for false ceiling and including dismantling of old u/s existing false ceiling, etc complete all as specified and directed.

S & F of anodised aluminium snap grid frame work ( 605 x 605 mm) for false ceiling, etc complete all as specified and directed.

M&L for Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instruction, complete all as specified and directed.

M&L 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate).

M&L for 18 mm thick Prelaminated particle board for cupboard shutter etc, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised with 30mm width of flap when open complete all as specified and directed.

S&F of 100 mm long Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws

S&F 100mm size MS butt hinges medium weight (ISI Marked), cold rolled mild steel complete.

S & F and in repair for 100mm long, mild steel single action spring hinge all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in surface channel or benching and drains including finishing the top of benching even and smooth using extra cement (Forming fair finished channel shall be measured separately), complete all as specified and as directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built old size brick in CM 1:4, complete all as specified and as directed.

M&L PCC (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in coping including necessary formwork, complete all as specified and as directed .

M&L for providing precast RCC 1:2:4 type B-1 using 20mm graded aggregate as in cover slab for man hloes set in CM 1:6, complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting 150mm dia new drain pipe/NP2 pipe and making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4th Section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and directed.

S&F 25mm bore water GI tubing medium grade, galvanized, with all fittings laid in trenches, complete all as specified and as directed.

S&F in replacement 25 mm bore brass, gate valve, as per sample, screwed both ends for iron pipe, complete complete all as specified and directed.

S&F in replacement 20 mm bore gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe, complete complete all as specified and directed.

M&L for drilling & tapping to 20/25mm bore GI tubing for branch connections of the 20/25mm bore GI tubing necessary welding, clamps, rubber gasket etc complete all as specified & directed by Engineer-in-charge.

M&L for cutting existing steel tubing for alterations or additions (each but measured) for 40mm bore pipe and inserting Tee equal including necessary earth work complete all as specified and as directed.

M&L for Cutting of existing road 0.25 mtrs wide and 0.60 mtrs depth, 3.50 mtrs length for laying of GI pipe/cables and repair / making good with by using cement concrete (1:4:8) type D-2 using 40 mm graded crushed stone aggregate/ tar to match with the existing surface/ spot as directed by Engineer-in-charge.

M & L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces ) conduit of size 20 mm or med grade as required as site, totally concealed in walls incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end suitable for One light/fan/bell point controlled by one, one way switch, all as specified, directed . Note:- The rates of chase cutting on wall done concealed conduit and steel terminal boxes are included in the unit rates all as specified and directed by Engr-in-Charge.

All as per item No. 155.00 here-in-above, but one socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per item No. 155.00 here-in-above, but one socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per item No. 155.00 here-in-above, but with 2.5 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for indpendent 16 Amp point.

S&F Switch piano type, single pole, one way, 6 amps, 230 volts, ISI Marked, complete all as specified and directed.

S&F Socket, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, ISI Marked, complete all as specified and directed.

S&F Switch piano type, single pole, one way, 16 amps, 230 volts, ISI Marked, complete all as specified and directed.

S&F Socket, 6 pin, 6/16 Amp, multipurpose shutter type, 230 volts, ISI Marked, complete all as specified and directed.

Supplying fixing and replacement of PVC angle Lamp holder, bakelite body including LED Bulb 9W, 230 volts, ISI Marked complete all as specified and directed.

Supplying and fixing of Ceiling rose, three terminals, bakelite body, 230 volts, ISI Marked complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fixing LED lights fitting 1x 18/20W, 220V, AC decorative box type with driver, holder including AC decorative box type with driver, holder including,copper conductor cable of suitable size from ceiling rose complete complete, 4 ft long all as specified and directed.

S&F bldg security LED Light Luminaire of 25 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable complete all as directed.

M&L for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note:- Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces. .

M&L for sub main wiring with 2 run of 4 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note:- Two run of 4 Sq.mm. and one run of 4 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces. .

S&F MCB, B Curve type, 10 kA, 40/43Amp, SPN with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed.

Supply and fixing as MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB all as specified and directed by the Engr-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 x 60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, nnected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 5 connected to Earthing test point all as ecified or indicated including testing on completion( Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover & GI 15 mm dia protection pipe upto 7.5 mtr. lead etc. complete )

S&F socketed stepped type electonic fan regulator flush type , ISI Marked, complete all as specified and directed.

Supply & Fixing connecting, and commissioning of street light fitting 30/45 watt LED , IP-65/66 protection, single peice pressure dia cast aluminium alloy housing high grade powder coated finish with heat resistant toughned clear glass cover for lamp and contror gear compartment with high voltage surge protection device upto 4.5 KV, Prewired including 1.60 mtr long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable complete all as specified.

S&F 15mm bore medium grade GI pipe fixed to wall, ceiling or laid in trenches.

Supply,testing and installation in replacement electric storage geyser of capacity 25 Ltrs, BEE 5 star rating, 230Volts, AC, 50Hz, comprising of heating element 2000 watt, storage type steel body with copper tank, puff insulation,both power indicating LED lamp and heating indicating LED lamp neccasry suitable 3 core copper cable,suitable plug top, inlcluding supply and fixing of inlet and out let connection to geyser with steel grip,chromium plated PVC connection of 450mm in length - 02 Nos (one for inlet GI pipe and other one for outlet connection) suitable to connect inlet GI pipe 15mm dia and out let GI pipe 15mm dia (out let PVC connection should be capable to withstand the designed temparature of Geyser) and geyser shall be fixed on wall surface with wall mount bracket and 10 cm anchor bolts as required inclduing all necessary plumbling works and civil works complete all as directed and as specified.

Supply, laying, testing & commissioing of cable XLPE insulated screened PVC beded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 2 core, complete all as specified and as directed. Note:- Earthwork, cable cover, sand cushioning work shall be measured and paid seperately

Supply and fix of GI tubing of size 40mm bore, medium grade for protection of cables on poles / under road crossing complete all as specified and as directed.

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type I, flat, size 300 mm x 180mm x 40mm complete laid over the cable perpendicular to the cable for protection, complete all as specified and as directed.

Supply and spreading clean dry sand in trenches for cushioning to PVC cable and punning to provide required cover to UG cable complete all as specified and directed . Note :- Punned thickness shall be measured for the purpose of payment.

Supply and install desert cooler electric driven (single phase) three speed having nominal air flow capacity 6000 CuM per hour (or nearest size), with propeller ISI cooler fan motor copper winding single phase fitted with/having aluminium blade of minimum size 500 mm, submersible pump, Max power consumption of 325 Watts Cooler body made out from 20 gauge mild steel galvanized iron sheet & water tank made out of 18 SWG, having capacity 40 Ltr minimum including three louvers with wood wool pad, flexible PVC distribution pipes and 3 way junction all as directed by Engr-in-Charge and of standard make as approved by GE" NOTE 1. Three speed switch ISI Marked rotary type for propeller fan and one way switch pump with separate control. The switches shall have marking off-Low-medium and high. 2 float valve on water supply connection shall be deemed to be included in unit rate quoted

M&L for stand, flush to wall for desert cooler, fabricated out of MS angle iron 40mm x 40mm x 06mm, 1,2 meter long bend to shape as top size 600mm x 600mm, duly welded with two members to tie vertical support, including painting two coats of synthetic enamelled paint over a coat of red oxide primer including M&L for steel rack bolts/ fastners, 100mm long, 12mm dia - 4 Nos for fixing stand all as directed

Supply and planting of Carpet Grass (Mexican Grass) with necessary ground preparation including developing the lawn designing up to 30cm deep and filling with red earth to a depth of 15 cm at bottom and 15 cm thick sand on top layer mixed with cow dung manure, pesticides & fungicides complete all as specified and directed by Engr-in-Charge. (Note:- Further maintenance of grass for two year from the date of completion including tools, materials, man power related machinery etc. complete as per the direction good growing of grass by watering as required specified and directed by Engr-in-Charge).

Supply and planting of hedges of height 30 cm and above, flower / plant of approved sapling species, 06 plants per running metre, including necessary ground preparation and developing of earth pit of size 45x45 cm, filling with farmyard manure, pesticides & Fungicides to the required quantity and quality complete all as specified and directed by Engr-in-Charge. (Note:- Further maintenance for two year from the date of completion including tools, materials, man power related machinery etc. complete as per the direction good growing the plants by watering as required for plant as directed by Engr-in-Charge.

The following varieties of plants/Trees (ornamental/Seasonable/Non Seasonable) are required to be planted M&L for planting of following trees plant/trees of mentioned height at the time of plantation including excavation in any type of soil for pit size (3 feet x 3 feet x 3 feet) application of Anti Termite Treatment and fill the pit putting DAP & Urea suitable for plant with the mixer of soil 50% blackcotton soil obtained from excavation 25% red/sweet agriculture soil and 25% cattle composed mannaure obtained from out side MD land as approved. Then planting the plants in the pit watering to plant and fill the wate in the pit till soil saturated with water as required for pleant. (Note:- The growing of plant by watering and removing the vegitation from the plant pit also till completation date of this contract agreement. Further maintenance for two year from the date of completation including tools, materials, man power related machinery etc. complete as per the direction good frowing the plants by watering as required for plant and removing the vegitation from the pits and keep all the plants healthy alive. If any plant has died then the same shall be replaced with the same age and height of other grown up plants under this CA) specified and directed by Engr-in-Charge.

Neem (Trees) (height 4-6 ft)

Gulmohar (Trees) (height 4-6 ft)

Supply and planting Phylanthus sapling having 15 to 30 cm height as per specified and directed by Engr-in-Charge.

Supply and planting colour flower plants sapling having 15 to 30cm height as per specified and directed by Engr-in-Charge.

Supply and planting Song of India flower plants sapling having 15 to 30cm height as per specified and directed by Engr-in-Charge.

Supply and planting Dracena flower plant sapling having 15 to 30cm height as per specified and directed by Engr-in-Charge. Note (For Sl No. 187 to 190):- Plant/flower pots (Decorative pots height of 18 inches) are provided as per specified and directed by Engr-in-Charge.

CHARPOY IP HARD TOP All as shown on drawing No. FD/MAP-II/01 The complete frame work shall be made of CRCA box section with 16 Gauge Charpoy top shall be 12 mm thick BWP Marine grade IS 710 plywood and fitted with suitable shunken type nuts and bolts with washer. Headrest and foot rest shall be detachable. All metal work shall be powder coated (black) welding process shall be of MIG MAG and complete. Std quality rubber shoe shall be provided to each legs. Rest all as shown on drg and as directed by EIC

CHAIR WRITING All as shown on drawing No. FD-280 All as shown on drawing Overall size shall be 535mm long, 470 mm wide and 890mm high. All wood shall be of first class hard wood teak Front leg shall be of 55mmx30mm in section and 660mm high up to bottom of arm rest. Rear legs shall be of 55mmx30mm in section and 890 mm high. The distance between outer legs in front side shall be 535mm and between outer side of legs at rear shall be 470mm. The legs shall be joined together at 460mm from bottom of legs by front, sides and rear rails, 30mm * 65mm in section made to shape as shown on drawing. Side stiffeners in 470mm side and at 100mm from bottom of legs shall be provided of 25mm * 20mm in section stiffeners. One stiffener of size 25mm * 20mm in section shall be provided in the middle of side stiffeners, joining side stiffeners. Two arm rest of 60mm * 25mm in section made to shape as shown on drawing shall peovided on the side arms. Two back horizontal rests 50mm * 15mm in section made slightly curved out of 50mm * 35mm in section wood shall be provided one at 20mm below the top of rear legs and other at 45mm below the bottom of uper top rest Canning shall be done with 2mm wide and 0.4mm thick half round cane woven as per Godrej pattern. All wood surfaces exposed to view when placed in position shall be melamine polished with high finish. Hard rubber/PVC rings of 25mm dia and 25mm high shall be screw to the bottom of all legs. Rest all as shown on drg and as directed by EIC.

LOCKER BED SIDE STEEL All as shown on drawing No. FD-1029 Overall size shall be 760mm long, 600mm wide and 1100mm high. All CRCA steel sheets shall be of 20 gauge thick. Irrespective of whatever is shown on drawing a three-way locking device controlled by a brass lever lock and operated by a chromium plated metallic S-Type handle-01 No shall be provided. All steel surfaces ext/int shall be provided with two coats of synthetic enameled paint over a coat of primer with spray machine after preparation of surfaces with putty. Contrast colour/ hammertone finish or as directed shall be applied on body and shutters. Colour shall be approved by GE Rest all as shown on drg and as directed by EIC

NOTE:- (i)- Quantities have been clubbed from 2 nos sanction Job, details as per APPX 'A'. (ii)- Qty's of Item No. 184.00 to 190.00 are only for Arboriculture Sl. No. 7 of Job No. 26 / LBW/ JODH/ 2023-24. (iii)- Qty's of Item No. 191.00 to 193.00 are only for Sl. No. 3 (Furniture) of Job No. 26 / LBW/ JODH/ 2023-24.

Nikhat nirman (BID ID -3136011)

M/S KAUTILYA GARG (BID ID -3141475)